| // SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause |
| /* |
| * Copyright (C) 2003-2014, 2018-2021 Intel Corporation |
| * Copyright (C) 2013-2015 Intel Mobile Communications GmbH |
| * Copyright (C) 2016-2017 Intel Deutschland GmbH |
| */ |
| #include <linux/etherdevice.h> |
| #include <linux/ieee80211.h> |
| #include <linux/slab.h> |
| #include <linux/sched.h> |
| #include <net/ip6_checksum.h> |
| #include <net/tso.h> |
| |
| #include "iwl-debug.h" |
| #include "iwl-csr.h" |
| #include "iwl-prph.h" |
| #include "iwl-io.h" |
| #include "iwl-scd.h" |
| #include "iwl-op-mode.h" |
| #include "internal.h" |
| #include "fw/api/tx.h" |
| |
| /*************** DMA-QUEUE-GENERAL-FUNCTIONS ***** |
| * DMA services |
| * |
| * Theory of operation |
| * |
| * A Tx or Rx queue resides in host DRAM, and is comprised of a circular buffer |
| * of buffer descriptors, each of which points to one or more data buffers for |
| * the device to read from or fill. Driver and device exchange status of each |
| * queue via "read" and "write" pointers. Driver keeps minimum of 2 empty |
| * entries in each circular buffer, to protect against confusing empty and full |
| * queue states. |
| * |
| * The device reads or writes the data in the queues via the device's several |
| * DMA/FIFO channels. Each queue is mapped to a single DMA channel. |
| * |
| * For Tx queue, there are low mark and high mark limits. If, after queuing |
| * the packet for Tx, free space become < low mark, Tx queue stopped. When |
| * reclaiming packets (on 'tx done IRQ), if free space become > high mark, |
| * Tx queue resumed. |
| * |
| ***************************************************/ |
| |
| |
| int iwl_pcie_alloc_dma_ptr(struct iwl_trans *trans, |
| struct iwl_dma_ptr *ptr, size_t size) |
| { |
| if (WARN_ON(ptr->addr)) |
| return -EINVAL; |
| |
| ptr->addr = dma_alloc_coherent(trans->dev, size, |
| &ptr->dma, GFP_KERNEL); |
| if (!ptr->addr) |
| return -ENOMEM; |
| ptr->size = size; |
| return 0; |
| } |
| |
| void iwl_pcie_free_dma_ptr(struct iwl_trans *trans, struct iwl_dma_ptr *ptr) |
| { |
| if (unlikely(!ptr->addr)) |
| return; |
| |
| dma_free_coherent(trans->dev, ptr->size, ptr->addr, ptr->dma); |
| memset(ptr, 0, sizeof(*ptr)); |
| } |
| |
| /* |
| * iwl_pcie_txq_inc_wr_ptr - Send new write index to hardware |
| */ |
| static void iwl_pcie_txq_inc_wr_ptr(struct iwl_trans *trans, |
| struct iwl_txq *txq) |
| { |
| u32 reg = 0; |
| int txq_id = txq->id; |
| |
| lockdep_assert_held(&txq->lock); |
| |
| /* |
| * explicitly wake up the NIC if: |
| * 1. shadow registers aren't enabled |
| * 2. NIC is woken up for CMD regardless of shadow outside this function |
| * 3. there is a chance that the NIC is asleep |
| */ |
| if (!trans->trans_cfg->base_params->shadow_reg_enable && |
| txq_id != trans->txqs.cmd.q_id && |
| test_bit(STATUS_TPOWER_PMI, &trans->status)) { |
| /* |
| * wake up nic if it's powered down ... |
| * uCode will wake up, and interrupt us again, so next |
| * time we'll skip this part. |
| */ |
| reg = iwl_read32(trans, CSR_UCODE_DRV_GP1); |
| |
| if (reg & CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP) { |
| IWL_DEBUG_INFO(trans, "Tx queue %d requesting wakeup, GP1 = 0x%x\n", |
| txq_id, reg); |
| iwl_set_bit(trans, CSR_GP_CNTRL, |
| CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ); |
| txq->need_update = true; |
| return; |
| } |
| } |
| |
| /* |
| * if not in power-save mode, uCode will never sleep when we're |
| * trying to tx (during RFKILL, we're not trying to tx). |
| */ |
| IWL_DEBUG_TX(trans, "Q:%d WR: 0x%x\n", txq_id, txq->write_ptr); |
| if (!txq->block) |
| iwl_write32(trans, HBUS_TARG_WRPTR, |
| txq->write_ptr | (txq_id << 8)); |
| } |
| |
| void iwl_pcie_txq_check_wrptrs(struct iwl_trans *trans) |
| { |
| int i; |
| |
| for (i = 0; i < trans->trans_cfg->base_params->num_of_queues; i++) { |
| struct iwl_txq *txq = trans->txqs.txq[i]; |
| |
| if (!test_bit(i, trans->txqs.queue_used)) |
| continue; |
| |
| spin_lock_bh(&txq->lock); |
| if (txq->need_update) { |
| iwl_pcie_txq_inc_wr_ptr(trans, txq); |
| txq->need_update = false; |
| } |
| spin_unlock_bh(&txq->lock); |
| } |
| } |
| |
| static inline void iwl_pcie_tfd_set_tb(struct iwl_trans *trans, void *tfd, |
| u8 idx, dma_addr_t addr, u16 len) |
| { |
| struct iwl_tfd *tfd_fh = (void *)tfd; |
| struct iwl_tfd_tb *tb = &tfd_fh->tbs[idx]; |
| |
| u16 hi_n_len = len << 4; |
| |
| put_unaligned_le32(addr, &tb->lo); |
| hi_n_len |= iwl_get_dma_hi_addr(addr); |
| |
| tb->hi_n_len = cpu_to_le16(hi_n_len); |
| |
| tfd_fh->num_tbs = idx + 1; |
| } |
| |
| static int iwl_pcie_txq_build_tfd(struct iwl_trans *trans, struct iwl_txq *txq, |
| dma_addr_t addr, u16 len, bool reset) |
| { |
| void *tfd; |
| u32 num_tbs; |
| |
| tfd = txq->tfds + trans->txqs.tfd.size * txq->write_ptr; |
| |
| if (reset) |
| memset(tfd, 0, trans->txqs.tfd.size); |
| |
| num_tbs = iwl_txq_gen1_tfd_get_num_tbs(trans, tfd); |
| |
| /* Each TFD can point to a maximum max_tbs Tx buffers */ |
| if (num_tbs >= trans->txqs.tfd.max_tbs) { |
| IWL_ERR(trans, "Error can not send more than %d chunks\n", |
| trans->txqs.tfd.max_tbs); |
| return -EINVAL; |
| } |
| |
| if (WARN(addr & ~IWL_TX_DMA_MASK, |
| "Unaligned address = %llx\n", (unsigned long long)addr)) |
| return -EINVAL; |
| |
| iwl_pcie_tfd_set_tb(trans, tfd, num_tbs, addr, len); |
| |
| return num_tbs; |
| } |
| |
| static void iwl_pcie_clear_cmd_in_flight(struct iwl_trans *trans) |
| { |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| |
| if (!trans->trans_cfg->base_params->apmg_wake_up_wa) |
| return; |
| |
| spin_lock(&trans_pcie->reg_lock); |
| |
| if (WARN_ON(!trans_pcie->cmd_hold_nic_awake)) { |
| spin_unlock(&trans_pcie->reg_lock); |
| return; |
| } |
| |
| trans_pcie->cmd_hold_nic_awake = false; |
| __iwl_trans_pcie_clear_bit(trans, CSR_GP_CNTRL, |
| CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ); |
| spin_unlock(&trans_pcie->reg_lock); |
| } |
| |
| /* |
| * iwl_pcie_txq_unmap - Unmap any remaining DMA mappings and free skb's |
| */ |
| static void iwl_pcie_txq_unmap(struct iwl_trans *trans, int txq_id) |
| { |
| struct iwl_txq *txq = trans->txqs.txq[txq_id]; |
| |
| if (!txq) { |
| IWL_ERR(trans, "Trying to free a queue that wasn't allocated?\n"); |
