| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/ |
| * |
| * Product Link: https://www.ti.com/tool/J721EXCPXEVM |
| */ |
| |
| /dts-v1/; |
| |
| #include "k3-j721e-som-p0.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/net/ti-dp83867.h> |
| #include <dt-bindings/phy/phy-cadence.h> |
| |
| / { |
| compatible = "ti,j721e-evm", "ti,j721e"; |
| model = "Texas Instruments J721e EVM"; |
| |
| aliases { |
| serial0 = &wkup_uart0; |
| serial1 = &mcu_uart0; |
| serial2 = &main_uart0; |
| serial3 = &main_uart1; |
| serial4 = &main_uart2; |
| serial6 = &main_uart4; |
| ethernet0 = &cpsw_port1; |
| mmc0 = &main_sdhci0; |
| mmc1 = &main_sdhci1; |
| }; |
| |
| chosen { |
| stdout-path = "serial2:115200n8"; |
| }; |
| |
| gpio_keys: gpio-keys { |
| compatible = "gpio-keys"; |
| autorepeat; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sw10_button_pins_default>, <&sw11_button_pins_default>; |
| |
| sw10: switch-10 { |
| label = "GPIO Key USER1"; |
| linux,code = <BTN_0>; |
| gpios = <&main_gpio0 0 GPIO_ACTIVE_LOW>; |
| }; |
| |
| sw11: switch-11 { |
| label = "GPIO Key USER2"; |
| linux,code = <BTN_1>; |
| gpios = <&wkup_gpio0 7 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| evm_12v0: fixedregulator-evm12v0 { |
| /* main supply */ |
| compatible = "regulator-fixed"; |
| regulator-name = "evm_12v0"; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vsys_3v3: fixedregulator-vsys3v3 { |
| /* Output of LMS140 */ |
| compatible = "regulator-fixed"; |
| regulator-name = "vsys_3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&evm_12v0>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vsys_5v0: fixedregulator-vsys5v0 { |
| /* Output of LM5140 */ |
| compatible = "regulator-fixed"; |
| regulator-name = "vsys_5v0"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&evm_12v0>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vdd_mmc1: fixedregulator-sd { |
| compatible = "regulator-fixed"; |
| regulator-name = "vdd_mmc1"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| enable-active-high; |
| vin-supply = <&vsys_3v3>; |
| gpio = <&exp2 2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| vdd_sd_dv_alt: gpio-regulator-TLV71033 { |
| compatible = "regulator-gpio"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vdd_sd_dv_alt_pins_default>; |
| regulator-name = "tlv71033"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| vin-supply = <&vsys_5v0>; |
| gpios = <&main_gpio0 117 GPIO_ACTIVE_HIGH>; |
| states = <1800000 0x0>, |
| <3300000 0x1>; |
| }; |
| |
| sound0: sound-0 { |
| compatible = "ti,j721e-cpb-audio"; |
| model = "j721e-cpb"; |
| |
| ti,cpb-mcasp = <&mcasp10>; |
| ti,cpb-codec = <&pcm3168a_1>; |
| |
| clocks = <&k3_clks 184 1>, |
| <&k3_clks 184 2>, <&k3_clks 184 4>, |
| <&k3_clks 157 371>, |
| <&k3_clks 157 400>, <&k3_clks 157 401>; |
| clock-names = "cpb-mcasp-auxclk", |
| "cpb-mcasp-auxclk-48000", "cpb-mcasp-auxclk-44100", |
| "cpb-codec-scki", |
| "cpb-codec-scki-48000", "cpb-codec-scki-44100"; |
| }; |
| |
| transceiver1: can-phy0 { |
| compatible = "ti,tcan1043"; |
| #phy-cells = <0>; |
| max-bitrate = <5000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcu_mcan0_gpio_pins_default>; |
| standby-gpios = <&wkup_gpio0 54 GPIO_ACTIVE_LOW>; |
| enable-gpios = <&wkup_gpio0 0 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| transceiver2: can-phy1 { |
| compatible = "ti,tcan1042"; |
| #phy-cells = <0>; |
