| // SPDX-License-Identifier: GPL-2.0 |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include <dt-bindings/sound/qcom,q6afe.h> |
| #include <dt-bindings/sound/qcom,q6asm.h> |
| #include "sdm845.dtsi" |
| #include "pm8998.dtsi" |
| #include "pmi8998.dtsi" |
| |
| /* |
| * Delete following upstream (sdm845.dtsi) reserved |
| * memory mappings which are different in this device. |
| */ |
| /delete-node/ &tz_mem; |
| /delete-node/ &adsp_mem; |
| /delete-node/ &wlan_msa_mem; |
| /delete-node/ &mpss_region; |
| /delete-node/ &venus_mem; |
| /delete-node/ &cdsp_mem; |
| /delete-node/ &mba_region; |
| /delete-node/ &slpi_mem; |
| /delete-node/ &spss_mem; |
| /delete-node/ &rmtfs_mem; |
| |
| / { |
| model = "Xiaomi Pocophone F1"; |
| compatible = "xiaomi,beryllium", "qcom,sdm845"; |
| |
| /* required for bootloader to select correct board */ |
| qcom,board-id = <69 0>; |
| qcom,msm-id = <321 0x20001>; |
| |
| aliases { |
| hsuart0 = &uart6; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| autorepeat; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vol_up_pin_a>; |
| |
| vol-up { |
| label = "Volume Up"; |
| linux,code = <KEY_VOLUMEUP>; |
| gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| /* Reserved memory changes from downstream */ |
| reserved-memory { |
| tz_mem: memory@86200000 { |
| reg = <0 0x86200000 0 0x4900000>; |
| no-map; |
| }; |
| |
| adsp_mem: memory@8c500000 { |
| reg = <0 0x8c500000 0 0x1e00000>; |
| no-map; |
| }; |
| |
| wlan_msa_mem: memory@8e300000 { |
| reg = <0 0x8e300000 0 0x100000>; |
| no-map; |
| }; |
| |
| mpss_region: memory@8e400000 { |
| reg = <0 0x8e400000 0 0x7800000>; |
| no-map; |
| }; |
| |
| venus_mem: memory@95c00000 { |
| reg = <0 0x95c00000 0 0x500000>; |
| no-map; |
| }; |
| |
| cdsp_mem: memory@96100000 { |
| reg = <0 0x96100000 0 0x800000>; |
| no-map; |
| }; |
| |
| mba_region: memory@96900000 { |
| reg = <0 0x96900000 0 0x200000>; |
| no-map; |
| }; |
| |
| slpi_mem: memory@96b00000 { |
| reg = <0 0x96b00000 0 0x1400000>; |
| no-map; |
| }; |
| |
| spss_mem: memory@97f00000 { |
| reg = <0 0x97f00000 0 0x100000>; |
| no-map; |
| }; |
| |
| rmtfs_mem: memory@f6301000 { |
| compatible = "qcom,rmtfs-mem"; |
| reg = <0 0xf6301000 0 0x200000>; |
| no-map; |
| |
| qcom,client-id = <1>; |
| qcom,vmid = <15>; |
| }; |
| }; |
| |
| vreg_s4a_1p8: vreg-s4a-1p8 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_s4a_1p8"; |
| |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| }; |
| |
| &adsp_pas { |
| status = "okay"; |
| firmware-name = "qcom/sdm845/adsp.mdt"; |
| }; |
| |
| &apps_rsc { |
| pm8998-rpmh-regulators { |
| compatible = "qcom,pm8998-rpmh-regulators"; |
| qcom,pmic-id = "a"; |
| |
| vreg_l1a_0p875: ldo1 { |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5a_0p8: ldo5 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7a_1p8: ldo7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12a_1p8: ldo12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13a_2p95: ldo13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14a_1p8: ldo14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vreg_l17a_1p3: ldo17 { |
| regulator-min-microvolt = <1304000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l20a_2p95: ldo20 { |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2968000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l21a_2p95: ldo21 { |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2968000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l24a_3p075: ldo24 { |
| regulator-min-microvolt = <3088000>; |