| return; |
| } |
| |
| spin_lock_bh(&txq->lock); |
| while (txq->write_ptr != txq->read_ptr) { |
| IWL_DEBUG_TX_REPLY(trans, "Q %d Free %d\n", |
| txq_id, txq->read_ptr); |
| |
| if (txq_id != trans->txqs.cmd.q_id) { |
| struct sk_buff *skb = txq->entries[txq->read_ptr].skb; |
| |
| if (WARN_ON_ONCE(!skb)) |
| continue; |
| |
| iwl_txq_free_tso_page(trans, skb); |
| } |
| iwl_txq_free_tfd(trans, txq); |
| txq->read_ptr = iwl_txq_inc_wrap(trans, txq->read_ptr); |
| |
| if (txq->read_ptr == txq->write_ptr && |
| txq_id == trans->txqs.cmd.q_id) |
| iwl_pcie_clear_cmd_in_flight(trans); |
| } |
| |
| while (!skb_queue_empty(&txq->overflow_q)) { |
| struct sk_buff *skb = __skb_dequeue(&txq->overflow_q); |
| |
| iwl_op_mode_free_skb(trans->op_mode, skb); |
| } |
| |
| spin_unlock_bh(&txq->lock); |
| |
| /* just in case - this queue may have been stopped */ |
| iwl_wake_queue(trans, txq); |
| } |
| |
| /* |
| * iwl_pcie_txq_free - Deallocate DMA queue. |
| * @txq: Transmit queue to deallocate. |
| * |
| * Empty queue by removing and destroying all BD's. |
| * Free all buffers. |
| * 0-fill, but do not free "txq" descriptor structure. |
| */ |
| static void iwl_pcie_txq_free(struct iwl_trans *trans, int txq_id) |
| { |
| struct iwl_txq *txq = trans->txqs.txq[txq_id]; |
| struct device *dev = trans->dev; |
| int i; |
| |
| if (WARN_ON(!txq)) |
| return; |
| |
| iwl_pcie_txq_unmap(trans, txq_id); |
| |
| /* De-alloc array of command/tx buffers */ |
| if (txq_id == trans->txqs.cmd.q_id) |
| for (i = 0; i < txq->n_window; i++) { |
| kfree_sensitive(txq->entries[i].cmd); |
| kfree_sensitive(txq->entries[i].free_buf); |
| } |
| |
| /* De-alloc circular buffer of TFDs */ |
| if (txq->tfds) { |
| dma_free_coherent(dev, |
| trans->txqs.tfd.size * |
| trans->trans_cfg->base_params->max_tfd_queue_size, |
| txq->tfds, txq->dma_addr); |
| txq->dma_addr = 0; |
| txq->tfds = NULL; |
| |
| dma_free_coherent(dev, |
| sizeof(*txq->first_tb_bufs) * txq->n_window, |
| txq->first_tb_bufs, txq->first_tb_dma); |
| } |
| |
| kfree(txq->entries); |
| txq->entries = NULL; |
| |
| del_timer_sync(&txq->stuck_timer); |
| |
| /* 0-fill queue descriptor structure */ |
| memset(txq, 0, sizeof(*txq)); |
| } |
| |
| void iwl_pcie_tx_start(struct iwl_trans *trans, u32 scd_base_addr) |
| { |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| int nq = trans->trans_cfg->base_params->num_of_queues; |
| int chan; |
| u32 reg_val; |
| int clear_dwords = (SCD_TRANS_TBL_OFFSET_QUEUE(nq) - |
| SCD_CONTEXT_MEM_LOWER_BOUND) / sizeof(u32); |
| |
| /* make sure all queue are not stopped/used */ |
| memset(trans->txqs.queue_stopped, 0, |
| sizeof(trans->txqs.queue_stopped)); |
| memset(trans->txqs.queue_used, 0, sizeof(trans->txqs.queue_used)); |
| |
| trans_pcie->scd_base_addr = |
| iwl_read_prph(trans, SCD_SRAM_BASE_ADDR); |
| |
| WARN_ON(scd_base_addr != 0 && |
| scd_base_addr != trans_pcie->scd_base_addr); |
| |
| /* reset context data, TX status and translation data */ |
| iwl_trans_write_mem(trans, trans_pcie->scd_base_addr + |
| SCD_CONTEXT_MEM_LOWER_BOUND, |
| NULL, clear_dwords); |
| |
| iwl_write_prph(trans, SCD_DRAM_BASE_ADDR, |
| trans->txqs.scd_bc_tbls.dma >> 10); |
| |
| /* The chain extension of the SCD doesn't work well. This feature is |
| * enabled by default by the HW, so we need to disable it manually. |
| */ |
| if (trans->trans_cfg->base_params->scd_chain_ext_wa) |
| iwl_write_prph(trans, SCD_CHAINEXT_EN, 0); |
| |
| iwl_trans_ac_txq_enable(trans, trans->txqs.cmd.q_id, |
| trans->txqs.cmd.fifo, |
| trans->txqs.cmd.wdg_timeout); |
| |
| /* Activate all Tx DMA/FIFO channels */ |
| iwl_scd_activate_fifos(trans); |
| |
| /* Enable DMA channel */ |
| for (chan = 0; chan < FH_TCSR_CHNL_NUM; chan++) |
| iwl_write_direct32(trans, FH_TCSR_CHNL_TX_CONFIG_REG(chan), |
| FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE | |
| FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE); |
| |
| /* Update FH chicken bits */ |
| reg_val = iwl_read_direct32(trans, FH_TX_CHICKEN_BITS_REG); |
| iwl_write_direct32(trans, FH_TX_CHICKEN_BITS_REG, |
| reg_val | FH_TX_CHICKEN_BITS_SCD_AUTO_RETRY_EN); |
| |
| /* Enable L1-Active */ |
| if (trans->trans_cfg->device_family < IWL_DEVICE_FAMILY_8000) |
| iwl_clear_bits_prph(trans, APMG_PCIDEV_STT_REG, |
| APMG_PCIDEV_STT_VAL_L1_ACT_DIS); |
| } |
| |
| void iwl_trans_pcie_tx_reset(struct iwl_trans *trans) |
| { |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| int txq_id; |
| |
| /* |
| * we should never get here in gen2 trans mode return early to avoid |
| * having invalid accesses |
| */ |
| if (WARN_ON_ONCE(trans->trans_cfg->gen2)) |
| return; |
| |
| for (txq_id = 0; txq_id < trans->trans_cfg->base_params->num_of_queues; |
| txq_id++) { |
| struct iwl_txq *txq = trans->txqs.txq[txq_id]; |
| if (trans->trans_cfg->use_tfh) |
| iwl_write_direct64(trans, |
| FH_MEM_CBBC_QUEUE(trans, txq_id), |
| txq->dma_addr); |
| else |
| iwl_write_direct32(trans, |
| FH_MEM_CBBC_QUEUE(trans, txq_id), |
| txq->dma_addr >> 8); |
| iwl_pcie_txq_unmap(trans, txq_id); |
| txq->read_ptr = 0; |
| txq->write_ptr = 0; |
| } |
| |
| /* Tell NIC where to find the "keep warm" buffer */ |
| iwl_write_direct32(trans, FH_KW_MEM_ADDR_REG, |
| trans_pcie->kw.dma >> 4); |
| |
| /* |
| * Send 0 as the scd_base_addr since the device may have be reset |
| * while we were in WoWLAN in which case SCD_SRAM_BASE_ADDR will |
| * contain garbage. |
| */ |
| iwl_pcie_tx_start(trans, 0); |
| } |
| |
| static void iwl_pcie_tx_stop_fh(struct iwl_trans *trans) |
| { |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| int ch, ret; |
| u32 mask = 0; |
| |
| spin_lock_bh(&trans_pcie->irq_lock); |
| |
| if (!iwl_trans_grab_nic_access(trans)) |
| goto out; |
| |
| /* Stop each Tx DMA channel */ |
| for (ch = 0; ch < FH_TCSR_CHNL_NUM; ch++) { |
| iwl_write32(trans, FH_TCSR_CHNL_TX_CONFIG_REG(ch), 0x0); |
| mask |= FH_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(ch); |
| } |
| |
| /* Wait for DMA channels to be idle */ |
| ret = iwl_poll_bit(trans, FH_TSSR_TX_STATUS_REG, mask, mask, 5000); |
| if (ret < 0) |
| IWL_ERR(trans, |
| "Failing on timeout while stopping DMA channel %d [0x%08x]\n", |
| ch, iwl_read32(trans, FH_TSSR_TX_STATUS_REG)); |
| |
| iwl_trans_release_nic_access(trans); |
