| /* |
| * Copyright (c) 2008-2011 Atheros Communications Inc. |
| * |
| * Permission to use, copy, modify, and/or distribute this software for any |
| * purpose with or without fee is hereby granted, provided that the above |
| * copyright notice and this permission notice appear in all copies. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
| */ |
| |
| #include <linux/export.h> |
| #include "hw.h" |
| #include "hw-ops.h" |
| #include "ar9003_phy.h" |
| #include "ar9003_mci.h" |
| #include "ar9003_aic.h" |
| |
| static void ar9003_mci_reset_req_wakeup(struct ath_hw *ah) |
| { |
| REG_RMW_FIELD(ah, AR_MCI_COMMAND2, |
| AR_MCI_COMMAND2_RESET_REQ_WAKEUP, 1); |
| udelay(1); |
| REG_RMW_FIELD(ah, AR_MCI_COMMAND2, |
| AR_MCI_COMMAND2_RESET_REQ_WAKEUP, 0); |
| } |
| |
| static int ar9003_mci_wait_for_interrupt(struct ath_hw *ah, u32 address, |
| u32 bit_position, int time_out) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| |
| while (time_out) { |
| if (!(REG_READ(ah, address) & bit_position)) { |
| udelay(10); |
| time_out -= 10; |
| |
| if (time_out < 0) |
| break; |
| else |
| continue; |
| } |
| REG_WRITE(ah, address, bit_position); |
| |
| if (address != AR_MCI_INTERRUPT_RX_MSG_RAW) |
| break; |
| |
| if (bit_position & AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE) |
| ar9003_mci_reset_req_wakeup(ah); |
| |
| if (bit_position & (AR_MCI_INTERRUPT_RX_MSG_SYS_SLEEPING | |
| AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING)) |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RAW, |
| AR_MCI_INTERRUPT_REMOTE_SLEEP_UPDATE); |
| |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RAW, AR_MCI_INTERRUPT_RX_MSG); |
| break; |
| } |
| |
| if (time_out <= 0) { |
| ath_dbg(common, MCI, |
| "MCI Wait for Reg 0x%08x = 0x%08x timeout\n", |
| address, bit_position); |
| ath_dbg(common, MCI, |
| "MCI INT_RAW = 0x%08x, RX_MSG_RAW = 0x%08x\n", |
| REG_READ(ah, AR_MCI_INTERRUPT_RAW), |
| REG_READ(ah, AR_MCI_INTERRUPT_RX_MSG_RAW)); |
| time_out = 0; |
| } |
| |
| return time_out; |
| } |
| |
| static void ar9003_mci_remote_reset(struct ath_hw *ah, bool wait_done) |
| { |
| u32 payload[4] = { 0xffffffff, 0xffffffff, 0xffffffff, 0xffffff00}; |
| |
| ar9003_mci_send_message(ah, MCI_REMOTE_RESET, 0, payload, 16, |
| wait_done, false); |
| udelay(5); |
| } |
| |
| static void ar9003_mci_send_lna_transfer(struct ath_hw *ah, bool wait_done) |
| { |
| u32 payload = 0x00000000; |
| |
| ar9003_mci_send_message(ah, MCI_LNA_TRANS, 0, &payload, 1, |
| wait_done, false); |
| } |
| |
| static void ar9003_mci_send_req_wake(struct ath_hw *ah, bool wait_done) |
| { |
| ar9003_mci_send_message(ah, MCI_REQ_WAKE, MCI_FLAG_DISABLE_TIMESTAMP, |
| NULL, 0, wait_done, false); |
| udelay(5); |
| } |
| |
| static void ar9003_mci_send_sys_waking(struct ath_hw *ah, bool wait_done) |
| { |
| ar9003_mci_send_message(ah, MCI_SYS_WAKING, MCI_FLAG_DISABLE_TIMESTAMP, |
| NULL, 0, wait_done, false); |
| } |
| |
| static void ar9003_mci_send_lna_take(struct ath_hw *ah, bool wait_done) |
| { |
| u32 payload = 0x70000000; |
| |
| ar9003_mci_send_message(ah, MCI_LNA_TAKE, 0, &payload, 1, |
| wait_done, false); |
| } |
| |
| static void ar9003_mci_send_sys_sleeping(struct ath_hw *ah, bool wait_done) |
| { |
| ar9003_mci_send_message(ah, MCI_SYS_SLEEPING, |
| MCI_FLAG_DISABLE_TIMESTAMP, |
| NULL, 0, wait_done, false); |
| } |
| |
| static void ar9003_mci_send_coex_version_query(struct ath_hw *ah, |
| bool wait_done) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 payload[4] = {0, 0, 0, 0}; |
| |
| if (mci->bt_version_known || |
| (mci->bt_state == MCI_BT_SLEEP)) |
| return; |
| |
| MCI_GPM_SET_TYPE_OPCODE(payload, MCI_GPM_COEX_AGENT, |
| MCI_GPM_COEX_VERSION_QUERY); |
| ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16, wait_done, true); |
| } |
| |
| static void ar9003_mci_send_coex_version_response(struct ath_hw *ah, |
| bool wait_done) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 payload[4] = {0, 0, 0, 0}; |
| |
| MCI_GPM_SET_TYPE_OPCODE(payload, MCI_GPM_COEX_AGENT, |
| MCI_GPM_COEX_VERSION_RESPONSE); |
| *(((u8 *)payload) + MCI_GPM_COEX_B_MAJOR_VERSION) = |
| mci->wlan_ver_major; |
| *(((u8 *)payload) + MCI_GPM_COEX_B_MINOR_VERSION) = |
| mci->wlan_ver_minor; |
| ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16, wait_done, true); |
| } |
| |
| static void ar9003_mci_send_coex_wlan_channels(struct ath_hw *ah, |
| bool wait_done) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 *payload = &mci->wlan_channels[0]; |
| |
| if (!mci->wlan_channels_update || |
| (mci->bt_state == MCI_BT_SLEEP)) |
| return; |
| |
| MCI_GPM_SET_TYPE_OPCODE(payload, MCI_GPM_COEX_AGENT, |
| MCI_GPM_COEX_WLAN_CHANNELS); |
| ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16, wait_done, true); |
| MCI_GPM_SET_TYPE_OPCODE(payload, 0xff, 0xff); |
| } |
| |
| static void ar9003_mci_send_coex_bt_status_query(struct ath_hw *ah, |
| bool wait_done, u8 query_type) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 payload[4] = {0, 0, 0, 0}; |
| bool query_btinfo; |
| |
| if (mci->bt_state == MCI_BT_SLEEP) |
| return; |
| |
| query_btinfo = !!(query_type & (MCI_GPM_COEX_QUERY_BT_ALL_INFO | |
| MCI_GPM_COEX_QUERY_BT_TOPOLOGY)); |
| MCI_GPM_SET_TYPE_OPCODE(payload, MCI_GPM_COEX_AGENT, |
| MCI_GPM_COEX_STATUS_QUERY); |
| |
| *(((u8 *)payload) + MCI_GPM_COEX_B_BT_BITMAP) = query_type; |
| |
| /* |
| * If bt_status_query message is not sent successfully, |
| * then need_flush_btinfo should be set again. |
| */ |
| if (!ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16, |
| wait_done, true)) { |
| if (query_btinfo) |
| mci->need_flush_btinfo = true; |
| } |
| |
| if (query_btinfo) |
| mci->query_bt = false; |
| } |
| |
| static void ar9003_mci_send_coex_halt_bt_gpm(struct ath_hw *ah, bool halt, |
| bool wait_done) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 payload[4] = {0, 0, 0, 0}; |
| |