| max-bitrate = <5000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcu_mcan1_gpio_pins_default>; |
| standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| transceiver3: can-phy2 { |
| compatible = "ti,tcan1043"; |
| #phy-cells = <0>; |
| max-bitrate = <5000000>; |
| standby-gpios = <&exp2 7 GPIO_ACTIVE_LOW>; |
| enable-gpios = <&exp2 6 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| transceiver4: can-phy3 { |
| compatible = "ti,tcan1042"; |
| #phy-cells = <0>; |
| max-bitrate = <5000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_mcan2_gpio_pins_default>; |
| standby-gpios = <&main_gpio0 127 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| dp_pwr_3v3: regulator-dp-pwr { |
| compatible = "regulator-fixed"; |
| regulator-name = "dp-pwr"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&exp4 0 GPIO_ACTIVE_HIGH>; /* P0 - DP0_PWR_SW_EN */ |
| enable-active-high; |
| }; |
| |
| dp0: connector { |
| compatible = "dp-connector"; |
| label = "DP0"; |
| type = "full-size"; |
| dp-pwr-supply = <&dp_pwr_3v3>; |
| |
| port { |
| dp_connector_in: endpoint { |
| remote-endpoint = <&dp0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &main_pmx0 { |
| main_uart0_pins_default: main-uart0-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x1d4, PIN_INPUT, 1) /* (Y3) SPI1_CS0.UART0_CTSn */ |
| J721E_IOPAD(0x1c0, PIN_OUTPUT, 1) /* (AA2) SPI0_CS0.UART0_RTSn */ |
| J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */ |
| J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */ |
| >; |
| }; |
| |
| main_uart1_pins_default: main-uart1-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x1f8, PIN_INPUT, 0) /* (AA4) UART1_RXD */ |
| J721E_IOPAD(0x1fc, PIN_OUTPUT, 0) /* (AB4) UART1_TXD */ |
| >; |
| }; |
| |
| main_uart2_pins_default: main-uart2-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x1dc, PIN_INPUT, 3) /* (Y1) SPI1_CLK.UART2_RXD */ |
| J721E_IOPAD(0x1e0, PIN_OUTPUT, 3) /* (Y5) SPI1_D0.UART2_TXD */ |
| >; |
| }; |
| |
| main_uart4_pins_default: main-uart4-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x190, PIN_INPUT, 1) /* (W23) RGMII6_TD3.UART4_RXD */ |
| J721E_IOPAD(0x194, PIN_OUTPUT, 1) /* (W28) RGMII6_TD2.UART4_TXD */ |
| >; |
| }; |
| |
| sw10_button_pins_default: sw10-button-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x0, PIN_INPUT, 7) /* (AC18) EXTINTn.GPIO0_0 */ |
| >; |
| }; |
| |
| main_mmc1_pins_default: main-mmc1-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */ |
| J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */ |
| J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */ |
| J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */ |
| J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */ |
| J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */ |
| J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */ |
| J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */ |
| J721E_IOPAD(0x25c, PIN_INPUT, 0) /* (R28) MMC1_SDWP */ |
| >; |
| }; |
| |
| vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x1d8, PIN_INPUT, 7) /* (W4) SPI1_CS1.GPIO0_117 */ |
| >; |
| }; |
| |
| main_usbss0_pins_default: main-usbss0-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */ |
| J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */ |
| >; |
| }; |
| |
| main_usbss1_pins_default: main-usbss1-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */ |
| >; |
| }; |
| |
| dp0_pins_default: dp0-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x1c4, PIN_INPUT, 5) /* SPI0_CS1.DP0_HPD */ |