| |
| out: |
| spin_unlock_bh(&trans_pcie->irq_lock); |
| } |
| |
| /* |
| * iwl_pcie_tx_stop - Stop all Tx DMA channels |
| */ |
| int iwl_pcie_tx_stop(struct iwl_trans *trans) |
| { |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| int txq_id; |
| |
| /* Turn off all Tx DMA fifos */ |
| iwl_scd_deactivate_fifos(trans); |
| |
| /* Turn off all Tx DMA channels */ |
| iwl_pcie_tx_stop_fh(trans); |
| |
| /* |
| * This function can be called before the op_mode disabled the |
| * queues. This happens when we have an rfkill interrupt. |
| * Since we stop Tx altogether - mark the queues as stopped. |
| */ |
| memset(trans->txqs.queue_stopped, 0, |
| sizeof(trans->txqs.queue_stopped)); |
| memset(trans->txqs.queue_used, 0, sizeof(trans->txqs.queue_used)); |
| |
| /* This can happen: start_hw, stop_device */ |
| if (!trans_pcie->txq_memory) |
| return 0; |
| |
| /* Unmap DMA from host system and free skb's */ |
| for (txq_id = 0; txq_id < trans->trans_cfg->base_params->num_of_queues; |
| txq_id++) |
| iwl_pcie_txq_unmap(trans, txq_id); |
| |
| return 0; |
| } |
| |
| /* |
| * iwl_trans_tx_free - Free TXQ Context |
| * |
| * Destroy all TX DMA queues and structures |
| */ |
| void iwl_pcie_tx_free(struct iwl_trans *trans) |
| { |
| int txq_id; |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| |
| memset(trans->txqs.queue_used, 0, sizeof(trans->txqs.queue_used)); |
| |
| /* Tx queues */ |
| if (trans_pcie->txq_memory) { |
| for (txq_id = 0; |
| txq_id < trans->trans_cfg->base_params->num_of_queues; |
| txq_id++) { |
| iwl_pcie_txq_free(trans, txq_id); |
| trans->txqs.txq[txq_id] = NULL; |
| } |
| } |
| |
| kfree(trans_pcie->txq_memory); |
| trans_pcie->txq_memory = NULL; |
| |
| iwl_pcie_free_dma_ptr(trans, &trans_pcie->kw); |
| |
| iwl_pcie_free_dma_ptr(trans, &trans->txqs.scd_bc_tbls); |
| } |
| |
| /* |
| * iwl_pcie_tx_alloc - allocate TX context |
| * Allocate all Tx DMA structures and initialize them |
| */ |
| static int iwl_pcie_tx_alloc(struct iwl_trans *trans) |
| { |
| int ret; |
| int txq_id, slots_num; |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| u16 bc_tbls_size = trans->trans_cfg->base_params->num_of_queues; |
| |
| if (WARN_ON(trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210)) |
| return -EINVAL; |
| |
| bc_tbls_size *= sizeof(struct iwlagn_scd_bc_tbl); |
| |
| /*It is not allowed to alloc twice, so warn when this happens. |
| * We cannot rely on the previous allocation, so free and fail */ |
| if (WARN_ON(trans_pcie->txq_memory)) { |
| ret = -EINVAL; |
| goto error; |
| } |
| |
| ret = iwl_pcie_alloc_dma_ptr(trans, &trans->txqs.scd_bc_tbls, |
| bc_tbls_size); |
| if (ret) { |
| IWL_ERR(trans, "Scheduler BC Table allocation failed\n"); |
| goto error; |
| } |
| |
| /* Alloc keep-warm buffer */ |
| ret = iwl_pcie_alloc_dma_ptr(trans, &trans_pcie->kw, IWL_KW_SIZE); |
| if (ret) { |
| IWL_ERR(trans, "Keep Warm allocation failed\n"); |
| goto error; |
| } |
| |
| trans_pcie->txq_memory = |
| kcalloc(trans->trans_cfg->base_params->num_of_queues, |
| sizeof(struct iwl_txq), GFP_KERNEL); |
| if (!trans_pcie->txq_memory) { |
| IWL_ERR(trans, "Not enough memory for txq\n"); |
| ret = -ENOMEM; |
| goto error; |
| } |
| |
| /* Alloc and init all Tx queues, including the command queue (#4/#9) */ |
| for (txq_id = 0; txq_id < trans->trans_cfg->base_params->num_of_queues; |
| txq_id++) { |
| bool cmd_queue = (txq_id == trans->txqs.cmd.q_id); |
| |
| if (cmd_queue) |
| slots_num = max_t(u32, IWL_CMD_QUEUE_SIZE, |
| trans->cfg->min_txq_size); |
| else |
| slots_num = max_t(u32, IWL_DEFAULT_QUEUE_SIZE, |
| trans->cfg->min_256_ba_txq_size); |
| trans->txqs.txq[txq_id] = &trans_pcie->txq_memory[txq_id]; |
| ret = iwl_txq_alloc(trans, trans->txqs.txq[txq_id], slots_num, |
| cmd_queue); |
| if (ret) { |
| IWL_ERR(trans, "Tx %d queue alloc failed\n", txq_id); |
| goto error; |
| } |
| trans->txqs.txq[txq_id]->id = txq_id; |
| } |
| |
| return 0; |
| |
| error: |
| iwl_pcie_tx_free(trans); |
| |
| return ret; |
| } |
| |
| int iwl_pcie_tx_init(struct iwl_trans *trans) |
| { |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| int ret; |
| int txq_id, slots_num; |
| bool alloc = false; |
| |
| if (!trans_pcie->txq_memory) { |
| ret = iwl_pcie_tx_alloc(trans); |
| if (ret) |
| goto error; |
| alloc = true; |
| } |
| |
| spin_lock_bh(&trans_pcie->irq_lock); |
| |
| /* Turn off all Tx DMA fifos */ |
| iwl_scd_deactivate_fifos(trans); |
| |
| /* Tell NIC where to find the "keep warm" buffer */ |
| iwl_write_direct32(trans, FH_KW_MEM_ADDR_REG, |
| trans_pcie->kw.dma >> 4); |
| |
| spin_unlock_bh(&trans_pcie->irq_lock); |
| |
| /* Alloc and init all Tx queues, including the command queue (#4/#9) */ |
| for (txq_id = 0; txq_id < trans->trans_cfg->base_params->num_of_queues; |
| txq_id++) { |
| bool cmd_queue = (txq_id == trans->txqs.cmd.q_id); |
| |
| if (cmd_queue) |
| slots_num = max_t(u32, IWL_CMD_QUEUE_SIZE, |
| trans->cfg->min_txq_size); |
| else |
| slots_num = max_t(u32, IWL_DEFAULT_QUEUE_SIZE, |
| trans->cfg->min_256_ba_txq_size); |
| ret = iwl_txq_init(trans, trans->txqs.txq[txq_id], slots_num, |
| cmd_queue); |
| if (ret) { |
| IWL_ERR(trans, "Tx %d queue init failed\n", txq_id); |
| goto error; |
| } |
| |
| /* |
| * Tell nic where to find circular buffer of TFDs for a |
| * given Tx queue, and enable the DMA channel used for that |
| * queue. |
| * Circular buffer (TFD queue in DRAM) physical base address |
| */ |
| iwl_write_direct32(trans, FH_MEM_CBBC_QUEUE(trans, txq_id), |
| trans->txqs.txq[txq_id]->dma_addr >> 8); |
| } |
| |
| iwl_set_bits_prph(trans, SCD_GP_CTRL, SCD_GP_CTRL_AUTO_ACTIVE_MODE); |
| if (trans->trans_cfg->base_params->num_of_queues > 20) |
| iwl_set_bits_prph(trans, SCD_GP_CTRL, |
| SCD_GP_CTRL_ENABLE_31_QUEUES); |
| |
| return 0; |
| error: |
| /*Upon error, free only if we allocated something */ |
| if (alloc) |
| iwl_pcie_tx_free(trans); |
| return ret; |
| } |
| |
| static int iwl_pcie_set_cmd_in_flight(struct iwl_trans *trans, |
| const struct iwl_host_cmd *cmd) |
| { |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| |
| /* Make sure the NIC is still alive in the bus */ |
| if (test_bit(STATUS_TRANS_DEAD, &trans->status)) |
| return -ENODEV; |
| |
| if (!trans->trans_cfg->base_params->apmg_wake_up_wa) |
