arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts - linux - Git at Google

 // SPDX-License-Identifier: GPL-2.0
 /*
  * dts file for Hisilicon HiKey970 Development Board
  *
  * Copyright (C) 2016, HiSilicon Ltd.
  * Copyright (C) 2018, Linaro Ltd.
  *
  */

 /dts-v1/;
 #include <dt-bindings/gpio/gpio.h>

 #include "hi3670.dtsi"
 #include "hikey970-pinctrl.dtsi"
 #include "hikey970-pmic.dtsi"

 / {
 	model = "HiKey970";
 	compatible = "hisilicon,hi3670-hikey970", "hisilicon,hi3670";

 	aliases {
 		mshc1 = &dwmmc1;
 		mshc2 = &dwmmc2;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &uart2;
 		serial3 = &uart3;
 		serial4 = &uart4;
 		serial5 = &uart5;
 		serial6 = &uart6;       /* console UART */
 	};

 	chosen {
 		stdout-path = "serial6:115200n8";
 	};

 	memory@0 {
 		device_type = "memory";
 		/* expect bootloader to fill in this region */
 		reg = <0x0 0x0 0x0 0x0>;
 	};

 	wlan_en: wlan-en-1-8v {
 		compatible = "regulator-fixed";
 		regulator-name = "wlan-en-regulator";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;

 		/* GPIO_051_WIFI_EN */
 		gpio = <&gpio6 3 0>;

 		/* WLAN card specific delay */
 		startup-delay-us = <70000>;
 		enable-active-high;
 	};
 };

 /*
  * Legend: proper name = the GPIO line is used as GPIO
  *         NC = not connected (pin out but not routed from the chip to
  *              anything the board)
  *         "[PER]" = pin is muxed for [peripheral] (not GPIO)
  *         "" = no idea, schematic doesn't say, could be
  *              unrouted (not connected to any external pin)
  *         LSEC = Low Speed External Connector
  *         HSEC = High Speed External Connector
  *
  * Line names are taken from "hikey970-schematics.pdf" from HiSilicon.
  *
  * For the lines routed to the external connectors the
  * lines are named after the 96Boards CE Specification 1.0,
  * Appendix "Expansion Connector Signal Description".
  *
  * When the 96Board naming of a line and the schematic name of
  * the same line are in conflict, the 96Board specification
  * takes precedence, which means that the external UART on the
  * LSEC is named UART0 while the schematic and SoC names this
  * UART2. This is only for the informational lines i.e. "[FOO]",
  * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
  * ones actually used for GPIO.
  */
 &gpio0 {
 	/* GPIO_000-GPIO_007 */
 	gpio-line-names =
 		"",
 		"TP901", /* TEST_MODE connected to TP901 */
 		"",
 		"GPIO_003_USB_HUB_RESET_N",
 		"NC",
 		"[AP_GPS_REF_CLK]",
 		"[I2C3_SCL]",
 		"[I2C3_SDA]";
 };

 &gpio1 {
 	/* GPIO_008-GPIO_015 */
 	gpio-line-names =
 		"[UART0_CTS]", /* LSEC pin 3: GPIO_008_UART2_CTS_N */
 		"[UART0_RTS]", /* LSEC pin 9: GPIO_009_UART2_RTS_N */
 		"[UART0_TXD]", /* LSEC pin 5: GPIO_010_UART2_TXD */
 		"[UART0_RXD]", /* LSEC pin 7: GPIO_011_UART2_RXD */
 		"[USER_LED5]",
 		"GPIO-I", /* LSEC pin 31: GPIO_013_CAM0_RST_N */
 		"[USER_LED3]",
 		"[USER_LED4]";
 };