| >; |
| }; |
| |
| main_i2c1_exp4_pins_default: main-i2c1-exp4-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x230, PIN_INPUT, 7) /* (U2) ECAP0_IN_APWM_OUT.GPIO1_11 */ |
| >; |
| }; |
| |
| main_i2c0_pins_default: main-i2c0-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */ |
| J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */ |
| >; |
| }; |
| |
| main_i2c1_pins_default: main-i2c1-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */ |
| J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */ |
| >; |
| }; |
| |
| main_i2c3_pins_default: main-i2c3-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */ |
| J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */ |
| >; |
| }; |
| |
| main_i2c6_pins_default: main-i2c6-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x1d0, PIN_INPUT_PULLUP, 2) /* (AA3) SPI0_D1.I2C6_SCL */ |
| J721E_IOPAD(0x1e4, PIN_INPUT_PULLUP, 2) /* (Y2) SPI1_D1.I2C6_SDA */ |
| >; |
| }; |
| |
| mcasp10_pins_default: mcasp10-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */ |
| J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */ |
| J721E_IOPAD(0x160, PIN_OUTPUT_PULLDOWN, 12) /* (V28) RGMII5_TD3.MCASP10_AXR0 */ |
| J721E_IOPAD(0x164, PIN_OUTPUT_PULLDOWN, 12) /* (V29) RGMII5_TD2.MCASP10_AXR1 */ |
| J721E_IOPAD(0x170, PIN_OUTPUT_PULLDOWN, 12) /* (U29) RGMII5_TXC.MCASP10_AXR2 */ |
| J721E_IOPAD(0x174, PIN_OUTPUT_PULLDOWN, 12) /* (U25) RGMII5_RXC.MCASP10_AXR3 */ |
| J721E_IOPAD(0x198, PIN_INPUT_PULLDOWN, 12) /* (V25) RGMII6_TD1.MCASP10_AXR4 */ |
| J721E_IOPAD(0x19c, PIN_INPUT_PULLDOWN, 12) /* (W27) RGMII6_TD0.MCASP10_AXR5 */ |
| J721E_IOPAD(0x1a0, PIN_INPUT_PULLDOWN, 12) /* (W29) RGMII6_TXC.MCASP10_AXR6 */ |
| >; |
| }; |
| |
| audi_ext_refclk2_pins_default: audi-ext-refclk2-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */ |
| >; |
| }; |
| |
| main_mcan0_pins_default: main-mcan0-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x208, PIN_INPUT, 0) /* (W5) MCAN0_RX */ |
| J721E_IOPAD(0x20c, PIN_OUTPUT, 0) /* (W6) MCAN0_TX */ |
| >; |
| }; |
| |
| main_mcan2_pins_default: main-mcan2-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x01f0, PIN_INPUT, 3) /* (AC2) MCAN2_RX.GPIO0_123 */ |
| J721E_IOPAD(0x01f4, PIN_OUTPUT, 3) /* (AB1) MCAN2_TX.GPIO0_124 */ |
| >; |
| }; |
| |
| main_mcan2_gpio_pins_default: main-mcan2-gpio-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x200, PIN_INPUT, 7) /* (AC4) UART1_CTSn.GPIO0_127 */ |
| >; |
| }; |
| }; |
| |
| &wkup_pmx0 { |
| wkup_uart0_pins_default: wkup-uart0-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0xa0, PIN_INPUT, 0) /* (J29) WKUP_UART0_RXD */ |
| J721E_WKUP_IOPAD(0xa4, PIN_OUTPUT, 0) /* (J28) WKUP_UART0_TXD */ |
| >; |
| }; |
| |
| mcu_uart0_pins_default: mcu-uart0-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0xe8, PIN_INPUT, 0) /* (H29) WKUP_GPIO0_14.MCU_UART0_CTSn */ |
| J721E_WKUP_IOPAD(0xec, PIN_OUTPUT, 0) /* (J27) WKUP_GPIO0_15.MCU_UART0_RTSn */ |
| J721E_WKUP_IOPAD(0xe4, PIN_INPUT, 0) /* (H28) WKUP_GPIO0_13.MCU_UART0_RXD */ |
| J721E_WKUP_IOPAD(0xe0, PIN_OUTPUT, 0) /* (G29) WKUP_GPIO0_12.MCU_UART0_TXD */ |
| >; |
| }; |
| |
| sw11_button_pins_default: sw11-button-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */ |
| >; |
| }; |
| |
| mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0x34, PIN_OUTPUT, 0) /* (F22) MCU_OSPI1_CLK */ |
| J721E_WKUP_IOPAD(0x50, PIN_OUTPUT, 0) /* (C22) MCU_OSPI1_CSn0 */ |
