| // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT) |
| /* |
| * Copyright (c) 2022-2023 TQ-Systems GmbH <linux@ew.tq-group.com>, |
| * D-82229 Seefeld, Germany. |
| * Author: Markus Niebel |
| * Author: Alexander Stein |
| */ |
| /dts-v1/; |
| |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/net/ti-dp83867.h> |
| #include <dt-bindings/pwm/pwm.h> |
| |
| #include "imx93-tqma9352.dtsi" |
| |
| /{ |
| model = "TQ-Systems i.MX93 TQMa93xxLA/TQMa93xxCA on MBa93xxCA starter kit"; |
| compatible = "tq,imx93-tqma9352-mba93xxca", |
| "tq,imx93-tqma9352", "fsl,imx93"; |
| chassis-type = "embedded"; |
| |
| chosen { |
| stdout-path = &lpuart1; |
| }; |
| |
| aliases { |
| eeprom0 = &eeprom0; |
| rtc0 = &pcf85063; |
| rtc1 = &bbnsm_rtc; |
| }; |
| |
| backlight_lvds: backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&tpm5 0 5000000 0>; |
| brightness-levels = <0 4 8 16 32 64 128 255>; |
| default-brightness-level = <7>; |
| power-supply = <®_12v0>; |
| enable-gpios = <&expander2 2 GPIO_ACTIVE_HIGH>; |
| status = "disabled"; |
| }; |
| |
| fan0: pwm-fan { |
| compatible = "pwm-fan"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwmfan>; |
| fan-supply = <®_pwm_fan>; |
| #cooling-cells = <2>; |
| /* typical 25 kHz -> 40.000 nsec */ |
| pwms = <&tpm6 0 40000 PWM_POLARITY_INVERTED>; |
| cooling-levels = <0 32 64 128 196 240>; |
| pulses-per-revolution = <2>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <9 IRQ_TYPE_EDGE_FALLING>; |
| status = "disabled"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| autorepeat; |
| |
| switch-a { |
| label = "switcha"; |
| linux,code = <BTN_0>; |
| gpios = <&expander0 6 GPIO_ACTIVE_LOW>; |
| wakeup-source; |
| }; |
| |
| switch-b { |
| label = "switchb"; |
| linux,code = <BTN_1>; |
| gpios = <&expander0 7 GPIO_ACTIVE_LOW>; |
| wakeup-source; |
| }; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| |
| led-1 { |
| color = <LED_COLOR_ID_GREEN>; |
| function = LED_FUNCTION_STATUS; |
| gpios = <&expander2 6 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "default-on"; |
| }; |
| |
| led-2 { |
| color = <LED_COLOR_ID_AMBER>; |
| function = LED_FUNCTION_HEARTBEAT; |
| gpios = <&expander2 7 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| |
| iio-hwmon { |
| compatible = "iio-hwmon"; |
| io-channels = <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>; |
| }; |
| |
| reg_3v3: regulator-3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "V_3V3_MB"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| reg_5v0: regulator-5v0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "V_5V0_MB"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| reg_12v0: regulator-12v0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "V_12V"; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| gpio = <&expander1 7 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_mpcie_1v5: regulator-mpcie-1v5 { |
| compatible = "regulator-fixed"; |
| regulator-name = "V_1V5_MPCIE"; |
| regulator-min-microvolt = <1500000>; |
| regulator-max-microvolt = <1500000>; |
| gpio = <&expander0 2 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_mpcie_3v3: regulator-mpcie-3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "V_3V3_MPCIE"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&expander0 3 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_pwm_fan: regulator-pwm-fan { |
| compatible = "regulator-fixed"; |
| regulator-name = "FAN_PWR"; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| gpio = <&expander0 0 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| vin-supply = <®_12v0>; |
| }; |