 &gpio2 {
 	/* GPIO_016-GPIO_023 */
 	gpio-line-names =
 		"GPIO-G", /* LSEC pin 29: GPIO_016_LCD_TE0 */
 		"[CSI0_MCLK]", /* HSEC pin 15: ISP_CCLK0_MCAM */
 		"[CSI1_MCLK]", /* HSEC pin 17: ISP_CCLK1_SCAM */
 		"GPIO_019_BT_ACTIVE",
 		"[I2C2_SCL]", /* HSEC pin 32: ISP_SCL0 */
 		"[I2C2_SDA]", /* HSEC pin 34: ISP_SDA0 */
 		"[I2C3_SCL]", /* HSEC pin 36: ISP_SCL1 */
 		"[I2C3_SDA]"; /* HSEC pin 38: ISP_SDA1 */
 };

 &gpio3 {
 	/* GPIO_024-GPIO_031 */
 	gpio-line-names =
 		"GPIO_024_WIFI_ACTIVE",
 		"GPIO_025_PERST_M.2",
 		"[I2C4_SCL]",
 		"[I2C4_SDA]",
 		"NC",
 		"GPIO-H", /* LSEC pin 30: GPIO_029_LCD_RST_N */
 		"[USER_LED1]",
 		"GPIO-L"; /* LSEC pin 34: GPIO_031 */
 };

 &gpio4 {
 	/* GPIO_032-GPIO_039 */
 	gpio-line-names =
 		"GPIO-K", /* LSEC pin 33: GPIO_032_CAM1_RST_N */
 		"GPIO_033_PMU1_EN",
 		"GPIO_034_USBSW_SEL",
 		/*
 		 * These two pins should be used for SD(IO) data according
 		 * to the 96boards specification but seems to be repurposed
 		 * for UART 0. They are however named according to the spec.
 		 */
 		"[SD_DAT1]", /* HSEC pin 3: GPIO_035_UART0_RXD */
 		"[SD_DAT2]", /* HSEC pin 5: GPIO_036_UART0_TXD */
 		"[UART1_RXD]", /* LSEC pin 13: DEBUG_UART6_RXD */
 		"[UART1_TXD]", /* LSEC pin 11: DEBUG_UART6_TXD */
 		"[SOC_GPS_UART3_CTS_N]"; /* TP2304 */
 };

 &gpio5 {
 	/* GPIO_040-GPIO_047 */
 	gpio-line-names =
 		"[SOC_GPS_UART3_RTS_N]", /* TP2302 */
 		"[SOC_GPS_UART3_RXD]", /* TP2303 */
 		"[SOC_GPS_UART3_TXD]", /* TP2305 */
 		"[SOC_BT_UART4_CTS_N]",
 		"[SOC_BT_UART4_RTS_N]",
 		"[SOC_BT_UART4_RXD]",
 		"[SOC_BT_UART4_TXD]",
 		"NC";
 };

 &gpio6 {
 	/* GPIO_048-GPIO_055 */
 	gpio-line-names =
 		"NC",
 		"GPIO_049_USER_LED6",
 		"GPIO_050_CAN_RST",
 		"GPIO_051_WIFI_EN",
 		"GPIO-D", /* LSEC pin 26 */
 		"GPIO-J", /* LSEC pin 32 */
 		"GPIO_054_BT_EN",
 		"[GPIO_055_SEL]";
 };

 &gpio7 {
 	/* GPIO_056-GPIO_063 */
 	gpio-line-names =
 		"[PCIE_PERST_L]", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
 };

 &gpio8 {
 	/* GPIO_064-GPIO_071 */
 	gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
 };

 &gpio9 {
 	/* GPIO_072-GPIO_079 */
 	gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
 };

 &gpio10 {
 	/* GPIO_080-GPIO_087 */
 	gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
 };

 &gpio11 {
 	/* GPIO_088-GPIO_095 */
 	gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
 };

 &gpio12 {
 	/* GPIO_096-GPIO_103 */
 	gpio-line-names = "NC", "", "", "", "", "", "", "";
 };

 &gpio13 {
 	/* GPIO_104-GPIO_111 */
 	gpio-line-names = "", "", "", "", "", "", "", "";
 };

 &gpio14 {
 	/* GPIO_112-GPIO_119 */
 	gpio-line-names = "", "", "", "", "", "", "", "";
 };

