| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * SPI bus driver for the Topcliff PCH used by Intel SoCs |
| * |
| * Copyright (C) 2011 LAPIS Semiconductor Co., Ltd. |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/pci.h> |
| #include <linux/wait.h> |
| #include <linux/spi/spi.h> |
| #include <linux/interrupt.h> |
| #include <linux/sched.h> |
| #include <linux/spi/spidev.h> |
| #include <linux/module.h> |
| #include <linux/device.h> |
| #include <linux/platform_device.h> |
| |
| #include <linux/dmaengine.h> |
| #include <linux/pch_dma.h> |
| |
| /* Register offsets */ |
| #define PCH_SPCR 0x00 /* SPI control register */ |
| #define PCH_SPBRR 0x04 /* SPI baud rate register */ |
| #define PCH_SPSR 0x08 /* SPI status register */ |
| #define PCH_SPDWR 0x0C /* SPI write data register */ |
| #define PCH_SPDRR 0x10 /* SPI read data register */ |
| #define PCH_SSNXCR 0x18 /* SSN Expand Control Register */ |
| #define PCH_SRST 0x1C /* SPI reset register */ |
| #define PCH_ADDRESS_SIZE 0x20 |
| |
| #define PCH_SPSR_TFD 0x000007C0 |
| #define PCH_SPSR_RFD 0x0000F800 |
| |
| #define PCH_READABLE(x) (((x) & PCH_SPSR_RFD)>>11) |
| #define PCH_WRITABLE(x) (((x) & PCH_SPSR_TFD)>>6) |
| |
| #define PCH_RX_THOLD 7 |
| #define PCH_RX_THOLD_MAX 15 |
| |
| #define PCH_TX_THOLD 2 |
| |
| #define PCH_MAX_BAUDRATE 5000000 |
| #define PCH_MAX_FIFO_DEPTH 16 |
| |
| #define STATUS_RUNNING 1 |
| #define STATUS_EXITING 2 |
| #define PCH_SLEEP_TIME 10 |
| |
| #define SSN_LOW 0x02U |
| #define SSN_HIGH 0x03U |
| #define SSN_NO_CONTROL 0x00U |
| #define PCH_MAX_CS 0xFF |
| #define PCI_DEVICE_ID_GE_SPI 0x8816 |
| |
| #define SPCR_SPE_BIT (1 << 0) |
| #define SPCR_MSTR_BIT (1 << 1) |
| #define SPCR_LSBF_BIT (1 << 4) |
| #define SPCR_CPHA_BIT (1 << 5) |
| #define SPCR_CPOL_BIT (1 << 6) |
| #define SPCR_TFIE_BIT (1 << 8) |
| #define SPCR_RFIE_BIT (1 << 9) |
| #define SPCR_FIE_BIT (1 << 10) |
| #define SPCR_ORIE_BIT (1 << 11) |
| #define SPCR_MDFIE_BIT (1 << 12) |
| #define SPCR_FICLR_BIT (1 << 24) |
| #define SPSR_TFI_BIT (1 << 0) |
| #define SPSR_RFI_BIT (1 << 1) |
| #define SPSR_FI_BIT (1 << 2) |
| #define SPSR_ORF_BIT (1 << 3) |
| #define SPBRR_SIZE_BIT (1 << 10) |
| |
| #define PCH_ALL (SPCR_TFIE_BIT|SPCR_RFIE_BIT|SPCR_FIE_BIT|\ |
| SPCR_ORIE_BIT|SPCR_MDFIE_BIT) |
| |
| #define SPCR_RFIC_FIELD 20 |
| #define SPCR_TFIC_FIELD 16 |
| |
| #define MASK_SPBRR_SPBR_BITS ((1 << 10) - 1) |
| #define MASK_RFIC_SPCR_BITS (0xf << SPCR_RFIC_FIELD) |
| #define MASK_TFIC_SPCR_BITS (0xf << SPCR_TFIC_FIELD) |
| |
| #define PCH_CLOCK_HZ 50000000 |
| #define PCH_MAX_SPBR 1023 |
| |
| /* Definition for ML7213/ML7223/ML7831 by LAPIS Semiconductor */ |
| #define PCI_DEVICE_ID_ML7213_SPI 0x802c |
| #define PCI_DEVICE_ID_ML7223_SPI 0x800F |
| #define PCI_DEVICE_ID_ML7831_SPI 0x8816 |
| |
| /* |
| * Set the number of SPI instance max |
| * Intel EG20T PCH : 1ch |
| * LAPIS Semiconductor ML7213 IOH : 2ch |
| * LAPIS Semiconductor ML7223 IOH : 1ch |
| * LAPIS Semiconductor ML7831 IOH : 1ch |
| */ |
| #define PCH_SPI_MAX_DEV 2 |
| |
| #define PCH_BUF_SIZE 4096 |
| #define PCH_DMA_TRANS_SIZE 12 |
| |
| static int use_dma = 1; |
| |
| struct pch_spi_dma_ctrl { |