| |
| thermal-zones { |
| cpu-thermal { |
| trips { |
| cpu_active0: trip-active0 { |
| temperature = <40000>; |
| hysteresis = <5000>; |
| type = "active"; |
| }; |
| |
| cpu_active1: trip-active1 { |
| temperature = <48000>; |
| hysteresis = <3000>; |
| type = "active"; |
| }; |
| |
| cpu_active2: trip-active2 { |
| temperature = <60000>; |
| hysteresis = <10000>; |
| type = "active"; |
| }; |
| }; |
| |
| cooling-maps { |
| map1 { |
| trip = <&cpu_active0>; |
| cooling-device = <&fan0 1 1>; |
| }; |
| |
| map2 { |
| trip = <&cpu_active1>; |
| cooling-device = <&fan0 2 2>; |
| }; |
| |
| map3 { |
| trip = <&cpu_active2>; |
| cooling-device = <&fan0 3 3>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &adc1 { |
| status = "okay"; |
| }; |
| |
| &eqos { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_eqos>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy_eqos>; |
| status = "okay"; |
| |
| mdio { |
| compatible = "snps,dwmac-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy_eqos: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_eqos_phy>; |
| reset-gpios = <&expander1 0 GPIO_ACTIVE_LOW>; |
| reset-assert-us = <500000>; |
| reset-deassert-us = <50000>; |
| interrupt-parent = <&gpio3>; |
| interrupts = <26 IRQ_TYPE_EDGE_FALLING>; |
| enet-phy-lane-no-swap; |
| ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; |
| ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; |
| ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; |
| ti,dp83867-rxctrl-strap-quirk; |
| ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; |
| }; |
| }; |
| }; |
| |
| &fec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy_fec>; |
| fsl,magic-packet; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <5000000>; |
| |
| ethphy_fec: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec_phy>; |
| reset-gpios = <&expander1 1 GPIO_ACTIVE_LOW>; |
| reset-assert-us = <500000>; |
| reset-deassert-us = <50000>; |
| interrupt-parent = <&gpio3>; |
| interrupts = <27 IRQ_TYPE_EDGE_FALLING>; |
| enet-phy-lane-no-swap; |
| ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; |
| ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; |
| ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; |
| ti,dp83867-rxctrl-strap-quirk; |
| ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; |
| }; |
| }; |
| }; |
| |
| &flexcan1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan1>; |
| xceiver-supply = <®_3v3>; |
| status = "okay"; |
| }; |
| |
| &flexcan2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan2>; |
| xceiver-supply = <®_3v3>; |
| status = "okay"; |
| }; |
| |
| &gpio1 { |
| expander-irq-hog { |
| gpio-hog; |
| gpios = <12 GPIO_ACTIVE_LOW>; |
| input; |
| line-name = "PEX_INT#"; |
| }; |
| |
| tcpc-irq-hog { |
| gpio-hog; |
| gpios = <2 GPIO_ACTIVE_LOW>; |
| input; |
| line-name = "USB_C_ALERT#"; |
| }; |
| }; |
| |
| &lpi2c3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&pinctrl_lpi2c3>; |
| pinctrl-1 = <&pinctrl_lpi2c3>; |
| status = "okay"; |
| |
| temperature-sensor@1c { |
| compatible = "nxp,se97b", "jedec,jc-42.4-temp"; |
| reg = <0x1c>; |
| }; |
| |
| ptn5110: usb-typec@50 { |
| compatible = "nxp,ptn5110", "tcpci"; |
| reg = <0x50>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_typec>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <2 IRQ_TYPE_EDGE_FALLING>; |
| |
| connector { |
| compatible = "usb-c-connector"; |
| label = "X17"; |
| power-role = "dual"; |
| data-role = "dual"; |
| try-power-role = "sink"; |
| typec-power-opmode = "default"; |
| pd-disable; |
| self-powered; |
| |
| port { |
| typec_con_hs: endpoint { |
