| // SPDX-License-Identifier: GPL-2.0 |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/spmi/spmi.h> |
| |
| &spmi_bus { |
| |
| pm8916_0: pm8916@0 { |
| compatible = "qcom,pm8916", "qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| rtc@6000 { |
| compatible = "qcom,pm8941-rtc"; |
| reg = <0x6000>; |
| reg-names = "rtc", "alarm"; |
| interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; |
| }; |
| |
| pon@800 { |
| compatible = "qcom,pm8916-pon"; |
| reg = <0x800>; |
| mode-bootloader = <0x2>; |
| mode-recovery = <0x1>; |
| |
| pwrkey { |
| compatible = "qcom,pm8941-pwrkey"; |
| interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| linux,code = <KEY_POWER>; |
| }; |
| |
| watchdog { |
| compatible = "qcom,pm8916-wdt"; |
| interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>; |
| timeout-sec = <60>; |
| }; |
| }; |
| |
| pm8916_gpios: gpios@c000 { |
| compatible = "qcom,pm8916-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts = <0 0xc0 0 IRQ_TYPE_NONE>, |
| <0 0xc1 0 IRQ_TYPE_NONE>, |
| <0 0xc2 0 IRQ_TYPE_NONE>, |
| <0 0xc3 0 IRQ_TYPE_NONE>; |
| }; |
| |
| pm8916_mpps: mpps@a000 { |
| compatible = "qcom,pm8916-mpp"; |
| reg = <0xa000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts = <0 0xa0 0 IRQ_TYPE_NONE>, |
| <0 0xa1 0 IRQ_TYPE_NONE>, |
| <0 0xa2 0 IRQ_TYPE_NONE>, |
| <0 0xa3 0 IRQ_TYPE_NONE>; |
| }; |
| |
| pm8916_temp: temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400>; |
| interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; |
| io-channels = <&pm8916_vadc VADC_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8916_vadc: vadc@3100 { |
| compatible = "qcom,spmi-vadc"; |
| reg = <0x3100>; |
| interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| usb_in { |
| reg = <VADC_USBIN>; |
| qcom,pre-scaling = <1 10>; |
| }; |
| vph_pwr { |
| reg = <VADC_VSYS>; |
| qcom,pre-scaling = <1 3>; |
| }; |
| die_temp { |
| reg = <VADC_DIE_TEMP>; |
| }; |
| ref_625mv { |
| reg = <VADC_REF_625MV>; |
| }; |
| ref_1250v { |
| reg = <VADC_REF_1250MV>; |
| }; |
| ref_gnd { |
| reg = <VADC_GND_REF>; |
| }; |
| ref_vdd { |
| reg = <VADC_VDD_VADC>; |
| }; |
| }; |
| }; |
| |
| pm8916_1: pm8916@1 { |
| compatible = "qcom,pm8916", "qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8916_vib: vibrator@c000 { |
| compatible = "qcom,pm8916-vib"; |
| reg = <0xc000>; |
| status = "disabled"; |
| }; |
| |
| wcd_codec: codec@f000 { |
| compatible = "qcom,pm8916-wcd-analog-codec"; |
| reg = <0xf000 0x200>; |
| reg-names = "pmic-codec-core"; |
| clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>; |
| clock-names = "mclk"; |
| interrupt-parent = <&spmi_bus>; |
| interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x1 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x2 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x3 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x4 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x5 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x6 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x7 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x0 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x1 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x2 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x3 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x4 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x5 IRQ_TYPE_NONE>; |
| interrupt-names = "cdc_spk_cnp_int", |
| "cdc_spk_clip_int", |
| "cdc_spk_ocp_int", |
| "mbhc_ins_rem_det1", |
| "mbhc_but_rel_det", |
| "mbhc_but_press_det", |
| "mbhc_ins_rem_det", |
| "mbhc_switch_int", |
| "cdc_ear_ocp_int", |
| "cdc_hphr_ocp_int", |
| "cdc_hphl_ocp_det", |
| "cdc_ear_cnp_int", |
| "cdc_hphr_cnp_int", |
| "cdc_hphl_cnp_int"; |
| vdd-cdc-io-supply = <&pm8916_l5>; |
| vdd-cdc-tx-rx-cx-supply = <&pm8916_l5>; |
| vdd-micbias-supply = <&pm8916_l13>; |
| #sound-dai-cells = <1>; |
| }; |
| }; |
| }; |
