drivers/net/phy/bcm7xxx.c - linux - Git at Google

 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Broadcom BCM7xxx internal transceivers support.
  *
  * Copyright (C) 2014-2017 Broadcom
  */

 #include <linux/module.h>
 #include <linux/phy.h>
 #include <linux/delay.h>
 #include "bcm-phy-lib.h"
 #include <linux/bitops.h>
 #include <linux/brcmphy.h>
 #include <linux/mdio.h>

 /* Broadcom BCM7xxx internal PHY registers */

 /* EPHY only register definitions */
 #define MII_BCM7XXX_100TX_AUX_CTL	0x10
 #define MII_BCM7XXX_100TX_FALSE_CAR	0x13
 #define MII_BCM7XXX_100TX_DISC		0x14
 #define MII_BCM7XXX_AUX_MODE		0x1d
 #define  MII_BCM7XXX_64CLK_MDIO		BIT(12)
 #define MII_BCM7XXX_TEST		0x1f
 #define  MII_BCM7XXX_SHD_MODE_2		BIT(2)
 #define MII_BCM7XXX_SHD_2_ADDR_CTRL	0xe
 #define MII_BCM7XXX_SHD_2_CTRL_STAT	0xf
 #define MII_BCM7XXX_SHD_2_BIAS_TRIM	0x1a
 #define MII_BCM7XXX_SHD_3_AN_EEE_ADV	0x3
 #define MII_BCM7XXX_SHD_3_PCS_CTRL_2	0x6
 #define  MII_BCM7XXX_PCS_CTRL_2_DEF	0x4400
 #define MII_BCM7XXX_SHD_3_AN_STAT	0xb
 #define  MII_BCM7XXX_AN_NULL_MSG_EN	BIT(0)
 #define  MII_BCM7XXX_AN_EEE_EN		BIT(1)
 #define MII_BCM7XXX_SHD_3_EEE_THRESH	0xe
 #define  MII_BCM7XXX_EEE_THRESH_DEF	0x50
 #define MII_BCM7XXX_SHD_3_TL4		0x23
 #define  MII_BCM7XXX_TL4_RST_MSK	(BIT(2) | BIT(1))

 struct bcm7xxx_phy_priv {
 	u64	*stats;
 };

 static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev)
 {
 	/* AFE_RXCONFIG_0 */
 	bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15);

 	/* AFE_RXCONFIG_1 */
 	bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);

 	/* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */
 	bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003);

 	/* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */
 	bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);

 	/* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */
 	bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);

 	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
 	bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);

 	/* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */
 	bcm_phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020);

 	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
 	 * offset for HT=0 code
 	 */
 	bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);

 	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
 	phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010);

 	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
 	bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b);

 	/* Reset R_CAL/RC_CAL engine */
 	bcm_phy_r_rc_cal_reset(phydev);

 	return 0;
 }

 static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev)
 {
 	/* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */
 	bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);

 	/* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */
 	bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);

 	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
 	bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);

 	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
 	 * offset for HT=0 code
 	 */
 	bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);

 	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
 	phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010);

 	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
 	bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b);

 	/* Reset R_CAL/RC_CAL engine */
 	bcm_phy_r_rc_cal_reset(phydev);

 	return 0;
 }

 static int bcm7xxx_28nm_a0_patch_afe_config_init(struct phy_device *phydev)
 {
 	/* +1 RC_CAL codes for RL centering for both LT and HT conditions */
 	bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0xd003);

 	/* Cut master bias current by 2% to compensate for RC_CAL offset */
 	bcm_phy_write_misc(phydev, DSP_TAP10, 0x791b);

 	/* Improve hybrid leakage */
 	bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x10e3);

 	/* Change rx_on_tune 8 to 0xf */
 	bcm_phy_write_misc(phydev, 0x21, 0x2, 0x87f6);

 	/* Change 100Tx EEE bandwidth */
 	bcm_phy_write_misc(phydev, 0x22, 0x2, 0x017d);

 	/* Enable ffe zero detection for Vitesse interoperability */
 	bcm_phy_write_misc(phydev, 0x26, 0x2, 0x0015);

 	bcm_phy_r_rc_cal_reset(phydev);

 	return 0;
 }

 static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
 {
 	u8 rev = PHY_BRCM_7XXX_REV(phydev->dev_flags);
 	u8 patch = PHY_BRCM_7XXX_PATCH(phydev->dev_flags);
 	u8 count;
 	int ret = 0;

 	/* Newer devices have moved the revision information back into a
 	 * standard location in MII_PHYS_ID[23]
 	 */
 	if (rev == 0)
 		rev = phydev->phy_id & ~phydev->drv->phy_id_mask;

 	pr_info_once("%s: %s PHY revision: 0x%02x, patch: %d\n",
 		     phydev_name(phydev), phydev->drv->name, rev, patch);