| remote-endpoint = <&typec_hs>; |
| }; |
| }; |
| }; |
| }; |
| |
| eeprom2: eeprom@54 { |
| compatible = "nxp,se97b", "atmel,24c02"; |
| reg = <0x54>; |
| pagesize = <16>; |
| vcc-supply = <®_3v3>; |
| }; |
| |
| expander0: gpio@70 { |
| compatible = "nxp,pca9538"; |
| reg = <0x70>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pexp_irq>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <12 IRQ_TYPE_LEVEL_LOW>; |
| vcc-supply = <®_3v3>; |
| gpio-line-names = "FAN_PWR_EN", "MPCIE_WAKE#", |
| "MPCIE_1V5_EN", "MPCIE_3V3_EN", |
| "MPCIE_PERST#", "MPCIE_WDISABLE#", |
| "BUTTON_A#", "BUTTON_B#"; |
| |
| mpcie-wake-hog { |
| gpio-hog; |
| gpios = <1 GPIO_ACTIVE_LOW>; |
| input; |
| line-name = "MPCIE_WAKE#"; |
| }; |
| |
| /* |
| * Controls the mPCIE slot reset which is low active as |
| * reset signal. The output-low states, the signal is |
| * inactive, e.g. not in reset |
| */ |
| mpcie_rst_hog: mpcie-rst-hog { |
| gpio-hog; |
| gpios = <4 GPIO_ACTIVE_LOW>; |
| output-low; |
| line-name = "MPCIE_PERST#"; |
| }; |
| |
| /* |
| * Controls the mPCIE slot WDISABLE pin which is low active |
| * as disable signal. The output-low states, the signal is |
| * inactive, e.g. not disabled |
| */ |
| mpcie_wdisable_hog: mpcie-wdisable-hog { |
| gpio-hog; |
| gpios = <5 GPIO_ACTIVE_LOW>; |
| output-low; |
| line-name = "MPCIE_WDISABLE#"; |
| }; |
| }; |
| |
| expander1: gpio@71 { |
| compatible = "nxp,pca9538"; |
| reg = <0x71>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| vcc-supply = <®_3v3>; |
| gpio-line-names = "ENET1_RESET#", "ENET2_RESET#", |
| "USB_RESET#", "", |
| "WLAN_PD#", "WLAN_W_DISABLE#", |
| "WLAN_PERST#", "12V_EN"; |
| |
| /* |
| * Controls the WiFi card PD pin which is low active |
| * as power down signal. The output-high states, the signal |
| * is active, e.g. card is powered down |
| */ |
| wlan-pd-hog { |
| gpio-hog; |
| gpios = <4 GPIO_ACTIVE_LOW>; |
| output-high; |
| line-name = "WLAN_PD#"; |
| }; |
| |
| /* |
| * Controls the WiFi card disable pin which is low active |
| * as disable signal. The output-high states, the signal |
| * is active, e.g. card is disabled |
| */ |
| wlan-wdisable-hog { |
| gpio-hog; |
| gpios = <5 GPIO_ACTIVE_LOW>; |
| output-high; |
| line-name = "WLAN_W_DISABLE#"; |
| }; |
| |
| /* |
| * Controls the WiFi card reset pin which is low active |
| * as reset signal. The output-high states, the signal |
| * is active, e.g. card in reset |
| */ |
| wlan-perst-hog { |
| gpio-hog; |
| gpios = <6 GPIO_ACTIVE_LOW>; |
| output-high; |
| line-name = "WLAN_PERST#"; |
| }; |
| }; |
| |
| expander2: gpio@72 { |
| compatible = "nxp,pca9538"; |
| reg = <0x72>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| vcc-supply = <®_3v3>; |
| gpio-line-names = "LCD_RESET#", "LCD_PWR_EN", |
| "LCD_BLT_EN", "DP_EN", |
| "MIPI_CSI_EN", "MIPI_CSI_RST#", |
| "USER_LED1", "USER_LED2"; |
| }; |
| }; |
| |
| &lpi2c5 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&pinctrl_lpi2c5>; |
| pinctrl-1 = <&pinctrl_lpi2c5>; |
| status = "okay"; |
| }; |
| |
| &lpspi6 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&pinctrl_lpspi6>; |
| pinctrl-1 = <&pinctrl_lpspi6>; |
| status = "okay"; |
| }; |
| |
| &lpuart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| }; |
| |
| &lpuart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| linux,rs485-enabled-at-boot-time; |
| status = "okay"; |
| }; |
| |
| /* disabled per default, console for M33 */ |
| &lpuart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| status = "disabled"; |
| }; |
| |
| &lpuart6 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart6>; |
