drivers/regulator/bd71815-regulator.c - linux - Git at Google

 // SPDX-License-Identifier: GPL-2.0-only
 //
 // Copyright 2014 Embest Technology Co. Ltd. Inc.
 // bd71815-regulator.c ROHM BD71815 regulator driver
 //
 // Author: Tony Luo <luofc@embedinfo.com>
 //
 // Partially rewritten at 2021 by
 // Matti Vaittinen <matti.vaitinen@fi.rohmeurope.com>

 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/err.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
 #include <linux/gpio/consumer.h>
 #include <linux/regulator/driver.h>
 #include <linux/delay.h>
 #include <linux/slab.h>
 #include <linux/gpio.h>
 #include <linux/mfd/rohm-generic.h>
 #include <linux/mfd/rohm-bd71815.h>
 #include <linux/regulator/of_regulator.h>

 struct bd71815_regulator {
 	struct regulator_desc desc;
 	const struct rohm_dvs_config *dvs;
 };

 static const int bd7181x_wled_currents[] = {
 	10, 20, 30, 50, 70, 100, 200, 300, 500, 700, 1000, 2000, 3000, 4000,
 	5000, 6000, 7000, 8000, 9000, 10000, 11000, 12000, 13000, 14000, 15000,
 	16000, 17000, 18000, 19000, 20000, 21000, 22000, 23000, 24000, 25000,
 };

 static const struct rohm_dvs_config buck1_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_reg		= BD71815_REG_BUCK1_VOLT_H,
 	.run_mask		= BD71815_VOLT_MASK,
 	.run_on_mask		= BD71815_BUCK_RUN_ON,
 	.snvs_on_mask		= BD71815_BUCK_SNVS_ON,
 	.suspend_reg		= BD71815_REG_BUCK1_VOLT_L,
 	.suspend_mask		= BD71815_VOLT_MASK,
 	.suspend_on_mask	= BD71815_BUCK_SUSP_ON,
 	.lpsr_reg		= BD71815_REG_BUCK1_VOLT_L,
 	.lpsr_mask		= BD71815_VOLT_MASK,
 	.lpsr_on_mask		= BD71815_BUCK_LPSR_ON,
 };

 static const struct rohm_dvs_config buck2_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_reg		= BD71815_REG_BUCK2_VOLT_H,
 	.run_mask		= BD71815_VOLT_MASK,
 	.run_on_mask		= BD71815_BUCK_RUN_ON,
 	.snvs_on_mask		= BD71815_BUCK_SNVS_ON,
 	.suspend_reg		= BD71815_REG_BUCK2_VOLT_L,
 	.suspend_mask		= BD71815_VOLT_MASK,
 	.suspend_on_mask	= BD71815_BUCK_SUSP_ON,
 	.lpsr_reg		= BD71815_REG_BUCK2_VOLT_L,
 	.lpsr_mask		= BD71815_VOLT_MASK,
 	.lpsr_on_mask		= BD71815_BUCK_LPSR_ON,
 };

 static const struct rohm_dvs_config buck3_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_reg		= BD71815_REG_BUCK3_VOLT,
 	.run_mask		= BD71815_VOLT_MASK,
 	.run_on_mask		= BD71815_BUCK_RUN_ON,
 	.snvs_on_mask		= BD71815_BUCK_SNVS_ON,
 	.suspend_on_mask	= BD71815_BUCK_SUSP_ON,
 	.lpsr_on_mask		= BD71815_BUCK_LPSR_ON,
 };

 static const struct rohm_dvs_config buck4_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_reg		= BD71815_REG_BUCK4_VOLT,
 	.run_mask		= BD71815_VOLT_MASK,
 	.run_on_mask		= BD71815_BUCK_RUN_ON,
 	.snvs_on_mask		= BD71815_BUCK_SNVS_ON,
 	.suspend_on_mask	= BD71815_BUCK_SUSP_ON,
 	.lpsr_on_mask		= BD71815_BUCK_LPSR_ON,
 };

 static const struct rohm_dvs_config ldo1_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_reg		= BD71815_REG_LDO_MODE1,
 	.run_mask		= BD71815_VOLT_MASK,
 	.run_on_mask		= LDO1_RUN_ON,
 	.snvs_on_mask		= LDO1_SNVS_ON,
 	.suspend_on_mask	= LDO1_SUSP_ON,
 	.lpsr_on_mask		= LDO1_LPSR_ON,
 };

 static const struct rohm_dvs_config ldo2_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_reg		= BD71815_REG_LDO_MODE2,
 	.run_mask		= BD71815_VOLT_MASK,
 	.run_on_mask		= LDO2_RUN_ON,
 	.snvs_on_mask		= LDO2_SNVS_ON,
 	.suspend_on_mask	= LDO2_SUSP_ON,
 	.lpsr_on_mask		= LDO2_LPSR_ON,
 };

 static const struct rohm_dvs_config ldo3_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_reg		= BD71815_REG_LDO_MODE2,
 	.run_mask		= BD71815_VOLT_MASK,
 	.run_on_mask		= LDO3_RUN_ON,
 	.snvs_on_mask		= LDO3_SNVS_ON,
 	.suspend_on_mask	= LDO3_SUSP_ON,
 	.lpsr_on_mask		= LDO3_LPSR_ON,
 };

 static const struct rohm_dvs_config ldo4_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_reg		= BD71815_REG_LDO_MODE3,
 	.run_mask		= BD71815_VOLT_MASK,
 	.run_on_mask		= LDO4_RUN_ON,
 	.snvs_on_mask		= LDO4_SNVS_ON,
 	.suspend_on_mask	= LDO4_SUSP_ON,
 	.lpsr_on_mask		= LDO4_LPSR_ON,
 };

 static const struct rohm_dvs_config ldo5_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_reg		= BD71815_REG_LDO_MODE3,
 	.run_mask		= BD71815_VOLT_MASK,
 	.run_on_mask		= LDO5_RUN_ON,
 	.snvs_on_mask		= LDO5_SNVS_ON,
 	.suspend_on_mask	= LDO5_SUSP_ON,
 	.lpsr_on_mask		= LDO5_LPSR_ON,
 };

 static const struct rohm_dvs_config dvref_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_on_mask		= DVREF_RUN_ON,
 	.snvs_on_mask		= DVREF_SNVS_ON,
 	.suspend_on_mask	= DVREF_SUSP_ON,
 	.lpsr_on_mask		= DVREF_LPSR_ON,
 };