| regulator-max-microvolt = <3088000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l25a_3p3: ldo25 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3312000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l26a_1p2: ldo26 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-boot-on; |
| }; |
| }; |
| }; |
| |
| &cdsp_pas { |
| status = "okay"; |
| firmware-name = "qcom/sdm845/cdsp.mdt"; |
| }; |
| |
| &dsi0 { |
| status = "okay"; |
| vdda-supply = <&vreg_l26a_1p2>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| panel@0 { |
| compatible = "tianma,fhd-video"; |
| reg = <0>; |
| vddi0-supply = <&vreg_l14a_1p8>; |
| vddpos-supply = <&lab>; |
| vddneg-supply = <&ibb>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; |
| |
| port { |
| tianma_nt36672a_in_0: endpoint { |
| remote-endpoint = <&dsi0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &dsi0_out { |
| remote-endpoint = <&tianma_nt36672a_in_0>; |
| data-lanes = <0 1 2 3>; |
| }; |
| |
| &dsi0_phy { |
| status = "okay"; |
| vdds-supply = <&vreg_l1a_0p875>; |
| }; |
| |
| &gcc { |
| protected-clocks = <GCC_QSPI_CORE_CLK>, |
| <GCC_QSPI_CORE_CLK_SRC>, |
| <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, |
| <GCC_LPASS_Q6_AXI_CLK>, |
| <GCC_LPASS_SWAY_CLK>; |
| }; |
| |
| &gpu { |
| zap-shader { |
| memory-region = <&gpu_mem>; |
| firmware-name = "qcom/sdm845/a630_zap.mbn"; |
| }; |
| }; |
| |
| &ibb { |
| regulator-min-microvolt = <4600000>; |
| regulator-max-microvolt = <6000000>; |
| regulator-over-current-protection; |
| regulator-pull-down; |
| regulator-soft-start; |
| qcom,discharge-resistor-kohms = <300>; |
| }; |
| |
| &lab { |
| regulator-min-microvolt = <4600000>; |
| regulator-max-microvolt = <6000000>; |
| regulator-over-current-protection; |
| regulator-pull-down; |
| regulator-soft-start; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_mdp { |
| status = "okay"; |
| }; |
| |
| &mss_pil { |
| status = "okay"; |
| firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt"; |
| }; |
| |
| &pm8998_gpio { |
| vol_up_pin_a: vol-up-active { |
| pins = "gpio6"; |
| function = "normal"; |
| input-enable; |
| bias-pull-up; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| }; |
| }; |
| |
| &pm8998_pon { |
| resin { |
| compatible = "qcom,pm8941-resin"; |
| interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| linux,code = <KEY_VOLUMEDOWN>; |
| }; |
| }; |
| |
| /* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */ |
| &q6afedai { |
| qi2s@22 { |
| reg = <22>; |
| qcom,sd-lines = <0>; |
| }; |
| }; |
| |
| &q6asmdai { |
| dai@0 { |
| reg = <0>; |
| }; |
| |
| dai@1 { |
| reg = <1>; |
| }; |
| |
| dai@2 { |
| reg = <2>; |
| }; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| status = "okay"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>; |
| |
| vmmc-supply = <&vreg_l21a_2p95>; |
| vqmmc-supply = <&vreg_l13a_2p95>; |
| |
| bus-width = <4>; |
| cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| &sound { |
| compatible = "qcom,db845c-sndcard"; |
| pinctrl-0 = <&quat_mi2s_active |
| &quat_mi2s_sd0_active>; |
| pinctrl-names = "default"; |
| model = "Xiaomi Poco F1"; |
| audio-routing = |
| "RX_BIAS", "MCLK", |
| "AMIC1", "MIC BIAS1", |
| "AMIC2", "MIC BIAS2", |
| "AMIC3", "MIC BIAS3"; |
| |
| mm1-dai-link { |
| link-name = "MultiMedia1"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; |
| }; |
| }; |
| |
| mm2-dai-link { |
| link-name = "MultiMedia2"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; |
| }; |
| }; |
| |
| mm3-dai-link { |
| link-name = "MultiMedia3"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; |