 	/* Dummy read to a register to workaround an issue upon reset where the
 	 * internal inverter may not allow the first MDIO transaction to pass
 	 * the MDIO management controller and make us return 0xffff for such
 	 * reads.
 	 */
 	phy_read(phydev, MII_BMSR);

 	switch (rev) {
 	case 0xa0:
 	case 0xb0:
 		ret = bcm_phy_28nm_a0b0_afe_config_init(phydev);
 		break;
 	case 0xd0:
 		ret = bcm7xxx_28nm_d0_afe_config_init(phydev);
 		break;
 	case 0xe0:
 	case 0xf0:
 	/* Rev G0 introduces a roll over */
 	case 0x10:
 		ret = bcm7xxx_28nm_e0_plus_afe_config_init(phydev);
 		break;
 	case 0x01:
 		ret = bcm7xxx_28nm_a0_patch_afe_config_init(phydev);
 		break;
 	default:
 		break;
 	}

 	if (ret)
 		return ret;

 	ret = bcm_phy_downshift_get(phydev, &count);
 	if (ret)
 		return ret;

 	/* Only enable EEE if Wirespeed/downshift is disabled */
 	ret = bcm_phy_set_eee(phydev, count == DOWNSHIFT_DEV_DISABLE);
 	if (ret)
 		return ret;

 	return bcm_phy_enable_apd(phydev, true);
 }

 static int bcm7xxx_28nm_resume(struct phy_device *phydev)
 {
 	int ret;

 	/* Re-apply workarounds coming out suspend/resume */
 	ret = bcm7xxx_28nm_config_init(phydev);
 	if (ret)
 		return ret;

 	/* 28nm Gigabit PHYs come out of reset without any half-duplex
 	 * or "hub" compliant advertised mode, fix that. This does not
 	 * cause any problems with the PHY library since genphy_config_aneg()
 	 * gracefully handles auto-negotiated and forced modes.
 	 */
 	return genphy_config_aneg(phydev);
 }

 static int phy_set_clr_bits(struct phy_device *dev, int location,
 					int set_mask, int clr_mask)
 {
 	int v, ret;

 	v = phy_read(dev, location);
 	if (v < 0)
 		return v;

 	v &= ~clr_mask;
 	v |= set_mask;

 	ret = phy_write(dev, location, v);
 	if (ret < 0)
 		return ret;

 	return v;
 }

 static int bcm7xxx_28nm_ephy_01_afe_config_init(struct phy_device *phydev)
 {
 	int ret;

 	/* set shadow mode 2 */
 	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
 			       MII_BCM7XXX_SHD_MODE_2, 0);
 	if (ret < 0)
 		return ret;

 	/* Set current trim values INT_trim = -1, Ext_trim =0 */
 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_BIAS_TRIM, 0x3BE0);
 	if (ret < 0)
 		goto reset_shadow_mode;

 	/* Cal reset */
 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
 			MII_BCM7XXX_SHD_3_TL4);
 	if (ret < 0)
 		goto reset_shadow_mode;
 	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
 			       MII_BCM7XXX_TL4_RST_MSK, 0);
 	if (ret < 0)
 		goto reset_shadow_mode;

 	/* Cal reset disable */
 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
 			MII_BCM7XXX_SHD_3_TL4);
 	if (ret < 0)
 		goto reset_shadow_mode;
 	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
 			       0, MII_BCM7XXX_TL4_RST_MSK);
 	if (ret < 0)
 		goto reset_shadow_mode;

 reset_shadow_mode:
 	/* reset shadow mode 2 */
 	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0,
 			       MII_BCM7XXX_SHD_MODE_2);
 	if (ret < 0)
 		return ret;

 	return 0;
 }

 /* The 28nm EPHY does not support Clause 45 (MMD) used by bcm-phy-lib */
 static int bcm7xxx_28nm_ephy_apd_enable(struct phy_device *phydev)
 {
 	int ret;

 	/* set shadow mode 1 */
 	ret = phy_set_clr_bits(phydev, MII_BRCM_FET_BRCMTEST,
 			       MII_BRCM_FET_BT_SRE, 0);
 	if (ret < 0)
 		return ret;

 	/* Enable auto-power down */
 	ret = phy_set_clr_bits(phydev, MII_BRCM_FET_SHDW_AUXSTAT2,
 			       MII_BRCM_FET_SHDW_AS2_APDE, 0);
 	if (ret < 0)
 		return ret;

 	/* reset shadow mode 1 */
 	ret = phy_set_clr_bits(phydev, MII_BRCM_FET_BRCMTEST, 0,
 			       MII_BRCM_FET_BT_SRE);
 	if (ret < 0)
 		return ret;

 	return 0;
 }

 static int bcm7xxx_28nm_ephy_eee_enable(struct phy_device *phydev)
 {
 	int ret;

 	/* set shadow mode 2 */
 	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
 			       MII_BCM7XXX_SHD_MODE_2, 0);
 	if (ret < 0)
 		return ret;

 	/* Advertise supported modes */
 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
 			MII_BCM7XXX_SHD_3_AN_EEE_ADV);
 	if (ret < 0)
 		goto reset_shadow_mode;
 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
 			MDIO_EEE_100TX);
 	if (ret < 0)
 		goto reset_shadow_mode;

 	/* Restore Defaults */
 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
 			MII_BCM7XXX_SHD_3_PCS_CTRL_2);
 	if (ret < 0)
 		goto reset_shadow_mode;
 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
 			MII_BCM7XXX_PCS_CTRL_2_DEF);
 	if (ret < 0)
 		goto reset_shadow_mode;

 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
 			MII_BCM7XXX_SHD_3_EEE_THRESH);
 	if (ret < 0)
 		goto reset_shadow_mode;
 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
 			MII_BCM7XXX_EEE_THRESH_DEF);
 	if (ret < 0)
 		goto reset_shadow_mode;