 static const struct rohm_dvs_config ldolpsr_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_on_mask		= DVREF_RUN_ON,
 	.snvs_on_mask		= DVREF_SNVS_ON,
 	.suspend_on_mask	= DVREF_SUSP_ON,
 	.lpsr_on_mask		= DVREF_LPSR_ON,
 };

 static const struct rohm_dvs_config buck5_dvs = {
 	.level_map		= ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
 				  ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
 	.run_reg		= BD71815_REG_BUCK5_VOLT,
 	.run_mask		= BD71815_VOLT_MASK,
 	.run_on_mask		= BD71815_BUCK_RUN_ON,
 	.snvs_on_mask		= BD71815_BUCK_SNVS_ON,
 	.suspend_on_mask	= BD71815_BUCK_SUSP_ON,
 	.lpsr_on_mask		= BD71815_BUCK_LPSR_ON,
 };

 static int set_hw_dvs_levels(struct device_node *np,
 			     const struct regulator_desc *desc,
 			     struct regulator_config *cfg)
 {
 	struct bd71815_regulator *data;

 	data = container_of(desc, struct bd71815_regulator, desc);
 	return rohm_regulator_set_dvs_levels(data->dvs, np, desc, cfg->regmap);
 }

 /*
  * Bucks 1 and 2 have two voltage selection registers where selected
  * voltage can be set. Which of the registers is used can be either controlled
  * by a control bit in register - or by HW state. If HW state specific voltages
  * are given - then we assume HW state based control should be used.
  *
  * If volatge value is updated to currently selected register - then output
  * voltage is immediately changed no matter what is set as ramp rate. Thus we
  * default changing voltage by writing new value to inactive register and
  * then updating the 'register selection' bit. This naturally only works when
  * HW state machine is not used to select the voltage.
  */
 static int buck12_set_hw_dvs_levels(struct device_node *np,
 				    const struct regulator_desc *desc,
 				    struct regulator_config *cfg)
 {
 	struct bd71815_regulator *data;
 	int ret = 0, val;

 	data = container_of(desc, struct bd71815_regulator, desc);

 	if (of_find_property(np, "rohm,dvs-run-voltage", NULL) ||
 	    of_find_property(np, "rohm,dvs-suspend-voltage", NULL) ||
 	    of_find_property(np, "rohm,dvs-lpsr-voltage", NULL) ||
 	    of_find_property(np, "rohm,dvs-snvs-voltage", NULL)) {
 		ret = regmap_read(cfg->regmap, desc->vsel_reg, &val);
 		if (ret)
 			return ret;

 		if (!(BD71815_BUCK_STBY_DVS & val) &&
 		    !(BD71815_BUCK_DVSSEL & val)) {
 			int val2;

 			/*
 			 * We are currently using voltage from _L.
 			 * We'd better copy it to _H and switch to it to
 			 * avoid shutting us down if LPSR or SUSPEND is set to
 			 * disabled. _L value is at reg _H + 1
 			 */
 			ret = regmap_read(cfg->regmap, desc->vsel_reg + 1,
 					  &val2);
 			if (ret)
 				return ret;

 			ret = regmap_update_bits(cfg->regmap, desc->vsel_reg,
 						 BD71815_VOLT_MASK |
 						 BD71815_BUCK_DVSSEL,
 						 val2 | BD71815_BUCK_DVSSEL);
 			if (ret)
 				return ret;
 		}
 		ret = rohm_regulator_set_dvs_levels(data->dvs, np, desc,
 						    cfg->regmap);
 		if (ret)
 			return ret;
 		/*
 		 * DVS levels were given => use HW-state machine for voltage
 		 * controls. NOTE: AFAIK, This means that if voltage is changed
 		 * by SW the ramp-rate is not respected. Should we disable
 		 * SW voltage control when the HW state machine is used?
 		 */
 		ret = regmap_update_bits(cfg->regmap, desc->vsel_reg,
 					 BD71815_BUCK_STBY_DVS,
 					 BD71815_BUCK_STBY_DVS);
 	}

 	return ret;
 }

 /*
  * BUCK1/2
  * BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
  * 00: 10.00mV/usec	10mV 1uS
  * 01: 5.00mV/usec	10mV 2uS
  * 10: 2.50mV/usec	10mV 4uS
  * 11: 1.25mV/usec	10mV 8uS
  */
 static const unsigned int bd7181x_ramp_table[] = { 1250, 2500, 5000, 10000 };

 static int bd7181x_led_set_current_limit(struct regulator_dev *rdev,
 					int min_uA, int max_uA)
 {
 	int ret;
 	int onstatus;

 	onstatus = regulator_is_enabled_regmap(rdev);

 	ret = regulator_set_current_limit_regmap(rdev, min_uA, max_uA);
 	if (!ret) {
 		int newstatus;

 		newstatus = regulator_is_enabled_regmap(rdev);
 		if (onstatus != newstatus) {
 			/*
 			 * HW FIX: spurious led status change detected. Toggle
 			 * state as a workaround
 			 */
 			if (onstatus)
 				ret = regulator_enable_regmap(rdev);
 			else
 				ret = regulator_disable_regmap(rdev);

 			if (ret)
 				dev_err(rdev_get_dev(rdev),
 					"failed to revert the LED state (%d)\n",
 					ret);
 		}
 	}

 	return ret;
 }

 static int bd7181x_buck12_get_voltage_sel(struct regulator_dev *rdev)
 {
 	int rid = rdev_get_id(rdev);
 	int ret, regh, regl, val;

 	regh = BD71815_REG_BUCK1_VOLT_H + rid * 0x2;
 	regl = BD71815_REG_BUCK1_VOLT_L + rid * 0x2;

 	ret = regmap_read(rdev->regmap, regh, &val);
 	if (ret)
 		return ret;

 	/*
 	 * If we use HW state machine based voltage reg selection - then we
 	 * return BD71815_REG_BUCK1_VOLT_H which is used at RUN.
 	 * Else we do return the BD71815_REG_BUCK1_VOLT_H or
 	 * BD71815_REG_BUCK1_VOLT_L depending on which is selected to be used
 	 * by BD71815_BUCK_DVSSEL bit
 	 */
 	if ((!(val & BD71815_BUCK_STBY_DVS)) && (!(val & BD71815_BUCK_DVSSEL)))
 		ret = regmap_read(rdev->regmap, regl, &val);

 	if (ret)
 		return ret;

 	return val & BD71815_VOLT_MASK;
 }

 /*
  * For Buck 1/2.
  */
 static int bd7181x_buck12_set_voltage_sel(struct regulator_dev *rdev,
 					  unsigned int sel)
 {
 	int rid = rdev_get_id(rdev);
 	int ret, val, reg, regh, regl;

 	regh = BD71815_REG_BUCK1_VOLT_H + rid*0x2;
 	regl = BD71815_REG_BUCK1_VOLT_L + rid*0x2;

 	ret = regmap_read(rdev->regmap, regh, &val);
 	if (ret)
 		return ret;