| return 0; |
| |
| /* |
| * wake up the NIC to make sure that the firmware will see the host |
| * command - we will let the NIC sleep once all the host commands |
| * returned. This needs to be done only on NICs that have |
| * apmg_wake_up_wa set (see above.) |
| */ |
| if (!_iwl_trans_pcie_grab_nic_access(trans)) |
| return -EIO; |
| |
| /* |
| * In iwl_trans_grab_nic_access(), we've acquired the reg_lock. |
| * There, we also returned immediately if cmd_hold_nic_awake is |
| * already true, so it's OK to unconditionally set it to true. |
| */ |
| trans_pcie->cmd_hold_nic_awake = true; |
| spin_unlock(&trans_pcie->reg_lock); |
| |
| return 0; |
| } |
| |
| /* |
| * iwl_pcie_cmdq_reclaim - Reclaim TX command queue entries already Tx'd |
| * |
| * When FW advances 'R' index, all entries between old and new 'R' index |
| * need to be reclaimed. As result, some free space forms. If there is |
| * enough free space (> low mark), wake the stack that feeds us. |
| */ |
| static void iwl_pcie_cmdq_reclaim(struct iwl_trans *trans, int txq_id, int idx) |
| { |
| struct iwl_txq *txq = trans->txqs.txq[txq_id]; |
| int nfreed = 0; |
| u16 r; |
| |
| lockdep_assert_held(&txq->lock); |
| |
| idx = iwl_txq_get_cmd_index(txq, idx); |
| r = iwl_txq_get_cmd_index(txq, txq->read_ptr); |
| |
| if (idx >= trans->trans_cfg->base_params->max_tfd_queue_size || |
| (!iwl_txq_used(txq, idx))) { |
| WARN_ONCE(test_bit(txq_id, trans->txqs.queue_used), |
| "%s: Read index for DMA queue txq id (%d), index %d is out of range [0-%d] %d %d.\n", |
| __func__, txq_id, idx, |
| trans->trans_cfg->base_params->max_tfd_queue_size, |
| txq->write_ptr, txq->read_ptr); |
| return; |
| } |
| |
| for (idx = iwl_txq_inc_wrap(trans, idx); r != idx; |
| r = iwl_txq_inc_wrap(trans, r)) { |
| txq->read_ptr = iwl_txq_inc_wrap(trans, txq->read_ptr); |
| |
| if (nfreed++ > 0) { |
| IWL_ERR(trans, "HCMD skipped: index (%d) %d %d\n", |
| idx, txq->write_ptr, r); |
| iwl_force_nmi(trans); |
| } |
| } |
| |
| if (txq->read_ptr == txq->write_ptr) |
| iwl_pcie_clear_cmd_in_flight(trans); |
| |
| iwl_txq_progress(txq); |
| } |
| |
| static int iwl_pcie_txq_set_ratid_map(struct iwl_trans *trans, u16 ra_tid, |
| u16 txq_id) |
| { |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| u32 tbl_dw_addr; |
| u32 tbl_dw; |
| u16 scd_q2ratid; |
| |
| scd_q2ratid = ra_tid & SCD_QUEUE_RA_TID_MAP_RATID_MSK; |
| |
| tbl_dw_addr = trans_pcie->scd_base_addr + |
| SCD_TRANS_TBL_OFFSET_QUEUE(txq_id); |
| |
| tbl_dw = iwl_trans_read_mem32(trans, tbl_dw_addr); |
| |
| if (txq_id & 0x1) |
| tbl_dw = (scd_q2ratid << 16) | (tbl_dw & 0x0000FFFF); |
| else |
| tbl_dw = scd_q2ratid | (tbl_dw & 0xFFFF0000); |
| |
| iwl_trans_write_mem32(trans, tbl_dw_addr, tbl_dw); |
| |
| return 0; |
| } |
| |
| /* Receiver address (actually, Rx station's index into station table), |
| * combined with Traffic ID (QOS priority), in format used by Tx Scheduler */ |
| #define BUILD_RAxTID(sta_id, tid) (((sta_id) << 4) + (tid)) |
| |
| bool iwl_trans_pcie_txq_enable(struct iwl_trans *trans, int txq_id, u16 ssn, |
| const struct iwl_trans_txq_scd_cfg *cfg, |
| unsigned int wdg_timeout) |
| { |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| struct iwl_txq *txq = trans->txqs.txq[txq_id]; |
| int fifo = -1; |
| bool scd_bug = false; |
| |
| if (test_and_set_bit(txq_id, trans->txqs.queue_used)) |
| WARN_ONCE(1, "queue %d already used - expect issues", txq_id); |
| |
| txq->wd_timeout = msecs_to_jiffies(wdg_timeout); |
| |
| if (cfg) { |
| fifo = cfg->fifo; |
| |
| /* Disable the scheduler prior configuring the cmd queue */ |
| if (txq_id == trans->txqs.cmd.q_id && |
| trans_pcie->scd_set_active) |
| iwl_scd_enable_set_active(trans, 0); |
| |
| /* Stop this Tx queue before configuring it */ |
| iwl_scd_txq_set_inactive(trans, txq_id); |
| |
| /* Set this queue as a chain-building queue unless it is CMD */ |
| if (txq_id != trans->txqs.cmd.q_id) |
| iwl_scd_txq_set_chain(trans, txq_id); |
| |
| if (cfg->aggregate) { |
| u16 ra_tid = BUILD_RAxTID(cfg->sta_id, cfg->tid); |
| |
| /* Map receiver-address / traffic-ID to this queue */ |
| iwl_pcie_txq_set_ratid_map(trans, ra_tid, txq_id); |
| |
| /* enable aggregations for the queue */ |
| iwl_scd_txq_enable_agg(trans, txq_id); |
| txq->ampdu = true; |
| } else { |
| /* |
| * disable aggregations for the queue, this will also |
| * make the ra_tid mapping configuration irrelevant |
| * since it is now a non-AGG queue. |
| */ |
| iwl_scd_txq_disable_agg(trans, txq_id); |
| |
| ssn = txq->read_ptr; |
| } |
| } else { |
| /* |
| * If we need to move the SCD write pointer by steps of |
| * 0x40, 0x80 or 0xc0, it gets stuck. Avoids this and let |
| * the op_mode know by returning true later. |
| * Do this only in case cfg is NULL since this trick can |
| * be done only if we have DQA enabled which is true for mvm |
| * only. And mvm never sets a cfg pointer. |
| * This is really ugly, but this is the easiest way out for |
| * this sad hardware issue. |
| * This bug has been fixed on devices 9000 and up. |
| */ |
| scd_bug = !trans->trans_cfg->mq_rx_supported && |
| !((ssn - txq->write_ptr) & 0x3f) && |
| (ssn != txq->write_ptr); |
| if (scd_bug) |
| ssn++; |
| } |
| |
| /* Place first TFD at index corresponding to start sequence number. |
| * Assumes that ssn_idx is valid (!= 0xFFF) */ |
| txq->read_ptr = (ssn & 0xff); |
| txq->write_ptr = (ssn & 0xff); |
| iwl_write_direct32(trans, HBUS_TARG_WRPTR, |
| (ssn & 0xff) | (txq_id << 8)); |
| |
| if (cfg) { |
| u8 frame_limit = cfg->frame_limit; |
| |
| iwl_write_prph(trans, SCD_QUEUE_RDPTR(txq_id), ssn); |
| |
| /* Set up Tx window size and frame limit for this queue */ |
| iwl_trans_write_mem32(trans, trans_pcie->scd_base_addr + |
| SCD_CONTEXT_QUEUE_OFFSET(txq_id), 0); |
| iwl_trans_write_mem32(trans, |
| trans_pcie->scd_base_addr + |
| SCD_CONTEXT_QUEUE_OFFSET(txq_id) + sizeof(u32), |
| SCD_QUEUE_CTX_REG2_VAL(WIN_SIZE, frame_limit) | |
| SCD_QUEUE_CTX_REG2_VAL(FRAME_LIMIT, frame_limit)); |
| |
| /* Set up status area in SRAM, map to Tx DMA/FIFO, activate */ |
| iwl_write_prph(trans, SCD_QUEUE_STATUS_BITS(txq_id), |
| (1 << SCD_QUEUE_STTS_REG_POS_ACTIVE) | |
| (cfg->fifo << SCD_QUEUE_STTS_REG_POS_TXF) | |
| (1 << SCD_QUEUE_STTS_REG_POS_WSL) | |