 &gpio15 {
 	/* GPIO_120-GPIO_127 */
 	gpio-line-names = "", "", "", "", "", "", "", "";
 };

 &gpio16 {
 	/* GPIO_128-GPIO_135 */
 	gpio-line-names =
 		"[WL_SDIO_CLK]",
 		"[WL_SDIO_CMD]",
 		"[WL_SDIO_DATA0]",
 		"[WL_SDIO_DATA1]",
 		"[WL_SDIO_DATA2]",
 		"[WL_SDIO_DATA3]",
 		"[ETH_ISOLATE]",
 		"NC";
 };

 &gpio17 {
 	/* GPIO_136-GPIO_143 */
 	gpio-line-names =
 		"[MINI1CLK_EN]", "NC", "", "", "", "", "", "";
 };

 &gpio18 {
 	/* GPIO_144-GPIO_151 */
 	gpio-line-names =
 		"[SPI1_SCLK]", /* HSEC pin 9: GPIO_144_SPI3_CLK */
 		"[SPI1_DIN]", /* HSEC pin 11: GPIO_145_SPI3_DI */
 		"[SPI1_DOUT]", /* HSEC pin 1: GPIO_146_SPI3_DO */
 		"[SPI1_CS]", /* HSEC pin 7: GPIO_147_SPI3_CS0_N */
 		"[POWER_INT_N]",
 		"[CDMA_GPS_SYNC]",
 		"GPIO_150_PEX_INTA",
 		"GPIO_151_CAN_INT";
 };

 &gpio19 {
 	/* GPIO_152-GPIO_159 */
 	gpio-line-names = "", "", "", "", "", "", "", "";
 };

 &gpio20 {
 	/* GPIO_160-GPIO_167 */
 	gpio-line-names =
 		"[SD_CLK]",
 		"[SD_CMD]",
 		"[SD_DATA0]",
 		"[SD_DATA1]",
 		"[SD_DATA2]",
 		"[SD_DATA3]",
 		"GPIO_166_ETHCLK_EN",
 		"GPIO_167_USER_LED2";
 };

 &gpio21 {
 	/* GPIO_168-GPIO_175 */
 	gpio-line-names =
 		"GPIO_168_GPS_EN",
 		"GPIO-C", /* LSEC pin 25: GPIO_169_USIM1_CLK */
 		"GPIO-E", /* LSEC pin 27: GPIO_170_USIM1_RST */
 		"GPIO-B", /* LSEC pin 24: GPIO_171_USIM1_DATA */
 		"", "", "", "", "";
 };

 &gpio22 {
 	/* GPIO_176-GPIO_183 */
 	gpio-line-names =
 		"[PMU_PWR_HOLD]",
 		"GPIO_177_WL_WAKEUP_AP",
 		"[JTAG_TCK]",
 		"[JTAG_TMS]",
 		"[JTAG_TDI]",
 		"[JTAG_TMS]",
 		"GPIO_182_FATAL_ERR",
 		"NC";
 };

 &gpio23 {
 	/* GPIO_184-GPIO_191 */
 	gpio-line-names =
 		"GPIO_184_JTAG_SEL",
 		"GPIO-F", /* LSEC pin 28: GPIO_185_LCD_BL_PWM */
 		"[I2C0_SCL]", /* LSEC pin 15: GPIO_186_I2C0_SCL */
 		"[I2C0_SDA]", /* LSEC pin 17: GPIO_187_I2C0_SDA */
 		"[GPIO_188_I2C1_SCL]", /* Actual SoC I2C1_SCL */
 		"[GPIO_189_I2C1_SDA]", /* Actual SoC I2C1_SDA */
 		"[I2C1_SCL]", /* LSEC pin 19: GPIO_190_I2C2_SCL */
 		"[I2C2_SDA]"; /* LSEC pin 21: GPIO_191_I2C2_SDA */
 };