 	/*
 	 * If bucks 1 & 2 are controlled by state machine - then the RUN state
 	 * voltage is set to BD71815_REG_BUCK1_VOLT_H. Changing SUSPEND/LPSR
 	 * voltages at runtime is not supported by this driver.
 	 */
 	if (((val & BD71815_BUCK_STBY_DVS))) {
 		return regmap_update_bits(rdev->regmap, regh, BD71815_VOLT_MASK,
 					  sel);
 	}
 	/* Update new voltage to the register which is not selected now */
 	if (val & BD71815_BUCK_DVSSEL)
 		reg = regl;
 	else
 		reg = regh;

 	ret = regmap_update_bits(rdev->regmap, reg, BD71815_VOLT_MASK, sel);
 	if (ret)
 		return ret;

 	/* Select the other DVS register to be used */
 	return regmap_update_bits(rdev->regmap, regh, BD71815_BUCK_DVSSEL,
 				  ~val);
 }

 static const struct regulator_ops bd7181x_ldo_regulator_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
 	.list_voltage = regulator_list_voltage_linear,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 };

 static const struct regulator_ops bd7181x_fixed_regulator_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
 	.list_voltage = regulator_list_voltage_linear,
 };

 static const struct regulator_ops bd7181x_buck_regulator_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
 	.list_voltage = regulator_list_voltage_linear,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
 };

 static const struct regulator_ops bd7181x_buck12_regulator_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
 	.list_voltage = regulator_list_voltage_linear,
 	.set_voltage_sel = bd7181x_buck12_set_voltage_sel,
 	.get_voltage_sel = bd7181x_buck12_get_voltage_sel,
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
 	.set_ramp_delay = regulator_set_ramp_delay_regmap,
 };

 static const struct regulator_ops bd7181x_led_regulator_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
 	.set_current_limit = bd7181x_led_set_current_limit,
 	.get_current_limit = regulator_get_current_limit_regmap,
 };

 #define BD71815_FIXED_REG(_name, _id, ereg, emsk, voltage, _dvs)	\
 	[(_id)] = {							\
 		.desc = {						\
 			.name = #_name,					\
 			.of_match = of_match_ptr(#_name),		\
 			.regulators_node = of_match_ptr("regulators"),	\
 			.n_voltages = 1,				\
 			.ops = &bd7181x_fixed_regulator_ops,		\
 			.type = REGULATOR_VOLTAGE,			\
 			.id = (_id),					\
 			.owner = THIS_MODULE,				\
 			.min_uV = (voltage),				\
 			.enable_reg = (ereg),				\
 			.enable_mask = (emsk),				\
 			.of_parse_cb = set_hw_dvs_levels,		\
 		},							\
 		.dvs = (_dvs),						\
 	}

 #define BD71815_BUCK_REG(_name, _id, vsel, ereg, min, max, step, _dvs)	\
 	[(_id)] = {							\
 		.desc = {						\
 			.name = #_name,					\
 			.of_match = of_match_ptr(#_name),		\
 			.regulators_node = of_match_ptr("regulators"),	\
 			.n_voltages = ((max) - (min)) / (step) + 1,	\
 			.ops = &bd7181x_buck_regulator_ops,		\
 			.type = REGULATOR_VOLTAGE,			\
 			.id = (_id),					\
 			.owner = THIS_MODULE,				\
 			.min_uV = (min),				\
 			.uV_step = (step),				\
 			.vsel_reg = (vsel),				\
 			.vsel_mask = BD71815_VOLT_MASK,			\
 			.enable_reg = (ereg),				\
 			.enable_mask = BD71815_BUCK_RUN_ON,		\
 			.of_parse_cb = set_hw_dvs_levels,		\
 		},							\
 		.dvs = (_dvs),						\
 	}

 #define BD71815_BUCK12_REG(_name, _id, vsel, ereg, min, max, step,	\
 			   _dvs)					\
 	[(_id)] = {							\
 		.desc = {						\
 			.name = #_name,					\
 			.of_match = of_match_ptr(#_name),		\
 			.regulators_node = of_match_ptr("regulators"),	\
 			.n_voltages = ((max) - (min)) / (step) + 1,	\
 			.ops = &bd7181x_buck12_regulator_ops,		\
 			.type = REGULATOR_VOLTAGE,			\
 			.id = (_id),					\
 			.owner = THIS_MODULE,				\
 			.min_uV = (min),				\
 			.uV_step = (step),				\
 			.vsel_reg = (vsel),				\
 			.vsel_mask = BD71815_VOLT_MASK,			\
 			.enable_reg = (ereg),				\
 			.enable_mask = BD71815_BUCK_RUN_ON,		\
 			.ramp_reg = (ereg),				\
 			.ramp_mask = BD71815_BUCK_RAMPRATE_MASK,	\
 			.ramp_delay_table = bd7181x_ramp_table,		\
 			.n_ramp_values = ARRAY_SIZE(bd7181x_ramp_table),\
 			.of_parse_cb = buck12_set_hw_dvs_levels,	\
 		},							\
 		.dvs = (_dvs),						\
 	}

 #define BD71815_LED_REG(_name, _id, csel, mask, ereg, emsk, currents)	\
 	[(_id)] = {							\
 		.desc = {						\
 			.name = #_name,					\
 			.of_match = of_match_ptr(#_name),		\
 			.regulators_node = of_match_ptr("regulators"),	\
 			.n_current_limits = ARRAY_SIZE(currents),	\
 			.ops = &bd7181x_led_regulator_ops,		\
 			.type = REGULATOR_CURRENT,			\
 			.id = (_id),					\
 			.owner = THIS_MODULE,				\
 			.curr_table = currents,				\
 			.csel_reg = (csel),				\
 			.csel_mask = (mask),				\
 			.enable_reg = (ereg),				\
 			.enable_mask = (emsk),				\
 		},							\
 	}

