| // SPDX-License-Identifier: GPL-2.0 |
| #include "qcom-msm8974.dtsi" |
| #include "qcom-pm8841.dtsi" |
| #include "qcom-pm8941.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| / { |
| model = "LGE MSM 8974 HAMMERHEAD"; |
| compatible = "lge,hammerhead", "qcom,msm8974"; |
| |
| aliases { |
| serial0 = &blsp1_uart1; |
| serial1 = &blsp2_uart10; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| smd { |
| rpm { |
| rpm_requests { |
| pm8841-regulators { |
| s1 { |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| s2 { |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| s3 { |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| s4 { |
| regulator-min-microvolt = <815000>; |
| regulator-max-microvolt = <900000>; |
| }; |
| }; |
| |
| pm8941-regulators { |
| vdd_l1_l3-supply = <&pm8941_s1>; |
| vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; |
| vdd_l4_l11-supply = <&pm8941_s1>; |
| vdd_l5_l7-supply = <&pm8941_s2>; |
| vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; |
| vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>; |
| vdd_l9_l10_l17_l22-supply = <&vreg_boost>; |
| vdd_l13_l20_l23_l24-supply = <&vreg_boost>; |
| vdd_l21-supply = <&vreg_boost>; |
| |
| s1 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| s2 { |
| regulator-min-microvolt = <2150000>; |
| regulator-max-microvolt = <2150000>; |
| |
| regulator-boot-on; |
| }; |
| |
| s3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| l3 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| l4 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| l5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| l11 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| l13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l15 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| l16 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| |
| l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| l18 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| l19 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| l20 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-boot-on; |
| regulator-system-load = <200000>; |
| regulator-allow-set-load; |
| }; |
| |
| l21 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l22 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| l23 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| l24 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| |
| regulator-boot-on; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| vreg_wlan: wlan-regulator { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "wl-reg"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&msmgpio 26 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_regulator_pin>; |
| }; |
| }; |
| |
| &soc { |
| serial@f991d000 { |
| status = "okay"; |
| }; |
| |
| pinctrl@fd510000 { |
| sdhc1_pin_a: sdhc1-pin-active { |
| clk { |
| pins = "sdc1_clk"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| cmd-data { |
| pins = "sdc1_cmd", "sdc1_data"; |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sdhc2_pin_a: sdhc2-pin-active { |
| clk { |
| pins = "sdc2_clk"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| cmd-data { |
| pins = "sdc2_cmd", "sdc2_data"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| }; |
| |
| i2c1_pins: i2c1 { |
| mux { |
| pins = "gpio2", "gpio3"; |
| function = "blsp_i2c1"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| i2c2_pins: i2c2 { |
| mux { |
| pins = "gpio6", "gpio7"; |
| function = "blsp_i2c2"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| i2c3_pins: i2c3 { |
| mux { |
| pins = "gpio10", "gpio11"; |
| function = "blsp_i2c3"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| i2c11_pins: i2c11 { |
| mux { |
| pins = "gpio83", "gpio84"; |
| function = "blsp_i2c11"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| i2c12_pins: i2c12 { |
| mux { |
| pins = "gpio87", "gpio88"; |