| J721E_WKUP_IOPAD(0x40, PIN_INPUT, 0) /* (D22) MCU_OSPI1_D0 */ |
| J721E_WKUP_IOPAD(0x44, PIN_INPUT, 0) /* (G22) MCU_OSPI1_D1 */ |
| J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (D23) MCU_OSPI1_D2 */ |
| J721E_WKUP_IOPAD(0x4c, PIN_INPUT, 0) /* (C23) MCU_OSPI1_D3 */ |
| J721E_WKUP_IOPAD(0x3c, PIN_INPUT, 0) /* (B23) MCU_OSPI1_DQS */ |
| J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */ |
| >; |
| }; |
| |
| mcu_cpsw_pins_default: mcu-cpsw-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */ |
| J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */ |
| J721E_WKUP_IOPAD(0x0060, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */ |
| J721E_WKUP_IOPAD(0x0064, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */ |
| J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */ |
| J721E_WKUP_IOPAD(0x006c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */ |
| J721E_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */ |
| J721E_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */ |
| J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */ |
| J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */ |
| J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */ |
| J721E_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* MCU_RGMII1_RXC */ |
| >; |
| }; |
| |
| mcu_mdio_pins_default: mcu-mdio1-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */ |
| J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */ |
| >; |
| }; |
| |
| mcu_mcan0_pins_default: mcu-mcan0-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0xac, PIN_INPUT, 0) /* (C29) MCU_MCAN0_RX */ |
| J721E_WKUP_IOPAD(0xa8, PIN_OUTPUT, 0) /* (D29) MCU_MCAN0_TX */ |
| >; |
| }; |
| |
| mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0xb0, PIN_INPUT, 7) /* (F26) WKUP_GPIO0_0 */ |
| J721E_WKUP_IOPAD(0x98, PIN_INPUT, 7) /* (E28) MCU_SPI0_D1.WKUP_GPIO0_54 */ |
| >; |
| }; |
| |
| mcu_mcan1_pins_default: mcu-mcan1-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0xc4, PIN_INPUT, 0) /* (G24) WKUP_GPIO0_5.MCU_MCAN1_RX */ |
| J721E_WKUP_IOPAD(0xc0, PIN_OUTPUT, 0) /* (G25) WKUP_GPIO0_4.MCU_MCAN1_TX */ |
| >; |
| }; |
| |
| mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0xb8, PIN_INPUT, 7) /* (F28) WKUP_GPIO0_2 */ |
| >; |
| }; |
| |
| wkup_gpio_pins_default: wkup-gpio-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0xd0, PIN_INPUT, 7) /* (C14) WKUP_GPIO0_8 */ |
| >; |
| }; |
| }; |
| |
| &wkup_uart0 { |
| /* Wakeup UART is used by System firmware */ |
| status = "reserved"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wkup_uart0_pins_default>; |
| }; |
| |
| &mcu_uart0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcu_uart0_pins_default>; |
| }; |
| |
| &main_uart0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_uart0_pins_default>; |
| /* Shared with ATF on this platform */ |
| power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>; |
| }; |
| |
| &main_uart1 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_uart1_pins_default>; |
| }; |
| |
| &main_uart2 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_uart2_pins_default>; |
| }; |
| |
| &main_uart4 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_uart4_pins_default>; |
| }; |
| |
| &wkup_gpio0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wkup_gpio_pins_default>; |
| }; |
| |
| &main_gpio0 { |
| status = "okay"; |
| }; |
| |
| &main_gpio1 { |
| status = "okay"; |
| }; |
| |
| &main_sdhci0 { |
| /* eMMC */ |