 #define BD71815_LDO_REG(_name, _id, vsel, ereg, emsk, min, max, step,	\
 			_dvs)						\
 	[(_id)] = {							\
 		.desc = {						\
 			.name = #_name,					\
 			.of_match = of_match_ptr(#_name),		\
 			.regulators_node = of_match_ptr("regulators"),	\
 			.n_voltages = ((max) - (min)) / (step) + 1,	\
 			.ops = &bd7181x_ldo_regulator_ops,		\
 			.type = REGULATOR_VOLTAGE,			\
 			.id = (_id),					\
 			.owner = THIS_MODULE,				\
 			.min_uV = (min),				\
 			.uV_step = (step),				\
 			.vsel_reg = (vsel),				\
 			.vsel_mask = BD71815_VOLT_MASK,			\
 			.enable_reg = (ereg),				\
 			.enable_mask = (emsk),				\
 			.of_parse_cb = set_hw_dvs_levels,		\
 		},							\
 		.dvs = (_dvs),						\
 	}

 static const struct bd71815_regulator bd71815_regulators[] = {
 	BD71815_BUCK12_REG(buck1, BD71815_BUCK1, BD71815_REG_BUCK1_VOLT_H,
 			   BD71815_REG_BUCK1_MODE, 800000, 2000000, 25000,
 			   &buck1_dvs),
 	BD71815_BUCK12_REG(buck2, BD71815_BUCK2, BD71815_REG_BUCK2_VOLT_H,
 			   BD71815_REG_BUCK2_MODE, 800000, 2000000, 25000,
 			   &buck2_dvs),
 	BD71815_BUCK_REG(buck3, BD71815_BUCK3, BD71815_REG_BUCK3_VOLT,
 			 BD71815_REG_BUCK3_MODE,  1200000, 2700000, 50000,
 			 &buck3_dvs),
 	BD71815_BUCK_REG(buck4, BD71815_BUCK4, BD71815_REG_BUCK4_VOLT,
 			 BD71815_REG_BUCK4_MODE,  1100000, 1850000, 25000,
 			 &buck4_dvs),
 	BD71815_BUCK_REG(buck5, BD71815_BUCK5, BD71815_REG_BUCK5_VOLT,
 			 BD71815_REG_BUCK5_MODE,  1800000, 3300000, 50000,
 			 &buck5_dvs),
 	BD71815_LDO_REG(ldo1, BD71815_LDO1, BD71815_REG_LDO1_VOLT,
 			BD71815_REG_LDO_MODE1, LDO1_RUN_ON, 800000, 3300000,
 			50000, &ldo1_dvs),
 	BD71815_LDO_REG(ldo2, BD71815_LDO2, BD71815_REG_LDO2_VOLT,
 			BD71815_REG_LDO_MODE2, LDO2_RUN_ON, 800000, 3300000,
 			50000, &ldo2_dvs),
 	/*
 	 * Let's default LDO3 to be enabled by SW. We can override ops if DT
 	 * says LDO3 should be enabled by HW when DCIN is connected.
 	 */
 	BD71815_LDO_REG(ldo3, BD71815_LDO3, BD71815_REG_LDO3_VOLT,
 			BD71815_REG_LDO_MODE2, LDO3_RUN_ON, 800000, 3300000,
 			50000, &ldo3_dvs),
 	BD71815_LDO_REG(ldo4, BD71815_LDO4, BD71815_REG_LDO4_VOLT,
 			BD71815_REG_LDO_MODE3, LDO4_RUN_ON, 800000, 3300000,
 			50000, &ldo4_dvs),
 	BD71815_LDO_REG(ldo5, BD71815_LDO5, BD71815_REG_LDO5_VOLT_H,
 			BD71815_REG_LDO_MODE3, LDO5_RUN_ON, 800000, 3300000,
 			50000, &ldo5_dvs),
 	BD71815_FIXED_REG(ldodvref, BD71815_LDODVREF, BD71815_REG_LDO_MODE4,
 			  DVREF_RUN_ON, 3000000, &dvref_dvs),
 	BD71815_FIXED_REG(ldolpsr, BD71815_LDOLPSR, BD71815_REG_LDO_MODE4,
 			  LDO_LPSR_RUN_ON, 1800000, &ldolpsr_dvs),
 	BD71815_LED_REG(wled, BD71815_WLED, BD71815_REG_LED_DIMM, LED_DIMM_MASK,
 			BD71815_REG_LED_CTRL, LED_RUN_ON,
 			bd7181x_wled_currents),
 };

 static int bd7181x_probe(struct platform_device *pdev)
 {
 	struct regulator_config config = {};
 	int i, ret;
 	struct gpio_desc *ldo4_en;
 	struct regmap *regmap;

 	regmap = dev_get_regmap(pdev->dev.parent, NULL);
 	if (!regmap) {
 		dev_err(&pdev->dev, "No parent regmap\n");
 		return -ENODEV;
 	}
 	ldo4_en = devm_gpiod_get_from_of_node(&pdev->dev,
 					      pdev->dev.parent->of_node,
 						 "rohm,vsel-gpios", 0,
 						 GPIOD_ASIS, "ldo4-en");

 	if (IS_ERR(ldo4_en)) {
 		ret = PTR_ERR(ldo4_en);
 		if (ret != -ENOENT)
 			return ret;
 		ldo4_en = NULL;
 	}

 	/* Disable to go to ship-mode */
 	ret = regmap_update_bits(regmap, BD71815_REG_PWRCTRL, RESTARTEN, 0);
 	if (ret)
 		return ret;

 	config.dev = pdev->dev.parent;
 	config.regmap = regmap;

 	for (i = 0; i < BD71815_REGULATOR_CNT; i++) {
 		const struct regulator_desc *desc;
 		struct regulator_dev *rdev;

 		desc = &bd71815_regulators[i].desc;

 		if (i == BD71815_LDO4)
 			config.ena_gpiod = ldo4_en;
 		else
 			config.ena_gpiod = NULL;

 		rdev = devm_regulator_register(&pdev->dev, desc, &config);
 		if (IS_ERR(rdev)) {
 			dev_err(&pdev->dev,
 				"failed to register %s regulator\n",
 				desc->name);
 			return PTR_ERR(rdev);
 		}
 	}
 	return 0;
 }

 static const struct platform_device_id bd7181x_pmic_id[] = {
 	{ "bd71815-pmic", ROHM_CHIP_TYPE_BD71815 },
 	{ },
 };
 MODULE_DEVICE_TABLE(platform, bd7181x_pmic_id);

 static struct platform_driver bd7181x_regulator = {
 	.driver = {
 		.name = "bd7181x-pmic",
 	},
 	.probe = bd7181x_probe,
 	.id_table = bd7181x_pmic_id,
 };
 module_platform_driver(bd7181x_regulator);