| struct dma_async_tx_descriptor *desc_tx; |
| struct dma_async_tx_descriptor *desc_rx; |
| struct pch_dma_slave param_tx; |
| struct pch_dma_slave param_rx; |
| struct dma_chan *chan_tx; |
| struct dma_chan *chan_rx; |
| struct scatterlist *sg_tx_p; |
| struct scatterlist *sg_rx_p; |
| struct scatterlist sg_tx; |
| struct scatterlist sg_rx; |
| int nent; |
| void *tx_buf_virt; |
| void *rx_buf_virt; |
| dma_addr_t tx_buf_dma; |
| dma_addr_t rx_buf_dma; |
| }; |
| /** |
| * struct pch_spi_data - Holds the SPI channel specific details |
| * @io_remap_addr: The remapped PCI base address |
| * @master: Pointer to the SPI master structure |
| * @work: Reference to work queue handler |
| * @wait: Wait queue for waking up upon receiving an |
| * interrupt. |
| * @transfer_complete: Status of SPI Transfer |
| * @bcurrent_msg_processing: Status flag for message processing |
| * @lock: Lock for protecting this structure |
| * @queue: SPI Message queue |
| * @status: Status of the SPI driver |
| * @bpw_len: Length of data to be transferred in bits per |
| * word |
| * @transfer_active: Flag showing active transfer |
| * @tx_index: Transmit data count; for bookkeeping during |
| * transfer |
| * @rx_index: Receive data count; for bookkeeping during |
| * transfer |
| * @tx_buff: Buffer for data to be transmitted |
| * @rx_index: Buffer for Received data |
| * @n_curnt_chip: The chip number that this SPI driver currently |
| * operates on |
| * @current_chip: Reference to the current chip that this SPI |
| * driver currently operates on |
| * @current_msg: The current message that this SPI driver is |
| * handling |
| * @cur_trans: The current transfer that this SPI driver is |
| * handling |
| * @board_dat: Reference to the SPI device data structure |
| * @plat_dev: platform_device structure |
| * @ch: SPI channel number |
| * @irq_reg_sts: Status of IRQ registration |
| */ |
| struct pch_spi_data { |
| void __iomem *io_remap_addr; |
| unsigned long io_base_addr; |
| struct spi_master *master; |
| struct work_struct work; |
| wait_queue_head_t wait; |
| u8 transfer_complete; |
| u8 bcurrent_msg_processing; |
| spinlock_t lock; |
| struct list_head queue; |
| u8 status; |
| u32 bpw_len; |
| u8 transfer_active; |
| u32 tx_index; |
| u32 rx_index; |
| u16 *pkt_tx_buff; |
| u16 *pkt_rx_buff; |
| u8 n_curnt_chip; |
| struct spi_device *current_chip; |
| struct spi_message *current_msg; |
| struct spi_transfer *cur_trans; |
| struct pch_spi_board_data *board_dat; |
| struct platform_device *plat_dev; |
| int ch; |
| struct pch_spi_dma_ctrl dma; |
| int use_dma; |
| u8 irq_reg_sts; |
| int save_total_len; |
| }; |
| |
| /** |
| * struct pch_spi_board_data - Holds the SPI device specific details |
| * @pdev: Pointer to the PCI device |
| * @suspend_sts: Status of suspend |
| * @num: The number of SPI device instance |
| */ |
| struct pch_spi_board_data { |
| struct pci_dev *pdev; |
| u8 suspend_sts; |
| int num; |
| }; |
| |
| struct pch_pd_dev_save { |
| int num; |
| struct platform_device *pd_save[PCH_SPI_MAX_DEV]; |
| struct pch_spi_board_data *board_dat; |
| }; |
| |
| static const struct pci_device_id pch_spi_pcidev_id[] = { |
| { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_GE_SPI), 1, }, |
| { PCI_VDEVICE(ROHM, PCI_DEVICE_ID_ML7213_SPI), 2, }, |
| { PCI_VDEVICE(ROHM, PCI_DEVICE_ID_ML7223_SPI), 1, }, |
| { PCI_VDEVICE(ROHM, PCI_DEVICE_ID_ML7831_SPI), 1, }, |
| { } |
| }; |
| |
| /** |
| * pch_spi_writereg() - Performs register writes |
| * @master: Pointer to struct spi_master. |
| * @idx: Register offset. |
| * @val: Value to be written to register. |
| */ |
| static inline void pch_spi_writereg(struct spi_master *master, int idx, u32 val) |
| { |
| struct pch_spi_data *data = spi_master_get_devdata(master); |
| iowrite32(val, (data->io_remap_addr + idx)); |
| } |
| |
| /** |
| * pch_spi_readreg() - Performs register reads |
| * @master: Pointer to struct spi_master. |
| * @idx: Register offset. |
| */ |
| static inline u32 pch_spi_readreg(struct spi_master *master, int idx) |
| { |
| struct pch_spi_data *data = spi_master_get_devdata(master); |
| return ioread32(data->io_remap_addr + idx); |
| } |
| |
| static inline void pch_spi_setclr_reg(struct spi_master *master, int idx, |
| u32 set, u32 clr) |
| { |
| u32 tmp = pch_spi_readreg(master, idx); |
| tmp = (tmp & ~clr) | set; |
| pch_spi_writereg(master, idx, tmp); |
| } |
| |
| static void pch_spi_set_master_mode(struct spi_master *master) |
| { |
| pch_spi_setclr_reg(master, PCH_SPCR, SPCR_MSTR_BIT, 0); |
| } |
| |
| /** |
| * pch_spi_clear_fifo() - Clears the Transmit and Receive FIFOs |
| * @master: Pointer to struct spi_master. |
| */ |
| static void pch_spi_clear_fifo(struct spi_master *master) |
| { |
| pch_spi_setclr_reg(master, PCH_SPCR, SPCR_FICLR_BIT, 0); |
| pch_spi_setclr_reg(master, PCH_SPCR, 0, SPCR_FICLR_BIT); |
| } |
| |
| static void pch_spi_handler_sub(struct pch_spi_data *data, u32 reg_spsr_val, |
| void __iomem *io_remap_addr) |
| { |
| u32 n_read, tx_index, rx_index, bpw_len; |
| u16 *pkt_rx_buffer, *pkt_tx_buff; |
| int read_cnt; |
| u32 reg_spcr_val; |
| void __iomem *spsr; |
| void __iomem *spdrr; |
| void __iomem *spdwr; |
| |
| spsr = io_remap_addr + PCH_SPSR; |
| iowrite32(reg_spsr_val, spsr); |
| |
| if (data->transfer_active) { |
| rx_index = data->rx_index; |
| tx_index = data->tx_index; |
| bpw_len = data->bpw_len; |
| pkt_rx_buffer = data->pkt_rx_buff; |
| pkt_tx_buff = data->pkt_tx_buff; |
| |
| spdrr = io_remap_addr + PCH_SPDRR; |
| spdwr = io_remap_addr + PCH_SPDWR; |
| |
| n_read = PCH_READABLE(reg_spsr_val); |
| |
| for (read_cnt = 0; (read_cnt < n_read); read_cnt++) { |
| pkt_rx_buffer[rx_index++] = ioread32(spdrr); |
| if (tx_index < bpw_len) |
| iowrite32(pkt_tx_buff[tx_index++], spdwr); |
| } |
| |
| /* disable RFI if not needed */ |
| if ((bpw_len - rx_index) <= PCH_MAX_FIFO_DEPTH) { |
| reg_spcr_val = ioread32(io_remap_addr + PCH_SPCR); |
| reg_spcr_val &= ~SPCR_RFIE_BIT; /* disable RFI */ |
| |
| /* reset rx threshold */ |
| reg_spcr_val &= ~MASK_RFIC_SPCR_BITS; |
| reg_spcr_val |= (PCH_RX_THOLD_MAX << SPCR_RFIC_FIELD); |
| |
| iowrite32(reg_spcr_val, (io_remap_addr + PCH_SPCR)); |
| } |
| |
| /* update counts */ |
| data->tx_index = tx_index; |
| data->rx_index = rx_index; |
| |
| /* if transfer complete interrupt */ |