 	/* Enable EEE autonegotiation */
 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
 			MII_BCM7XXX_SHD_3_AN_STAT);
 	if (ret < 0)
 		goto reset_shadow_mode;
 	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
 			(MII_BCM7XXX_AN_NULL_MSG_EN | MII_BCM7XXX_AN_EEE_EN));
 	if (ret < 0)
 		goto reset_shadow_mode;

 reset_shadow_mode:
 	/* reset shadow mode 2 */
 	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0,
 			       MII_BCM7XXX_SHD_MODE_2);
 	if (ret < 0)
 		return ret;

 	/* Restart autoneg */
 	phy_write(phydev, MII_BMCR,
 		  (BMCR_SPEED100 | BMCR_ANENABLE | BMCR_ANRESTART));

 	return 0;
 }

 static int bcm7xxx_28nm_ephy_config_init(struct phy_device *phydev)
 {
 	u8 rev = phydev->phy_id & ~phydev->drv->phy_id_mask;
 	int ret = 0;

 	pr_info_once("%s: %s PHY revision: 0x%02x\n",
 		     phydev_name(phydev), phydev->drv->name, rev);

 	/* Dummy read to a register to workaround a possible issue upon reset
 	 * where the internal inverter may not allow the first MDIO transaction
 	 * to pass the MDIO management controller and make us return 0xffff for
 	 * such reads.
 	 */
 	phy_read(phydev, MII_BMSR);

 	/* Apply AFE software work-around if necessary */
 	if (rev == 0x01) {
 		ret = bcm7xxx_28nm_ephy_01_afe_config_init(phydev);
 		if (ret)
 			return ret;
 	}

 	ret = bcm7xxx_28nm_ephy_eee_enable(phydev);
 	if (ret)
 		return ret;

 	return bcm7xxx_28nm_ephy_apd_enable(phydev);
 }

 static int bcm7xxx_28nm_ephy_resume(struct phy_device *phydev)
 {
 	int ret;

 	/* Re-apply workarounds coming out suspend/resume */
 	ret = bcm7xxx_28nm_ephy_config_init(phydev);
 	if (ret)
 		return ret;

 	return genphy_config_aneg(phydev);
 }

 static int bcm7xxx_config_init(struct phy_device *phydev)
 {
 	int ret;

 	/* Enable 64 clock MDIO */
 	phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XXX_64CLK_MDIO);
 	phy_read(phydev, MII_BCM7XXX_AUX_MODE);

 	/* set shadow mode 2 */
 	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
 			MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2);
 	if (ret < 0)
 		return ret;

 	/* set iddq_clkbias */
 	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00);
 	udelay(10);

 	/* reset iddq_clkbias */
 	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00);

 	phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555);

 	/* reset shadow mode 2 */
 	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0, MII_BCM7XXX_SHD_MODE_2);
 	if (ret < 0)
 		return ret;

 	return 0;
 }

 /* Workaround for putting the PHY in IDDQ mode, required
  * for all BCM7XXX 40nm and 65nm PHYs
  */
 static int bcm7xxx_suspend(struct phy_device *phydev)
 {
 	int ret;
 	static const struct bcm7xxx_regs {
 		int reg;
 		u16 value;
 	} bcm7xxx_suspend_cfg[] = {
 		{ MII_BCM7XXX_TEST, 0x008b },
 		{ MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 },
 		{ MII_BCM7XXX_100TX_DISC, 0x7000 },
 		{ MII_BCM7XXX_TEST, 0x000f },
 		{ MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 },
 		{ MII_BCM7XXX_TEST, 0x000b },
 	};
 	unsigned int i;

 	for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) {
 		ret = phy_write(phydev,
 				bcm7xxx_suspend_cfg[i].reg,
 				bcm7xxx_suspend_cfg[i].value);
 		if (ret)
 			return ret;
 	}

 	return 0;
 }

 static int bcm7xxx_28nm_get_tunable(struct phy_device *phydev,
 				    struct ethtool_tunable *tuna,
 				    void *data)
 {
 	switch (tuna->id) {
 	case ETHTOOL_PHY_DOWNSHIFT:
 		return bcm_phy_downshift_get(phydev, (u8 *)data);
 	default:
 		return -EOPNOTSUPP;
 	}
 }

 static int bcm7xxx_28nm_set_tunable(struct phy_device *phydev,
 				    struct ethtool_tunable *tuna,
 				    const void *data)
 {
 	u8 count = *(u8 *)data;
 	int ret;

 	switch (tuna->id) {
 	case ETHTOOL_PHY_DOWNSHIFT:
 		ret = bcm_phy_downshift_set(phydev, count);
 		break;
 	default:
 		return -EOPNOTSUPP;
 	}

 	if (ret)
 		return ret;