 MODULE_AUTHOR("Tony Luo <luofc@embedinfo.com>");
 MODULE_DESCRIPTION("BD71815 voltage regulator driver");
 MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("platform:bd7181x-pmic");
	// SPDX-License-Identifier: GPL-2.0-only
	//
	// Copyright 2014 Embest Technology Co. Ltd. Inc.
	// bd71815-regulator.c ROHM BD71815 regulator driver
	//
	// Author: Tony Luo <luofc@embedinfo.com>
	//
	// Partially rewritten at 2021 by
	// Matti Vaittinen <matti.vaitinen@fi.rohmeurope.com>

	#include <linux/kernel.h>
	#include <linux/module.h>
	#include <linux/init.h>
	#include <linux/err.h>
	#include <linux/platform_device.h>
	#include <linux/of.h>
	#include <linux/gpio/consumer.h>
	#include <linux/regulator/driver.h>
	#include <linux/delay.h>
	#include <linux/slab.h>
	#include <linux/gpio.h>
	#include <linux/mfd/rohm-generic.h>
	#include <linux/mfd/rohm-bd71815.h>
	#include <linux/regulator/of_regulator.h>

	struct bd71815_regulator {
	struct regulator_desc desc;
	const struct rohm_dvs_config *dvs;
	};

	static const int bd7181x_wled_currents[] = {
	10, 20, 30, 50, 70, 100, 200, 300, 500, 700, 1000, 2000, 3000, 4000,
	5000, 6000, 7000, 8000, 9000, 10000, 11000, 12000, 13000, 14000, 15000,
	16000, 17000, 18000, 19000, 20000, 21000, 22000, 23000, 24000, 25000,
	};

	static const struct rohm_dvs_config buck1_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_reg = BD71815_REG_BUCK1_VOLT_H,
	.run_mask = BD71815_VOLT_MASK,
	.run_on_mask = BD71815_BUCK_RUN_ON,
	.snvs_on_mask = BD71815_BUCK_SNVS_ON,
	.suspend_reg = BD71815_REG_BUCK1_VOLT_L,
	.suspend_mask = BD71815_VOLT_MASK,
	.suspend_on_mask = BD71815_BUCK_SUSP_ON,
	.lpsr_reg = BD71815_REG_BUCK1_VOLT_L,
	.lpsr_mask = BD71815_VOLT_MASK,
	.lpsr_on_mask = BD71815_BUCK_LPSR_ON,
	};

	static const struct rohm_dvs_config buck2_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_reg = BD71815_REG_BUCK2_VOLT_H,
	.run_mask = BD71815_VOLT_MASK,
	.run_on_mask = BD71815_BUCK_RUN_ON,
	.snvs_on_mask = BD71815_BUCK_SNVS_ON,
	.suspend_reg = BD71815_REG_BUCK2_VOLT_L,
	.suspend_mask = BD71815_VOLT_MASK,
	.suspend_on_mask = BD71815_BUCK_SUSP_ON,
	.lpsr_reg = BD71815_REG_BUCK2_VOLT_L,
	.lpsr_mask = BD71815_VOLT_MASK,
	.lpsr_on_mask = BD71815_BUCK_LPSR_ON,
	};

	static const struct rohm_dvs_config buck3_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_reg = BD71815_REG_BUCK3_VOLT,
	.run_mask = BD71815_VOLT_MASK,
	.run_on_mask = BD71815_BUCK_RUN_ON,
	.snvs_on_mask = BD71815_BUCK_SNVS_ON,
	.suspend_on_mask = BD71815_BUCK_SUSP_ON,
	.lpsr_on_mask = BD71815_BUCK_LPSR_ON,
	};

	static const struct rohm_dvs_config buck4_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_reg = BD71815_REG_BUCK4_VOLT,
	.run_mask = BD71815_VOLT_MASK,
	.run_on_mask = BD71815_BUCK_RUN_ON,
	.snvs_on_mask = BD71815_BUCK_SNVS_ON,
	.suspend_on_mask = BD71815_BUCK_SUSP_ON,
	.lpsr_on_mask = BD71815_BUCK_LPSR_ON,
	};

	static const struct rohm_dvs_config ldo1_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_reg = BD71815_REG_LDO_MODE1,
	.run_mask = BD71815_VOLT_MASK,
	.run_on_mask = LDO1_RUN_ON,
	.snvs_on_mask = LDO1_SNVS_ON,
	.suspend_on_mask = LDO1_SUSP_ON,
	.lpsr_on_mask = LDO1_LPSR_ON,
	};

	static const struct rohm_dvs_config ldo2_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_reg = BD71815_REG_LDO_MODE2,
	.run_mask = BD71815_VOLT_MASK,
	.run_on_mask = LDO2_RUN_ON,
	.snvs_on_mask = LDO2_SNVS_ON,
	.suspend_on_mask = LDO2_SUSP_ON,
	.lpsr_on_mask = LDO2_LPSR_ON,
	};

	static const struct rohm_dvs_config ldo3_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_reg = BD71815_REG_LDO_MODE2,
	.run_mask = BD71815_VOLT_MASK,
	.run_on_mask = LDO3_RUN_ON,
	.snvs_on_mask = LDO3_SNVS_ON,
	.suspend_on_mask = LDO3_SUSP_ON,
	.lpsr_on_mask = LDO3_LPSR_ON,
	};

	static const struct rohm_dvs_config ldo4_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_reg = BD71815_REG_LDO_MODE3,
	.run_mask = BD71815_VOLT_MASK,
	.run_on_mask = LDO4_RUN_ON,
	.snvs_on_mask = LDO4_SNVS_ON,
	.suspend_on_mask = LDO4_SUSP_ON,
	.lpsr_on_mask = LDO4_LPSR_ON,
	};

	static const struct rohm_dvs_config ldo5_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_reg = BD71815_REG_LDO_MODE3,
	.run_mask = BD71815_VOLT_MASK,
	.run_on_mask = LDO5_RUN_ON,
	.snvs_on_mask = LDO5_SNVS_ON,
	.suspend_on_mask = LDO5_SUSP_ON,
	.lpsr_on_mask = LDO5_LPSR_ON,
	};

