| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Driver for the Texas Instruments DP83867 PHY |
| * |
| * Copyright (C) 2015 Texas Instruments Inc. |
| */ |
| |
| #include <linux/ethtool.h> |
| #include <linux/kernel.h> |
| #include <linux/mii.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/phy.h> |
| #include <linux/delay.h> |
| |
| #include <dt-bindings/net/ti-dp83867.h> |
| |
| #define DP83867_PHY_ID 0x2000a231 |
| #define DP83867_DEVADDR 0x1f |
| |
| #define MII_DP83867_PHYCTRL 0x10 |
| #define MII_DP83867_MICR 0x12 |
| #define MII_DP83867_ISR 0x13 |
| #define DP83867_CTRL 0x1f |
| #define DP83867_CFG3 0x1e |
| |
| /* Extended Registers */ |
| #define DP83867_CFG4 0x0031 |
| #define DP83867_RGMIICTL 0x0032 |
| #define DP83867_STRAP_STS1 0x006E |
| #define DP83867_RGMIIDCTL 0x0086 |
| #define DP83867_IO_MUX_CFG 0x0170 |
| |
| #define DP83867_SW_RESET BIT(15) |
| #define DP83867_SW_RESTART BIT(14) |
| |
| /* MICR Interrupt bits */ |
| #define MII_DP83867_MICR_AN_ERR_INT_EN BIT(15) |
| #define MII_DP83867_MICR_SPEED_CHNG_INT_EN BIT(14) |
| #define MII_DP83867_MICR_DUP_MODE_CHNG_INT_EN BIT(13) |
| #define MII_DP83867_MICR_PAGE_RXD_INT_EN BIT(12) |
| #define MII_DP83867_MICR_AUTONEG_COMP_INT_EN BIT(11) |
| #define MII_DP83867_MICR_LINK_STS_CHNG_INT_EN BIT(10) |
| #define MII_DP83867_MICR_FALSE_CARRIER_INT_EN BIT(8) |
| #define MII_DP83867_MICR_SLEEP_MODE_CHNG_INT_EN BIT(4) |
| #define MII_DP83867_MICR_WOL_INT_EN BIT(3) |
| #define MII_DP83867_MICR_XGMII_ERR_INT_EN BIT(2) |
| #define MII_DP83867_MICR_POL_CHNG_INT_EN BIT(1) |
| #define MII_DP83867_MICR_JABBER_INT_EN BIT(0) |
| |
| /* RGMIICTL bits */ |
| #define DP83867_RGMII_TX_CLK_DELAY_EN BIT(1) |
| #define DP83867_RGMII_RX_CLK_DELAY_EN BIT(0) |
| |
| /* STRAP_STS1 bits */ |
| #define DP83867_STRAP_STS1_RESERVED BIT(11) |
| |
| /* PHY CTRL bits */ |
| #define DP83867_PHYCR_FIFO_DEPTH_SHIFT 14 |
| #define DP83867_PHYCR_FIFO_DEPTH_MASK (3 << 14) |
| #define DP83867_PHYCR_RESERVED_MASK BIT(11) |
| |
| /* RGMIIDCTL bits */ |
| #define DP83867_RGMII_TX_CLK_DELAY_SHIFT 4 |
| |
| /* IO_MUX_CFG bits */ |
| #define DP83867_IO_MUX_CFG_IO_IMPEDANCE_CTRL 0x1f |
| |
| #define DP83867_IO_MUX_CFG_IO_IMPEDANCE_MAX 0x0 |
| #define DP83867_IO_MUX_CFG_IO_IMPEDANCE_MIN 0x1f |
| #define DP83867_IO_MUX_CFG_CLK_O_SEL_MASK (0x1f << 8) |
| #define DP83867_IO_MUX_CFG_CLK_O_SEL_SHIFT 8 |
| |
| /* CFG4 bits */ |
| #define DP83867_CFG4_PORT_MIRROR_EN BIT(0) |
| |
| enum { |
| DP83867_PORT_MIRROING_KEEP, |
| DP83867_PORT_MIRROING_EN, |
| DP83867_PORT_MIRROING_DIS, |
| }; |
| |
| struct dp83867_private { |
| int rx_id_delay; |
| int tx_id_delay; |
| int fifo_depth; |
| int io_impedance; |
| int port_mirroring; |
| bool rxctrl_strap_quirk; |
| int clk_output_sel; |
| }; |
| |
| static int dp83867_ack_interrupt(struct phy_device *phydev) |
| { |
| int err = phy_read(phydev, MII_DP83867_ISR); |
| |
| if (err < 0) |
| return err; |
| |
| return 0; |
| } |
| |
| static int dp83867_config_intr(struct phy_device *phydev) |
| { |
| int micr_status; |
| |
| if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { |
| micr_status = phy_read(phydev, MII_DP83867_MICR); |
| if (micr_status < 0) |
| return micr_status; |
| |
| micr_status |= |
| (MII_DP83867_MICR_AN_ERR_INT_EN | |
| MII_DP83867_MICR_SPEED_CHNG_INT_EN | |
| MII_DP83867_MICR_AUTONEG_COMP_INT_EN | |
| MII_DP83867_MICR_LINK_STS_CHNG_INT_EN | |
| MII_DP83867_MICR_DUP_MODE_CHNG_INT_EN | |
| MII_DP83867_MICR_SLEEP_MODE_CHNG_INT_EN); |