| MCI_GPM_SET_TYPE_OPCODE(payload, MCI_GPM_COEX_AGENT, |
| MCI_GPM_COEX_HALT_BT_GPM); |
| |
| if (halt) { |
| mci->query_bt = true; |
| /* Send next unhalt no matter halt sent or not */ |
| mci->unhalt_bt_gpm = true; |
| mci->need_flush_btinfo = true; |
| *(((u8 *)payload) + MCI_GPM_COEX_B_HALT_STATE) = |
| MCI_GPM_COEX_BT_GPM_HALT; |
| } else |
| *(((u8 *)payload) + MCI_GPM_COEX_B_HALT_STATE) = |
| MCI_GPM_COEX_BT_GPM_UNHALT; |
| |
| ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16, wait_done, true); |
| } |
| |
| static void ar9003_mci_prep_interface(struct ath_hw *ah) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 saved_mci_int_en; |
| u32 mci_timeout = 150; |
| |
| mci->bt_state = MCI_BT_SLEEP; |
| saved_mci_int_en = REG_READ(ah, AR_MCI_INTERRUPT_EN); |
| |
| REG_WRITE(ah, AR_MCI_INTERRUPT_EN, 0); |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW, |
| REG_READ(ah, AR_MCI_INTERRUPT_RX_MSG_RAW)); |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RAW, |
| REG_READ(ah, AR_MCI_INTERRUPT_RAW)); |
| |
| ar9003_mci_remote_reset(ah, true); |
| ar9003_mci_send_req_wake(ah, true); |
| |
| if (!ar9003_mci_wait_for_interrupt(ah, AR_MCI_INTERRUPT_RX_MSG_RAW, |
| AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING, 500)) |
| goto clear_redunt; |
| |
| mci->bt_state = MCI_BT_AWAKE; |
| |
| /* |
| * we don't need to send more remote_reset at this moment. |
| * If BT receive first remote_reset, then BT HW will |
| * be cleaned up and will be able to receive req_wake |
| * and BT HW will respond sys_waking. |
| * In this case, WLAN will receive BT's HW sys_waking. |
| * Otherwise, if BT SW missed initial remote_reset, |
| * that remote_reset will still clean up BT MCI RX, |
| * and the req_wake will wake BT up, |
| * and BT SW will respond this req_wake with a remote_reset and |
| * sys_waking. In this case, WLAN will receive BT's SW |
| * sys_waking. In either case, BT's RX is cleaned up. So we |
| * don't need to reply BT's remote_reset now, if any. |
| * Similarly, if in any case, WLAN can receive BT's sys_waking, |
| * that means WLAN's RX is also fine. |
| */ |
| ar9003_mci_send_sys_waking(ah, true); |
| udelay(10); |
| |
| /* |
| * Set BT priority interrupt value to be 0xff to |
| * avoid having too many BT PRIORITY interrupts. |
| */ |
| REG_WRITE(ah, AR_MCI_BT_PRI0, 0xFFFFFFFF); |
| REG_WRITE(ah, AR_MCI_BT_PRI1, 0xFFFFFFFF); |
| REG_WRITE(ah, AR_MCI_BT_PRI2, 0xFFFFFFFF); |
| REG_WRITE(ah, AR_MCI_BT_PRI3, 0xFFFFFFFF); |
| REG_WRITE(ah, AR_MCI_BT_PRI, 0X000000FF); |
| |
| /* |
| * A contention reset will be received after send out |
| * sys_waking. Also BT priority interrupt bits will be set. |
| * Clear those bits before the next step. |
| */ |
| |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW, |
| AR_MCI_INTERRUPT_RX_MSG_CONT_RST); |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RAW, AR_MCI_INTERRUPT_BT_PRI); |
| |
| if (mci->is_2g && MCI_ANT_ARCH_PA_LNA_SHARED(mci)) { |
| ar9003_mci_send_lna_transfer(ah, true); |
| udelay(5); |
| } |
| |
| if (mci->is_2g && !mci->update_2g5g && MCI_ANT_ARCH_PA_LNA_SHARED(mci)) { |
| if (ar9003_mci_wait_for_interrupt(ah, |
| AR_MCI_INTERRUPT_RX_MSG_RAW, |
| AR_MCI_INTERRUPT_RX_MSG_LNA_INFO, |
| mci_timeout)) |
| ath_dbg(common, MCI, |
| "MCI WLAN has control over the LNA & BT obeys it\n"); |
| else |
| ath_dbg(common, MCI, |
| "MCI BT didn't respond to LNA_TRANS\n"); |
| } |
| |
| clear_redunt: |
| /* Clear the extra redundant SYS_WAKING from BT */ |
| if ((mci->bt_state == MCI_BT_AWAKE) && |
| (REG_READ_FIELD(ah, AR_MCI_INTERRUPT_RX_MSG_RAW, |
| AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING)) && |
| (REG_READ_FIELD(ah, AR_MCI_INTERRUPT_RX_MSG_RAW, |
| AR_MCI_INTERRUPT_RX_MSG_SYS_SLEEPING) == 0)) { |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW, |
| AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING); |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RAW, |
| AR_MCI_INTERRUPT_REMOTE_SLEEP_UPDATE); |
| } |
| |
| REG_WRITE(ah, AR_MCI_INTERRUPT_EN, saved_mci_int_en); |
| } |
| |
| void ar9003_mci_set_full_sleep(struct ath_hw *ah) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| if (ar9003_mci_state(ah, MCI_STATE_ENABLE) && |
| (mci->bt_state != MCI_BT_SLEEP) && |
| !mci->halted_bt_gpm) { |
| ar9003_mci_send_coex_halt_bt_gpm(ah, true, true); |
| } |
| |
| mci->ready = false; |
| } |
| |
| static void ar9003_mci_disable_interrupt(struct ath_hw *ah) |
| { |
| REG_WRITE(ah, AR_MCI_INTERRUPT_EN, 0); |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_EN, 0); |
| } |
| |
| static void ar9003_mci_enable_interrupt(struct ath_hw *ah) |
| { |
| REG_WRITE(ah, AR_MCI_INTERRUPT_EN, AR_MCI_INTERRUPT_DEFAULT); |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_EN, |
| AR_MCI_INTERRUPT_RX_MSG_DEFAULT); |
| } |
| |
| static bool ar9003_mci_check_int(struct ath_hw *ah, u32 ints) |
| { |
| u32 intr; |
| |
| intr = REG_READ(ah, AR_MCI_INTERRUPT_RX_MSG_RAW); |
| return ((intr & ints) == ints); |
| } |
| |
| void ar9003_mci_get_interrupt(struct ath_hw *ah, u32 *raw_intr, |
| u32 *rx_msg_intr) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| *raw_intr = mci->raw_intr; |
| *rx_msg_intr = mci->rx_msg_intr; |
| |
| /* Clean int bits after the values are read. */ |
| mci->raw_intr = 0; |
| mci->rx_msg_intr = 0; |
| } |
| EXPORT_SYMBOL(ar9003_mci_get_interrupt); |
| |
| void ar9003_mci_get_isr(struct ath_hw *ah, enum ath9k_int *masked) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 raw_intr, rx_msg_intr; |
| |
| rx_msg_intr = REG_READ(ah, AR_MCI_INTERRUPT_RX_MSG_RAW); |
| raw_intr = REG_READ(ah, AR_MCI_INTERRUPT_RAW); |
| |
| if ((raw_intr == 0xdeadbeef) || (rx_msg_intr == 0xdeadbeef)) { |
| ath_dbg(common, MCI, |
| "MCI gets 0xdeadbeef during int processing\n"); |
| } else { |
| mci->rx_msg_intr |= rx_msg_intr; |
| mci->raw_intr |= raw_intr; |
| *masked |= ATH9K_INT_MCI; |
| |