| }; |
| }; |
| |
| slim-dai-link { |
| link-name = "SLIM Playback"; |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_0_RX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd9340 0>; |
| }; |
| }; |
| |
| slimcap-dai-link { |
| link-name = "SLIM Capture"; |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_0_TX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd9340 1>; |
| }; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <0 4>, <81 4>; |
| |
| sdc2_default_state: sdc2-default { |
| clk { |
| pins = "sdc2_clk"; |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| |
| cmd { |
| pins = "sdc2_cmd"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| data { |
| pins = "sdc2_data"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| }; |
| |
| sdc2_card_det_n: sd-card-det-n { |
| pins = "gpio126"; |
| function = "gpio"; |
| bias-pull-up; |
| }; |
| |
| wcd_intr_default: wcd_intr_default { |
| pins = <54>; |
| function = "gpio"; |
| |
| input-enable; |
| bias-pull-down; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| &uart6 { |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "qcom,wcn3990-bt"; |
| |
| vddio-supply = <&vreg_s4a_1p8>; |
| vddxo-supply = <&vreg_l7a_1p8>; |
| vddrf-supply = <&vreg_l17a_1p3>; |
| vddch0-supply = <&vreg_l25a_3p3>; |
| max-speed = <3200000>; |
| }; |
| }; |
| |
| &ufs_mem_hc { |
| status = "okay"; |
| |
| reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; |
| |
| vcc-supply = <&vreg_l20a_2p95>; |
| vcc-max-microamp = <800000>; |
| }; |
| |
| &ufs_mem_phy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l1a_0p875>; |
| vdda-pll-supply = <&vreg_l26a_1p2>; |
| }; |
| |
| &usb_1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| dr_mode = "peripheral"; |
| }; |
| |
| &usb_1_hsphy { |
| status = "okay"; |
| |
| vdd-supply = <&vreg_l1a_0p875>; |
| vdda-pll-supply = <&vreg_l12a_1p8>; |
| vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; |
| |
| qcom,imp-res-offset-value = <8>; |
| qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; |
| qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; |
| qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; |
| }; |
| |
| &usb_1_qmpphy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l26a_1p2>; |
| vdda-pll-supply = <&vreg_l1a_0p875>; |
| }; |
| |
| &wcd9340{ |
| pinctrl-0 = <&wcd_intr_default>; |
| pinctrl-names = "default"; |
| clock-names = "extclk"; |
| clocks = <&rpmhcc RPMH_LN_BB_CLK2>; |
| reset-gpios = <&tlmm 64 0>; |
| vdd-buck-supply = <&vreg_s4a_1p8>; |
| vdd-buck-sido-supply = <&vreg_s4a_1p8>; |
| vdd-tx-supply = <&vreg_s4a_1p8>; |
| vdd-rx-supply = <&vreg_s4a_1p8>; |
| vdd-io-supply = <&vreg_s4a_1p8>; |
| qcom,micbias1-microvolt = <2700000>; |
| qcom,micbias2-microvolt = <1800000>; |
| qcom,micbias3-microvolt = <2700000>; |
| qcom,micbias4-microvolt = <2700000>; |
| }; |
| |
| &wifi { |
| status = "okay"; |
| |
| vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; |
| vdd-1.8-xo-supply = <&vreg_l7a_1p8>; |
| vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; |
| vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; |
| }; |
| |
| /* PINCTRL - additions to nodes defined in sdm845.dtsi */ |
| |
| &qup_uart6_default { |
| pinmux { |
| pins = "gpio45", "gpio46", "gpio47", "gpio48"; |
| function = "qup6"; |
| }; |
| |
| cts { |
| pins = "gpio45"; |
| bias-disable; |
| }; |
| |
| rts-tx { |
| pins = "gpio46", "gpio47"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| rx { |
| pins = "gpio48"; |
| bias-pull-up; |
| }; |
| }; |
