| What: /sys/kernel/debug/habanalabs/hl<n>/addr |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Sets the device address to be used for read or write through |
| PCI bar, or the device VA of a host mapped memory to be read or |
| written directly from the host. The latter option is allowed |
| only when the IOMMU is disabled. |
| The acceptable value is a string that starts with "0x" |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/clk_gate |
| Date: May 2020 |
| KernelVersion: 5.8 |
| Contact: oded.gabbay@gmail.com |
| Description: Allow the root user to disable/enable in runtime the clock |
| gating mechanism in Gaudi. Due to how Gaudi is built, the |
| clock gating needs to be disabled in order to access the |
| registers of the TPC and MME engines. This is sometimes needed |
| during debug by the user and hence the user needs this option. |
| The user can supply a bitmask value, each bit represents |
| a different engine to disable/enable its clock gating feature. |
| The bitmask is composed of 20 bits: |
| 0 - 7 : DMA channels |
| 8 - 11 : MME engines |
| 12 - 19 : TPC engines |
| The bit's location of a specific engine can be determined |
| using (1 << GAUDI_ENGINE_ID_*). GAUDI_ENGINE_ID_* values |
| are defined in uapi habanalabs.h file in enum gaudi_engine_id |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/command_buffers |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Displays a list with information about the currently allocated |
| command buffers |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/command_submission |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Displays a list with information about the currently active |
| command submissions |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/command_submission_jobs |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Displays a list with detailed information about each JOB (CB) of |
| each active command submission |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/data32 |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Allows the root user to read or write directly through the |
| device's PCI bar. Writing to this file generates a write |
| transaction while reading from the file generates a read |
| transaction. This custom interface is needed (instead of using |
| the generic Linux user-space PCI mapping) because the DDR bar |
| is very small compared to the DDR memory and only the driver can |
| move the bar before and after the transaction. |
| If the IOMMU is disabled, it also allows the root user to read |
| or write from the host a device VA of a host mapped memory |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/data64 |
| Date: Jan 2020 |
| KernelVersion: 5.6 |
| Contact: oded.gabbay@gmail.com |
| Description: Allows the root user to read or write 64 bit data directly |
| through the device's PCI bar. Writing to this file generates a |
| write transaction while reading from the file generates a read |
| transaction. This custom interface is needed (instead of using |
| the generic Linux user-space PCI mapping) because the DDR bar |
| is very small compared to the DDR memory and only the driver can |
| move the bar before and after the transaction. |
| If the IOMMU is disabled, it also allows the root user to read |
| or write from the host a device VA of a host mapped memory |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/device |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Enables the root user to set the device to specific state. |
| Valid values are "disable", "enable", "suspend", "resume". |
| User can read this property to see the valid values |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/engines |
| Date: Jul 2019 |
| KernelVersion: 5.3 |
| Contact: oded.gabbay@gmail.com |
| Description: Displays the status registers values of the device engines and |
| their derived idle status |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/i2c_addr |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Sets I2C device address for I2C transaction that is generated |
| by the device's CPU |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/i2c_bus |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Sets I2C bus address for I2C transaction that is generated by |
| the device's CPU |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/i2c_data |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Triggers an I2C transaction that is generated by the device's |
| CPU. Writing to this file generates a write transaction while |
| reading from the file generates a read transcation |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/i2c_reg |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Sets I2C register id for I2C transaction that is generated by |
| the device's CPU |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/led0 |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Sets the state of the first S/W led on the device |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/led1 |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Sets the state of the second S/W led on the device |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/led2 |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Sets the state of the third S/W led on the device |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/mmu |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Displays the hop values and physical address for a given ASID |
| and virtual address. The user should write the ASID and VA into |
| the file and then read the file to get the result. |
| e.g. to display info about VA 0x1000 for ASID 1 you need to do: |
| echo "1 0x1000" > /sys/kernel/debug/habanalabs/hl0/mmu |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/set_power_state |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Sets the PCI power state. Valid values are "1" for D0 and "2" |
| for D3Hot |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/userptr |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Displays a list with information about the currently user |
| pointers (user virtual addresses) that are pinned and mapped |
| to DMA addresses |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/vm |
| Date: Jan 2019 |
| KernelVersion: 5.1 |
| Contact: oded.gabbay@gmail.com |
| Description: Displays a list with information about all the active virtual |
| address mappings per ASID |
| |
| What: /sys/kernel/debug/habanalabs/hl<n>/stop_on_err |
| Date: Mar 2020 |
| KernelVersion: 5.6 |
| Contact: oded.gabbay@gmail.com |
| Description: Sets the stop-on_error option for the device engines. Value of |
| "0" is for disable, otherwise enable. |