| |
| return phy_write(phydev, MII_DP83867_MICR, micr_status); |
| } |
| |
| micr_status = 0x0; |
| return phy_write(phydev, MII_DP83867_MICR, micr_status); |
| } |
| |
| static int dp83867_config_port_mirroring(struct phy_device *phydev) |
| { |
| struct dp83867_private *dp83867 = |
| (struct dp83867_private *)phydev->priv; |
| |
| if (dp83867->port_mirroring == DP83867_PORT_MIRROING_EN) |
| phy_set_bits_mmd(phydev, DP83867_DEVADDR, DP83867_CFG4, |
| DP83867_CFG4_PORT_MIRROR_EN); |
| else |
| phy_clear_bits_mmd(phydev, DP83867_DEVADDR, DP83867_CFG4, |
| DP83867_CFG4_PORT_MIRROR_EN); |
| return 0; |
| } |
| |
| #ifdef CONFIG_OF_MDIO |
| static int dp83867_of_init(struct phy_device *phydev) |
| { |
| struct dp83867_private *dp83867 = phydev->priv; |
| struct device *dev = &phydev->mdio.dev; |
| struct device_node *of_node = dev->of_node; |
| int ret; |
| |
| if (!of_node) |
| return -ENODEV; |
| |
| dp83867->io_impedance = -EINVAL; |
| |
| /* Optional configuration */ |
| ret = of_property_read_u32(of_node, "ti,clk-output-sel", |
| &dp83867->clk_output_sel); |
| if (ret || dp83867->clk_output_sel > DP83867_CLK_O_SEL_REF_CLK) |
| /* Keep the default value if ti,clk-output-sel is not set |
| * or too high |
| */ |
| dp83867->clk_output_sel = DP83867_CLK_O_SEL_REF_CLK; |
| |
| if (of_property_read_bool(of_node, "ti,max-output-impedance")) |
| dp83867->io_impedance = DP83867_IO_MUX_CFG_IO_IMPEDANCE_MAX; |
| else if (of_property_read_bool(of_node, "ti,min-output-impedance")) |
| dp83867->io_impedance = DP83867_IO_MUX_CFG_IO_IMPEDANCE_MIN; |
| |
| dp83867->rxctrl_strap_quirk = of_property_read_bool(of_node, |
| "ti,dp83867-rxctrl-strap-quirk"); |
| |
| ret = of_property_read_u32(of_node, "ti,rx-internal-delay", |
| &dp83867->rx_id_delay); |
| if (ret && |
| (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || |
| phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID)) |
| return ret; |
| |
| ret = of_property_read_u32(of_node, "ti,tx-internal-delay", |
| &dp83867->tx_id_delay); |
| if (ret && |
| (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || |
| phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) |
| return ret; |
| |
| if (of_property_read_bool(of_node, "enet-phy-lane-swap")) |
| dp83867->port_mirroring = DP83867_PORT_MIRROING_EN; |
| |
| if (of_property_read_bool(of_node, "enet-phy-lane-no-swap")) |
| dp83867->port_mirroring = DP83867_PORT_MIRROING_DIS; |
| |
| return of_property_read_u32(of_node, "ti,fifo-depth", |
| &dp83867->fifo_depth); |
| } |
| #else |
| static int dp83867_of_init(struct phy_device *phydev) |
| { |
| return 0; |
| } |
| #endif /* CONFIG_OF_MDIO */ |
| |
| static int dp83867_config_init(struct phy_device *phydev) |
| { |
| struct dp83867_private *dp83867; |
| int ret, val, bs; |
| u16 delay; |
| |
| if (!phydev->priv) { |
| dp83867 = devm_kzalloc(&phydev->mdio.dev, sizeof(*dp83867), |
| GFP_KERNEL); |
| if (!dp83867) |
| return -ENOMEM; |
| |
| phydev->priv = dp83867; |
| ret = dp83867_of_init(phydev); |
| if (ret) |
| return ret; |
| } else { |
| dp83867 = (struct dp83867_private *)phydev->priv; |
| } |
| |
| /* RX_DV/RX_CTRL strapped in mode 1 or mode 2 workaround */ |
| if (dp83867->rxctrl_strap_quirk) |
| phy_clear_bits_mmd(phydev, DP83867_DEVADDR, DP83867_CFG4, |
| BIT(7)); |
| |
| if (phy_interface_is_rgmii(phydev)) { |
| val = phy_read(phydev, MII_DP83867_PHYCTRL); |
| if (val < 0) |
| return val; |
| val &= ~DP83867_PHYCR_FIFO_DEPTH_MASK; |