	static const struct rohm_dvs_config dvref_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_on_mask = DVREF_RUN_ON,
	.snvs_on_mask = DVREF_SNVS_ON,
	.suspend_on_mask = DVREF_SUSP_ON,
	.lpsr_on_mask = DVREF_LPSR_ON,
	};

	static const struct rohm_dvs_config ldolpsr_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_on_mask = DVREF_RUN_ON,
	.snvs_on_mask = DVREF_SNVS_ON,
	.suspend_on_mask = DVREF_SUSP_ON,
	.lpsr_on_mask = DVREF_LPSR_ON,
	};

	static const struct rohm_dvs_config buck5_dvs = {
	.level_map = ROHM_DVS_LEVEL_RUN \| ROHM_DVS_LEVEL_SNVS \|
	ROHM_DVS_LEVEL_SUSPEND \| ROHM_DVS_LEVEL_LPSR,
	.run_reg = BD71815_REG_BUCK5_VOLT,
	.run_mask = BD71815_VOLT_MASK,
	.run_on_mask = BD71815_BUCK_RUN_ON,
	.snvs_on_mask = BD71815_BUCK_SNVS_ON,
	.suspend_on_mask = BD71815_BUCK_SUSP_ON,
	.lpsr_on_mask = BD71815_BUCK_LPSR_ON,
	};

	static int set_hw_dvs_levels(struct device_node *np,
	const struct regulator_desc *desc,
	struct regulator_config *cfg)
	{
	struct bd71815_regulator *data;

	data = container_of(desc, struct bd71815_regulator, desc);
	return rohm_regulator_set_dvs_levels(data->dvs, np, desc, cfg->regmap);
	}

	/*
	* Bucks 1 and 2 have two voltage selection registers where selected
	* voltage can be set. Which of the registers is used can be either controlled
	* by a control bit in register - or by HW state. If HW state specific voltages
	* are given - then we assume HW state based control should be used.
	*
	* If volatge value is updated to currently selected register - then output
	* voltage is immediately changed no matter what is set as ramp rate. Thus we
	* default changing voltage by writing new value to inactive register and
	* then updating the 'register selection' bit. This naturally only works when
	* HW state machine is not used to select the voltage.
	*/
	static int buck12_set_hw_dvs_levels(struct device_node *np,
	const struct regulator_desc *desc,
	struct regulator_config *cfg)
	{
	struct bd71815_regulator *data;
	int ret = 0, val;

	data = container_of(desc, struct bd71815_regulator, desc);

	if (of_find_property(np, "rohm,dvs-run-voltage", NULL) \|\|
	of_find_property(np, "rohm,dvs-suspend-voltage", NULL) \|\|
	of_find_property(np, "rohm,dvs-lpsr-voltage", NULL) \|\|
	of_find_property(np, "rohm,dvs-snvs-voltage", NULL)) {
	ret = regmap_read(cfg->regmap, desc->vsel_reg, &val);
	if (ret)
	return ret;

	if (!(BD71815_BUCK_STBY_DVS & val) &&
	!(BD71815_BUCK_DVSSEL & val)) {
	int val2;

	/*
	* We are currently using voltage from _L.
	* We'd better copy it to _H and switch to it to
	* avoid shutting us down if LPSR or SUSPEND is set to
	* disabled. _L value is at reg _H + 1
	*/
	ret = regmap_read(cfg->regmap, desc->vsel_reg + 1,
	&val2);
	if (ret)
	return ret;

	ret = regmap_update_bits(cfg->regmap, desc->vsel_reg,
	BD71815_VOLT_MASK \|
	BD71815_BUCK_DVSSEL,
	val2 \| BD71815_BUCK_DVSSEL);
	if (ret)
	return ret;
	}
	ret = rohm_regulator_set_dvs_levels(data->dvs, np, desc,
	cfg->regmap);
	if (ret)
	return ret;
	/*
	* DVS levels were given => use HW-state machine for voltage
	* controls. NOTE: AFAIK, This means that if voltage is changed
	* by SW the ramp-rate is not respected. Should we disable
	* SW voltage control when the HW state machine is used?
	*/
	ret = regmap_update_bits(cfg->regmap, desc->vsel_reg,
	BD71815_BUCK_STBY_DVS,
	BD71815_BUCK_STBY_DVS);
	}

	return ret;
	}

	/*
	* BUCK1/2
	* BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
	* 00: 10.00mV/usec 10mV 1uS
	* 01: 5.00mV/usec 10mV 2uS
	* 10: 2.50mV/usec 10mV 4uS
	* 11: 1.25mV/usec 10mV 8uS
	*/
	static const unsigned int bd7181x_ramp_table[] = { 1250, 2500, 5000, 10000 };

	static int bd7181x_led_set_current_limit(struct regulator_dev *rdev,
	int min_uA, int max_uA)
	{
	int ret;
	int onstatus;

	onstatus = regulator_is_enabled_regmap(rdev);

	ret = regulator_set_current_limit_regmap(rdev, min_uA, max_uA);
	if (!ret) {
	int newstatus;

	newstatus = regulator_is_enabled_regmap(rdev);
	if (onstatus != newstatus) {
	/*
	* HW FIX: spurious led status change detected. Toggle
	* state as a workaround
	*/
	if (onstatus)
	ret = regulator_enable_regmap(rdev);
	else
	ret = regulator_disable_regmap(rdev);

	if (ret)
	dev_err(rdev_get_dev(rdev),
	"failed to revert the LED state (%d)\n",
	ret);
	}
	}

	return ret;
	}

	static int bd7181x_buck12_get_voltage_sel(struct regulator_dev *rdev)
	{
	int rid = rdev_get_id(rdev);
	int ret, regh, regl, val;

	regh = BD71815_REG_BUCK1_VOLT_H + rid * 0x2;
	regl = BD71815_REG_BUCK1_VOLT_L + rid * 0x2;

	ret = regmap_read(rdev->regmap, regh, &val);
	if (ret)
	return ret;