| if (rx_msg_intr & AR_MCI_INTERRUPT_RX_MSG_CONT_INFO) |
| mci->cont_status = REG_READ(ah, AR_MCI_CONT_STATUS); |
| |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW, rx_msg_intr); |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RAW, raw_intr); |
| } |
| } |
| |
| static void ar9003_mci_2g5g_changed(struct ath_hw *ah, bool is_2g) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| if (!mci->update_2g5g && |
| (mci->is_2g != is_2g)) |
| mci->update_2g5g = true; |
| |
| mci->is_2g = is_2g; |
| } |
| |
| static bool ar9003_mci_is_gpm_valid(struct ath_hw *ah, u32 msg_index) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 *payload; |
| u32 recv_type, offset; |
| |
| if (msg_index == MCI_GPM_INVALID) |
| return false; |
| |
| offset = msg_index << 4; |
| |
| payload = (u32 *)(mci->gpm_buf + offset); |
| recv_type = MCI_GPM_TYPE(payload); |
| |
| if (recv_type == MCI_GPM_RSVD_PATTERN) |
| return false; |
| |
| return true; |
| } |
| |
| static void ar9003_mci_observation_set_up(struct ath_hw *ah) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| if (mci->config & ATH_MCI_CONFIG_MCI_OBS_MCI) { |
| ath9k_hw_gpio_request_out(ah, 3, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_MCI_WLAN_DATA); |
| ath9k_hw_gpio_request_out(ah, 2, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_MCI_WLAN_CLK); |
| ath9k_hw_gpio_request_out(ah, 1, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_MCI_BT_DATA); |
| ath9k_hw_gpio_request_out(ah, 0, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_MCI_BT_CLK); |
| } else if (mci->config & ATH_MCI_CONFIG_MCI_OBS_TXRX) { |
| ath9k_hw_gpio_request_out(ah, 3, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_WL_IN_TX); |
| ath9k_hw_gpio_request_out(ah, 2, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_WL_IN_RX); |
| ath9k_hw_gpio_request_out(ah, 1, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_BT_IN_TX); |
| ath9k_hw_gpio_request_out(ah, 0, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_BT_IN_RX); |
| ath9k_hw_gpio_request_out(ah, 5, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_OUTPUT); |
| } else if (mci->config & ATH_MCI_CONFIG_MCI_OBS_BT) { |
| ath9k_hw_gpio_request_out(ah, 3, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_BT_IN_TX); |
| ath9k_hw_gpio_request_out(ah, 2, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_BT_IN_RX); |
| ath9k_hw_gpio_request_out(ah, 1, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_MCI_BT_DATA); |
| ath9k_hw_gpio_request_out(ah, 0, NULL, |
| AR_GPIO_OUTPUT_MUX_AS_MCI_BT_CLK); |
| } else |
| return; |
| |
| REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL(ah), AR_GPIO_JTAG_DISABLE); |
| |
| REG_RMW_FIELD(ah, AR_PHY_GLB_CONTROL, AR_GLB_DS_JTAG_DISABLE, 1); |
| REG_RMW_FIELD(ah, AR_PHY_GLB_CONTROL, AR_GLB_WLAN_UART_INTF_EN, 0); |
| REG_SET_BIT(ah, AR_GLB_GPIO_CONTROL, ATH_MCI_CONFIG_MCI_OBS_GPIO); |
| |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL2, AR_BTCOEX_CTRL2_GPIO_OBS_SEL, 0); |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL2, AR_BTCOEX_CTRL2_MAC_BB_OBS_SEL, 1); |
| REG_WRITE(ah, AR_OBS(ah), 0x4b); |
| REG_RMW_FIELD(ah, AR_DIAG_SW, AR_DIAG_OBS_PT_SEL1, 0x03); |
| REG_RMW_FIELD(ah, AR_DIAG_SW, AR_DIAG_OBS_PT_SEL2, 0x01); |
| REG_RMW_FIELD(ah, AR_MACMISC, AR_MACMISC_MISC_OBS_BUS_LSB, 0x02); |
| REG_RMW_FIELD(ah, AR_MACMISC, AR_MACMISC_MISC_OBS_BUS_MSB, 0x03); |
| REG_RMW_FIELD(ah, AR_PHY_TEST_CTL_STATUS(ah), |
| AR_PHY_TEST_CTL_DEBUGPORT_SEL, 0x07); |
| } |
| |
| static bool ar9003_mci_send_coex_bt_flags(struct ath_hw *ah, bool wait_done, |
| u8 opcode, u32 bt_flags) |
| { |
| u32 pld[4] = {0, 0, 0, 0}; |
| |
| MCI_GPM_SET_TYPE_OPCODE(pld, MCI_GPM_COEX_AGENT, |
| MCI_GPM_COEX_BT_UPDATE_FLAGS); |
| |
| *(((u8 *)pld) + MCI_GPM_COEX_B_BT_FLAGS_OP) = opcode; |
| *(((u8 *)pld) + MCI_GPM_COEX_W_BT_FLAGS + 0) = bt_flags & 0xFF; |
| *(((u8 *)pld) + MCI_GPM_COEX_W_BT_FLAGS + 1) = (bt_flags >> 8) & 0xFF; |
| *(((u8 *)pld) + MCI_GPM_COEX_W_BT_FLAGS + 2) = (bt_flags >> 16) & 0xFF; |
| *(((u8 *)pld) + MCI_GPM_COEX_W_BT_FLAGS + 3) = (bt_flags >> 24) & 0xFF; |
| |
| return ar9003_mci_send_message(ah, MCI_GPM, 0, pld, 16, |
| wait_done, true); |
| } |
| |
| static void ar9003_mci_sync_bt_state(struct ath_hw *ah) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 cur_bt_state; |
| |
| cur_bt_state = ar9003_mci_state(ah, MCI_STATE_REMOTE_SLEEP); |
| |
| if (mci->bt_state != cur_bt_state) |
| mci->bt_state = cur_bt_state; |
| |
| if (mci->bt_state != MCI_BT_SLEEP) { |
| |
| ar9003_mci_send_coex_version_query(ah, true); |
| ar9003_mci_send_coex_wlan_channels(ah, true); |
| |
| if (mci->unhalt_bt_gpm == true) |
| ar9003_mci_send_coex_halt_bt_gpm(ah, false, true); |
| } |
| } |
| |
| void ar9003_mci_check_bt(struct ath_hw *ah) |
| { |
| struct ath9k_hw_mci *mci_hw = &ah->btcoex_hw.mci; |
| |
| if (!mci_hw->ready) |
| return; |
| |
| /* |
| * check BT state again to make |
| * sure it's not changed. |
| */ |
| ar9003_mci_sync_bt_state(ah); |
| ar9003_mci_2g5g_switch(ah, true); |
| |
| if ((mci_hw->bt_state == MCI_BT_AWAKE) && |
| (mci_hw->query_bt == true)) { |
| mci_hw->need_flush_btinfo = true; |
| } |
| } |
| |
| static void ar9003_mci_process_gpm_extra(struct ath_hw *ah, u8 gpm_type, |
| u8 gpm_opcode, u32 *p_gpm) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u8 *p_data = (u8 *) p_gpm; |
| |
| if (gpm_type != MCI_GPM_COEX_AGENT) |
| return; |
| |
| switch (gpm_opcode) { |
| case MCI_GPM_COEX_VERSION_QUERY: |
| ath_dbg(common, MCI, "MCI Recv GPM COEX Version Query\n"); |
| ar9003_mci_send_coex_version_response(ah, true); |
| break; |
| case MCI_GPM_COEX_VERSION_RESPONSE: |
| ath_dbg(common, MCI, "MCI Recv GPM COEX Version Response\n"); |
| mci->bt_ver_major = |
| *(p_data + MCI_GPM_COEX_B_MAJOR_VERSION); |
| mci->bt_ver_minor = |
| *(p_data + MCI_GPM_COEX_B_MINOR_VERSION); |
| mci->bt_version_known = true; |
