| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Maxim MAX77714 Core Driver |
| * |
| * Copyright (C) 2022 Luca Ceresoli |
| * Author: Luca Ceresoli <luca.ceresoli@bootlin.com> |
| */ |
| |
| #include <linux/i2c.h> |
| #include <linux/interrupt.h> |
| #include <linux/mfd/core.h> |
| #include <linux/mfd/max77714.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/regmap.h> |
| |
| static const struct mfd_cell max77714_cells[] = { |
| { .name = "max77714-watchdog" }, |
| { .name = "max77714-rtc" }, |
| }; |
| |
| static const struct regmap_range max77714_readable_ranges[] = { |
| regmap_reg_range(MAX77714_INT_TOP, MAX77714_INT_TOP), |
| regmap_reg_range(MAX77714_INT_TOPM, MAX77714_INT_TOPM), |
| regmap_reg_range(MAX77714_32K_STATUS, MAX77714_32K_CONFIG), |
| regmap_reg_range(MAX77714_CNFG_GLBL2, MAX77714_CNFG2_ONOFF), |
| }; |
| |
| static const struct regmap_range max77714_writable_ranges[] = { |
| regmap_reg_range(MAX77714_INT_TOPM, MAX77714_INT_TOPM), |
| regmap_reg_range(MAX77714_32K_CONFIG, MAX77714_32K_CONFIG), |
| regmap_reg_range(MAX77714_CNFG_GLBL2, MAX77714_CNFG2_ONOFF), |
| }; |
| |
| static const struct regmap_access_table max77714_readable_table = { |
| .yes_ranges = max77714_readable_ranges, |
| .n_yes_ranges = ARRAY_SIZE(max77714_readable_ranges), |
| }; |
| |
| static const struct regmap_access_table max77714_writable_table = { |
| .yes_ranges = max77714_writable_ranges, |
| .n_yes_ranges = ARRAY_SIZE(max77714_writable_ranges), |
| }; |
| |
| static const struct regmap_config max77714_regmap_config = { |
| .reg_bits = 8, |
| .val_bits = 8, |
| .max_register = MAX77714_CNFG2_ONOFF, |
| .rd_table = &max77714_readable_table, |
| .wr_table = &max77714_writable_table, |
| }; |
| |
| static const struct regmap_irq max77714_top_irqs[] = { |
| REGMAP_IRQ_REG(MAX77714_IRQ_TOP_ONOFF, 0, MAX77714_INT_TOP_ONOFF), |
| REGMAP_IRQ_REG(MAX77714_IRQ_TOP_RTC, 0, MAX77714_INT_TOP_RTC), |
| REGMAP_IRQ_REG(MAX77714_IRQ_TOP_GPIO, 0, MAX77714_INT_TOP_GPIO), |
| REGMAP_IRQ_REG(MAX77714_IRQ_TOP_LDO, 0, MAX77714_INT_TOP_LDO), |
| REGMAP_IRQ_REG(MAX77714_IRQ_TOP_SD, 0, MAX77714_INT_TOP_SD), |
| REGMAP_IRQ_REG(MAX77714_IRQ_TOP_GLBL, 0, MAX77714_INT_TOP_GLBL), |
| }; |
| |
| static const struct regmap_irq_chip max77714_irq_chip = { |
| .name = "max77714-pmic", |
| .status_base = MAX77714_INT_TOP, |
| .mask_base = MAX77714_INT_TOPM, |
| .num_regs = 1, |
| .irqs = max77714_top_irqs, |
| .num_irqs = ARRAY_SIZE(max77714_top_irqs), |
| }; |
| |
| /* |
| * MAX77714 initially uses the internal, low precision oscillator. Enable |
| * the external oscillator by setting the XOSC_RETRY bit. If the external |
| * oscillator is not OK (probably not installed) this has no effect. |
| */ |
| static int max77714_setup_xosc(struct device *dev, struct regmap *regmap) |
| { |
| /* Internal Crystal Load Capacitance, indexed by value of 32KLOAD bits */ |
| static const unsigned int load_cap[4] = {0, 10, 12, 22}; /* pF */ |
| unsigned int load_cap_idx; |
| unsigned int status; |
| int err; |
| |
| err = regmap_update_bits(regmap, MAX77714_32K_CONFIG, |
| MAX77714_32K_CONFIG_XOSC_RETRY, |
| MAX77714_32K_CONFIG_XOSC_RETRY); |
| if (err) |
| return dev_err_probe(dev, err, "Failed to configure the external oscillator\n"); |
| |
| err = regmap_read(regmap, MAX77714_32K_STATUS, &status); |
| if (err) |
| return dev_err_probe(dev, err, "Failed to read external oscillator status\n"); |
| |
| load_cap_idx = (status >> MAX77714_32K_STATUS_32KLOAD_SHF) |
| & MAX77714_32K_STATUS_32KLOAD_MSK; |
| |
| dev_info(dev, "Using %s oscillator, %d pF load cap\n", |
| status & MAX77714_32K_STATUS_32KSOURCE ? "internal" : "external", |
| load_cap[load_cap_idx]); |
| |
| return 0; |
| } |
| |
| static int max77714_probe(struct i2c_client *client) |
| { |
| struct device *dev = &client->dev; |
| struct regmap *regmap; |
| struct regmap_irq_chip_data *irq_data; |
| int err; |
| |
| regmap = devm_regmap_init_i2c(client, &max77714_regmap_config); |
| if (IS_ERR(regmap)) |
| return dev_err_probe(dev, PTR_ERR(regmap), |
| "Failed to initialise regmap\n"); |
| |
| err = max77714_setup_xosc(dev, regmap); |
| if (err) |
| return err; |
| |
| err = devm_regmap_add_irq_chip(dev, regmap, client->irq, |
| IRQF_ONESHOT | IRQF_SHARED, 0, |
| &max77714_irq_chip, &irq_data); |
| if (err) |
| return dev_err_probe(dev, err, "Failed to add PMIC IRQ chip\n"); |
| |
| err = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE, |
| max77714_cells, ARRAY_SIZE(max77714_cells), |
| NULL, 0, NULL); |
| if (err) |
| return dev_err_probe(dev, err, "Failed to register child devices\n"); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id max77714_dt_match[] = { |
| { .compatible = "maxim,max77714" }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, max77714_dt_match); |
| |
| static struct i2c_driver max77714_driver = { |
| .driver = { |
| .name = "max77714", |
| .of_match_table = max77714_dt_match, |
| }, |
| .probe = max77714_probe, |
| }; |
| module_i2c_driver(max77714_driver); |
| |
| MODULE_DESCRIPTION("Maxim MAX77714 MFD core driver"); |
| MODULE_AUTHOR("Luca Ceresoli <luca.ceresoli@bootlin.com>"); |
| MODULE_LICENSE("GPL"); |