	/*
	* If we use HW state machine based voltage reg selection - then we
	* return BD71815_REG_BUCK1_VOLT_H which is used at RUN.
	* Else we do return the BD71815_REG_BUCK1_VOLT_H or
	* BD71815_REG_BUCK1_VOLT_L depending on which is selected to be used
	* by BD71815_BUCK_DVSSEL bit
	*/
	if ((!(val & BD71815_BUCK_STBY_DVS)) && (!(val & BD71815_BUCK_DVSSEL)))
	ret = regmap_read(rdev->regmap, regl, &val);

	if (ret)
	return ret;

	return val & BD71815_VOLT_MASK;
	}

	/*
	* For Buck 1/2.
	*/
	static int bd7181x_buck12_set_voltage_sel(struct regulator_dev *rdev,
	unsigned int sel)
	{
	int rid = rdev_get_id(rdev);
	int ret, val, reg, regh, regl;

	regh = BD71815_REG_BUCK1_VOLT_H + rid*0x2;
	regl = BD71815_REG_BUCK1_VOLT_L + rid*0x2;

	ret = regmap_read(rdev->regmap, regh, &val);
	if (ret)
	return ret;

	/*
	* If bucks 1 & 2 are controlled by state machine - then the RUN state
	* voltage is set to BD71815_REG_BUCK1_VOLT_H. Changing SUSPEND/LPSR
	* voltages at runtime is not supported by this driver.
	*/
	if (((val & BD71815_BUCK_STBY_DVS))) {
	return regmap_update_bits(rdev->regmap, regh, BD71815_VOLT_MASK,
	sel);
	}
	/* Update new voltage to the register which is not selected now */
	if (val & BD71815_BUCK_DVSSEL)
	reg = regl;
	else
	reg = regh;

	ret = regmap_update_bits(rdev->regmap, reg, BD71815_VOLT_MASK, sel);
	if (ret)
	return ret;

	/* Select the other DVS register to be used */
	return regmap_update_bits(rdev->regmap, regh, BD71815_BUCK_DVSSEL,
	~val);
	}

	static const struct regulator_ops bd7181x_ldo_regulator_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_linear,
	.set_voltage_sel = regulator_set_voltage_sel_regmap,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
	};

	static const struct regulator_ops bd7181x_fixed_regulator_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_linear,
	};

	static const struct regulator_ops bd7181x_buck_regulator_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_linear,
	.set_voltage_sel = regulator_set_voltage_sel_regmap,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
	.set_voltage_time_sel = regulator_set_voltage_time_sel,
	};

	static const struct regulator_ops bd7181x_buck12_regulator_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_linear,
	.set_voltage_sel = bd7181x_buck12_set_voltage_sel,
	.get_voltage_sel = bd7181x_buck12_get_voltage_sel,
	.set_voltage_time_sel = regulator_set_voltage_time_sel,
	.set_ramp_delay = regulator_set_ramp_delay_regmap,
	};

	static const struct regulator_ops bd7181x_led_regulator_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.set_current_limit = bd7181x_led_set_current_limit,
	.get_current_limit = regulator_get_current_limit_regmap,
	};

	#define BD71815_FIXED_REG(_name, _id, ereg, emsk, voltage, _dvs) \
	[(_id)] = { \
	.desc = { \
	.name = #_name, \
	.of_match = of_match_ptr(#_name), \
	.regulators_node = of_match_ptr("regulators"), \
	.n_voltages = 1, \
	.ops = &bd7181x_fixed_regulator_ops, \
	.type = REGULATOR_VOLTAGE, \
	.id = (_id), \
	.owner = THIS_MODULE, \
	.min_uV = (voltage), \
	.enable_reg = (ereg), \
	.enable_mask = (emsk), \
	.of_parse_cb = set_hw_dvs_levels, \
	}, \
	.dvs = (_dvs), \
	}

	#define BD71815_BUCK_REG(_name, _id, vsel, ereg, min, max, step, _dvs) \
	[(_id)] = { \
	.desc = { \
	.name = #_name, \
	.of_match = of_match_ptr(#_name), \
	.regulators_node = of_match_ptr("regulators"), \
	.n_voltages = ((max) - (min)) / (step) + 1, \
	.ops = &bd7181x_buck_regulator_ops, \
	.type = REGULATOR_VOLTAGE, \
	.id = (_id), \
	.owner = THIS_MODULE, \
	.min_uV = (min), \
	.uV_step = (step), \
	.vsel_reg = (vsel), \
	.vsel_mask = BD71815_VOLT_MASK, \
	.enable_reg = (ereg), \
	.enable_mask = BD71815_BUCK_RUN_ON, \
	.of_parse_cb = set_hw_dvs_levels, \
	}, \
	.dvs = (_dvs), \
	}

	#define BD71815_BUCK12_REG(_name, _id, vsel, ereg, min, max, step, \
	_dvs) \
	[(_id)] = { \
	.desc = { \
	.name = #_name, \
	.of_match = of_match_ptr(#_name), \
	.regulators_node = of_match_ptr("regulators"), \
	.n_voltages = ((max) - (min)) / (step) + 1, \
	.ops = &bd7181x_buck12_regulator_ops, \
	.type = REGULATOR_VOLTAGE, \
	.id = (_id), \
	.owner = THIS_MODULE, \
	.min_uV = (min), \
	.uV_step = (step), \
	.vsel_reg = (vsel), \
	.vsel_mask = BD71815_VOLT_MASK, \
	.enable_reg = (ereg), \
	.enable_mask = BD71815_BUCK_RUN_ON, \
	.ramp_reg = (ereg), \
	.ramp_mask = BD71815_BUCK_RAMPRATE_MASK, \
	.ramp_delay_table = bd7181x_ramp_table, \
	.n_ramp_values = ARRAY_SIZE(bd7181x_ramp_table),\
	.of_parse_cb = buck12_set_hw_dvs_levels, \
	}, \
	.dvs = (_dvs), \
	}

	#define BD71815_LED_REG(_name, _id, csel, mask, ereg, emsk, currents) \
	[(_id)] = { \
	.desc = { \
	.name = #_name, \
	.of_match = of_match_ptr(#_name), \
	.regulators_node = of_match_ptr("regulators"), \
	.n_current_limits = ARRAY_SIZE(currents), \
	.ops = &bd7181x_led_regulator_ops, \
	.type = REGULATOR_CURRENT, \
	.id = (_id), \
	.owner = THIS_MODULE, \
	.curr_table = currents, \
	.csel_reg = (csel), \
	.csel_mask = (mask), \
	.enable_reg = (ereg), \
	.enable_mask = (emsk), \
	}, \
	}