| ath_dbg(common, MCI, "MCI BT Coex version: %d.%d\n", |
| mci->bt_ver_major, mci->bt_ver_minor); |
| break; |
| case MCI_GPM_COEX_STATUS_QUERY: |
| ath_dbg(common, MCI, |
| "MCI Recv GPM COEX Status Query = 0x%02X\n", |
| *(p_data + MCI_GPM_COEX_B_WLAN_BITMAP)); |
| mci->wlan_channels_update = true; |
| ar9003_mci_send_coex_wlan_channels(ah, true); |
| break; |
| case MCI_GPM_COEX_BT_PROFILE_INFO: |
| mci->query_bt = true; |
| ath_dbg(common, MCI, "MCI Recv GPM COEX BT_Profile_Info\n"); |
| break; |
| case MCI_GPM_COEX_BT_STATUS_UPDATE: |
| mci->query_bt = true; |
| ath_dbg(common, MCI, |
| "MCI Recv GPM COEX BT_Status_Update SEQ=%d (drop&query)\n", |
| *(p_gpm + 3)); |
| break; |
| default: |
| break; |
| } |
| } |
| |
| static u32 ar9003_mci_wait_for_gpm(struct ath_hw *ah, u8 gpm_type, |
| u8 gpm_opcode, int time_out) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 *p_gpm = NULL, more_data; |
| u32 offset; |
| u8 recv_type = 0, recv_opcode = 0; |
| bool b_is_bt_cal_done = (gpm_type == MCI_GPM_BT_CAL_DONE); |
| |
| more_data = time_out ? MCI_GPM_NOMORE : MCI_GPM_MORE; |
| |
| while (time_out > 0) { |
| if (p_gpm) { |
| MCI_GPM_RECYCLE(p_gpm); |
| p_gpm = NULL; |
| } |
| |
| if (more_data != MCI_GPM_MORE) |
| time_out = ar9003_mci_wait_for_interrupt(ah, |
| AR_MCI_INTERRUPT_RX_MSG_RAW, |
| AR_MCI_INTERRUPT_RX_MSG_GPM, |
| time_out); |
| |
| if (!time_out) |
| break; |
| |
| offset = ar9003_mci_get_next_gpm_offset(ah, &more_data); |
| |
| if (offset == MCI_GPM_INVALID) |
| continue; |
| |
| p_gpm = (u32 *) (mci->gpm_buf + offset); |
| recv_type = MCI_GPM_TYPE(p_gpm); |
| recv_opcode = MCI_GPM_OPCODE(p_gpm); |
| |
| if (MCI_GPM_IS_CAL_TYPE(recv_type)) { |
| if (recv_type == gpm_type) { |
| if ((gpm_type == MCI_GPM_BT_CAL_DONE) && |
| !b_is_bt_cal_done) { |
| gpm_type = MCI_GPM_BT_CAL_GRANT; |
| continue; |
| } |
| break; |
| } |
| } else if ((recv_type == gpm_type) && |
| (recv_opcode == gpm_opcode)) |
| break; |
| |
| /* |
| * check if it's cal_grant |
| * |
| * When we're waiting for cal_grant in reset routine, |
| * it's possible that BT sends out cal_request at the |
| * same time. Since BT's calibration doesn't happen |
| * that often, we'll let BT completes calibration then |
| * we continue to wait for cal_grant from BT. |
| * Orginal: Wait BT_CAL_GRANT. |
| * New: Receive BT_CAL_REQ -> send WLAN_CAL_GRANT->wait |
| * BT_CAL_DONE -> Wait BT_CAL_GRANT. |
| */ |
| |
| if ((gpm_type == MCI_GPM_BT_CAL_GRANT) && |
| (recv_type == MCI_GPM_BT_CAL_REQ)) { |
| |
| u32 payload[4] = {0, 0, 0, 0}; |
| |
| gpm_type = MCI_GPM_BT_CAL_DONE; |
| MCI_GPM_SET_CAL_TYPE(payload, |
| MCI_GPM_WLAN_CAL_GRANT); |
| ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16, |
| false, false); |
| continue; |
| } else { |
| ath_dbg(common, MCI, "MCI GPM subtype not match 0x%x\n", |
| *(p_gpm + 1)); |
| ar9003_mci_process_gpm_extra(ah, recv_type, |
| recv_opcode, p_gpm); |
| } |
| } |
| |
| if (p_gpm) { |
| MCI_GPM_RECYCLE(p_gpm); |
| p_gpm = NULL; |
| } |
| |
| if (time_out <= 0) |
| time_out = 0; |
| |
| while (more_data == MCI_GPM_MORE) { |
| offset = ar9003_mci_get_next_gpm_offset(ah, &more_data); |
| if (offset == MCI_GPM_INVALID) |
| break; |
| |
| p_gpm = (u32 *) (mci->gpm_buf + offset); |
| recv_type = MCI_GPM_TYPE(p_gpm); |
| recv_opcode = MCI_GPM_OPCODE(p_gpm); |
| |
| if (!MCI_GPM_IS_CAL_TYPE(recv_type)) |
| ar9003_mci_process_gpm_extra(ah, recv_type, |
| recv_opcode, p_gpm); |
| |
| MCI_GPM_RECYCLE(p_gpm); |
| } |
| |
| return time_out; |
| } |
| |
| bool ar9003_mci_start_reset(struct ath_hw *ah, struct ath9k_channel *chan) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| struct ath9k_hw_mci *mci_hw = &ah->btcoex_hw.mci; |
| u32 payload[4] = {0, 0, 0, 0}; |
| |
| ar9003_mci_2g5g_changed(ah, IS_CHAN_2GHZ(chan)); |
| |
| if (mci_hw->bt_state != MCI_BT_CAL_START) |
| return false; |
| |
| mci_hw->bt_state = MCI_BT_CAL; |
| |
| /* |
| * MCI FIX: disable mci interrupt here. This is to avoid |
| * SW_MSG_DONE or RX_MSG bits to trigger MCI_INT and |
| * lead to mci_intr reentry. |
| */ |
| ar9003_mci_disable_interrupt(ah); |
| |
| MCI_GPM_SET_CAL_TYPE(payload, MCI_GPM_WLAN_CAL_GRANT); |
| ar9003_mci_send_message(ah, MCI_GPM, 0, payload, |
| 16, true, false); |
| |
| /* Wait BT calibration to be completed for 25ms */ |
| |
| if (ar9003_mci_wait_for_gpm(ah, MCI_GPM_BT_CAL_DONE, |
| 0, 25000)) |
| ath_dbg(common, MCI, "MCI BT_CAL_DONE received\n"); |
| else |
| ath_dbg(common, MCI, |
| "MCI BT_CAL_DONE not received\n"); |
| |
| mci_hw->bt_state = MCI_BT_AWAKE; |
| /* MCI FIX: enable mci interrupt here */ |
| ar9003_mci_enable_interrupt(ah); |
| |
| return true; |
| } |
| |
| int ar9003_mci_end_reset(struct ath_hw *ah, struct ath9k_channel *chan, |
| struct ath9k_hw_cal_data *caldata) |
| { |
| struct ath9k_hw_mci *mci_hw = &ah->btcoex_hw.mci; |
| |
| if (!mci_hw->ready) |
| return 0; |
| |
| if (!IS_CHAN_2GHZ(chan) || (mci_hw->bt_state != MCI_BT_SLEEP)) |
| goto exit; |
| |
| if (!ar9003_mci_check_int(ah, AR_MCI_INTERRUPT_RX_MSG_REMOTE_RESET) && |
| !ar9003_mci_check_int(ah, AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE)) |
| goto exit; |
| |
| /* |
| * BT is sleeping. Check if BT wakes up during |
| * WLAN calibration. If BT wakes up during |
| * WLAN calibration, need to go through all |
| * message exchanges again and recal. |
| */ |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW, |
| (AR_MCI_INTERRUPT_RX_MSG_REMOTE_RESET | |
| AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE)); |
| |
| ar9003_mci_remote_reset(ah, true); |
| ar9003_mci_send_sys_waking(ah, true); |
| udelay(1); |
| |
| if (IS_CHAN_2GHZ(chan)) |
| ar9003_mci_send_lna_transfer(ah, true); |
| |
| mci_hw->bt_state = MCI_BT_AWAKE; |
| |
| REG_CLR_BIT(ah, AR_PHY_TIMING4, |
| 1 << AR_PHY_TIMING_CONTROL4_DO_GAIN_DC_IQ_CAL_SHIFT); |
| |
| if (caldata) { |
| clear_bit(TXIQCAL_DONE, &caldata->cal_flags); |