| SCD_QUEUE_STTS_REG_MSK); |
| |
| /* enable the scheduler for this queue (only) */ |
| if (txq_id == trans->txqs.cmd.q_id && |
| trans_pcie->scd_set_active) |
| iwl_scd_enable_set_active(trans, BIT(txq_id)); |
| |
| IWL_DEBUG_TX_QUEUES(trans, |
| "Activate queue %d on FIFO %d WrPtr: %d\n", |
| txq_id, fifo, ssn & 0xff); |
| } else { |
| IWL_DEBUG_TX_QUEUES(trans, |
| "Activate queue %d WrPtr: %d\n", |
| txq_id, ssn & 0xff); |
| } |
| |
| return scd_bug; |
| } |
| |
| void iwl_trans_pcie_txq_set_shared_mode(struct iwl_trans *trans, u32 txq_id, |
| bool shared_mode) |
| { |
| struct iwl_txq *txq = trans->txqs.txq[txq_id]; |
| |
| txq->ampdu = !shared_mode; |
| } |
| |
| void iwl_trans_pcie_txq_disable(struct iwl_trans *trans, int txq_id, |
| bool configure_scd) |
| { |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| u32 stts_addr = trans_pcie->scd_base_addr + |
| SCD_TX_STTS_QUEUE_OFFSET(txq_id); |
| static const u32 zero_val[4] = {}; |
| |
| trans->txqs.txq[txq_id]->frozen_expiry_remainder = 0; |
| trans->txqs.txq[txq_id]->frozen = false; |
| |
| /* |
| * Upon HW Rfkill - we stop the device, and then stop the queues |
| * in the op_mode. Just for the sake of the simplicity of the op_mode, |
| * allow the op_mode to call txq_disable after it already called |
| * stop_device. |
| */ |
| if (!test_and_clear_bit(txq_id, trans->txqs.queue_used)) { |
| WARN_ONCE(test_bit(STATUS_DEVICE_ENABLED, &trans->status), |
| "queue %d not used", txq_id); |
| return; |
| } |
| |
| if (configure_scd) { |
| iwl_scd_txq_set_inactive(trans, txq_id); |
| |
| iwl_trans_write_mem(trans, stts_addr, (void *)zero_val, |
| ARRAY_SIZE(zero_val)); |
| } |
| |
| iwl_pcie_txq_unmap(trans, txq_id); |
| trans->txqs.txq[txq_id]->ampdu = false; |
| |
| IWL_DEBUG_TX_QUEUES(trans, "Deactivate queue %d\n", txq_id); |
| } |
| |
| /*************** HOST COMMAND QUEUE FUNCTIONS *****/ |
| |
| /* |
| * iwl_pcie_enqueue_hcmd - enqueue a uCode command |
| * @priv: device private data point |
| * @cmd: a pointer to the ucode command structure |
| * |
| * The function returns < 0 values to indicate the operation |
| * failed. On success, it returns the index (>= 0) of command in the |
| * command queue. |
| */ |
| int iwl_pcie_enqueue_hcmd(struct iwl_trans *trans, |
| struct iwl_host_cmd *cmd) |
| { |
| struct iwl_txq *txq = trans->txqs.txq[trans->txqs.cmd.q_id]; |
| struct iwl_device_cmd *out_cmd; |
| struct iwl_cmd_meta *out_meta; |
| void *dup_buf = NULL; |
| dma_addr_t phys_addr; |
| int idx; |
| u16 copy_size, cmd_size, tb0_size; |
| bool had_nocopy = false; |
| u8 group_id = iwl_cmd_groupid(cmd->id); |
| int i, ret; |
| u32 cmd_pos; |
| const u8 *cmddata[IWL_MAX_CMD_TBS_PER_TFD]; |
| u16 cmdlen[IWL_MAX_CMD_TBS_PER_TFD]; |
| unsigned long flags; |
| |
| if (WARN(!trans->wide_cmd_header && |
| group_id > IWL_ALWAYS_LONG_GROUP, |
| "unsupported wide command %#x\n", cmd->id)) |
| return -EINVAL; |
| |
| if (group_id != 0) { |
| copy_size = sizeof(struct iwl_cmd_header_wide); |
| cmd_size = sizeof(struct iwl_cmd_header_wide); |
| } else { |
| copy_size = sizeof(struct iwl_cmd_header); |
| cmd_size = sizeof(struct iwl_cmd_header); |
| } |
| |
| /* need one for the header if the first is NOCOPY */ |
| BUILD_BUG_ON(IWL_MAX_CMD_TBS_PER_TFD > IWL_NUM_OF_TBS - 1); |
| |
| for (i = 0; i < IWL_MAX_CMD_TBS_PER_TFD; i++) { |
| cmddata[i] = cmd->data[i]; |
| cmdlen[i] = cmd->len[i]; |
| |
| if (!cmd->len[i]) |
| continue; |
| |
| /* need at least IWL_FIRST_TB_SIZE copied */ |
| if (copy_size < IWL_FIRST_TB_SIZE) { |
| int copy = IWL_FIRST_TB_SIZE - copy_size; |
| |
| if (copy > cmdlen[i]) |
| copy = cmdlen[i]; |
| cmdlen[i] -= copy; |
| cmddata[i] += copy; |
| copy_size += copy; |
| } |
| |
| if (cmd->dataflags[i] & IWL_HCMD_DFL_NOCOPY) { |
| had_nocopy = true; |
| if (WARN_ON(cmd->dataflags[i] & IWL_HCMD_DFL_DUP)) { |
| idx = -EINVAL; |
| goto free_dup_buf; |
| } |
| } else if (cmd->dataflags[i] & IWL_HCMD_DFL_DUP) { |
| /* |
| * This is also a chunk that isn't copied |
| * to the static buffer so set had_nocopy. |
| */ |
| had_nocopy = true; |
| |
| /* only allowed once */ |
| if (WARN_ON(dup_buf)) { |
| idx = -EINVAL; |
| goto free_dup_buf; |
| } |
| |
| dup_buf = kmemdup(cmddata[i], cmdlen[i], |
| GFP_ATOMIC); |
| if (!dup_buf) |
| return -ENOMEM; |
| } else { |
| /* NOCOPY must not be followed by normal! */ |
| if (WARN_ON(had_nocopy)) { |
| idx = -EINVAL; |
| goto free_dup_buf; |
| } |
| copy_size += cmdlen[i]; |
| } |
| cmd_size += cmd->len[i]; |
| } |
| |
| /* |
| * If any of the command structures end up being larger than |
| * the TFD_MAX_PAYLOAD_SIZE and they aren't dynamically |
| * allocated into separate TFDs, then we will need to |
| * increase the size of the buffers. |
| */ |
| if (WARN(copy_size > TFD_MAX_PAYLOAD_SIZE, |
| "Command %s (%#x) is too large (%d bytes)\n", |
| iwl_get_cmd_string(trans, cmd->id), |
| cmd->id, copy_size)) { |
| idx = -EINVAL; |
| goto free_dup_buf; |
| } |
| |
| spin_lock_irqsave(&txq->lock, flags); |
| |
| if (iwl_txq_space(trans, txq) < ((cmd->flags & CMD_ASYNC) ? 2 : 1)) { |
| spin_unlock_irqrestore(&txq->lock, flags); |
| |
| IWL_ERR(trans, "No space in command queue\n"); |
| iwl_op_mode_cmd_queue_full(trans->op_mode); |
| idx = -ENOSPC; |
| goto free_dup_buf; |
| } |
| |
| idx = iwl_txq_get_cmd_index(txq, txq->write_ptr); |
| out_cmd = txq->entries[idx].cmd; |
| out_meta = &txq->entries[idx].meta; |
| |
| memset(out_meta, 0, sizeof(*out_meta)); /* re-initialize to NULL */ |
| if (cmd->flags & CMD_WANT_SKB) |
| out_meta->source = cmd; |
| |
| /* set up the header */ |
| if (group_id != 0) { |
| out_cmd->hdr_wide.cmd = iwl_cmd_opcode(cmd->id); |
| out_cmd->hdr_wide.group_id = group_id; |
| out_cmd->hdr_wide.version = iwl_cmd_version(cmd->id); |
| out_cmd->hdr_wide.length = |
| cpu_to_le16(cmd_size - |
| sizeof(struct iwl_cmd_header_wide)); |
| out_cmd->hdr_wide.reserved = 0; |
| out_cmd->hdr_wide.sequence = |
| cpu_to_le16(QUEUE_TO_SEQ(trans->txqs.cmd.q_id) | |
| INDEX_TO_SEQ(txq->write_ptr)); |
| |
| cmd_pos = sizeof(struct iwl_cmd_header_wide); |
| copy_size = sizeof(struct iwl_cmd_header_wide); |
| } else { |
| out_cmd->hdr.cmd = iwl_cmd_opcode(cmd->id); |
| out_cmd->hdr.sequence = |
| cpu_to_le16(QUEUE_TO_SEQ(trans->txqs.cmd.q_id) | |