	#define BD71815_LDO_REG(_name, _id, vsel, ereg, emsk, min, max, step, \
	_dvs) \
	[(_id)] = { \
	.desc = { \
	.name = #_name, \
	.of_match = of_match_ptr(#_name), \
	.regulators_node = of_match_ptr("regulators"), \
	.n_voltages = ((max) - (min)) / (step) + 1, \
	.ops = &bd7181x_ldo_regulator_ops, \
	.type = REGULATOR_VOLTAGE, \
	.id = (_id), \
	.owner = THIS_MODULE, \
	.min_uV = (min), \
	.uV_step = (step), \
	.vsel_reg = (vsel), \
	.vsel_mask = BD71815_VOLT_MASK, \
	.enable_reg = (ereg), \
	.enable_mask = (emsk), \
	.of_parse_cb = set_hw_dvs_levels, \
	}, \
	.dvs = (_dvs), \
	}

	static const struct bd71815_regulator bd71815_regulators[] = {
	BD71815_BUCK12_REG(buck1, BD71815_BUCK1, BD71815_REG_BUCK1_VOLT_H,
	BD71815_REG_BUCK1_MODE, 800000, 2000000, 25000,
	&buck1_dvs),
	BD71815_BUCK12_REG(buck2, BD71815_BUCK2, BD71815_REG_BUCK2_VOLT_H,
	BD71815_REG_BUCK2_MODE, 800000, 2000000, 25000,
	&buck2_dvs),
	BD71815_BUCK_REG(buck3, BD71815_BUCK3, BD71815_REG_BUCK3_VOLT,
	BD71815_REG_BUCK3_MODE, 1200000, 2700000, 50000,
	&buck3_dvs),
	BD71815_BUCK_REG(buck4, BD71815_BUCK4, BD71815_REG_BUCK4_VOLT,
	BD71815_REG_BUCK4_MODE, 1100000, 1850000, 25000,
	&buck4_dvs),
	BD71815_BUCK_REG(buck5, BD71815_BUCK5, BD71815_REG_BUCK5_VOLT,
	BD71815_REG_BUCK5_MODE, 1800000, 3300000, 50000,
	&buck5_dvs),
	BD71815_LDO_REG(ldo1, BD71815_LDO1, BD71815_REG_LDO1_VOLT,
	BD71815_REG_LDO_MODE1, LDO1_RUN_ON, 800000, 3300000,
	50000, &ldo1_dvs),
	BD71815_LDO_REG(ldo2, BD71815_LDO2, BD71815_REG_LDO2_VOLT,
	BD71815_REG_LDO_MODE2, LDO2_RUN_ON, 800000, 3300000,
	50000, &ldo2_dvs),
	/*
	* Let's default LDO3 to be enabled by SW. We can override ops if DT
	* says LDO3 should be enabled by HW when DCIN is connected.
	*/
	BD71815_LDO_REG(ldo3, BD71815_LDO3, BD71815_REG_LDO3_VOLT,
	BD71815_REG_LDO_MODE2, LDO3_RUN_ON, 800000, 3300000,
	50000, &ldo3_dvs),
	BD71815_LDO_REG(ldo4, BD71815_LDO4, BD71815_REG_LDO4_VOLT,
	BD71815_REG_LDO_MODE3, LDO4_RUN_ON, 800000, 3300000,
	50000, &ldo4_dvs),
	BD71815_LDO_REG(ldo5, BD71815_LDO5, BD71815_REG_LDO5_VOLT_H,
	BD71815_REG_LDO_MODE3, LDO5_RUN_ON, 800000, 3300000,
	50000, &ldo5_dvs),
	BD71815_FIXED_REG(ldodvref, BD71815_LDODVREF, BD71815_REG_LDO_MODE4,
	DVREF_RUN_ON, 3000000, &dvref_dvs),
	BD71815_FIXED_REG(ldolpsr, BD71815_LDOLPSR, BD71815_REG_LDO_MODE4,
	LDO_LPSR_RUN_ON, 1800000, &ldolpsr_dvs),
	BD71815_LED_REG(wled, BD71815_WLED, BD71815_REG_LED_DIMM, LED_DIMM_MASK,
	BD71815_REG_LED_CTRL, LED_RUN_ON,
	bd7181x_wled_currents),
	};

	static int bd7181x_probe(struct platform_device *pdev)
	{
	struct regulator_config config = {};
	int i, ret;
	struct gpio_desc *ldo4_en;
	struct regmap *regmap;

	regmap = dev_get_regmap(pdev->dev.parent, NULL);
	if (!regmap) {
	dev_err(&pdev->dev, "No parent regmap\n");
	return -ENODEV;
	}
	ldo4_en = devm_gpiod_get_from_of_node(&pdev->dev,
	pdev->dev.parent->of_node,
	"rohm,vsel-gpios", 0,
	GPIOD_ASIS, "ldo4-en");

	if (IS_ERR(ldo4_en)) {
	ret = PTR_ERR(ldo4_en);
	if (ret != -ENOENT)
	return ret;
	ldo4_en = NULL;
	}

	/* Disable to go to ship-mode */
	ret = regmap_update_bits(regmap, BD71815_REG_PWRCTRL, RESTARTEN, 0);
	if (ret)
	return ret;

	config.dev = pdev->dev.parent;
	config.regmap = regmap;

	for (i = 0; i < BD71815_REGULATOR_CNT; i++) {
	const struct regulator_desc *desc;
	struct regulator_dev *rdev;

	desc = &bd71815_regulators[i].desc;

	if (i == BD71815_LDO4)
	config.ena_gpiod = ldo4_en;
	else
	config.ena_gpiod = NULL;

	rdev = devm_regulator_register(&pdev->dev, desc, &config);
	if (IS_ERR(rdev)) {
	dev_err(&pdev->dev,
	"failed to register %s regulator\n",
	desc->name);
	return PTR_ERR(rdev);
	}
	}
	return 0;
	}

	static const struct platform_device_id bd7181x_pmic_id[] = {
	{ "bd71815-pmic", ROHM_CHIP_TYPE_BD71815 },
	{ },
	};
	MODULE_DEVICE_TABLE(platform, bd7181x_pmic_id);

	static struct platform_driver bd7181x_regulator = {
	.driver = {
	.name = "bd7181x-pmic",
	},
	.probe = bd7181x_probe,
	.id_table = bd7181x_pmic_id,
	};
	module_platform_driver(bd7181x_regulator);

	MODULE_AUTHOR("Tony Luo <luofc@embedinfo.com>");
	MODULE_DESCRIPTION("BD71815 voltage regulator driver");
	MODULE_LICENSE("GPL v2");
	MODULE_ALIAS("platform:bd7181x-pmic");