 &gpio24 {
 	/* GPIO_192-GPIO_199 */
 	gpio-line-names =
 		"[SD_LED]",
 		"NC",
 		"[PCM_DI]", /* LSEC pin 22: GPIO_194_I2S0_DI */
 		"[PCM_DO]", /* LSEC pin 20: GPIO_195_I2S0_DO */
 		"[PCM_CLK]", /* LSEC pin 18: GPIO_196_I2S0_XCLK */
 		"[PCM_FS]", /* LSEC pin 16: GPIO_197_I2S0_XFS */
 		"",
 		"[I2S2_DO]";
 };

 &gpio25 {
 	/* GPIO_200-GPIO_207 */
 	gpio-line-names =
 		"[I2S2_XCLK]",
 		"[I2S2_XFS]",
 		"GPIO_202_PERST_ETH",
 		"GPIO_203_PWRON_DET",
 		"GPIO_204_PMU1_IRQ_N",
 		"GPIO_205_SD_DET",
 		"GPIO_206_GPS_MOTION_INT",
 		"GPIO_207_HDMI_SEL";
 };

 &gpio26 {
 	/* GPIO_208-GPIO_215 */
 	gpio-line-names =
 		"GPIO-A", /* LSEC pin 23: GPIO_208_WAKEUP_SOC */
 		"GPIO_209_VBUS_TYPEC",
 		"NC",
 		"NC",
 		"NC",
 		"[SPI0_SCLK]", /* LSEC pin 8: GPIO_213_SPI2_CLK */
 		"[SPI0_DIN]", /* LSEC pin 10: GPIO_214_SPI2_DI */
 		"[SPI0_DOUT]"; /* LSEC pin 14: GPIO_215_SPI2_DO */
 };

 &gpio27 {
 	/* GPIO_216-GPIO_223 */
 	gpio-line-names =
 		"[SPI0_CS]", /* LSEC pin 12: GPIO_216_SPI2_CS0_N */
 		"GPIO_217_HDMI_PD",
 		"GPIO_218_GPS_WAKEUP_AP",
 		"GPIO_219_M.2CLK_EN",
 		"GPIO_220_PERST_MINI",
 		"GPIO_221_CC_INT",
 		"[PCIE_CLKREQ_L]",
 		"NC";
 };

 &gpio28 {
 	/* GPIO_224-GPIO_231 */
 	gpio-line-names =
 		"[PMU0_INT]",
 		"[SPMI_DATA]",
 		"[SPMI_CLK]",
 		"[CAN_SPI_CLK]",
 		"[CAN_SPI_DI]",
 		"[CAN_SPI_DO]",
 		"[CAN_SPI_CS]",
 		"GPIO_231_HDMI_INT";
 };

 &dwmmc1 {
 	bus-width = <0x4>;
 	sd-uhs-sdr12;
 	sd-uhs-sdr25;
 	sd-uhs-sdr50;
 	sd-uhs-sdr104;
 	cap-sd-highspeed;
 	disable-wp;
 	cd-inverted;
 	cd-gpios = <&gpio25 5 GPIO_ACTIVE_HIGH>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd_pmx_func
 		     &sd_clk_cfg_func
 		     &sd_cfg_func>;
 	vmmc-supply = <&ldo16>;
 	vqmmc-supply = <&ldo9>;
 	status = "okay";
 };

 &dwmmc2 { /* WIFI */
 	bus-width = <0x4>;
 	non-removable;
 	broken-cd;
 	cap-power-off-card;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdio_pmx_func
 		     &sdio_clk_cfg_func
 		     &sdio_cfg_func>;
 	/* WL_EN */
 	vmmc-supply = <&wlan_en>;
 	status = "okay";

 	wlcore: wlcore@2 {
 		compatible = "ti,wl1837";
 		reg = <2>;      /* sdio func num */
 		/* WL_IRQ, GPIO_177_WL_WAKEUP_AP */
 		interrupt-parent = <&gpio22>;
 		interrupts = <1 IRQ_TYPE_EDGE_RISING>;
 	};
 };

 &uart0 {
 	/* On High speed expansion header */
 	label = "HS-UART0";
 	status = "okay";
 };