 	/* Disable EEE advertisement since this prevents the PHY
 	 * from successfully linking up, trigger auto-negotiation restart
 	 * to let the MAC decide what to do.
 	 */
 	ret = bcm_phy_set_eee(phydev, count == DOWNSHIFT_DEV_DISABLE);
 	if (ret)
 		return ret;

 	return genphy_restart_aneg(phydev);
 }

 static void bcm7xxx_28nm_get_phy_stats(struct phy_device *phydev,
 				       struct ethtool_stats *stats, u64 *data)
 {
 	struct bcm7xxx_phy_priv *priv = phydev->priv;

 	bcm_phy_get_stats(phydev, priv->stats, stats, data);
 }

 static int bcm7xxx_28nm_probe(struct phy_device *phydev)
 {
 	struct bcm7xxx_phy_priv *priv;

 	priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;

 	phydev->priv = priv;

 	priv->stats = devm_kcalloc(&phydev->mdio.dev,
 				   bcm_phy_get_sset_count(phydev), sizeof(u64),
 				   GFP_KERNEL);
 	if (!priv->stats)
 		return -ENOMEM;

 	return 0;
 }

 #define BCM7XXX_28NM_GPHY(_oui, _name)					\
 {									\
 	.phy_id		= (_oui),					\
 	.phy_id_mask	= 0xfffffff0,					\
 	.name		= _name,					\
 	/* PHY_GBIT_FEATURES */						\
 	.flags		= PHY_IS_INTERNAL,				\
 	.config_init	= bcm7xxx_28nm_config_init,			\
 	.resume		= bcm7xxx_28nm_resume,				\
 	.get_tunable	= bcm7xxx_28nm_get_tunable,			\
 	.set_tunable	= bcm7xxx_28nm_set_tunable,			\
 	.get_sset_count	= bcm_phy_get_sset_count,			\
 	.get_strings	= bcm_phy_get_strings,				\
 	.get_stats	= bcm7xxx_28nm_get_phy_stats,			\
 	.probe		= bcm7xxx_28nm_probe,				\
 }

 #define BCM7XXX_28NM_EPHY(_oui, _name)					\
 {									\
 	.phy_id		= (_oui),					\
 	.phy_id_mask	= 0xfffffff0,					\
 	.name		= _name,					\
 	/* PHY_BASIC_FEATURES */					\
 	.flags		= PHY_IS_INTERNAL,				\
 	.config_init	= bcm7xxx_28nm_ephy_config_init,		\
 	.resume		= bcm7xxx_28nm_ephy_resume,			\
 	.get_sset_count	= bcm_phy_get_sset_count,			\
 	.get_strings	= bcm_phy_get_strings,				\
 	.get_stats	= bcm7xxx_28nm_get_phy_stats,			\
 	.probe		= bcm7xxx_28nm_probe,				\
 }

 #define BCM7XXX_40NM_EPHY(_oui, _name)					\
 {									\
 	.phy_id         = (_oui),					\
 	.phy_id_mask    = 0xfffffff0,					\
 	.name           = _name,					\
 	/* PHY_BASIC_FEATURES */					\
 	.flags          = PHY_IS_INTERNAL,				\
 	.config_init    = bcm7xxx_config_init,				\
 	.suspend        = bcm7xxx_suspend,				\
 	.resume         = bcm7xxx_config_init,				\
 }

 static struct phy_driver bcm7xxx_driver[] = {
 	BCM7XXX_28NM_GPHY(PHY_ID_BCM7250, "Broadcom BCM7250"),
 	BCM7XXX_28NM_EPHY(PHY_ID_BCM7255, "Broadcom BCM7255"),
 	BCM7XXX_28NM_EPHY(PHY_ID_BCM7260, "Broadcom BCM7260"),
 	BCM7XXX_28NM_EPHY(PHY_ID_BCM7268, "Broadcom BCM7268"),
 	BCM7XXX_28NM_EPHY(PHY_ID_BCM7271, "Broadcom BCM7271"),
 	BCM7XXX_28NM_GPHY(PHY_ID_BCM7278, "Broadcom BCM7278"),
 	BCM7XXX_28NM_GPHY(PHY_ID_BCM7364, "Broadcom BCM7364"),
 	BCM7XXX_28NM_GPHY(PHY_ID_BCM7366, "Broadcom BCM7366"),
 	BCM7XXX_28NM_GPHY(PHY_ID_BCM74371, "Broadcom BCM74371"),
 	BCM7XXX_28NM_GPHY(PHY_ID_BCM7439, "Broadcom BCM7439"),
 	BCM7XXX_28NM_GPHY(PHY_ID_BCM7439_2, "Broadcom BCM7439 (2)"),
 	BCM7XXX_28NM_GPHY(PHY_ID_BCM7445, "Broadcom BCM7445"),
 	BCM7XXX_40NM_EPHY(PHY_ID_BCM7346, "Broadcom BCM7346"),
 	BCM7XXX_40NM_EPHY(PHY_ID_BCM7362, "Broadcom BCM7362"),
 	BCM7XXX_40NM_EPHY(PHY_ID_BCM7425, "Broadcom BCM7425"),
 	BCM7XXX_40NM_EPHY(PHY_ID_BCM7429, "Broadcom BCM7429"),
 	BCM7XXX_40NM_EPHY(PHY_ID_BCM7435, "Broadcom BCM7435"),
 };