| clear_bit(TXCLCAL_DONE, &caldata->cal_flags); |
| clear_bit(RTT_DONE, &caldata->cal_flags); |
| } |
| |
| if (!ath9k_hw_init_cal(ah, chan)) |
| return -EIO; |
| |
| REG_SET_BIT(ah, AR_PHY_TIMING4, |
| 1 << AR_PHY_TIMING_CONTROL4_DO_GAIN_DC_IQ_CAL_SHIFT); |
| |
| exit: |
| ar9003_mci_enable_interrupt(ah); |
| return 0; |
| } |
| |
| static void ar9003_mci_mute_bt(struct ath_hw *ah) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| /* disable all MCI messages */ |
| REG_WRITE(ah, AR_MCI_MSG_ATTRIBUTES_TABLE, 0xffff0000); |
| REG_WRITE(ah, AR_BTCOEX_WL_WEIGHTS0, 0xffffffff); |
| REG_WRITE(ah, AR_BTCOEX_WL_WEIGHTS1, 0xffffffff); |
| REG_WRITE(ah, AR_BTCOEX_WL_WEIGHTS2, 0xffffffff); |
| REG_WRITE(ah, AR_BTCOEX_WL_WEIGHTS3, 0xffffffff); |
| REG_SET_BIT(ah, AR_MCI_TX_CTRL, AR_MCI_TX_CTRL_DISABLE_LNA_UPDATE); |
| |
| /* wait pending HW messages to flush out */ |
| udelay(10); |
| |
| /* |
| * Send LNA_TAKE and SYS_SLEEPING when |
| * 1. reset not after resuming from full sleep |
| * 2. before reset MCI RX, to quiet BT and avoid MCI RX misalignment |
| */ |
| if (MCI_ANT_ARCH_PA_LNA_SHARED(mci)) { |
| ar9003_mci_send_lna_take(ah, true); |
| udelay(5); |
| } |
| |
| ar9003_mci_send_sys_sleeping(ah, true); |
| } |
| |
| static void ar9003_mci_osla_setup(struct ath_hw *ah, bool enable) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 thresh; |
| |
| if (!enable) { |
| REG_CLR_BIT(ah, AR_BTCOEX_CTRL, |
| AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN); |
| return; |
| } |
| REG_RMW_FIELD(ah, AR_MCI_SCHD_TABLE_2, AR_MCI_SCHD_TABLE_2_HW_BASED, 1); |
| REG_RMW_FIELD(ah, AR_MCI_SCHD_TABLE_2, |
| AR_MCI_SCHD_TABLE_2_MEM_BASED, 1); |
| |
| if (AR_SREV_9565(ah)) |
| REG_RMW_FIELD(ah, AR_MCI_MISC, AR_MCI_MISC_HW_FIX_EN, 1); |
| |
| if (!(mci->config & ATH_MCI_CONFIG_DISABLE_AGGR_THRESH)) { |
| thresh = MS(mci->config, ATH_MCI_CONFIG_AGGR_THRESH); |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL, |
| AR_BTCOEX_CTRL_AGGR_THRESH, thresh); |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL, |
| AR_BTCOEX_CTRL_TIME_TO_NEXT_BT_THRESH_EN, 1); |
| } else |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL, |
| AR_BTCOEX_CTRL_TIME_TO_NEXT_BT_THRESH_EN, 0); |
| |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL, |
| AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN, 1); |
| } |
| |
| static void ar9003_mci_stat_setup(struct ath_hw *ah) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| if (!AR_SREV_9565(ah)) |
| return; |
| |
| if (mci->config & ATH_MCI_CONFIG_MCI_STAT_DBG) { |
| REG_RMW_FIELD(ah, AR_MCI_DBG_CNT_CTRL, |
| AR_MCI_DBG_CNT_CTRL_ENABLE, 1); |
| REG_RMW_FIELD(ah, AR_MCI_DBG_CNT_CTRL, |
| AR_MCI_DBG_CNT_CTRL_BT_LINKID, |
| MCI_STAT_ALL_BT_LINKID); |
| } else { |
| REG_RMW_FIELD(ah, AR_MCI_DBG_CNT_CTRL, |
| AR_MCI_DBG_CNT_CTRL_ENABLE, 0); |
| } |
| } |
| |
| static void ar9003_mci_set_btcoex_ctrl_9565_1ANT(struct ath_hw *ah) |
| { |
| u32 regval; |
| |
| regval = SM(1, AR_BTCOEX_CTRL_AR9462_MODE) | |
| SM(1, AR_BTCOEX_CTRL_WBTIMER_EN) | |
| SM(1, AR_BTCOEX_CTRL_PA_SHARED) | |
| SM(1, AR_BTCOEX_CTRL_LNA_SHARED) | |
| SM(1, AR_BTCOEX_CTRL_NUM_ANTENNAS) | |
| SM(1, AR_BTCOEX_CTRL_RX_CHAIN_MASK) | |
| SM(0, AR_BTCOEX_CTRL_1_CHAIN_ACK) | |
| SM(0, AR_BTCOEX_CTRL_1_CHAIN_BCN) | |
| SM(0, AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN); |
| |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL2, |
| AR_BTCOEX_CTRL2_TX_CHAIN_MASK, 0x1); |
| REG_WRITE(ah, AR_BTCOEX_CTRL, regval); |
| } |
| |
| static void ar9003_mci_set_btcoex_ctrl_9565_2ANT(struct ath_hw *ah) |
| { |
| u32 regval; |
| |
| regval = SM(1, AR_BTCOEX_CTRL_AR9462_MODE) | |
| SM(1, AR_BTCOEX_CTRL_WBTIMER_EN) | |
| SM(0, AR_BTCOEX_CTRL_PA_SHARED) | |
| SM(0, AR_BTCOEX_CTRL_LNA_SHARED) | |
| SM(2, AR_BTCOEX_CTRL_NUM_ANTENNAS) | |
| SM(1, AR_BTCOEX_CTRL_RX_CHAIN_MASK) | |
| SM(0, AR_BTCOEX_CTRL_1_CHAIN_ACK) | |
| SM(0, AR_BTCOEX_CTRL_1_CHAIN_BCN) | |
| SM(0, AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN); |
| |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL2, |
| AR_BTCOEX_CTRL2_TX_CHAIN_MASK, 0x0); |
| REG_WRITE(ah, AR_BTCOEX_CTRL, regval); |
| } |
| |
| static void ar9003_mci_set_btcoex_ctrl_9462(struct ath_hw *ah) |
| { |
| u32 regval; |
| |
| regval = SM(1, AR_BTCOEX_CTRL_AR9462_MODE) | |
| SM(1, AR_BTCOEX_CTRL_WBTIMER_EN) | |
| SM(1, AR_BTCOEX_CTRL_PA_SHARED) | |
| SM(1, AR_BTCOEX_CTRL_LNA_SHARED) | |
| SM(2, AR_BTCOEX_CTRL_NUM_ANTENNAS) | |
| SM(3, AR_BTCOEX_CTRL_RX_CHAIN_MASK) | |
| SM(0, AR_BTCOEX_CTRL_1_CHAIN_ACK) | |
| SM(0, AR_BTCOEX_CTRL_1_CHAIN_BCN) | |
| SM(0, AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN); |
| |
| REG_WRITE(ah, AR_BTCOEX_CTRL, regval); |
| } |
| |
| int ar9003_mci_reset(struct ath_hw *ah, bool en_int, bool is_2g, |
| bool is_full_sleep) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 regval, i; |
| |
| ath_dbg(common, MCI, "MCI Reset (full_sleep = %d, is_2g = %d)\n", |
| is_full_sleep, is_2g); |
| |
| if (REG_READ(ah, AR_BTCOEX_CTRL) == 0xdeadbeef) { |
| ath_err(common, "BTCOEX control register is dead\n"); |
| return -EINVAL; |
| } |
| |
| /* Program MCI DMA related registers */ |
| REG_WRITE(ah, AR_MCI_GPM_0, mci->gpm_addr); |
| REG_WRITE(ah, AR_MCI_GPM_1, mci->gpm_len); |
| REG_WRITE(ah, AR_MCI_SCHD_TABLE_0, mci->sched_addr); |
| |
| /* |
| * To avoid MCI state machine be affected by incoming remote MCI msgs, |
| * MCI mode will be enabled later, right before reset the MCI TX and RX. |
| */ |
| if (AR_SREV_9565(ah)) { |
| u8 ant = MS(mci->config, ATH_MCI_CONFIG_ANT_ARCH); |
| |
| if (ant == ATH_MCI_ANT_ARCH_1_ANT_PA_LNA_SHARED) |
| ar9003_mci_set_btcoex_ctrl_9565_1ANT(ah); |
| else |
| ar9003_mci_set_btcoex_ctrl_9565_2ANT(ah); |
| } else { |
| ar9003_mci_set_btcoex_ctrl_9462(ah); |
| } |
| |
| if (is_2g && !(mci->config & ATH_MCI_CONFIG_DISABLE_OSLA)) |
| ar9003_mci_osla_setup(ah, true); |
| else |
| ar9003_mci_osla_setup(ah, false); |
| |