| INDEX_TO_SEQ(txq->write_ptr)); |
| out_cmd->hdr.group_id = 0; |
| |
| cmd_pos = sizeof(struct iwl_cmd_header); |
| copy_size = sizeof(struct iwl_cmd_header); |
| } |
| |
| /* and copy the data that needs to be copied */ |
| for (i = 0; i < IWL_MAX_CMD_TBS_PER_TFD; i++) { |
| int copy; |
| |
| if (!cmd->len[i]) |
| continue; |
| |
| /* copy everything if not nocopy/dup */ |
| if (!(cmd->dataflags[i] & (IWL_HCMD_DFL_NOCOPY | |
| IWL_HCMD_DFL_DUP))) { |
| copy = cmd->len[i]; |
| |
| memcpy((u8 *)out_cmd + cmd_pos, cmd->data[i], copy); |
| cmd_pos += copy; |
| copy_size += copy; |
| continue; |
| } |
| |
| /* |
| * Otherwise we need at least IWL_FIRST_TB_SIZE copied |
| * in total (for bi-directional DMA), but copy up to what |
| * we can fit into the payload for debug dump purposes. |
| */ |
| copy = min_t(int, TFD_MAX_PAYLOAD_SIZE - cmd_pos, cmd->len[i]); |
| |
| memcpy((u8 *)out_cmd + cmd_pos, cmd->data[i], copy); |
| cmd_pos += copy; |
| |
| /* However, treat copy_size the proper way, we need it below */ |
| if (copy_size < IWL_FIRST_TB_SIZE) { |
| copy = IWL_FIRST_TB_SIZE - copy_size; |
| |
| if (copy > cmd->len[i]) |
| copy = cmd->len[i]; |
| copy_size += copy; |
| } |
| } |
| |
| IWL_DEBUG_HC(trans, |
| "Sending command %s (%.2x.%.2x), seq: 0x%04X, %d bytes at %d[%d]:%d\n", |
| iwl_get_cmd_string(trans, cmd->id), |
| group_id, out_cmd->hdr.cmd, |
| le16_to_cpu(out_cmd->hdr.sequence), |
| cmd_size, txq->write_ptr, idx, trans->txqs.cmd.q_id); |
| |
| /* start the TFD with the minimum copy bytes */ |
| tb0_size = min_t(int, copy_size, IWL_FIRST_TB_SIZE); |
| memcpy(&txq->first_tb_bufs[idx], &out_cmd->hdr, tb0_size); |
| iwl_pcie_txq_build_tfd(trans, txq, |
| iwl_txq_get_first_tb_dma(txq, idx), |
| tb0_size, true); |
| |
| /* map first command fragment, if any remains */ |
| if (copy_size > tb0_size) { |
| phys_addr = dma_map_single(trans->dev, |
| ((u8 *)&out_cmd->hdr) + tb0_size, |
| copy_size - tb0_size, |
| DMA_TO_DEVICE); |
| if (dma_mapping_error(trans->dev, phys_addr)) { |
| iwl_txq_gen1_tfd_unmap(trans, out_meta, txq, |
| txq->write_ptr); |
| idx = -ENOMEM; |
| goto out; |
| } |
| |
| iwl_pcie_txq_build_tfd(trans, txq, phys_addr, |
| copy_size - tb0_size, false); |
| } |
| |
| /* map the remaining (adjusted) nocopy/dup fragments */ |
| for (i = 0; i < IWL_MAX_CMD_TBS_PER_TFD; i++) { |
| const void *data = cmddata[i]; |
| |
| if (!cmdlen[i]) |
| continue; |
| if (!(cmd->dataflags[i] & (IWL_HCMD_DFL_NOCOPY | |
| IWL_HCMD_DFL_DUP))) |
| continue; |
| if (cmd->dataflags[i] & IWL_HCMD_DFL_DUP) |
| data = dup_buf; |
| phys_addr = dma_map_single(trans->dev, (void *)data, |
| cmdlen[i], DMA_TO_DEVICE); |
| if (dma_mapping_error(trans->dev, phys_addr)) { |
| iwl_txq_gen1_tfd_unmap(trans, out_meta, txq, |
| txq->write_ptr); |
| idx = -ENOMEM; |
| goto out; |
| } |
| |
| iwl_pcie_txq_build_tfd(trans, txq, phys_addr, cmdlen[i], false); |
| } |
| |
| BUILD_BUG_ON(IWL_TFH_NUM_TBS > sizeof(out_meta->tbs) * BITS_PER_BYTE); |
| out_meta->flags = cmd->flags; |
| if (WARN_ON_ONCE(txq->entries[idx].free_buf)) |
| kfree_sensitive(txq->entries[idx].free_buf); |
| txq->entries[idx].free_buf = dup_buf; |
| |
| trace_iwlwifi_dev_hcmd(trans->dev, cmd, cmd_size, &out_cmd->hdr_wide); |
| |
| /* start timer if queue currently empty */ |
| if (txq->read_ptr == txq->write_ptr && txq->wd_timeout) |
| mod_timer(&txq->stuck_timer, jiffies + txq->wd_timeout); |
| |
| ret = iwl_pcie_set_cmd_in_flight(trans, cmd); |
| if (ret < 0) { |
| idx = ret; |
| goto out; |
| } |
| |
| /* Increment and update queue's write index */ |
| txq->write_ptr = iwl_txq_inc_wrap(trans, txq->write_ptr); |
| iwl_pcie_txq_inc_wr_ptr(trans, txq); |
| |
| out: |
| spin_unlock_irqrestore(&txq->lock, flags); |
| free_dup_buf: |
| if (idx < 0) |
| kfree(dup_buf); |
| return idx; |
| } |
| |
| /* |
| * iwl_pcie_hcmd_complete - Pull unused buffers off the queue and reclaim them |
| * @rxb: Rx buffer to reclaim |
| */ |
| void iwl_pcie_hcmd_complete(struct iwl_trans *trans, |
| struct iwl_rx_cmd_buffer *rxb) |
| { |
| struct iwl_rx_packet *pkt = rxb_addr(rxb); |
| u16 sequence = le16_to_cpu(pkt->hdr.sequence); |
| u8 group_id; |
| u32 cmd_id; |
| int txq_id = SEQ_TO_QUEUE(sequence); |
| int index = SEQ_TO_INDEX(sequence); |
| int cmd_index; |
| struct iwl_device_cmd *cmd; |
| struct iwl_cmd_meta *meta; |
| struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); |
| struct iwl_txq *txq = trans->txqs.txq[trans->txqs.cmd.q_id]; |
| |
| /* If a Tx command is being handled and it isn't in the actual |
| * command queue then there a command routing bug has been introduced |
| * in the queue management code. */ |
| if (WARN(txq_id != trans->txqs.cmd.q_id, |
| "wrong command queue %d (should be %d), sequence 0x%X readp=%d writep=%d\n", |
| txq_id, trans->txqs.cmd.q_id, sequence, txq->read_ptr, |
| txq->write_ptr)) { |
| iwl_print_hex_error(trans, pkt, 32); |
| return; |
| } |
| |
| spin_lock_bh(&txq->lock); |
| |
| cmd_index = iwl_txq_get_cmd_index(txq, index); |
| cmd = txq->entries[cmd_index].cmd; |
| meta = &txq->entries[cmd_index].meta; |
| group_id = cmd->hdr.group_id; |
| cmd_id = iwl_cmd_id(cmd->hdr.cmd, group_id, 0); |
| |
| iwl_txq_gen1_tfd_unmap(trans, meta, txq, index); |
| |
| /* Input error checking is done when commands are added to queue. */ |
| if (meta->flags & CMD_WANT_SKB) { |
| struct page *p = rxb_steal_page(rxb); |
| |
| meta->source->resp_pkt = pkt; |
| meta->source->_rx_page_addr = (unsigned long)page_address(p); |
| meta->source->_rx_page_order = trans_pcie->rx_page_order; |
| } |
| |
| if (meta->flags & CMD_WANT_ASYNC_CALLBACK) |
| iwl_op_mode_async_cb(trans->op_mode, cmd); |
| |
| iwl_pcie_cmdq_reclaim(trans, txq_id, index); |
| |
| if (!(meta->flags & CMD_ASYNC)) { |
| if (!test_bit(STATUS_SYNC_HCMD_ACTIVE, &trans->status)) { |
| IWL_WARN(trans, |
| "HCMD_ACTIVE already clear for command %s\n", |
| iwl_get_cmd_string(trans, cmd_id)); |
| } |
| clear_bit(STATUS_SYNC_HCMD_ACTIVE, &trans->status); |
| IWL_DEBUG_INFO(trans, "Clearing HCMD_ACTIVE for command %s\n", |
| iwl_get_cmd_string(trans, cmd_id)); |
| wake_up(&trans->wait_command_queue); |
| } |
| |
| meta->flags = 0; |
| |
| spin_unlock_bh(&txq->lock); |
| } |
| |
| static int iwl_fill_data_tbs(struct iwl_trans *trans, struct sk_buff *skb, |