| status = "okay"; |
| non-removable; |
| ti,driver-strength-ohm = <50>; |
| disable-wp; |
| }; |
| |
| &main_sdhci1 { |
| /* SD/MMC */ |
| status = "okay"; |
| vmmc-supply = <&vdd_mmc1>; |
| vqmmc-supply = <&vdd_sd_dv_alt>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_mmc1_pins_default>; |
| ti,driver-strength-ohm = <50>; |
| disable-wp; |
| }; |
| |
| &usb_serdes_mux { |
| idle-states = <1>, <0>; /* USB0 to SERDES3, USB1 to SERDES1 */ |
| }; |
| |
| &serdes_ln_ctrl { |
| idle-states = <J721E_SERDES0_LANE0_PCIE0_LANE0>, <J721E_SERDES0_LANE1_PCIE0_LANE1>, |
| <J721E_SERDES1_LANE0_PCIE1_LANE0>, <J721E_SERDES1_LANE1_PCIE1_LANE1>, |
| <J721E_SERDES2_LANE0_PCIE2_LANE0>, <J721E_SERDES2_LANE1_PCIE2_LANE1>, |
| <J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>, |
| <J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>, |
| <J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>; |
| }; |
| |
| &serdes_wiz3 { |
| typec-dir-gpios = <&main_gpio1 3 GPIO_ACTIVE_HIGH>; |
| typec-dir-debounce-ms = <700>; /* TUSB321, tCCB_DEFAULT 133 ms */ |
| }; |
| |
| &serdes3 { |
| serdes3_usb_link: phy@0 { |
| reg = <0>; |
| cdns,num-lanes = <2>; |
| #phy-cells = <0>; |
| cdns,phy-type = <PHY_TYPE_USB3>; |
| resets = <&serdes_wiz3 1>, <&serdes_wiz3 2>; |
| }; |
| }; |
| |
| &usbss0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_usbss0_pins_default>; |
| ti,vbus-divider; |
| }; |
| |
| &usb0 { |
| dr_mode = "otg"; |
| maximum-speed = "super-speed"; |
| phys = <&serdes3_usb_link>; |
| phy-names = "cdns3,usb3-phy"; |
| }; |
| |
| &usbss1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_usbss1_pins_default>; |
| ti,usb2-only; |
| }; |
| |
| &usb1 { |
| dr_mode = "host"; |
| maximum-speed = "high-speed"; |
| }; |
| |
| &ospi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcu_fss0_ospi1_pins_default>; |
| |
| flash@0 { |
| compatible = "jedec,spi-nor"; |
| reg = <0x0>; |
| spi-tx-bus-width = <1>; |
| spi-rx-bus-width = <4>; |
| spi-max-frequency = <40000000>; |
| cdns,tshsl-ns = <60>; |
| cdns,tsd2d-ns = <60>; |
| cdns,tchsh-ns = <60>; |
| cdns,tslch-ns = <60>; |
| cdns,read-delay = <2>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| label = "qspi.tiboot3"; |
| reg = <0x0 0x80000>; |
| }; |
| |
| partition@80000 { |
| label = "qspi.tispl"; |
| reg = <0x80000 0x200000>; |
| }; |
| |
| partition@280000 { |
| label = "qspi.u-boot"; |
| reg = <0x280000 0x400000>; |
| }; |
| |
| partition@680000 { |
| label = "qspi.env"; |
| reg = <0x680000 0x20000>; |
| }; |
| |
| partition@6a0000 { |
| label = "qspi.env.backup"; |
| reg = <0x6a0000 0x20000>; |
| }; |
| |
| partition@6c0000 { |
| label = "qspi.sysfw"; |
| reg = <0x6c0000 0x100000>; |
| }; |
| |
| partition@800000 { |
| label = "qspi.rootfs"; |
| reg = <0x800000 0x37c0000>; |
| }; |
| |
| partition@3fe0000 { |
| label = "qspi.phypattern"; |
| reg = <0x3fe0000 0x20000>; |
| }; |
| }; |
| }; |
| }; |
| |
| &tscadc0 { |
| status = "okay"; |
| adc { |
| ti,adc-channels = <0 1 2 3 4 5 6 7>; |
| }; |
| }; |
| |
| &tscadc1 { |
| status = "okay"; |
| adc { |
| ti,adc-channels = <0 1 2 3 4 5 6 7>; |
| }; |
| }; |
| |
| &main_i2c0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_i2c0_pins_default>; |
| clock-frequency = <400000>; |
| |
| exp1: gpio@20 { |
| compatible = "ti,tca6416"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| exp2: gpio@22 { |
| compatible = "ti,tca6424"; |
| reg = <0x22>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| p09-hog { |