 static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = {
 	{ PHY_ID_BCM7250, 0xfffffff0, },
 	{ PHY_ID_BCM7255, 0xfffffff0, },
 	{ PHY_ID_BCM7260, 0xfffffff0, },
 	{ PHY_ID_BCM7268, 0xfffffff0, },
 	{ PHY_ID_BCM7271, 0xfffffff0, },
 	{ PHY_ID_BCM7278, 0xfffffff0, },
 	{ PHY_ID_BCM7364, 0xfffffff0, },
 	{ PHY_ID_BCM7366, 0xfffffff0, },
 	{ PHY_ID_BCM7346, 0xfffffff0, },
 	{ PHY_ID_BCM7362, 0xfffffff0, },
 	{ PHY_ID_BCM7425, 0xfffffff0, },
 	{ PHY_ID_BCM7429, 0xfffffff0, },
 	{ PHY_ID_BCM74371, 0xfffffff0, },
 	{ PHY_ID_BCM7439, 0xfffffff0, },
 	{ PHY_ID_BCM7435, 0xfffffff0, },
 	{ PHY_ID_BCM7445, 0xfffffff0, },
 	{ }
 };

 module_phy_driver(bcm7xxx_driver);

 MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl);

 MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver");
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Broadcom Corporation");
	// SPDX-License-Identifier: GPL-2.0+
	/*
	* Broadcom BCM7xxx internal transceivers support.
	*
	* Copyright (C) 2014-2017 Broadcom
	*/

	#include <linux/module.h>
	#include <linux/phy.h>
	#include <linux/delay.h>
	#include "bcm-phy-lib.h"
	#include <linux/bitops.h>
	#include <linux/brcmphy.h>
	#include <linux/mdio.h>

	/* Broadcom BCM7xxx internal PHY registers */

	/* EPHY only register definitions */
	#define MII_BCM7XXX_100TX_AUX_CTL 0x10
	#define MII_BCM7XXX_100TX_FALSE_CAR 0x13
	#define MII_BCM7XXX_100TX_DISC 0x14
	#define MII_BCM7XXX_AUX_MODE 0x1d
	#define MII_BCM7XXX_64CLK_MDIO BIT(12)
	#define MII_BCM7XXX_TEST 0x1f
	#define MII_BCM7XXX_SHD_MODE_2 BIT(2)
	#define MII_BCM7XXX_SHD_2_ADDR_CTRL 0xe
	#define MII_BCM7XXX_SHD_2_CTRL_STAT 0xf
	#define MII_BCM7XXX_SHD_2_BIAS_TRIM 0x1a
	#define MII_BCM7XXX_SHD_3_AN_EEE_ADV 0x3
	#define MII_BCM7XXX_SHD_3_PCS_CTRL_2 0x6
	#define MII_BCM7XXX_PCS_CTRL_2_DEF 0x4400
	#define MII_BCM7XXX_SHD_3_AN_STAT 0xb
	#define MII_BCM7XXX_AN_NULL_MSG_EN BIT(0)
	#define MII_BCM7XXX_AN_EEE_EN BIT(1)
	#define MII_BCM7XXX_SHD_3_EEE_THRESH 0xe
	#define MII_BCM7XXX_EEE_THRESH_DEF 0x50
	#define MII_BCM7XXX_SHD_3_TL4 0x23
	#define MII_BCM7XXX_TL4_RST_MSK (BIT(2) \| BIT(1))

	struct bcm7xxx_phy_priv {
	u64 *stats;
	};

	static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev)
	{
	/* AFE_RXCONFIG_0 */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15);

	/* AFE_RXCONFIG_1 */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);

	/* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003);

	/* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */
	bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);

	/* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */
	bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);

	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
	bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);

	/* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */
	bcm_phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020);

	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
	* offset for HT=0 code
	*/
	bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);

	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
	phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010);

	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
	bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b);

	/* Reset R_CAL/RC_CAL engine */
	bcm_phy_r_rc_cal_reset(phydev);

	return 0;
	}

	static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev)
	{
	/* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);

	/* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */
	bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);

	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
	bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);

	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
	* offset for HT=0 code
	*/
	bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);

	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
	phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010);

	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
	bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b);

	/* Reset R_CAL/RC_CAL engine */
	bcm_phy_r_rc_cal_reset(phydev);

	return 0;
	}

	static int bcm7xxx_28nm_a0_patch_afe_config_init(struct phy_device *phydev)
	{
	/* +1 RC_CAL codes for RL centering for both LT and HT conditions */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0xd003);

	/* Cut master bias current by 2% to compensate for RC_CAL offset */
	bcm_phy_write_misc(phydev, DSP_TAP10, 0x791b);

	/* Improve hybrid leakage */
	bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x10e3);

	/* Change rx_on_tune 8 to 0xf */
	bcm_phy_write_misc(phydev, 0x21, 0x2, 0x87f6);

	/* Change 100Tx EEE bandwidth */
	bcm_phy_write_misc(phydev, 0x22, 0x2, 0x017d);

	/* Enable ffe zero detection for Vitesse interoperability */
	bcm_phy_write_misc(phydev, 0x26, 0x2, 0x0015);

	bcm_phy_r_rc_cal_reset(phydev);

	return 0;
	}

	static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
	{
	u8 rev = PHY_BRCM_7XXX_REV(phydev->dev_flags);
	u8 patch = PHY_BRCM_7XXX_PATCH(phydev->dev_flags);
	u8 count;
	int ret = 0;

	/* Newer devices have moved the revision information back into a
	* standard location in MII_PHYS_ID[23]
	*/
	if (rev == 0)
	rev = phydev->phy_id & ~phydev->drv->phy_id_mask;

	pr_info_once("%s: %s PHY revision: 0x%02x, patch: %d\n",
	phydev_name(phydev), phydev->drv->name, rev, patch);