| REG_SET_BIT(ah, AR_PHY_GLB_CONTROL, |
| AR_BTCOEX_CTRL_SPDT_ENABLE); |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL3, |
| AR_BTCOEX_CTRL3_CONT_INFO_TIMEOUT, 20); |
| |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL2, AR_BTCOEX_CTRL2_RX_DEWEIGHT, 0); |
| REG_RMW_FIELD(ah, AR_PCU_MISC, AR_PCU_BT_ANT_PREVENT_RX, 0); |
| |
| /* Set the time out to 3.125ms (5 BT slots) */ |
| REG_RMW_FIELD(ah, AR_BTCOEX_WL_LNA, AR_BTCOEX_WL_LNA_TIMEOUT, 0x3D090); |
| |
| /* concurrent tx priority */ |
| if (mci->config & ATH_MCI_CONFIG_CONCUR_TX) { |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL2, |
| AR_BTCOEX_CTRL2_DESC_BASED_TXPWR_ENABLE, 0); |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL2, |
| AR_BTCOEX_CTRL2_TXPWR_THRESH, 0x7f); |
| REG_RMW_FIELD(ah, AR_BTCOEX_CTRL, |
| AR_BTCOEX_CTRL_REDUCE_TXPWR, 0); |
| for (i = 0; i < 8; i++) |
| REG_WRITE(ah, AR_BTCOEX_MAX_TXPWR(i), 0x7f7f7f7f); |
| } |
| |
| regval = MS(mci->config, ATH_MCI_CONFIG_CLK_DIV); |
| REG_RMW_FIELD(ah, AR_MCI_TX_CTRL, AR_MCI_TX_CTRL_CLK_DIV, regval); |
| REG_SET_BIT(ah, AR_BTCOEX_CTRL, AR_BTCOEX_CTRL_MCI_MODE_EN); |
| |
| /* Resetting the Rx and Tx paths of MCI */ |
| regval = REG_READ(ah, AR_MCI_COMMAND2); |
| regval |= SM(1, AR_MCI_COMMAND2_RESET_TX); |
| REG_WRITE(ah, AR_MCI_COMMAND2, regval); |
| |
| udelay(1); |
| |
| regval &= ~SM(1, AR_MCI_COMMAND2_RESET_TX); |
| REG_WRITE(ah, AR_MCI_COMMAND2, regval); |
| |
| if (is_full_sleep) { |
| ar9003_mci_mute_bt(ah); |
| udelay(100); |
| } |
| |
| /* Check pending GPM msg before MCI Reset Rx */ |
| ar9003_mci_check_gpm_offset(ah); |
| |
| regval |= SM(1, AR_MCI_COMMAND2_RESET_RX); |
| REG_WRITE(ah, AR_MCI_COMMAND2, regval); |
| udelay(1); |
| regval &= ~SM(1, AR_MCI_COMMAND2_RESET_RX); |
| REG_WRITE(ah, AR_MCI_COMMAND2, regval); |
| |
| /* Init GPM offset after MCI Reset Rx */ |
| ar9003_mci_state(ah, MCI_STATE_INIT_GPM_OFFSET); |
| |
| REG_WRITE(ah, AR_MCI_MSG_ATTRIBUTES_TABLE, |
| (SM(0xe801, AR_MCI_MSG_ATTRIBUTES_TABLE_INVALID_HDR) | |
| SM(0x0000, AR_MCI_MSG_ATTRIBUTES_TABLE_CHECKSUM))); |
| |
| if (MCI_ANT_ARCH_PA_LNA_SHARED(mci)) |
| REG_CLR_BIT(ah, AR_MCI_TX_CTRL, |
| AR_MCI_TX_CTRL_DISABLE_LNA_UPDATE); |
| else |
| REG_SET_BIT(ah, AR_MCI_TX_CTRL, |
| AR_MCI_TX_CTRL_DISABLE_LNA_UPDATE); |
| |
| ar9003_mci_observation_set_up(ah); |
| |
| mci->ready = true; |
| ar9003_mci_prep_interface(ah); |
| ar9003_mci_stat_setup(ah); |
| |
| if (en_int) |
| ar9003_mci_enable_interrupt(ah); |
| |
| if (ath9k_hw_is_aic_enabled(ah)) |
| ar9003_aic_start_normal(ah); |
| |
| return 0; |
| } |
| |
| void ar9003_mci_stop_bt(struct ath_hw *ah, bool save_fullsleep) |
| { |
| struct ath9k_hw_mci *mci_hw = &ah->btcoex_hw.mci; |
| |
| ar9003_mci_disable_interrupt(ah); |
| |
| if (mci_hw->ready && !save_fullsleep) { |
| ar9003_mci_mute_bt(ah); |
| udelay(20); |
| REG_WRITE(ah, AR_BTCOEX_CTRL, 0); |
| } |
| |
| mci_hw->bt_state = MCI_BT_SLEEP; |
| mci_hw->ready = false; |
| } |
| |
| static void ar9003_mci_send_2g5g_status(struct ath_hw *ah, bool wait_done) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 to_set, to_clear; |
| |
| if (!mci->update_2g5g || (mci->bt_state == MCI_BT_SLEEP)) |
| return; |
| |
| if (mci->is_2g) { |
| to_clear = MCI_2G_FLAGS_CLEAR_MASK; |
| to_set = MCI_2G_FLAGS_SET_MASK; |
| } else { |
| to_clear = MCI_5G_FLAGS_CLEAR_MASK; |
| to_set = MCI_5G_FLAGS_SET_MASK; |
| } |
| |
| if (to_clear) |
| ar9003_mci_send_coex_bt_flags(ah, wait_done, |
| MCI_GPM_COEX_BT_FLAGS_CLEAR, |
| to_clear); |
| if (to_set) |
| ar9003_mci_send_coex_bt_flags(ah, wait_done, |
| MCI_GPM_COEX_BT_FLAGS_SET, |
| to_set); |
| } |
| |
| static void ar9003_mci_queue_unsent_gpm(struct ath_hw *ah, u8 header, |
| u32 *payload, bool queue) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u8 type, opcode; |
| |
| /* check if the message is to be queued */ |
| if (header != MCI_GPM) |
| return; |
| |
| type = MCI_GPM_TYPE(payload); |
| opcode = MCI_GPM_OPCODE(payload); |
| |
| if (type != MCI_GPM_COEX_AGENT) |
| return; |
| |
| switch (opcode) { |
| case MCI_GPM_COEX_BT_UPDATE_FLAGS: |
| if (*(((u8 *)payload) + MCI_GPM_COEX_B_BT_FLAGS_OP) == |
| MCI_GPM_COEX_BT_FLAGS_READ) |
| break; |
| |
| mci->update_2g5g = queue; |
| |
| break; |
| case MCI_GPM_COEX_WLAN_CHANNELS: |
| mci->wlan_channels_update = queue; |
| break; |
| case MCI_GPM_COEX_HALT_BT_GPM: |
| if (*(((u8 *)payload) + MCI_GPM_COEX_B_HALT_STATE) == |
| MCI_GPM_COEX_BT_GPM_UNHALT) { |
| mci->unhalt_bt_gpm = queue; |
| |
| if (!queue) |
| mci->halted_bt_gpm = false; |
| } |
| |
| if (*(((u8 *)payload) + MCI_GPM_COEX_B_HALT_STATE) == |
| MCI_GPM_COEX_BT_GPM_HALT) { |
| |
| mci->halted_bt_gpm = !queue; |
| } |
| |
| break; |
| default: |
| break; |
| } |
| } |
| |
| void ar9003_mci_2g5g_switch(struct ath_hw *ah, bool force) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| if (!mci->update_2g5g && !force) |
| return; |
| |
| if (mci->is_2g) { |
| ar9003_mci_send_2g5g_status(ah, true); |
| ar9003_mci_send_lna_transfer(ah, true); |
| udelay(5); |
| |
| REG_CLR_BIT(ah, AR_MCI_TX_CTRL, |
| AR_MCI_TX_CTRL_DISABLE_LNA_UPDATE); |
| REG_CLR_BIT(ah, AR_PHY_GLB_CONTROL, |
| AR_BTCOEX_CTRL_BT_OWN_SPDT_CTRL); |
| |
| if (!(mci->config & ATH_MCI_CONFIG_DISABLE_OSLA)) |
| ar9003_mci_osla_setup(ah, true); |
| |
| if (AR_SREV_9462(ah)) |
| REG_WRITE(ah, AR_SELFGEN_MASK, 0x02); |
| } else { |
| ar9003_mci_send_lna_take(ah, true); |
| udelay(5); |
| |
| REG_SET_BIT(ah, AR_MCI_TX_CTRL, |
| AR_MCI_TX_CTRL_DISABLE_LNA_UPDATE); |
| REG_SET_BIT(ah, AR_PHY_GLB_CONTROL, |
| AR_BTCOEX_CTRL_BT_OWN_SPDT_CTRL); |
| |
| ar9003_mci_osla_setup(ah, false); |
| ar9003_mci_send_2g5g_status(ah, true); |
| } |
| } |
| |
| bool ar9003_mci_send_message(struct ath_hw *ah, u8 header, u32 flag, |
| u32 *payload, u8 len, bool wait_done, |
| bool check_bt) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| bool msg_sent = false; |
| u32 regval; |