| /* P11 - MCASP/TRACE_MUX_S0 */ |
| gpio-hog; |
| gpios = <9 GPIO_ACTIVE_HIGH>; |
| output-low; |
| line-name = "MCASP/TRACE_MUX_S0"; |
| }; |
| |
| p10-hog { |
| /* P12 - MCASP/TRACE_MUX_S1 */ |
| gpio-hog; |
| gpios = <10 GPIO_ACTIVE_HIGH>; |
| output-high; |
| line-name = "MCASP/TRACE_MUX_S1"; |
| }; |
| }; |
| }; |
| |
| &main_i2c1 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_i2c1_pins_default>; |
| clock-frequency = <400000>; |
| |
| exp4: gpio@20 { |
| compatible = "ti,tca6408"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_i2c1_exp4_pins_default>; |
| interrupt-parent = <&main_gpio1>; |
| interrupts = <11 IRQ_TYPE_EDGE_FALLING>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| &k3_clks { |
| /* Confiure AUDIO_EXT_REFCLK2 pin as output */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&audi_ext_refclk2_pins_default>; |
| }; |
| |
| &main_i2c3 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_i2c3_pins_default>; |
| clock-frequency = <400000>; |
| |
| exp3: gpio@20 { |
| compatible = "ti,tca6408"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| pcm3168a_1: audio-codec@44 { |
| compatible = "ti,pcm3168a"; |
| reg = <0x44>; |
| |
| #sound-dai-cells = <1>; |
| |
| reset-gpios = <&exp3 0 GPIO_ACTIVE_LOW>; |
| |
| /* C_AUDIO_REFCLK2 -> RGMII6_RXC (W26) */ |
| clocks = <&k3_clks 157 371>; |
| clock-names = "scki"; |
| |
| /* HSDIV3_16FFT_MAIN_4_HSDIVOUT2_CLK -> REFCLK2 */ |
| assigned-clocks = <&k3_clks 157 371>; |
| assigned-clock-parents = <&k3_clks 157 400>; |
| assigned-clock-rates = <24576000>; /* for 48KHz */ |
| |
| VDD1-supply = <&vsys_3v3>; |
| VDD2-supply = <&vsys_3v3>; |
| VCCAD1-supply = <&vsys_5v0>; |
| VCCAD2-supply = <&vsys_5v0>; |
| VCCDA1-supply = <&vsys_5v0>; |
| VCCDA2-supply = <&vsys_5v0>; |
| }; |
| }; |
| |
| &main_i2c6 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_i2c6_pins_default>; |
| clock-frequency = <400000>; |
| |
| exp5: gpio@20 { |
| compatible = "ti,tca6408"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| &mcu_cpsw { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcu_cpsw_pins_default>, <&mcu_mdio_pins_default>; |
| }; |
| |
| &davinci_mdio { |
| phy0: ethernet-phy@0 { |
| reg = <0>; |
| ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; |
| ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; |
| }; |
| }; |
| |
| &cpsw_port1 { |
| phy-mode = "rgmii-rxid"; |
| phy-handle = <&phy0>; |
| }; |
| |
| &dss { |
| /* |
| * These clock assignments are chosen to enable the following outputs: |
| * |
| * VP0 - DisplayPort SST |
| * VP1 - DPI0 |
| * VP2 - DSI |
| * VP3 - DPI1 |
| */ |
| |
| assigned-clocks = <&k3_clks 152 1>, |
| <&k3_clks 152 4>, |
| <&k3_clks 152 9>, |
| <&k3_clks 152 13>; |
| assigned-clock-parents = <&k3_clks 152 2>, /* PLL16_HSDIV0 */ |
| <&k3_clks 152 6>, /* PLL19_HSDIV0 */ |
| <&k3_clks 152 11>, /* PLL18_HSDIV0 */ |
| <&k3_clks 152 18>; /* PLL23_HSDIV0 */ |
| }; |
| |
| &dss_ports { |
| port { |
| dpi0_out: endpoint { |
| remote-endpoint = <&dp0_in>; |
| }; |
| }; |
| }; |
| |
| &dp0_ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| dp0_in: endpoint { |
| remote-endpoint = <&dpi0_out>; |
| }; |
| }; |
| |
| port@4 { |
| reg = <4>; |
| dp0_out: endpoint { |
| remote-endpoint = <&dp_connector_in>; |
| }; |
| }; |
| }; |
| |
| &mcasp10 { |
| status = "okay"; |
| #sound-dai-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcasp10_pins_default>; |
| |