| status = "okay"; |
| }; |
| |
| &lpuart8 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart8>; |
| status = "okay"; |
| }; |
| |
| &tpm5 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_tpm5>; |
| }; |
| |
| &tpm6 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_tpm6>; |
| status = "okay"; |
| }; |
| |
| &usbotg1 { |
| dr_mode = "otg"; |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| usb-role-switch; |
| disable-over-current; |
| samsung,picophy-pre-emp-curr-control = <3>; |
| samsung,picophy-dc-vol-level-adjust = <7>; |
| status = "okay"; |
| |
| port { |
| typec_hs: endpoint { |
| remote-endpoint = <&typec_con_hs>; |
| }; |
| }; |
| }; |
| |
| &usbotg2 { |
| dr_mode = "host"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| disable-over-current; |
| samsung,picophy-pre-emp-curr-control = <3>; |
| samsung,picophy-dc-vol-level-adjust = <7>; |
| status = "okay"; |
| |
| hub_2_0: hub@1 { |
| compatible = "usb424,2517"; |
| reg = <1>; |
| reset-gpios = <&expander1 2 GPIO_ACTIVE_LOW>; |
| vdd-supply = <®_3v3>; |
| }; |
| }; |
| |
| &usdhc2 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc2_hs>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-1 = <&pinctrl_usdhc2_uhs>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-2 = <&pinctrl_usdhc2_uhs>, <&pinctrl_usdhc2_gpio>; |
| cd-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| bus-width = <4>; |
| no-sdio; |
| no-mmc; |
| disable-wp; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_eqos: eqosgrp { |
| fsl,pins = < |
| /* PD | FSEL_2 | DSE X4 */ |
| MX93_PAD_ENET1_MDC__ENET_QOS_MDC 0x51e |
| MX93_PAD_ENET1_MDIO__ENET_QOS_MDIO 0x4000051e |
| /* PD | FSEL_2 | DSE X6 */ |
| MX93_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0 0x57e |
| MX93_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1 0x57e |
| MX93_PAD_ENET1_RD2__ENET_QOS_RGMII_RD2 0x57e |
| MX93_PAD_ENET1_RD3__ENET_QOS_RGMII_RD3 0x57e |
| /* PD | FSEL_3 | DSE X6 */ |
| MX93_PAD_ENET1_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x5fe |
| MX93_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x57e |
| /* PD | FSEL_2 | DSE X4 */ |
| MX93_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0 0x51e |
| MX93_PAD_ENET1_TD1__ENET_QOS_RGMII_TD1 0x51e |
| MX93_PAD_ENET1_TD2__ENET_QOS_RGMII_TD2 0x51e |
| MX93_PAD_ENET1_TD3__ENET_QOS_RGMII_TD3 0x51e |
| MX93_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x51e |
| /* PD | FSEL_3 | DSE X3 */ |
| MX93_PAD_ENET1_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x58e |
| >; |
| }; |
| |
| pinctrl_eqos_phy: eqosphygrp { |
| fsl,pins = < |
| MX93_PAD_CCM_CLKO1__GPIO3_IO26 0x1306 |
| >; |
| }; |
| |
| pinctrl_fec: fecgrp { |
| fsl,pins = < |
| /* PD | FSEL_2 | DSE X4 */ |
| MX93_PAD_ENET2_MDC__ENET1_MDC 0x51e |
| MX93_PAD_ENET2_MDIO__ENET1_MDIO 0x4000051e |
| /* PD | FSEL_2 | DSE X6 */ |
| MX93_PAD_ENET2_RD0__ENET1_RGMII_RD0 0x57e |
| MX93_PAD_ENET2_RD1__ENET1_RGMII_RD1 0x57e |
| MX93_PAD_ENET2_RD2__ENET1_RGMII_RD2 0x57e |
| MX93_PAD_ENET2_RD3__ENET1_RGMII_RD3 0x57e |
| /* PD | FSEL_3 | DSE X6 */ |
| MX93_PAD_ENET2_RXC__ENET1_RGMII_RXC 0x5fe |
| MX93_PAD_ENET2_RX_CTL__ENET1_RGMII_RX_CTL 0x57e |
| /* PD | FSEL_2 | DSE X4 */ |
| MX93_PAD_ENET2_TD0__ENET1_RGMII_TD0 0x51e |
| MX93_PAD_ENET2_TD1__ENET1_RGMII_TD1 0x51e |
| MX93_PAD_ENET2_TD2__ENET1_RGMII_TD2 0x51e |
| MX93_PAD_ENET2_TD3__ENET1_RGMII_TD3 0x51e |
| MX93_PAD_ENET2_TX_CTL__ENET1_RGMII_TX_CTL 0x51e |
| /* PD | FSEL_3 | DSE X3 */ |
| MX93_PAD_ENET2_TXC__ENET1_RGMII_TXC 0x58e |
| >; |
| }; |
| |
| pinctrl_fec_phy: fecphygrp { |
| fsl,pins = < |
| MX93_PAD_CCM_CLKO2__GPIO3_IO27 0x1306 |