| function = "blsp_i2c12"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| mpu6515_pin: mpu6515 { |
| irq { |
| pins = "gpio73"; |
| function = "gpio"; |
| bias-disable; |
| input-enable; |
| }; |
| }; |
| |
| touch_pin: touch { |
| int { |
| pins = "gpio5"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| input-enable; |
| }; |
| |
| reset { |
| pins = "gpio8"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| panel_pin: panel { |
| te { |
| pins = "gpio12"; |
| function = "mdp_vsync"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| bt_pin: bt { |
| hostwake { |
| pins = "gpio42"; |
| function = "gpio"; |
| }; |
| |
| devwake { |
| pins = "gpio62"; |
| function = "gpio"; |
| }; |
| |
| shutdown { |
| pins = "gpio41"; |
| function = "gpio"; |
| }; |
| }; |
| |
| blsp2_uart10_pin_a: blsp2-uart10-pin-active { |
| tx { |
| pins = "gpio53"; |
| function = "blsp_uart10"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| rx { |
| pins = "gpio54"; |
| function = "blsp_uart10"; |
| |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| cts { |
| pins = "gpio55"; |
| function = "blsp_uart10"; |
| |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| rts { |
| pins = "gpio56"; |
| function = "blsp_uart10"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| }; |
| |
| sdhci@f9824900 { |
| status = "okay"; |
| |
| vmmc-supply = <&pm8941_l20>; |
| vqmmc-supply = <&pm8941_s3>; |
| |
| bus-width = <8>; |
| non-removable; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhc1_pin_a>; |
| }; |
| |
| sdhci@f98a4900 { |
| status = "okay"; |
| |
| max-frequency = <100000000>; |
| bus-width = <4>; |
| non-removable; |
| vmmc-supply = <&vreg_wlan>; |
| vqmmc-supply = <&pm8941_s3>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhc2_pin_a>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bcrmf@1 { |
| compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac"; |
| reg = <1>; |
| |
| brcm,drive-strength = <10>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_sleep_clk_pin>; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys_pin_a>; |
| |
| volume-up { |
| label = "volume_up"; |
| gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEUP>; |
| }; |
| |
| volume-down { |
| label = "volume_down"; |
| gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| }; |
| }; |
| |
| serial@f9960000 { |
| status = "okay"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&blsp2_uart10_pin_a>; |
| |
| bluetooth { |
| compatible = "brcm,bcm43438-bt"; |
| max-speed = <3000000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&bt_pin>; |
| |
| host-wakeup-gpios = <&msmgpio 42 GPIO_ACTIVE_HIGH>; |
| device-wakeup-gpios = <&msmgpio 62 GPIO_ACTIVE_HIGH>; |
| shutdown-gpios = <&msmgpio 41 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| i2c@f9967000 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c11_pins>; |
| clock-frequency = <355000>; |
| qcom,src-freq = <50000000>; |
| |
| led-controller@38 { |
| compatible = "ti,lm3630a"; |
| status = "okay"; |
| reg = <0x38>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@0 { |
| reg = <0>; |
| led-sources = <0 1>; |
| label = "lcd-backlight"; |
| default-brightness = <200>; |
| }; |
| }; |
| }; |
| |
| i2c@f9968000 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c12_pins>; |
| clock-frequency = <100000>; |
| qcom,src-freq = <50000000>; |
| |
| mpu6515@68 { |
| compatible = "invensense,mpu6515"; |
| reg = <0x68>; |
| interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>; |
| vddio-supply = <&pm8941_lvs1>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mpu6515_pin>; |
| |
| mount-matrix = "0", "-1", "0", |
| "-1", "0", "0", |
| "0", "0", "1"; |
| |
| i2c-gate { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ak8963@f { |
| compatible = "asahi-kasei,ak8963"; |
| reg = <0x0f>; |
| gpios = <&msmgpio 67 0>; |
| vid-supply = <&pm8941_lvs1>; |
| vdd-supply = <&pm8941_l17>; |
| }; |
| |
| bmp280@76 { |
| compatible = "bosch,bmp280"; |