| struct iwl_txq *txq, u8 hdr_len, |
| struct iwl_cmd_meta *out_meta) |
| { |
| u16 head_tb_len; |
| int i; |
| |
| /* |
| * Set up TFD's third entry to point directly to remainder |
| * of skb's head, if any |
| */ |
| head_tb_len = skb_headlen(skb) - hdr_len; |
| |
| if (head_tb_len > 0) { |
| dma_addr_t tb_phys = dma_map_single(trans->dev, |
| skb->data + hdr_len, |
| head_tb_len, DMA_TO_DEVICE); |
| if (unlikely(dma_mapping_error(trans->dev, tb_phys))) |
| return -EINVAL; |
| trace_iwlwifi_dev_tx_tb(trans->dev, skb, skb->data + hdr_len, |
| tb_phys, head_tb_len); |
| iwl_pcie_txq_build_tfd(trans, txq, tb_phys, head_tb_len, false); |
| } |
| |
| /* set up the remaining entries to point to the data */ |
| for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { |
| const skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; |
| dma_addr_t tb_phys; |
| int tb_idx; |
| |
| if (!skb_frag_size(frag)) |
| continue; |
| |
| tb_phys = skb_frag_dma_map(trans->dev, frag, 0, |
| skb_frag_size(frag), DMA_TO_DEVICE); |
| |
| if (unlikely(dma_mapping_error(trans->dev, tb_phys))) |
| return -EINVAL; |
| trace_iwlwifi_dev_tx_tb(trans->dev, skb, skb_frag_address(frag), |
| tb_phys, skb_frag_size(frag)); |
| tb_idx = iwl_pcie_txq_build_tfd(trans, txq, tb_phys, |
| skb_frag_size(frag), false); |
| if (tb_idx < 0) |
| return tb_idx; |
| |
| out_meta->tbs |= BIT(tb_idx); |
| } |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_INET |
| static int iwl_fill_data_tbs_amsdu(struct iwl_trans *trans, struct sk_buff *skb, |
| struct iwl_txq *txq, u8 hdr_len, |
| struct iwl_cmd_meta *out_meta, |
| struct iwl_device_tx_cmd *dev_cmd, |
| u16 tb1_len) |
| { |
| struct iwl_tx_cmd *tx_cmd = (void *)dev_cmd->payload; |
| struct ieee80211_hdr *hdr = (void *)skb->data; |
| unsigned int snap_ip_tcp_hdrlen, ip_hdrlen, total_len, hdr_room; |
| unsigned int mss = skb_shinfo(skb)->gso_size; |
| u16 length, iv_len, amsdu_pad; |
| u8 *start_hdr; |
| struct iwl_tso_hdr_page *hdr_page; |
| struct tso_t tso; |
| |
| /* if the packet is protected, then it must be CCMP or GCMP */ |
| BUILD_BUG_ON(IEEE80211_CCMP_HDR_LEN != IEEE80211_GCMP_HDR_LEN); |
| iv_len = ieee80211_has_protected(hdr->frame_control) ? |
| IEEE80211_CCMP_HDR_LEN : 0; |
| |
| trace_iwlwifi_dev_tx(trans->dev, skb, |
| iwl_txq_get_tfd(trans, txq, txq->write_ptr), |
| trans->txqs.tfd.size, |
| &dev_cmd->hdr, IWL_FIRST_TB_SIZE + tb1_len, 0); |
| |
| ip_hdrlen = skb_transport_header(skb) - skb_network_header(skb); |
| snap_ip_tcp_hdrlen = 8 + ip_hdrlen + tcp_hdrlen(skb); |
| total_len = skb->len - snap_ip_tcp_hdrlen - hdr_len - iv_len; |
| amsdu_pad = 0; |
| |
| /* total amount of header we may need for this A-MSDU */ |
| hdr_room = DIV_ROUND_UP(total_len, mss) * |
| (3 + snap_ip_tcp_hdrlen + sizeof(struct ethhdr)) + iv_len; |
| |
| /* Our device supports 9 segments at most, it will fit in 1 page */ |
| hdr_page = get_page_hdr(trans, hdr_room, skb); |
| if (!hdr_page) |
| return -ENOMEM; |
| |
| start_hdr = hdr_page->pos; |
| memcpy(hdr_page->pos, skb->data + hdr_len, iv_len); |
| hdr_page->pos += iv_len; |
| |
| /* |
| * Pull the ieee80211 header + IV to be able to use TSO core, |
| * we will restore it for the tx_status flow. |
| */ |
| skb_pull(skb, hdr_len + iv_len); |
| |
| /* |
| * Remove the length of all the headers that we don't actually |
| * have in the MPDU by themselves, but that we duplicate into |
| * all the different MSDUs inside the A-MSDU. |
| */ |
| le16_add_cpu(&tx_cmd->len, -snap_ip_tcp_hdrlen); |
| |
| tso_start(skb, &tso); |
| |
| while (total_len) { |
| /* this is the data left for this subframe */ |
| unsigned int data_left = |
| min_t(unsigned int, mss, total_len); |
| unsigned int hdr_tb_len; |
| dma_addr_t hdr_tb_phys; |
| u8 *subf_hdrs_start = hdr_page->pos; |
| |
| total_len -= data_left; |
| |
| memset(hdr_page->pos, 0, amsdu_pad); |
| hdr_page->pos += amsdu_pad; |
| amsdu_pad = (4 - (sizeof(struct ethhdr) + snap_ip_tcp_hdrlen + |
| data_left)) & 0x3; |
| ether_addr_copy(hdr_page->pos, ieee80211_get_DA(hdr)); |
| hdr_page->pos += ETH_ALEN; |
| ether_addr_copy(hdr_page->pos, ieee80211_get_SA(hdr)); |
| hdr_page->pos += ETH_ALEN; |
| |
| length = snap_ip_tcp_hdrlen + data_left; |
| *((__be16 *)hdr_page->pos) = cpu_to_be16(length); |
| hdr_page->pos += sizeof(length); |
| |
| /* |
| * This will copy the SNAP as well which will be considered |
| * as MAC header. |
| */ |
| tso_build_hdr(skb, hdr_page->pos, &tso, data_left, !total_len); |
| |
| hdr_page->pos += snap_ip_tcp_hdrlen; |
| |
| hdr_tb_len = hdr_page->pos - start_hdr; |
| hdr_tb_phys = dma_map_single(trans->dev, start_hdr, |
| hdr_tb_len, DMA_TO_DEVICE); |
| if (unlikely(dma_mapping_error(trans->dev, hdr_tb_phys))) |
| return -EINVAL; |
| iwl_pcie_txq_build_tfd(trans, txq, hdr_tb_phys, |
| hdr_tb_len, false); |
| trace_iwlwifi_dev_tx_tb(trans->dev, skb, start_hdr, |
| hdr_tb_phys, hdr_tb_len); |
| /* add this subframe's headers' length to the tx_cmd */ |
| le16_add_cpu(&tx_cmd->len, hdr_page->pos - subf_hdrs_start); |
| |
| /* prepare the start_hdr for the next subframe */ |
| start_hdr = hdr_page->pos; |
| |
| /* put the payload */ |
| while (data_left) { |
| unsigned int size = min_t(unsigned int, tso.size, |
| data_left); |
| dma_addr_t tb_phys; |
| |
| tb_phys = dma_map_single(trans->dev, tso.data, |
| size, DMA_TO_DEVICE); |
| if (unlikely(dma_mapping_error(trans->dev, tb_phys))) |
| return -EINVAL; |
| |
| iwl_pcie_txq_build_tfd(trans, txq, tb_phys, |
| size, false); |
| trace_iwlwifi_dev_tx_tb(trans->dev, skb, tso.data, |
| tb_phys, size); |
| |
| data_left -= size; |
| tso_build_data(skb, &tso, size); |
| } |
| } |
| |
| /* re -add the WiFi header and IV */ |
| skb_push(skb, hdr_len + iv_len); |
| |
| return 0; |
| } |
| #else /* CONFIG_INET */ |
| static int iwl_fill_data_tbs_amsdu(struct iwl_trans *trans, struct sk_buff *skb, |
| struct iwl_txq *txq, u8 hdr_len, |
| struct iwl_cmd_meta *out_meta, |
| struct iwl_device_tx_cmd *dev_cmd, |
| u16 tb1_len) |
| { |
| /* No A-MSDU without CONFIG_INET */ |
| WARN_ON(1); |
| |
| return -1; |
| } |
| #endif /* CONFIG_INET */ |
| |
| int iwl_trans_pcie_tx(struct iwl_trans *trans, struct sk_buff *skb, |
| struct iwl_device_tx_cmd *dev_cmd, int txq_id) |