| >; |
| }; |
| |
| pinctrl_flexcan1: flexcan1grp { |
| fsl,pins = < |
| MX93_PAD_PDM_BIT_STREAM0__CAN1_RX 0x139e |
| MX93_PAD_PDM_CLK__CAN1_TX 0x139e |
| >; |
| }; |
| |
| pinctrl_flexcan2: flexcan2grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO25__CAN2_TX 0x139e |
| MX93_PAD_GPIO_IO27__CAN2_RX 0x139e |
| >; |
| }; |
| |
| pinctrl_lpi2c3: lpi2c3grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO28__LPI2C3_SDA 0x40000b9e |
| MX93_PAD_GPIO_IO29__LPI2C3_SCL 0x40000b9e |
| >; |
| }; |
| |
| pinctrl_lpi2c5: lpi2c5grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO22__LPI2C5_SDA 0x40000b9e |
| MX93_PAD_GPIO_IO23__LPI2C5_SCL 0x40000b9e |
| >; |
| }; |
| |
| pinctrl_lpspi6: lpspi6grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO00__LPSPI6_PCS0 0x3fe |
| MX93_PAD_GPIO_IO01__LPSPI6_SIN 0x3fe |
| MX93_PAD_GPIO_IO02__LPSPI6_SOUT 0x3fe |
| MX93_PAD_GPIO_IO03__LPSPI6_SCK 0x3fe |
| >; |
| }; |
| |
| pinctrl_pexp_irq: pexpirqgrp { |
| fsl,pins = < |
| MX93_PAD_SAI1_TXC__GPIO1_IO12 0x1306 |
| >; |
| }; |
| |
| pinctrl_pwmfan: pwmfangrp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO09__GPIO2_IO09 0x1306 |
| >; |
| }; |
| |
| pinctrl_tpm5: tpm5grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO06__TPM5_CH0 0x57e |
| >; |
| }; |
| |
| pinctrl_tpm6: tpm6grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO08__TPM6_CH0 0x57e |
| >; |
| }; |
| |
| pinctrl_typec: typecgrp { |
| fsl,pins = < |
| MX93_PAD_I2C2_SCL__GPIO1_IO02 0x1306 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX93_PAD_UART1_RXD__LPUART1_RX 0x31e |
| MX93_PAD_UART1_TXD__LPUART1_TX 0x31e |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX93_PAD_UART2_TXD__LPUART2_TX 0x31e |
| MX93_PAD_UART2_RXD__LPUART2_RX 0x31e |
| MX93_PAD_SAI1_TXD0__LPUART2_RTS_B 0x51e |
| >; |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO14__LPUART3_TX 0x31e |
| MX93_PAD_GPIO_IO15__LPUART3_RX 0x31e |
| >; |
| }; |
| |
| pinctrl_uart6: uart6grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO04__LPUART6_TX 0x31e |
| MX93_PAD_GPIO_IO05__LPUART6_RX 0x31e |
| >; |
| }; |
| |
| pinctrl_uart8: uart8grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO12__LPUART8_TX 0x31e |
| MX93_PAD_GPIO_IO13__LPUART8_RX 0x31e |
| >; |
| }; |
| |
| pinctrl_usdhc2_gpio: usdhc2gpiogrp { |
| fsl,pins = < |
| MX93_PAD_SD2_CD_B__GPIO3_IO00 0x31e |
| >; |
| }; |
| |
| pinctrl_usdhc2_hs: usdhc2hsgrp { |
| fsl,pins = < |
| /* HYS | PD | PU | FSEL_3 | DSE X5 */ |
| MX93_PAD_SD2_CLK__USDHC2_CLK 0x17be |
| /* HYS | PD | PU | FSEL_3 | DSE X4 */ |
| MX93_PAD_SD2_CMD__USDHC2_CMD 0x139e |
| /* HYS | PD | PU | FSEL_3 | DSE X3 */ |
| MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x138e |
| MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x138e |
| MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x138e |
| MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x138e |
| /* PD | PU | FSEL_2 | DSE X3 */ |
| MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x50e |
| >; |
| }; |
| |
| pinctrl_usdhc2_uhs: usdhc2uhsgrp { |
| fsl,pins = < |
| /* HYS | PD | PU | FSEL_3 | DSE X6 */ |
| MX93_PAD_SD2_CLK__USDHC2_CLK 0x17fe |
| /* HYS | PD | PU | FSEL_3 | DSE X4 */ |
| MX93_PAD_SD2_CMD__USDHC2_CMD 0x139e |
| MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x139e |
| MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x139e |
| MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x139e |
| MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x139e |
| /* PD | PU | FSEL_2 | DSE X3 */ |
| MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x50e |
| >; |
| }; |
| }; |