 &uart2 {
 	/* On Low speed expansion header */
 	label = "LS-UART0";
 	status = "okay";
 };

 &uart6 {
 	/* On Low speed expansion header */
 	label = "LS-UART1";
 	status = "okay";
 };
	// SPDX-License-Identifier: GPL-2.0
	/*
	* dts file for Hisilicon HiKey970 Development Board
	*
	* Copyright (C) 2016, HiSilicon Ltd.
	* Copyright (C) 2018, Linaro Ltd.
	*
	*/

	/dts-v1/;
	#include <dt-bindings/gpio/gpio.h>

	#include "hi3670.dtsi"
	#include "hikey970-pinctrl.dtsi"
	#include "hikey970-pmic.dtsi"

	/ {
	model = "HiKey970";
	compatible = "hisilicon,hi3670-hikey970", "hisilicon,hi3670";

	aliases {
	mshc1 = &dwmmc1;
	mshc2 = &dwmmc2;
	serial0 = &uart0;
	serial1 = &uart1;
	serial2 = &uart2;
	serial3 = &uart3;
	serial4 = &uart4;
	serial5 = &uart5;
	serial6 = &uart6; /* console UART */
	};

	chosen {
	stdout-path = "serial6:115200n8";
	};

	memory@0 {
	device_type = "memory";
	/* expect bootloader to fill in this region */
	reg = <0x0 0x0 0x0 0x0>;
	};

	wlan_en: wlan-en-1-8v {
	compatible = "regulator-fixed";
	regulator-name = "wlan-en-regulator";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;

	/* GPIO_051_WIFI_EN */
	gpio = <&gpio6 3 0>;

	/* WLAN card specific delay */
	startup-delay-us = <70000>;
	enable-active-high;
	};
	};

	/*
	* Legend: proper name = the GPIO line is used as GPIO
	* NC = not connected (pin out but not routed from the chip to
	* anything the board)
	* "[PER]" = pin is muxed for [peripheral] (not GPIO)
	* "" = no idea, schematic doesn't say, could be
	* unrouted (not connected to any external pin)
	* LSEC = Low Speed External Connector
	* HSEC = High Speed External Connector
	*
	* Line names are taken from "hikey970-schematics.pdf" from HiSilicon.
	*
	* For the lines routed to the external connectors the
	* lines are named after the 96Boards CE Specification 1.0,
	* Appendix "Expansion Connector Signal Description".
	*
	* When the 96Board naming of a line and the schematic name of
	* the same line are in conflict, the 96Board specification
	* takes precedence, which means that the external UART on the
	* LSEC is named UART0 while the schematic and SoC names this
	* UART2. This is only for the informational lines i.e. "[FOO]",
	* the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
	* ones actually used for GPIO.
	*/
	&gpio0 {
	/* GPIO_000-GPIO_007 */
	gpio-line-names =
	"",
	"TP901", /* TEST_MODE connected to TP901 */
	"",
	"GPIO_003_USB_HUB_RESET_N",
	"NC",
	"[AP_GPS_REF_CLK]",
	"[I2C3_SCL]",
	"[I2C3_SDA]";
	};

	&gpio1 {
	/* GPIO_008-GPIO_015 */
	gpio-line-names =
	"[UART0_CTS]", /* LSEC pin 3: GPIO_008_UART2_CTS_N */
	"[UART0_RTS]", /* LSEC pin 9: GPIO_009_UART2_RTS_N */
	"[UART0_TXD]", /* LSEC pin 5: GPIO_010_UART2_TXD */
	"[UART0_RXD]", /* LSEC pin 7: GPIO_011_UART2_RXD */
	"[USER_LED5]",
	"GPIO-I", /* LSEC pin 31: GPIO_013_CAM0_RST_N */
	"[USER_LED3]",
	"[USER_LED4]";
	};