	/* Dummy read to a register to workaround an issue upon reset where the
	* internal inverter may not allow the first MDIO transaction to pass
	* the MDIO management controller and make us return 0xffff for such
	* reads.
	*/
	phy_read(phydev, MII_BMSR);

	switch (rev) {
	case 0xa0:
	case 0xb0:
	ret = bcm_phy_28nm_a0b0_afe_config_init(phydev);
	break;
	case 0xd0:
	ret = bcm7xxx_28nm_d0_afe_config_init(phydev);
	break;
	case 0xe0:
	case 0xf0:
	/* Rev G0 introduces a roll over */
	case 0x10:
	ret = bcm7xxx_28nm_e0_plus_afe_config_init(phydev);
	break;
	case 0x01:
	ret = bcm7xxx_28nm_a0_patch_afe_config_init(phydev);
	break;
	default:
	break;
	}

	if (ret)
	return ret;

	ret = bcm_phy_downshift_get(phydev, &count);
	if (ret)
	return ret;

	/* Only enable EEE if Wirespeed/downshift is disabled */
	ret = bcm_phy_set_eee(phydev, count == DOWNSHIFT_DEV_DISABLE);
	if (ret)
	return ret;

	return bcm_phy_enable_apd(phydev, true);
	}

	static int bcm7xxx_28nm_resume(struct phy_device *phydev)
	{
	int ret;

	/* Re-apply workarounds coming out suspend/resume */
	ret = bcm7xxx_28nm_config_init(phydev);
	if (ret)
	return ret;

	/* 28nm Gigabit PHYs come out of reset without any half-duplex
	* or "hub" compliant advertised mode, fix that. This does not
	* cause any problems with the PHY library since genphy_config_aneg()
	* gracefully handles auto-negotiated and forced modes.
	*/
	return genphy_config_aneg(phydev);
	}

	static int phy_set_clr_bits(struct phy_device *dev, int location,
	int set_mask, int clr_mask)
	{
	int v, ret;

	v = phy_read(dev, location);
	if (v < 0)
	return v;

	v &= ~clr_mask;
	v \|= set_mask;

	ret = phy_write(dev, location, v);
	if (ret < 0)
	return ret;

	return v;
	}

	static int bcm7xxx_28nm_ephy_01_afe_config_init(struct phy_device *phydev)
	{
	int ret;

	/* set shadow mode 2 */
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
	MII_BCM7XXX_SHD_MODE_2, 0);
	if (ret < 0)
	return ret;

	/* Set current trim values INT_trim = -1, Ext_trim =0 */
	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_BIAS_TRIM, 0x3BE0);
	if (ret < 0)
	goto reset_shadow_mode;

	/* Cal reset */
	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
	MII_BCM7XXX_SHD_3_TL4);
	if (ret < 0)
	goto reset_shadow_mode;
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
	MII_BCM7XXX_TL4_RST_MSK, 0);
	if (ret < 0)
	goto reset_shadow_mode;

	/* Cal reset disable */
	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
	MII_BCM7XXX_SHD_3_TL4);
	if (ret < 0)
	goto reset_shadow_mode;
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
	0, MII_BCM7XXX_TL4_RST_MSK);
	if (ret < 0)
	goto reset_shadow_mode;

	reset_shadow_mode:
	/* reset shadow mode 2 */
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0,
	MII_BCM7XXX_SHD_MODE_2);
	if (ret < 0)
	return ret;

	return 0;
	}

	/* The 28nm EPHY does not support Clause 45 (MMD) used by bcm-phy-lib */
	static int bcm7xxx_28nm_ephy_apd_enable(struct phy_device *phydev)
	{
	int ret;

	/* set shadow mode 1 */
	ret = phy_set_clr_bits(phydev, MII_BRCM_FET_BRCMTEST,
	MII_BRCM_FET_BT_SRE, 0);
	if (ret < 0)
	return ret;

	/* Enable auto-power down */
	ret = phy_set_clr_bits(phydev, MII_BRCM_FET_SHDW_AUXSTAT2,
	MII_BRCM_FET_SHDW_AS2_APDE, 0);
	if (ret < 0)
	return ret;

	/* reset shadow mode 1 */
	ret = phy_set_clr_bits(phydev, MII_BRCM_FET_BRCMTEST, 0,
	MII_BRCM_FET_BT_SRE);
	if (ret < 0)
	return ret;

	return 0;
	}

	static int bcm7xxx_28nm_ephy_eee_enable(struct phy_device *phydev)
	{
	int ret;

	/* set shadow mode 2 */
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
	MII_BCM7XXX_SHD_MODE_2, 0);
	if (ret < 0)
	return ret;

	/* Advertise supported modes */
	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
	MII_BCM7XXX_SHD_3_AN_EEE_ADV);
	if (ret < 0)
	goto reset_shadow_mode;
	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
	MDIO_EEE_100TX);
	if (ret < 0)
	goto reset_shadow_mode;

	/* Restore Defaults */
	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
	MII_BCM7XXX_SHD_3_PCS_CTRL_2);
	if (ret < 0)
	goto reset_shadow_mode;
	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
	MII_BCM7XXX_PCS_CTRL_2_DEF);
	if (ret < 0)
	goto reset_shadow_mode;