| u32 saved_mci_int_en; |
| int i; |
| |
| saved_mci_int_en = REG_READ(ah, AR_MCI_INTERRUPT_EN); |
| regval = REG_READ(ah, AR_BTCOEX_CTRL); |
| |
| if ((regval == 0xdeadbeef) || !(regval & AR_BTCOEX_CTRL_MCI_MODE_EN)) { |
| ath_dbg(common, MCI, |
| "MCI Not sending 0x%x. MCI is not enabled. full_sleep = %d\n", |
| header, (ah->power_mode == ATH9K_PM_FULL_SLEEP) ? 1 : 0); |
| ar9003_mci_queue_unsent_gpm(ah, header, payload, true); |
| return false; |
| } else if (check_bt && (mci->bt_state == MCI_BT_SLEEP)) { |
| ath_dbg(common, MCI, |
| "MCI Don't send message 0x%x. BT is in sleep state\n", |
| header); |
| ar9003_mci_queue_unsent_gpm(ah, header, payload, true); |
| return false; |
| } |
| |
| if (wait_done) |
| REG_WRITE(ah, AR_MCI_INTERRUPT_EN, 0); |
| |
| /* Need to clear SW_MSG_DONE raw bit before wait */ |
| |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RAW, |
| (AR_MCI_INTERRUPT_SW_MSG_DONE | |
| AR_MCI_INTERRUPT_MSG_FAIL_MASK)); |
| |
| if (payload) { |
| for (i = 0; (i * 4) < len; i++) |
| REG_WRITE(ah, (AR_MCI_TX_PAYLOAD0 + i * 4), |
| *(payload + i)); |
| } |
| |
| REG_WRITE(ah, AR_MCI_COMMAND0, |
| (SM((flag & MCI_FLAG_DISABLE_TIMESTAMP), |
| AR_MCI_COMMAND0_DISABLE_TIMESTAMP) | |
| SM(len, AR_MCI_COMMAND0_LEN) | |
| SM(header, AR_MCI_COMMAND0_HEADER))); |
| |
| if (wait_done && |
| !(ar9003_mci_wait_for_interrupt(ah, AR_MCI_INTERRUPT_RAW, |
| AR_MCI_INTERRUPT_SW_MSG_DONE, 500))) |
| ar9003_mci_queue_unsent_gpm(ah, header, payload, true); |
| else { |
| ar9003_mci_queue_unsent_gpm(ah, header, payload, false); |
| msg_sent = true; |
| } |
| |
| if (wait_done) |
| REG_WRITE(ah, AR_MCI_INTERRUPT_EN, saved_mci_int_en); |
| |
| return msg_sent; |
| } |
| EXPORT_SYMBOL(ar9003_mci_send_message); |
| |
| void ar9003_mci_init_cal_req(struct ath_hw *ah, bool *is_reusable) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| struct ath9k_hw_mci *mci_hw = &ah->btcoex_hw.mci; |
| u32 pld[4] = {0, 0, 0, 0}; |
| |
| if ((mci_hw->bt_state != MCI_BT_AWAKE) || |
| (mci_hw->config & ATH_MCI_CONFIG_DISABLE_MCI_CAL)) |
| return; |
| |
| MCI_GPM_SET_CAL_TYPE(pld, MCI_GPM_WLAN_CAL_REQ); |
| pld[MCI_GPM_WLAN_CAL_W_SEQUENCE] = mci_hw->wlan_cal_seq++; |
| |
| ar9003_mci_send_message(ah, MCI_GPM, 0, pld, 16, true, false); |
| |
| if (ar9003_mci_wait_for_gpm(ah, MCI_GPM_BT_CAL_GRANT, 0, 50000)) { |
| ath_dbg(common, MCI, "MCI BT_CAL_GRANT received\n"); |
| } else { |
| *is_reusable = false; |
| ath_dbg(common, MCI, "MCI BT_CAL_GRANT not received\n"); |
| } |
| } |
| |
| void ar9003_mci_init_cal_done(struct ath_hw *ah) |
| { |
| struct ath9k_hw_mci *mci_hw = &ah->btcoex_hw.mci; |
| u32 pld[4] = {0, 0, 0, 0}; |
| |
| if ((mci_hw->bt_state != MCI_BT_AWAKE) || |
| (mci_hw->config & ATH_MCI_CONFIG_DISABLE_MCI_CAL)) |
| return; |
| |
| MCI_GPM_SET_CAL_TYPE(pld, MCI_GPM_WLAN_CAL_DONE); |
| pld[MCI_GPM_WLAN_CAL_W_SEQUENCE] = mci_hw->wlan_cal_done++; |
| ar9003_mci_send_message(ah, MCI_GPM, 0, pld, 16, true, false); |
| } |
| |
| int ar9003_mci_setup(struct ath_hw *ah, u32 gpm_addr, void *gpm_buf, |
| u16 len, u32 sched_addr) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| mci->gpm_addr = gpm_addr; |
| mci->gpm_buf = gpm_buf; |
| mci->gpm_len = len; |
| mci->sched_addr = sched_addr; |
| |
| return ar9003_mci_reset(ah, true, true, true); |
| } |
| EXPORT_SYMBOL(ar9003_mci_setup); |
| |
| void ar9003_mci_cleanup(struct ath_hw *ah) |
| { |
| /* Turn off MCI and Jupiter mode. */ |
| REG_WRITE(ah, AR_BTCOEX_CTRL, 0x00); |
| ar9003_mci_disable_interrupt(ah); |
| } |
| EXPORT_SYMBOL(ar9003_mci_cleanup); |
| |
| u32 ar9003_mci_state(struct ath_hw *ah, u32 state_type) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 value = 0, tsf; |
| u8 query_type; |
| |
| switch (state_type) { |
| case MCI_STATE_ENABLE: |
| if (mci->ready) { |
| value = REG_READ(ah, AR_BTCOEX_CTRL); |
| |
| if ((value == 0xdeadbeef) || (value == 0xffffffff)) |
| value = 0; |
| } |
| value &= AR_BTCOEX_CTRL_MCI_MODE_EN; |
| break; |
| case MCI_STATE_INIT_GPM_OFFSET: |
| value = MS(REG_READ(ah, AR_MCI_GPM_1), AR_MCI_GPM_WRITE_PTR); |
| |
| if (value < mci->gpm_len) |
| mci->gpm_idx = value; |
| else |
| mci->gpm_idx = 0; |
| break; |
| case MCI_STATE_LAST_SCHD_MSG_OFFSET: |
| value = MS(REG_READ(ah, AR_MCI_RX_STATUS), |
| AR_MCI_RX_LAST_SCHD_MSG_INDEX); |
| /* Make it in bytes */ |
| value <<= 4; |
| break; |
| case MCI_STATE_REMOTE_SLEEP: |
| value = MS(REG_READ(ah, AR_MCI_RX_STATUS), |
| AR_MCI_RX_REMOTE_SLEEP) ? |
| MCI_BT_SLEEP : MCI_BT_AWAKE; |
| break; |
| case MCI_STATE_SET_BT_AWAKE: |
| mci->bt_state = MCI_BT_AWAKE; |
| ar9003_mci_send_coex_version_query(ah, true); |
| ar9003_mci_send_coex_wlan_channels(ah, true); |
| |
| if (mci->unhalt_bt_gpm) |
| ar9003_mci_send_coex_halt_bt_gpm(ah, false, true); |
| |
| ar9003_mci_2g5g_switch(ah, false); |
| break; |
| case MCI_STATE_RESET_REQ_WAKE: |
| ar9003_mci_reset_req_wakeup(ah); |
| mci->update_2g5g = true; |
| |
| if (mci->config & ATH_MCI_CONFIG_MCI_OBS_MASK) { |
| /* Check if we still have control of the GPIOs */ |
| if ((REG_READ(ah, AR_GLB_GPIO_CONTROL) & |
| ATH_MCI_CONFIG_MCI_OBS_GPIO) != |
| ATH_MCI_CONFIG_MCI_OBS_GPIO) { |
| ar9003_mci_observation_set_up(ah); |
| } |
| } |
| break; |
| case MCI_STATE_SEND_WLAN_COEX_VERSION: |
| ar9003_mci_send_coex_version_response(ah, true); |
| break; |
| case MCI_STATE_SEND_VERSION_QUERY: |
| ar9003_mci_send_coex_version_query(ah, true); |
| break; |
| case MCI_STATE_SEND_STATUS_QUERY: |
| query_type = MCI_GPM_COEX_QUERY_BT_TOPOLOGY; |
| ar9003_mci_send_coex_bt_status_query(ah, true, query_type); |
| break; |
| case MCI_STATE_RECOVER_RX: |
| tsf = ath9k_hw_gettsf32(ah); |
| if ((tsf - mci->last_recovery) <= MCI_RECOVERY_DUR_TSF) { |
| ath_dbg(ath9k_hw_common(ah), MCI, |
| "(MCI) ignore Rx recovery\n"); |
| break; |
| } |
| ath_dbg(ath9k_hw_common(ah), MCI, "(MCI) RECOVER RX\n"); |
| mci->last_recovery = tsf; |
| ar9003_mci_prep_interface(ah); |