	&gpio2 {
	/* GPIO_016-GPIO_023 */
	gpio-line-names =
	"GPIO-G", /* LSEC pin 29: GPIO_016_LCD_TE0 */
	"[CSI0_MCLK]", /* HSEC pin 15: ISP_CCLK0_MCAM */
	"[CSI1_MCLK]", /* HSEC pin 17: ISP_CCLK1_SCAM */
	"GPIO_019_BT_ACTIVE",
	"[I2C2_SCL]", /* HSEC pin 32: ISP_SCL0 */
	"[I2C2_SDA]", /* HSEC pin 34: ISP_SDA0 */
	"[I2C3_SCL]", /* HSEC pin 36: ISP_SCL1 */
	"[I2C3_SDA]"; /* HSEC pin 38: ISP_SDA1 */
	};

	&gpio3 {
	/* GPIO_024-GPIO_031 */
	gpio-line-names =
	"GPIO_024_WIFI_ACTIVE",
	"GPIO_025_PERST_M.2",
	"[I2C4_SCL]",
	"[I2C4_SDA]",
	"NC",
	"GPIO-H", /* LSEC pin 30: GPIO_029_LCD_RST_N */
	"[USER_LED1]",
	"GPIO-L"; /* LSEC pin 34: GPIO_031 */
	};

	&gpio4 {
	/* GPIO_032-GPIO_039 */
	gpio-line-names =
	"GPIO-K", /* LSEC pin 33: GPIO_032_CAM1_RST_N */
	"GPIO_033_PMU1_EN",
	"GPIO_034_USBSW_SEL",
	/*
	* These two pins should be used for SD(IO) data according
	* to the 96boards specification but seems to be repurposed
	* for UART 0. They are however named according to the spec.
	*/
	"[SD_DAT1]", /* HSEC pin 3: GPIO_035_UART0_RXD */
	"[SD_DAT2]", /* HSEC pin 5: GPIO_036_UART0_TXD */
	"[UART1_RXD]", /* LSEC pin 13: DEBUG_UART6_RXD */
	"[UART1_TXD]", /* LSEC pin 11: DEBUG_UART6_TXD */
	"[SOC_GPS_UART3_CTS_N]"; /* TP2304 */
	};

	&gpio5 {
	/* GPIO_040-GPIO_047 */
	gpio-line-names =
	"[SOC_GPS_UART3_RTS_N]", /* TP2302 */
	"[SOC_GPS_UART3_RXD]", /* TP2303 */
	"[SOC_GPS_UART3_TXD]", /* TP2305 */
	"[SOC_BT_UART4_CTS_N]",
	"[SOC_BT_UART4_RTS_N]",
	"[SOC_BT_UART4_RXD]",
	"[SOC_BT_UART4_TXD]",
	"NC";
	};

	&gpio6 {
	/* GPIO_048-GPIO_055 */
	gpio-line-names =
	"NC",
	"GPIO_049_USER_LED6",
	"GPIO_050_CAN_RST",
	"GPIO_051_WIFI_EN",
	"GPIO-D", /* LSEC pin 26 */
	"GPIO-J", /* LSEC pin 32 */
	"GPIO_054_BT_EN",
	"[GPIO_055_SEL]";
	};

	&gpio7 {
	/* GPIO_056-GPIO_063 */
	gpio-line-names =
	"[PCIE_PERST_L]", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
	};

	&gpio8 {
	/* GPIO_064-GPIO_071 */
	gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
	};

	&gpio9 {
	/* GPIO_072-GPIO_079 */
	gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
	};

	&gpio10 {
	/* GPIO_080-GPIO_087 */
	gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
	};

	&gpio11 {
	/* GPIO_088-GPIO_095 */
	gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
	};

	&gpio12 {
	/* GPIO_096-GPIO_103 */
	gpio-line-names = "NC", "", "", "", "", "", "", "";
	};

	&gpio13 {
	/* GPIO_104-GPIO_111 */
	gpio-line-names = "", "", "", "", "", "", "", "";
	};

	&gpio14 {
	/* GPIO_112-GPIO_119 */
	gpio-line-names = "", "", "", "", "", "", "", "";
	};