	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
	MII_BCM7XXX_SHD_3_EEE_THRESH);
	if (ret < 0)
	goto reset_shadow_mode;
	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
	MII_BCM7XXX_EEE_THRESH_DEF);
	if (ret < 0)
	goto reset_shadow_mode;

	/* Enable EEE autonegotiation */
	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL,
	MII_BCM7XXX_SHD_3_AN_STAT);
	if (ret < 0)
	goto reset_shadow_mode;
	ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT,
	(MII_BCM7XXX_AN_NULL_MSG_EN \| MII_BCM7XXX_AN_EEE_EN));
	if (ret < 0)
	goto reset_shadow_mode;

	reset_shadow_mode:
	/* reset shadow mode 2 */
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0,
	MII_BCM7XXX_SHD_MODE_2);
	if (ret < 0)
	return ret;

	/* Restart autoneg */
	phy_write(phydev, MII_BMCR,
	(BMCR_SPEED100 \| BMCR_ANENABLE \| BMCR_ANRESTART));

	return 0;
	}

	static int bcm7xxx_28nm_ephy_config_init(struct phy_device *phydev)
	{
	u8 rev = phydev->phy_id & ~phydev->drv->phy_id_mask;
	int ret = 0;

	pr_info_once("%s: %s PHY revision: 0x%02x\n",
	phydev_name(phydev), phydev->drv->name, rev);

	/* Dummy read to a register to workaround a possible issue upon reset
	* where the internal inverter may not allow the first MDIO transaction
	* to pass the MDIO management controller and make us return 0xffff for
	* such reads.
	*/
	phy_read(phydev, MII_BMSR);

	/* Apply AFE software work-around if necessary */
	if (rev == 0x01) {
	ret = bcm7xxx_28nm_ephy_01_afe_config_init(phydev);
	if (ret)
	return ret;
	}

	ret = bcm7xxx_28nm_ephy_eee_enable(phydev);
	if (ret)
	return ret;

	return bcm7xxx_28nm_ephy_apd_enable(phydev);
	}

	static int bcm7xxx_28nm_ephy_resume(struct phy_device *phydev)
	{
	int ret;

	/* Re-apply workarounds coming out suspend/resume */
	ret = bcm7xxx_28nm_ephy_config_init(phydev);
	if (ret)
	return ret;

	return genphy_config_aneg(phydev);
	}

	static int bcm7xxx_config_init(struct phy_device *phydev)
	{
	int ret;

	/* Enable 64 clock MDIO */
	phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XXX_64CLK_MDIO);
	phy_read(phydev, MII_BCM7XXX_AUX_MODE);

	/* set shadow mode 2 */
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
	MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2);
	if (ret < 0)
	return ret;

	/* set iddq_clkbias */
	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00);
	udelay(10);

	/* reset iddq_clkbias */
	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00);

	phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555);

	/* reset shadow mode 2 */
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0, MII_BCM7XXX_SHD_MODE_2);
	if (ret < 0)
	return ret;

	return 0;
	}

	/* Workaround for putting the PHY in IDDQ mode, required
	* for all BCM7XXX 40nm and 65nm PHYs
	*/
	static int bcm7xxx_suspend(struct phy_device *phydev)
	{
	int ret;
	static const struct bcm7xxx_regs {
	int reg;
	u16 value;
	} bcm7xxx_suspend_cfg[] = {
	{ MII_BCM7XXX_TEST, 0x008b },
	{ MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 },
	{ MII_BCM7XXX_100TX_DISC, 0x7000 },
	{ MII_BCM7XXX_TEST, 0x000f },
	{ MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 },
	{ MII_BCM7XXX_TEST, 0x000b },
	};
	unsigned int i;

	for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) {
	ret = phy_write(phydev,
	bcm7xxx_suspend_cfg[i].reg,
	bcm7xxx_suspend_cfg[i].value);
	if (ret)
	return ret;
	}

	return 0;
	}

	static int bcm7xxx_28nm_get_tunable(struct phy_device *phydev,
	struct ethtool_tunable *tuna,
	void *data)
	{
	switch (tuna->id) {
	case ETHTOOL_PHY_DOWNSHIFT:
	return bcm_phy_downshift_get(phydev, (u8 *)data);
	default:
	return -EOPNOTSUPP;
	}
	}

	static int bcm7xxx_28nm_set_tunable(struct phy_device *phydev,
	struct ethtool_tunable *tuna,
	const void *data)
	{
	u8 count = (u8 )data;
	int ret;

	switch (tuna->id) {
	case ETHTOOL_PHY_DOWNSHIFT:
	ret = bcm_phy_downshift_set(phydev, count);
	break;
	default:
	return -EOPNOTSUPP;
	}

	if (ret)
	return ret;