| op-mode = <0>; /* MCASP_IIS_MODE */ |
| tdm-slots = <2>; |
| auxclk-fs-ratio = <256>; |
| |
| serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ |
| 1 1 1 1 |
| 2 2 2 0 |
| >; |
| tx-num-evt = <0>; |
| rx-num-evt = <0>; |
| }; |
| |
| &cmn_refclk1 { |
| clock-frequency = <100000000>; |
| }; |
| |
| &wiz0_pll1_refclk { |
| assigned-clocks = <&wiz0_pll1_refclk>; |
| assigned-clock-parents = <&cmn_refclk1>; |
| }; |
| |
| &wiz0_refclk_dig { |
| assigned-clocks = <&wiz0_refclk_dig>; |
| assigned-clock-parents = <&cmn_refclk1>; |
| }; |
| |
| &wiz1_pll1_refclk { |
| assigned-clocks = <&wiz1_pll1_refclk>; |
| assigned-clock-parents = <&cmn_refclk1>; |
| }; |
| |
| &wiz1_refclk_dig { |
| assigned-clocks = <&wiz1_refclk_dig>; |
| assigned-clock-parents = <&cmn_refclk1>; |
| }; |
| |
| &wiz2_pll1_refclk { |
| assigned-clocks = <&wiz2_pll1_refclk>; |
| assigned-clock-parents = <&cmn_refclk1>; |
| }; |
| |
| &wiz2_refclk_dig { |
| assigned-clocks = <&wiz2_refclk_dig>; |
| assigned-clock-parents = <&cmn_refclk1>; |
| }; |
| |
| &serdes0 { |
| assigned-clocks = <&serdes0 CDNS_SIERRA_PLL_CMNLC>; |
| assigned-clock-parents = <&wiz0_pll1_refclk>; |
| |
| serdes0_pcie_link: phy@0 { |
| reg = <0>; |
| cdns,num-lanes = <1>; |
| #phy-cells = <0>; |
| cdns,phy-type = <PHY_TYPE_PCIE>; |
| resets = <&serdes_wiz0 1>; |
| }; |
| }; |
| |
| &serdes1 { |
| assigned-clocks = <&serdes1 CDNS_SIERRA_PLL_CMNLC>; |
| assigned-clock-parents = <&wiz1_pll1_refclk>; |
| |
| serdes1_pcie_link: phy@0 { |
| reg = <0>; |
| cdns,num-lanes = <2>; |
| #phy-cells = <0>; |
| cdns,phy-type = <PHY_TYPE_PCIE>; |
| resets = <&serdes_wiz1 1>, <&serdes_wiz1 2>; |
| }; |
| }; |
| |
| &serdes2 { |
| assigned-clocks = <&serdes2 CDNS_SIERRA_PLL_CMNLC>; |
| assigned-clock-parents = <&wiz2_pll1_refclk>; |
| |
| serdes2_pcie_link: phy@0 { |
| reg = <0>; |
| cdns,num-lanes = <2>; |
| #phy-cells = <0>; |
| cdns,phy-type = <PHY_TYPE_PCIE>; |
| resets = <&serdes_wiz2 1>, <&serdes_wiz2 2>; |
| }; |
| }; |
| |
| &serdes4 { |
| torrent_phy_dp: phy@0 { |
| reg = <0>; |
| resets = <&serdes_wiz4 1>; |
| cdns,phy-type = <PHY_TYPE_DP>; |
| cdns,num-lanes = <4>; |
| cdns,max-bit-rate = <5400>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| &mhdp { |
| phys = <&torrent_phy_dp>; |
| phy-names = "dpphy"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&dp0_pins_default>; |
| }; |
| |
| &pcie0_rc { |
| status = "okay"; |
| reset-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>; |
| phys = <&serdes0_pcie_link>; |
| phy-names = "pcie-phy"; |
| num-lanes = <1>; |
| }; |
| |
| &pcie1_rc { |
| status = "okay"; |
| reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>; |
| phys = <&serdes1_pcie_link>; |
| phy-names = "pcie-phy"; |
| num-lanes = <2>; |
| }; |
| |
| &pcie2_rc { |
| status = "okay"; |
| reset-gpios = <&exp2 20 GPIO_ACTIVE_HIGH>; |
| phys = <&serdes2_pcie_link>; |
| phy-names = "pcie-phy"; |
| num-lanes = <2>; |
| }; |
| |
| &mcu_mcan0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcu_mcan0_pins_default>; |
| phys = <&transceiver1>; |
| }; |
| |
| &mcu_mcan1 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcu_mcan1_pins_default>; |
| phys = <&transceiver2>; |
| }; |
| |
| &main_mcan0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_mcan0_pins_default>; |
| phys = <&transceiver3>; |
| }; |
| |
| &main_mcan2 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_mcan2_pins_default>; |
| phys = <&transceiver4>; |
| }; |