| reg = <0x76>; |
| vdda-supply = <&pm8941_lvs1>; |
| vddd-supply = <&pm8941_l17>; |
| }; |
| }; |
| }; |
| }; |
| |
| i2c@f9923000 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_pins>; |
| clock-frequency = <100000>; |
| qcom,src-freq = <50000000>; |
| |
| charger: bq24192@6b { |
| compatible = "ti,bq24192"; |
| reg = <0x6b>; |
| interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>; |
| |
| omit-battery-class; |
| |
| usb_otg_vbus: usb-otg-vbus { }; |
| }; |
| |
| fuelgauge: max17048@36 { |
| compatible = "maxim,max17048"; |
| reg = <0x36>; |
| |
| maxim,double-soc; |
| maxim,rcomp = /bits/ 8 <0x4d>; |
| |
| interrupt-parent = <&msmgpio>; |
| interrupts = <9 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&fuelgauge_pin>; |
| |
| maxim,alert-low-soc-level = <2>; |
| }; |
| }; |
| |
| i2c@f9924000 { |
| status = "okay"; |
| |
| clock-frequency = <355000>; |
| qcom,src-freq = <50000000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c2_pins>; |
| |
| synaptics@70 { |
| compatible = "syna,rmi4-i2c"; |
| reg = <0x70>; |
| |
| interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>; |
| vdd-supply = <&pm8941_l22>; |
| vio-supply = <&pm8941_lvs3>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&touch_pin>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| rmi4-f01@1 { |
| reg = <0x1>; |
| syna,nosleep-mode = <1>; |
| }; |
| |
| rmi4-f12@12 { |
| reg = <0x12>; |
| syna,sensor-type = <1>; |
| }; |
| }; |
| }; |
| |
| i2c@f9925000 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c3_pins>; |
| clock-frequency = <100000>; |
| qcom,src-freq = <50000000>; |
| |
| avago_apds993@39 { |
| compatible = "avago,apds9930"; |
| reg = <0x39>; |
| interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>; |
| vdd-supply = <&pm8941_l17>; |
| vddio-supply = <&pm8941_lvs1>; |
| led-max-microamp = <100000>; |
| amstaos,proximity-diodes = <0>; |
| }; |
| }; |
| |
| usb@f9a55000 { |
| status = "okay"; |
| |
| phys = <&usb_hs1_phy>; |
| phy-select = <&tcsr 0xb000 0>; |
| |
| extcon = <&charger>, <&usb_id>; |
| vbus-supply = <&usb_otg_vbus>; |
| |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| |
| ulpi { |
| phy@a { |
| status = "okay"; |
| |
| v1p8-supply = <&pm8941_l6>; |
| v3p3-supply = <&pm8941_l24>; |
| |
| qcom,init-seq = /bits/ 8 <0x1 0x64>; |
| }; |
| }; |
| }; |
| |
| mdss@fd900000 { |
| status = "okay"; |
| |
| mdp@fd900000 { |
| status = "okay"; |
| }; |
| |
| dsi@fd922800 { |
| status = "okay"; |
| |
| vdda-supply = <&pm8941_l2>; |
| vdd-supply = <&pm8941_lvs3>; |
| vddio-supply = <&pm8941_l12>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ports { |
| port@1 { |
| endpoint { |
| remote-endpoint = <&panel_in>; |
| data-lanes = <0 1 2 3>; |
| }; |
| }; |
| }; |
| |
| panel: panel@0 { |
| reg = <0>; |
| compatible = "lg,acx467akm-7"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&panel_pin>; |
| |
| port { |
| panel_in: endpoint { |
| remote-endpoint = <&dsi0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| dsi-phy@fd922a00 { |
| status = "okay"; |
| |
| vddio-supply = <&pm8941_l12>; |
| }; |
| }; |
| }; |
| |
| &spmi_bus { |
| pm8941@0 { |
| gpios@c000 { |
| gpio_keys_pin_a: gpio-keys-active { |
| pins = "gpio2", "gpio3"; |
| function = "normal"; |
| |
| bias-pull-up; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| fuelgauge_pin: fuelgauge-int { |
| pins = "gpio9"; |
| function = "normal"; |
| |
| bias-disable; |
| input-enable; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| wlan_sleep_clk_pin: wl-sleep-clk { |
| pins = "gpio16"; |
| function = "func2"; |
| |
| output-high; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| wlan_regulator_pin: wl-reg-active { |
| pins = "gpio17"; |
| function = "normal"; |
| |
| bias-disable; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| otg { |
| gpio-hog; |
| gpios = <35 GPIO_ACTIVE_HIGH>; |
| output-high; |
| line-name = "otg-gpio"; |
| }; |
| }; |
| }; |
| }; |