	/* Disable EEE advertisement since this prevents the PHY
	* from successfully linking up, trigger auto-negotiation restart
	* to let the MAC decide what to do.
	*/
	ret = bcm_phy_set_eee(phydev, count == DOWNSHIFT_DEV_DISABLE);
	if (ret)
	return ret;

	return genphy_restart_aneg(phydev);
	}

	static void bcm7xxx_28nm_get_phy_stats(struct phy_device *phydev,
	struct ethtool_stats stats, u64 data)
	{
	struct bcm7xxx_phy_priv *priv = phydev->priv;

	bcm_phy_get_stats(phydev, priv->stats, stats, data);
	}

	static int bcm7xxx_28nm_probe(struct phy_device *phydev)
	{
	struct bcm7xxx_phy_priv *priv;

	priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL);
	if (!priv)
	return -ENOMEM;

	phydev->priv = priv;

	priv->stats = devm_kcalloc(&phydev->mdio.dev,
	bcm_phy_get_sset_count(phydev), sizeof(u64),
	GFP_KERNEL);
	if (!priv->stats)
	return -ENOMEM;

	return 0;
	}

	#define BCM7XXX_28NM_GPHY(_oui, _name) \
	{ \
	.phy_id = (_oui), \
	.phy_id_mask = 0xfffffff0, \
	.name = _name, \
	/* PHY_GBIT_FEATURES */ \
	.flags = PHY_IS_INTERNAL, \
	.config_init = bcm7xxx_28nm_config_init, \
	.resume = bcm7xxx_28nm_resume, \
	.get_tunable = bcm7xxx_28nm_get_tunable, \
	.set_tunable = bcm7xxx_28nm_set_tunable, \
	.get_sset_count = bcm_phy_get_sset_count, \
	.get_strings = bcm_phy_get_strings, \
	.get_stats = bcm7xxx_28nm_get_phy_stats, \
	.probe = bcm7xxx_28nm_probe, \
	}

	#define BCM7XXX_28NM_EPHY(_oui, _name) \
	{ \
	.phy_id = (_oui), \
	.phy_id_mask = 0xfffffff0, \
	.name = _name, \
	/* PHY_BASIC_FEATURES */ \
	.flags = PHY_IS_INTERNAL, \
	.config_init = bcm7xxx_28nm_ephy_config_init, \
	.resume = bcm7xxx_28nm_ephy_resume, \
	.get_sset_count = bcm_phy_get_sset_count, \
	.get_strings = bcm_phy_get_strings, \
	.get_stats = bcm7xxx_28nm_get_phy_stats, \
	.probe = bcm7xxx_28nm_probe, \
	}

	#define BCM7XXX_40NM_EPHY(_oui, _name) \
	{ \
	.phy_id = (_oui), \
	.phy_id_mask = 0xfffffff0, \
	.name = _name, \
	/* PHY_BASIC_FEATURES */ \
	.flags = PHY_IS_INTERNAL, \
	.config_init = bcm7xxx_config_init, \
	.suspend = bcm7xxx_suspend, \
	.resume = bcm7xxx_config_init, \
	}

	static struct phy_driver bcm7xxx_driver[] = {
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7250, "Broadcom BCM7250"),
	BCM7XXX_28NM_EPHY(PHY_ID_BCM7255, "Broadcom BCM7255"),
	BCM7XXX_28NM_EPHY(PHY_ID_BCM7260, "Broadcom BCM7260"),
	BCM7XXX_28NM_EPHY(PHY_ID_BCM7268, "Broadcom BCM7268"),
	BCM7XXX_28NM_EPHY(PHY_ID_BCM7271, "Broadcom BCM7271"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7278, "Broadcom BCM7278"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7364, "Broadcom BCM7364"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7366, "Broadcom BCM7366"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM74371, "Broadcom BCM74371"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7439, "Broadcom BCM7439"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7439_2, "Broadcom BCM7439 (2)"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7445, "Broadcom BCM7445"),
	BCM7XXX_40NM_EPHY(PHY_ID_BCM7346, "Broadcom BCM7346"),
	BCM7XXX_40NM_EPHY(PHY_ID_BCM7362, "Broadcom BCM7362"),
	BCM7XXX_40NM_EPHY(PHY_ID_BCM7425, "Broadcom BCM7425"),
	BCM7XXX_40NM_EPHY(PHY_ID_BCM7429, "Broadcom BCM7429"),
	BCM7XXX_40NM_EPHY(PHY_ID_BCM7435, "Broadcom BCM7435"),
	};

	static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = {
	{ PHY_ID_BCM7250, 0xfffffff0, },
	{ PHY_ID_BCM7255, 0xfffffff0, },
	{ PHY_ID_BCM7260, 0xfffffff0, },
	{ PHY_ID_BCM7268, 0xfffffff0, },
	{ PHY_ID_BCM7271, 0xfffffff0, },
	{ PHY_ID_BCM7278, 0xfffffff0, },
	{ PHY_ID_BCM7364, 0xfffffff0, },
	{ PHY_ID_BCM7366, 0xfffffff0, },
	{ PHY_ID_BCM7346, 0xfffffff0, },
	{ PHY_ID_BCM7362, 0xfffffff0, },
	{ PHY_ID_BCM7425, 0xfffffff0, },
	{ PHY_ID_BCM7429, 0xfffffff0, },
	{ PHY_ID_BCM74371, 0xfffffff0, },
	{ PHY_ID_BCM7439, 0xfffffff0, },
	{ PHY_ID_BCM7435, 0xfffffff0, },
	{ PHY_ID_BCM7445, 0xfffffff0, },
	{ }
	};

	module_phy_driver(bcm7xxx_driver);

	MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl);

	MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver");
	MODULE_LICENSE("GPL");
	MODULE_AUTHOR("Broadcom Corporation");