	&gpio15 {
	/* GPIO_120-GPIO_127 */
	gpio-line-names = "", "", "", "", "", "", "", "";
	};

	&gpio16 {
	/* GPIO_128-GPIO_135 */
	gpio-line-names =
	"[WL_SDIO_CLK]",
	"[WL_SDIO_CMD]",
	"[WL_SDIO_DATA0]",
	"[WL_SDIO_DATA1]",
	"[WL_SDIO_DATA2]",
	"[WL_SDIO_DATA3]",
	"[ETH_ISOLATE]",
	"NC";
	};

	&gpio17 {
	/* GPIO_136-GPIO_143 */
	gpio-line-names =
	"[MINI1CLK_EN]", "NC", "", "", "", "", "", "";
	};

	&gpio18 {
	/* GPIO_144-GPIO_151 */
	gpio-line-names =
	"[SPI1_SCLK]", /* HSEC pin 9: GPIO_144_SPI3_CLK */
	"[SPI1_DIN]", /* HSEC pin 11: GPIO_145_SPI3_DI */
	"[SPI1_DOUT]", /* HSEC pin 1: GPIO_146_SPI3_DO */
	"[SPI1_CS]", /* HSEC pin 7: GPIO_147_SPI3_CS0_N */
	"[POWER_INT_N]",
	"[CDMA_GPS_SYNC]",
	"GPIO_150_PEX_INTA",
	"GPIO_151_CAN_INT";
	};

	&gpio19 {
	/* GPIO_152-GPIO_159 */
	gpio-line-names = "", "", "", "", "", "", "", "";
	};

	&gpio20 {
	/* GPIO_160-GPIO_167 */
	gpio-line-names =
	"[SD_CLK]",
	"[SD_CMD]",
	"[SD_DATA0]",
	"[SD_DATA1]",
	"[SD_DATA2]",
	"[SD_DATA3]",
	"GPIO_166_ETHCLK_EN",
	"GPIO_167_USER_LED2";
	};

	&gpio21 {
	/* GPIO_168-GPIO_175 */
	gpio-line-names =
	"GPIO_168_GPS_EN",
	"GPIO-C", /* LSEC pin 25: GPIO_169_USIM1_CLK */
	"GPIO-E", /* LSEC pin 27: GPIO_170_USIM1_RST */
	"GPIO-B", /* LSEC pin 24: GPIO_171_USIM1_DATA */
	"", "", "", "", "";
	};

	&gpio22 {
	/* GPIO_176-GPIO_183 */
	gpio-line-names =
	"[PMU_PWR_HOLD]",
	"GPIO_177_WL_WAKEUP_AP",
	"[JTAG_TCK]",
	"[JTAG_TMS]",
	"[JTAG_TDI]",
	"[JTAG_TMS]",
	"GPIO_182_FATAL_ERR",
	"NC";
	};

	&gpio23 {
	/* GPIO_184-GPIO_191 */
	gpio-line-names =
	"GPIO_184_JTAG_SEL",
	"GPIO-F", /* LSEC pin 28: GPIO_185_LCD_BL_PWM */
	"[I2C0_SCL]", /* LSEC pin 15: GPIO_186_I2C0_SCL */
	"[I2C0_SDA]", /* LSEC pin 17: GPIO_187_I2C0_SDA */
	"[GPIO_188_I2C1_SCL]", /* Actual SoC I2C1_SCL */
	"[GPIO_189_I2C1_SDA]", /* Actual SoC I2C1_SDA */
	"[I2C1_SCL]", /* LSEC pin 19: GPIO_190_I2C2_SCL */
	"[I2C2_SDA]"; /* LSEC pin 21: GPIO_191_I2C2_SDA */
	};

	&gpio24 {
	/* GPIO_192-GPIO_199 */
	gpio-line-names =
	"[SD_LED]",
	"NC",
	"[PCM_DI]", /* LSEC pin 22: GPIO_194_I2S0_DI */
	"[PCM_DO]", /* LSEC pin 20: GPIO_195_I2S0_DO */
	"[PCM_CLK]", /* LSEC pin 18: GPIO_196_I2S0_XCLK */
	"[PCM_FS]", /* LSEC pin 16: GPIO_197_I2S0_XFS */
	"",
	"[I2S2_DO]";
	};