| { |
| struct ieee80211_hdr *hdr; |
| struct iwl_tx_cmd *tx_cmd = (struct iwl_tx_cmd *)dev_cmd->payload; |
| struct iwl_cmd_meta *out_meta; |
| struct iwl_txq *txq; |
| dma_addr_t tb0_phys, tb1_phys, scratch_phys; |
| void *tb1_addr; |
| void *tfd; |
| u16 len, tb1_len; |
| bool wait_write_ptr; |
| __le16 fc; |
| u8 hdr_len; |
| u16 wifi_seq; |
| bool amsdu; |
| |
| txq = trans->txqs.txq[txq_id]; |
| |
| if (WARN_ONCE(!test_bit(txq_id, trans->txqs.queue_used), |
| "TX on unused queue %d\n", txq_id)) |
| return -EINVAL; |
| |
| if (skb_is_nonlinear(skb) && |
| skb_shinfo(skb)->nr_frags > IWL_TRANS_MAX_FRAGS(trans) && |
| __skb_linearize(skb)) |
| return -ENOMEM; |
| |
| /* mac80211 always puts the full header into the SKB's head, |
| * so there's no need to check if it's readable there |
| */ |
| hdr = (struct ieee80211_hdr *)skb->data; |
| fc = hdr->frame_control; |
| hdr_len = ieee80211_hdrlen(fc); |
| |
| spin_lock(&txq->lock); |
| |
| if (iwl_txq_space(trans, txq) < txq->high_mark) { |
| iwl_txq_stop(trans, txq); |
| |
| /* don't put the packet on the ring, if there is no room */ |
| if (unlikely(iwl_txq_space(trans, txq) < 3)) { |
| struct iwl_device_tx_cmd **dev_cmd_ptr; |
| |
| dev_cmd_ptr = (void *)((u8 *)skb->cb + |
| trans->txqs.dev_cmd_offs); |
| |
| *dev_cmd_ptr = dev_cmd; |
| __skb_queue_tail(&txq->overflow_q, skb); |
| |
| spin_unlock(&txq->lock); |
| return 0; |
| } |
| } |
| |
| /* In AGG mode, the index in the ring must correspond to the WiFi |
| * sequence number. This is a HW requirements to help the SCD to parse |
| * the BA. |
| * Check here that the packets are in the right place on the ring. |
| */ |
| wifi_seq = IEEE80211_SEQ_TO_SN(le16_to_cpu(hdr->seq_ctrl)); |
| WARN_ONCE(txq->ampdu && |
| (wifi_seq & 0xff) != txq->write_ptr, |
| "Q: %d WiFi Seq %d tfdNum %d", |
| txq_id, wifi_seq, txq->write_ptr); |
| |
| /* Set up driver data for this TFD */ |
| txq->entries[txq->write_ptr].skb = skb; |
| txq->entries[txq->write_ptr].cmd = dev_cmd; |
| |
| dev_cmd->hdr.sequence = |
| cpu_to_le16((u16)(QUEUE_TO_SEQ(txq_id) | |
| INDEX_TO_SEQ(txq->write_ptr))); |
| |
| tb0_phys = iwl_txq_get_first_tb_dma(txq, txq->write_ptr); |
| scratch_phys = tb0_phys + sizeof(struct iwl_cmd_header) + |
| offsetof(struct iwl_tx_cmd, scratch); |
| |
| tx_cmd->dram_lsb_ptr = cpu_to_le32(scratch_phys); |
| tx_cmd->dram_msb_ptr = iwl_get_dma_hi_addr(scratch_phys); |
| |
| /* Set up first empty entry in queue's array of Tx/cmd buffers */ |
| out_meta = &txq->entries[txq->write_ptr].meta; |
| out_meta->flags = 0; |
| |
| /* |
| * The second TB (tb1) points to the remainder of the TX command |
| * and the 802.11 header - dword aligned size |
| * (This calculation modifies the TX command, so do it before the |
| * setup of the first TB) |
| */ |
| len = sizeof(struct iwl_tx_cmd) + sizeof(struct iwl_cmd_header) + |
| hdr_len - IWL_FIRST_TB_SIZE; |
| /* do not align A-MSDU to dword as the subframe header aligns it */ |
| amsdu = ieee80211_is_data_qos(fc) && |
| (*ieee80211_get_qos_ctl(hdr) & |
| IEEE80211_QOS_CTL_A_MSDU_PRESENT); |
| if (!amsdu) { |
| tb1_len = ALIGN(len, 4); |
| /* Tell NIC about any 2-byte padding after MAC header */ |
| if (tb1_len != len) |
| tx_cmd->tx_flags |= cpu_to_le32(TX_CMD_FLG_MH_PAD); |
| } else { |
| tb1_len = len; |
| } |
| |
| /* |
| * The first TB points to bi-directional DMA data, we'll |
| * memcpy the data into it later. |
| */ |
| iwl_pcie_txq_build_tfd(trans, txq, tb0_phys, |
| IWL_FIRST_TB_SIZE, true); |
| |
| /* there must be data left over for TB1 or this code must be changed */ |
| BUILD_BUG_ON(sizeof(struct iwl_tx_cmd) < IWL_FIRST_TB_SIZE); |
| |
| /* map the data for TB1 */ |
| tb1_addr = ((u8 *)&dev_cmd->hdr) + IWL_FIRST_TB_SIZE; |
| tb1_phys = dma_map_single(trans->dev, tb1_addr, tb1_len, DMA_TO_DEVICE); |
| if (unlikely(dma_mapping_error(trans->dev, tb1_phys))) |
| goto out_err; |
| iwl_pcie_txq_build_tfd(trans, txq, tb1_phys, tb1_len, false); |
| |
| trace_iwlwifi_dev_tx(trans->dev, skb, |
| iwl_txq_get_tfd(trans, txq, txq->write_ptr), |
| trans->txqs.tfd.size, |
| &dev_cmd->hdr, IWL_FIRST_TB_SIZE + tb1_len, |
| hdr_len); |
| |
| /* |
| * If gso_size wasn't set, don't give the frame "amsdu treatment" |
| * (adding subframes, etc.). |
| * This can happen in some testing flows when the amsdu was already |
| * pre-built, and we just need to send the resulting skb. |
| */ |
| if (amsdu && skb_shinfo(skb)->gso_size) { |
| if (unlikely(iwl_fill_data_tbs_amsdu(trans, skb, txq, hdr_len, |
| out_meta, dev_cmd, |
| tb1_len))) |
| goto out_err; |
| } else { |
| struct sk_buff *frag; |
| |
| if (unlikely(iwl_fill_data_tbs(trans, skb, txq, hdr_len, |
| out_meta))) |
| goto out_err; |
| |
| skb_walk_frags(skb, frag) { |
| if (unlikely(iwl_fill_data_tbs(trans, frag, txq, 0, |
| out_meta))) |
| goto out_err; |
| } |
| } |
| |
| /* building the A-MSDU might have changed this data, so memcpy it now */ |
| memcpy(&txq->first_tb_bufs[txq->write_ptr], dev_cmd, IWL_FIRST_TB_SIZE); |
| |
| tfd = iwl_txq_get_tfd(trans, txq, txq->write_ptr); |
| /* Set up entry for this TFD in Tx byte-count array */ |
| iwl_txq_gen1_update_byte_cnt_tbl(trans, txq, le16_to_cpu(tx_cmd->len), |
| iwl_txq_gen1_tfd_get_num_tbs(trans, |
| tfd)); |
| |
| wait_write_ptr = ieee80211_has_morefrags(fc); |
| |
| /* start timer if queue currently empty */ |
| if (txq->read_ptr == txq->write_ptr && txq->wd_timeout) { |
| /* |
| * If the TXQ is active, then set the timer, if not, |
| * set the timer in remainder so that the timer will |
| * be armed with the right value when the station will |
| * wake up. |
| */ |
| if (!txq->frozen) |
| mod_timer(&txq->stuck_timer, |
| jiffies + txq->wd_timeout); |
| else |
| txq->frozen_expiry_remainder = txq->wd_timeout; |
| } |
| |
| /* Tell device the write index *just past* this latest filled TFD */ |
| txq->write_ptr = iwl_txq_inc_wrap(trans, txq->write_ptr); |
| if (!wait_write_ptr) |
| iwl_pcie_txq_inc_wr_ptr(trans, txq); |
| |
| /* |
| * At this point the frame is "transmitted" successfully |
| * and we will get a TX status notification eventually. |
| */ |
| spin_unlock(&txq->lock); |
| return 0; |
| out_err: |
| iwl_txq_gen1_tfd_unmap(trans, out_meta, txq, txq->write_ptr); |
| spin_unlock(&txq->lock); |
| return -1; |
| } |