| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright 2020 Gateworks Corporation |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/phy/phy-imx8-pcie.h> |
| |
| / { |
| aliases { |
| ethernet1 = ð1; |
| usb0 = &usbotg1; |
| usb1 = &usbotg2; |
| }; |
| |
| led-controller { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_leds>; |
| |
| led-0 { |
| function = LED_FUNCTION_STATUS; |
| color = <LED_COLOR_ID_GREEN>; |
| gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; |
| default-state = "on"; |
| linux,default-trigger = "heartbeat"; |
| }; |
| |
| led-1 { |
| function = LED_FUNCTION_STATUS; |
| color = <LED_COLOR_ID_RED>; |
| gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; |
| default-state = "off"; |
| }; |
| }; |
| |
| pcie0_refclk: pcie0-refclk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <100000000>; |
| }; |
| |
| pps { |
| compatible = "pps-gpio"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pps>; |
| gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| reg_1p8v: regulator-1p8v { |
| compatible = "regulator-fixed"; |
| regulator-name = "1P8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| |
| reg_3p3v: regulator-3p3v { |
| compatible = "regulator-fixed"; |
| regulator-name = "3P3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| reg_usb_otg1_vbus: regulator-usb-otg1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_reg_usb1_en>; |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_otg1_vbus"; |
| gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| reg_usb_otg2_vbus: regulator-usb-otg2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_reg_usb2_en>; |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_otg2_vbus"; |
| gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| reg_wifi_en: regulator-wifi-en { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_reg_wl>; |
| compatible = "regulator-fixed"; |
| regulator-name = "wl"; |
| gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; |
| startup-delay-us = <100>; |
| enable-active-high; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| }; |
| |
| /* off-board header */ |
| &ecspi2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi2>; |
| cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>, |
| <&gpio1 10 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| |
| tpm@1 { |
| compatible = "atmel,attpm20p", "tcg,tpm_tis-spi"; |
| reg = <0x1>; |
| spi-max-frequency = <36000000>; |
| }; |
| }; |
| |
| &gpio1 { |
| gpio-line-names = "rs485_term", "mipi_gpio4", "", "", |
| "", "", "pci_usb_sel", "dio0", |
| "", "dio1", "", "", "", "", "", "", |
| "", "", "", "", "", "", "", "", |
| "", "", "", "", "", "", "", ""; |
| }; |
| |
| &gpio4 { |
| gpio-line-names = "rs485_en", "mipi_gpio3", "rs485_hd", "mipi_gpio2", |
| "mipi_gpio1", "", "", "pci_wdis#", |
| "", "", "", "", "", "", "", "", |
| "", "", "", "", "", "", "", "", |
| "", "", "", "", "", "", "", ""; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| status = "okay"; |
| |
| accelerometer@19 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_accel>; |
| compatible = "st,lis2de12"; |
| reg = <0x19>; |
| st,drdy-int-pin = <1>; |
| interrupt-parent = <&gpio4>; |
| interrupts = <5 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| }; |
| |
| /* off-board header */ |
| &i2c3 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| status = "okay"; |
| }; |
| |
| &pcie_phy { |
| fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>; |
| fsl,clkreq-unsupported; |
| clocks = <&pcie0_refclk>; |
| clock-names = "ref"; |
| status = "okay"; |
| }; |
| |
| &pcie0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcie0>; |
| reset-gpio = <&gpio4 6 GPIO_ACTIVE_LOW>; |
| clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>, |
| <&clk IMX8MM_CLK_PCIE1_AUX>; |
| assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, |
| <&clk IMX8MM_CLK_PCIE1_CTRL>; |
| assigned-clock-rates = <10000000>, <250000000>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, |
| <&clk IMX8MM_SYS_PLL2_250M>; |
| status = "okay"; |
| |
| pcie@0,0 { |
| reg = <0x0000 0 0 0 0>; |
| device_type = "pci"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| pcie@0,0 { |
| reg = <0x0000 0 0 0 0>; |
| device_type = "pci"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| pcie@4,0 { |
| reg = <0x2000 0 0 0 0>; |
| device_type = "pci"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| eth1: ethernet@0,0 { |
| reg = <0x0000 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| local-mac-address = [00 00 00 00 00 00]; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| /* off-board header */ |
| &sai3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sai3>; |
| assigned-clocks = <&clk IMX8MM_CLK_SAI3>; |
| assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; |
| assigned-clock-rates = <24576000>; |
| status = "okay"; |
| }; |
| |
| /* GPS */ |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| }; |
| |
| /* bluetooth HCI */ |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_bten>; |
| cts-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; |
| rts-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "brcm,bcm4330-bt"; |
| shutdown-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| /* RS232 */ |
| &uart4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart4>; |
| status = "okay"; |
| }; |
| |
| &usbotg1 { |
| dr_mode = "otg"; |
| over-current-active-low; |
| vbus-supply = <®_usb_otg1_vbus>; |
| status = "okay"; |
| }; |
| |
| &usbotg2 { |
| dr_mode = "host"; |
| disable-over-current; |
| vbus-supply = <®_usb_otg2_vbus>; |
| status = "okay"; |
| }; |
| |
| /* SDIO WiFi */ |
| &usdhc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| bus-width = <4>; |
| non-removable; |
| vmmc-supply = <®_wifi_en>; |
| status = "okay"; |
| }; |
| |
| /* microSD */ |
| &usdhc2 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; |
| cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; |
| bus-width = <4>; |
| vmmc-supply = <®_3p3v>; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_hog>; |
| |
| pinctrl_hog: hoggrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */ |
| MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */ |
| MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */ |
| MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */ |
| MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */ |
| MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x40000104 /* RS485_TERM */ |
| MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x40000104 /* RS485 */ |
| MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2 0x40000104 /* RS485_HALF */ |
| >; |
| }; |
| |
| pinctrl_accel: accelgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159 |
| >; |
| }; |
| |
| pinctrl_bten: btengrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 |
| >; |
| }; |
| |
| pinctrl_gpio_leds: gpioledgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19 |
| MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 |
| MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_pcie0: pcie0grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6 0x41 |
| >; |
| }; |
| |
| pinctrl_pps: ppsgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 |
| >; |
| }; |
| |
| pinctrl_reg_wl: regwlgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x41 |
| >; |
| }; |
| |
| pinctrl_reg_usb1_en: regusb1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41 |
| MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41 |
| >; |
| }; |
| |
| pinctrl_reg_usb2_en: regusb2grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x41 |
| >; |
| }; |
| |
| pinctrl_sai3: sai3grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 |
| MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 |
| MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6 |
| MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 |
| MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6 |
| >; |
| }; |
| |
| pinctrl_spi2: spi2grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 |
| MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6 |
| MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0xd6 |
| MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6 |
| MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0xd6 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 |
| MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 |
| MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 |
| MX8MM_IOMUXC_ECSPI1_MISO_GPIO5_IO8 0x140 |
| MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x140 |
| >; |
| }; |
| |
| pinctrl_uart4: uart4grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140 |
| MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 |
| MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 |
| MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 |
| MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 |
| >; |
| }; |
| |
| pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 |
| MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 |
| >; |
| }; |
| |
| pinctrl_usdhc2_gpio: usdhc2gpiogrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4 |
| MX8MM_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0x1d0 |
| MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| }; |