	&gpio25 {
	/* GPIO_200-GPIO_207 */
	gpio-line-names =
	"[I2S2_XCLK]",
	"[I2S2_XFS]",
	"GPIO_202_PERST_ETH",
	"GPIO_203_PWRON_DET",
	"GPIO_204_PMU1_IRQ_N",
	"GPIO_205_SD_DET",
	"GPIO_206_GPS_MOTION_INT",
	"GPIO_207_HDMI_SEL";
	};

	&gpio26 {
	/* GPIO_208-GPIO_215 */
	gpio-line-names =
	"GPIO-A", /* LSEC pin 23: GPIO_208_WAKEUP_SOC */
	"GPIO_209_VBUS_TYPEC",
	"NC",
	"NC",
	"NC",
	"[SPI0_SCLK]", /* LSEC pin 8: GPIO_213_SPI2_CLK */
	"[SPI0_DIN]", /* LSEC pin 10: GPIO_214_SPI2_DI */
	"[SPI0_DOUT]"; /* LSEC pin 14: GPIO_215_SPI2_DO */
	};

	&gpio27 {
	/* GPIO_216-GPIO_223 */
	gpio-line-names =
	"[SPI0_CS]", /* LSEC pin 12: GPIO_216_SPI2_CS0_N */
	"GPIO_217_HDMI_PD",
	"GPIO_218_GPS_WAKEUP_AP",
	"GPIO_219_M.2CLK_EN",
	"GPIO_220_PERST_MINI",
	"GPIO_221_CC_INT",
	"[PCIE_CLKREQ_L]",
	"NC";
	};

	&gpio28 {
	/* GPIO_224-GPIO_231 */
	gpio-line-names =
	"[PMU0_INT]",
	"[SPMI_DATA]",
	"[SPMI_CLK]",
	"[CAN_SPI_CLK]",
	"[CAN_SPI_DI]",
	"[CAN_SPI_DO]",
	"[CAN_SPI_CS]",
	"GPIO_231_HDMI_INT";
	};

	&dwmmc1 {
	bus-width = <0x4>;
	sd-uhs-sdr12;
	sd-uhs-sdr25;
	sd-uhs-sdr50;
	sd-uhs-sdr104;
	cap-sd-highspeed;
	disable-wp;
	cd-inverted;
	cd-gpios = <&gpio25 5 GPIO_ACTIVE_HIGH>;
	pinctrl-names = "default";
	pinctrl-0 = <&sd_pmx_func
	&sd_clk_cfg_func
	&sd_cfg_func>;
	vmmc-supply = <&ldo16>;
	vqmmc-supply = <&ldo9>;
	status = "okay";
	};

	&dwmmc2 { /* WIFI */
	bus-width = <0x4>;
	non-removable;
	broken-cd;
	cap-power-off-card;
	pinctrl-names = "default";
	pinctrl-0 = <&sdio_pmx_func
	&sdio_clk_cfg_func
	&sdio_cfg_func>;
	/* WL_EN */
	vmmc-supply = <&wlan_en>;
	status = "okay";

	wlcore: wlcore@2 {
	compatible = "ti,wl1837";
	reg = <2>; /* sdio func num */
	/* WL_IRQ, GPIO_177_WL_WAKEUP_AP */
	interrupt-parent = <&gpio22>;
	interrupts = <1 IRQ_TYPE_EDGE_RISING>;
	};
	};

	&uart0 {
	/* On High speed expansion header */
	label = "HS-UART0";
	status = "okay";
	};

	&uart2 {
	/* On Low speed expansion header */
	label = "LS-UART0";
	status = "okay";
	};

	&uart6 {
	/* On Low speed expansion header */
	label = "LS-UART1";
	status = "okay";
	};