| mci->query_bt = true; |
| mci->need_flush_btinfo = true; |
| ar9003_mci_send_coex_wlan_channels(ah, true); |
| ar9003_mci_2g5g_switch(ah, false); |
| break; |
| case MCI_STATE_NEED_FTP_STOMP: |
| value = !(mci->config & ATH_MCI_CONFIG_DISABLE_FTP_STOMP); |
| break; |
| case MCI_STATE_NEED_FLUSH_BT_INFO: |
| value = (!mci->unhalt_bt_gpm && mci->need_flush_btinfo) ? 1 : 0; |
| mci->need_flush_btinfo = false; |
| break; |
| case MCI_STATE_AIC_CAL: |
| if (ath9k_hw_is_aic_enabled(ah)) |
| value = ar9003_aic_calibration(ah); |
| break; |
| case MCI_STATE_AIC_START: |
| if (ath9k_hw_is_aic_enabled(ah)) |
| ar9003_aic_start_normal(ah); |
| break; |
| case MCI_STATE_AIC_CAL_RESET: |
| if (ath9k_hw_is_aic_enabled(ah)) |
| value = ar9003_aic_cal_reset(ah); |
| break; |
| case MCI_STATE_AIC_CAL_SINGLE: |
| if (ath9k_hw_is_aic_enabled(ah)) |
| value = ar9003_aic_calibration_single(ah); |
| break; |
| default: |
| break; |
| } |
| |
| return value; |
| } |
| EXPORT_SYMBOL(ar9003_mci_state); |
| |
| void ar9003_mci_bt_gain_ctrl(struct ath_hw *ah) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| ath_dbg(common, MCI, "Give LNA and SPDT control to BT\n"); |
| |
| ar9003_mci_send_lna_take(ah, true); |
| udelay(50); |
| |
| REG_SET_BIT(ah, AR_PHY_GLB_CONTROL, AR_BTCOEX_CTRL_BT_OWN_SPDT_CTRL); |
| mci->is_2g = false; |
| mci->update_2g5g = true; |
| ar9003_mci_send_2g5g_status(ah, true); |
| |
| /* Force another 2g5g update at next scanning */ |
| mci->update_2g5g = true; |
| } |
| |
| void ar9003_mci_set_power_awake(struct ath_hw *ah) |
| { |
| u32 btcoex_ctrl2, diag_sw; |
| int i; |
| u8 lna_ctrl, bt_sleep; |
| |
| for (i = 0; i < AH_WAIT_TIMEOUT; i++) { |
| btcoex_ctrl2 = REG_READ(ah, AR_BTCOEX_CTRL2); |
| if (btcoex_ctrl2 != 0xdeadbeef) |
| break; |
| udelay(AH_TIME_QUANTUM); |
| } |
| REG_WRITE(ah, AR_BTCOEX_CTRL2, (btcoex_ctrl2 | BIT(23))); |
| |
| for (i = 0; i < AH_WAIT_TIMEOUT; i++) { |
| diag_sw = REG_READ(ah, AR_DIAG_SW); |
| if (diag_sw != 0xdeadbeef) |
| break; |
| udelay(AH_TIME_QUANTUM); |
| } |
| REG_WRITE(ah, AR_DIAG_SW, (diag_sw | BIT(27) | BIT(19) | BIT(18))); |
| lna_ctrl = REG_READ(ah, AR_OBS_BUS_CTRL) & 0x3; |
| bt_sleep = MS(REG_READ(ah, AR_MCI_RX_STATUS), AR_MCI_RX_REMOTE_SLEEP); |
| |
| REG_WRITE(ah, AR_BTCOEX_CTRL2, btcoex_ctrl2); |
| REG_WRITE(ah, AR_DIAG_SW, diag_sw); |
| |
| if (bt_sleep && (lna_ctrl == 2)) { |
| REG_SET_BIT(ah, AR_BTCOEX_RC, 0x1); |
| REG_CLR_BIT(ah, AR_BTCOEX_RC, 0x1); |
| udelay(50); |
| } |
| } |
| |
| void ar9003_mci_check_gpm_offset(struct ath_hw *ah) |
| { |
| struct ath_common *common = ath9k_hw_common(ah); |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 offset; |
| |
| /* |
| * This should only be called before "MAC Warm Reset" or "MCI Reset Rx". |
| */ |
| offset = MS(REG_READ(ah, AR_MCI_GPM_1), AR_MCI_GPM_WRITE_PTR); |
| if (mci->gpm_idx == offset) |
| return; |
| ath_dbg(common, MCI, "GPM cached write pointer mismatch %d %d\n", |
| mci->gpm_idx, offset); |
| mci->query_bt = true; |
| mci->need_flush_btinfo = true; |
| mci->gpm_idx = 0; |
| } |
| |
| u32 ar9003_mci_get_next_gpm_offset(struct ath_hw *ah, u32 *more) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| u32 offset, more_gpm = 0, gpm_ptr; |
| |
| /* |
| * This could be useful to avoid new GPM message interrupt which |
| * may lead to spurious interrupt after power sleep, or multiple |
| * entry of ath_mci_intr(). |
| * Adding empty GPM check by returning HAL_MCI_GPM_INVALID can |
| * alleviate this effect, but clearing GPM RX interrupt bit is |
| * safe, because whether this is called from hw or driver code |
| * there must be an interrupt bit set/triggered initially |
| */ |
| REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW, |
| AR_MCI_INTERRUPT_RX_MSG_GPM); |
| |
| gpm_ptr = MS(REG_READ(ah, AR_MCI_GPM_1), AR_MCI_GPM_WRITE_PTR); |
| offset = gpm_ptr; |
| |
| if (!offset) |
| offset = mci->gpm_len - 1; |
| else if (offset >= mci->gpm_len) { |
| if (offset != 0xFFFF) |
| offset = 0; |
| } else { |
| offset--; |
| } |
| |
| if ((offset == 0xFFFF) || (gpm_ptr == mci->gpm_idx)) { |
| offset = MCI_GPM_INVALID; |
| more_gpm = MCI_GPM_NOMORE; |
| goto out; |
| } |
| for (;;) { |
| u32 temp_index; |
| |
| /* skip reserved GPM if any */ |
| |
| if (offset != mci->gpm_idx) |
| more_gpm = MCI_GPM_MORE; |
| else |
| more_gpm = MCI_GPM_NOMORE; |
| |
| temp_index = mci->gpm_idx; |
| |
| if (temp_index >= mci->gpm_len) |
| temp_index = 0; |
| |
| mci->gpm_idx++; |
| |
| if (mci->gpm_idx >= mci->gpm_len) |
| mci->gpm_idx = 0; |
| |
| if (ar9003_mci_is_gpm_valid(ah, temp_index)) { |
| offset = temp_index; |
| break; |
| } |
| |
| if (more_gpm == MCI_GPM_NOMORE) { |
| offset = MCI_GPM_INVALID; |
| break; |
| } |
| } |
| |
| if (offset != MCI_GPM_INVALID) |
| offset <<= 4; |
| out: |
| if (more) |
| *more = more_gpm; |
| |
| return offset; |
| } |
| EXPORT_SYMBOL(ar9003_mci_get_next_gpm_offset); |
| |
| void ar9003_mci_set_bt_version(struct ath_hw *ah, u8 major, u8 minor) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| mci->bt_ver_major = major; |
| mci->bt_ver_minor = minor; |
| mci->bt_version_known = true; |
| ath_dbg(ath9k_hw_common(ah), MCI, "MCI BT version set: %d.%d\n", |
| mci->bt_ver_major, mci->bt_ver_minor); |
| } |
| EXPORT_SYMBOL(ar9003_mci_set_bt_version); |
| |
| void ar9003_mci_send_wlan_channels(struct ath_hw *ah) |
| { |
| struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci; |
| |
| mci->wlan_channels_update = true; |
| ar9003_mci_send_coex_wlan_channels(ah, true); |
| } |
| EXPORT_SYMBOL(ar9003_mci_send_wlan_channels); |
| |
| u16 ar9003_mci_get_max_txpower(struct ath_hw *ah, u8 ctlmode) |
| { |
| if (!ah->btcoex_hw.mci.concur_tx) |
| goto out; |
| |
| if (ctlmode == CTL_2GHT20) |
| return ATH_BTCOEX_HT20_MAX_TXPOWER; |
| else if (ctlmode == CTL_2GHT40) |
| return ATH_BTCOEX_HT40_MAX_TXPOWER; |
| |
| out: |
| return -1; |
| } |