| val |= (dp83867->fifo_depth << DP83867_PHYCR_FIFO_DEPTH_SHIFT); |
| |
| /* The code below checks if "port mirroring" N/A MODE4 has been |
| * enabled during power on bootstrap. |
| * |
| * Such N/A mode enabled by mistake can put PHY IC in some |
| * internal testing mode and disable RGMII transmission. |
| * |
| * In this particular case one needs to check STRAP_STS1 |
| * register's bit 11 (marked as RESERVED). |
| */ |
| |
| bs = phy_read_mmd(phydev, DP83867_DEVADDR, DP83867_STRAP_STS1); |
| if (bs & DP83867_STRAP_STS1_RESERVED) |
| val &= ~DP83867_PHYCR_RESERVED_MASK; |
| |
| ret = phy_write(phydev, MII_DP83867_PHYCTRL, val); |
| if (ret) |
| return ret; |
| } |
| |
| if ((phydev->interface >= PHY_INTERFACE_MODE_RGMII_ID) && |
| (phydev->interface <= PHY_INTERFACE_MODE_RGMII_RXID)) { |
| val = phy_read_mmd(phydev, DP83867_DEVADDR, DP83867_RGMIICTL); |
| |
| if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) |
| val |= (DP83867_RGMII_TX_CLK_DELAY_EN | DP83867_RGMII_RX_CLK_DELAY_EN); |
| |
| if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) |
| val |= DP83867_RGMII_TX_CLK_DELAY_EN; |
| |
| if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) |
| val |= DP83867_RGMII_RX_CLK_DELAY_EN; |
| |
| phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RGMIICTL, val); |
| |
| delay = (dp83867->rx_id_delay | |
| (dp83867->tx_id_delay << DP83867_RGMII_TX_CLK_DELAY_SHIFT)); |
| |
| phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RGMIIDCTL, |
| delay); |
| |
| if (dp83867->io_impedance >= 0) |
| phy_modify_mmd(phydev, DP83867_DEVADDR, DP83867_IO_MUX_CFG, |
| DP83867_IO_MUX_CFG_IO_IMPEDANCE_CTRL, |
| dp83867->io_impedance & |
| DP83867_IO_MUX_CFG_IO_IMPEDANCE_CTRL); |
| } |
| |
| /* Enable Interrupt output INT_OE in CFG3 register */ |
| if (phy_interrupt_is_valid(phydev)) { |
| val = phy_read(phydev, DP83867_CFG3); |
| val |= BIT(7); |
| phy_write(phydev, DP83867_CFG3, val); |
| } |
| |
| if (dp83867->port_mirroring != DP83867_PORT_MIRROING_KEEP) |
| dp83867_config_port_mirroring(phydev); |
| |
| /* Clock output selection if muxing property is set */ |
| if (dp83867->clk_output_sel != DP83867_CLK_O_SEL_REF_CLK) |
| phy_modify_mmd(phydev, DP83867_DEVADDR, DP83867_IO_MUX_CFG, |
| DP83867_IO_MUX_CFG_CLK_O_SEL_MASK, |
| dp83867->clk_output_sel << |
| DP83867_IO_MUX_CFG_CLK_O_SEL_SHIFT); |
| |
| return 0; |
| } |
| |
| static int dp83867_phy_reset(struct phy_device *phydev) |
| { |
| int err; |
| |
| err = phy_write(phydev, DP83867_CTRL, DP83867_SW_RESET); |
| if (err < 0) |
| return err; |
| |
| usleep_range(10, 20); |
| |
| return dp83867_config_init(phydev); |
| } |
| |
| static struct phy_driver dp83867_driver[] = { |
| { |
| .phy_id = DP83867_PHY_ID, |
| .phy_id_mask = 0xfffffff0, |
| .name = "TI DP83867", |
| /* PHY_GBIT_FEATURES */ |
| |
| .config_init = dp83867_config_init, |
| .soft_reset = dp83867_phy_reset, |
| |
| /* IRQ related */ |
| .ack_interrupt = dp83867_ack_interrupt, |
| .config_intr = dp83867_config_intr, |
| |
| .suspend = genphy_suspend, |
| .resume = genphy_resume, |
| }, |
| }; |
| module_phy_driver(dp83867_driver); |
| |
| static struct mdio_device_id __maybe_unused dp83867_tbl[] = { |
| { DP83867_PHY_ID, 0xfffffff0 }, |
| { } |
| }; |
| |
| MODULE_DEVICE_TABLE(mdio, dp83867_tbl); |
| |
| MODULE_DESCRIPTION("Texas Instruments DP83867 PHY driver"); |
| MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com"); |
| MODULE_LICENSE("GPL v2"); |