| if (reg_spsr_val & SPSR_FI_BIT) { |
| if ((tx_index == bpw_len) && (rx_index == tx_index)) { |
| /* disable interrupts */ |
| pch_spi_setclr_reg(data->master, PCH_SPCR, 0, |
| PCH_ALL); |
| |
| /* transfer is completed; |
| inform pch_spi_process_messages */ |
| data->transfer_complete = true; |
| data->transfer_active = false; |
| wake_up(&data->wait); |
| } else { |
| dev_vdbg(&data->master->dev, |
| "%s : Transfer is not completed", |
| __func__); |
| } |
| } |
| } |
| } |
| |
| /** |
| * pch_spi_handler() - Interrupt handler |
| * @irq: The interrupt number. |
| * @dev_id: Pointer to struct pch_spi_board_data. |
| */ |
| static irqreturn_t pch_spi_handler(int irq, void *dev_id) |
| { |
| u32 reg_spsr_val; |
| void __iomem *spsr; |
| void __iomem *io_remap_addr; |
| irqreturn_t ret = IRQ_NONE; |
| struct pch_spi_data *data = dev_id; |
| struct pch_spi_board_data *board_dat = data->board_dat; |
| |
| if (board_dat->suspend_sts) { |
| dev_dbg(&board_dat->pdev->dev, |
| "%s returning due to suspend\n", __func__); |
| return IRQ_NONE; |
| } |
| |
| io_remap_addr = data->io_remap_addr; |
| spsr = io_remap_addr + PCH_SPSR; |
| |
| reg_spsr_val = ioread32(spsr); |
| |
| if (reg_spsr_val & SPSR_ORF_BIT) { |
| dev_err(&board_dat->pdev->dev, "%s Over run error\n", __func__); |
| if (data->current_msg->complete) { |
| data->transfer_complete = true; |
| data->current_msg->status = -EIO; |
| data->current_msg->complete(data->current_msg->context); |
| data->bcurrent_msg_processing = false; |
| data->current_msg = NULL; |
| data->cur_trans = NULL; |
| } |
| } |
| |
| if (data->use_dma) |
| return IRQ_NONE; |
| |
| /* Check if the interrupt is for SPI device */ |
| if (reg_spsr_val & (SPSR_FI_BIT | SPSR_RFI_BIT)) { |
| pch_spi_handler_sub(data, reg_spsr_val, io_remap_addr); |
| ret = IRQ_HANDLED; |
| } |
| |
| dev_dbg(&board_dat->pdev->dev, "%s EXIT return value=%d\n", |
| __func__, ret); |
| |
| return ret; |
| } |
| |
| /** |
| * pch_spi_set_baud_rate() - Sets SPBR field in SPBRR |
| * @master: Pointer to struct spi_master. |
| * @speed_hz: Baud rate. |
| */ |
| static void pch_spi_set_baud_rate(struct spi_master *master, u32 speed_hz) |
| { |
| u32 n_spbr = PCH_CLOCK_HZ / (speed_hz * 2); |
| |
| /* if baud rate is less than we can support limit it */ |
| if (n_spbr > PCH_MAX_SPBR) |
| n_spbr = PCH_MAX_SPBR; |
| |
| pch_spi_setclr_reg(master, PCH_SPBRR, n_spbr, MASK_SPBRR_SPBR_BITS); |
| } |
| |
| /** |
| * pch_spi_set_bits_per_word() - Sets SIZE field in SPBRR |
| * @master: Pointer to struct spi_master. |
| * @bits_per_word: Bits per word for SPI transfer. |
| */ |
| static void pch_spi_set_bits_per_word(struct spi_master *master, |
| u8 bits_per_word) |
| { |
| if (bits_per_word == 8) |
| pch_spi_setclr_reg(master, PCH_SPBRR, 0, SPBRR_SIZE_BIT); |
| else |
| pch_spi_setclr_reg(master, PCH_SPBRR, SPBRR_SIZE_BIT, 0); |
| } |
| |
| /** |
| * pch_spi_setup_transfer() - Configures the PCH SPI hardware for transfer |
| * @spi: Pointer to struct spi_device. |
| */ |
| static void pch_spi_setup_transfer(struct spi_device *spi) |
| { |
| u32 flags = 0; |
| |
| dev_dbg(&spi->dev, "%s SPBRR content =%x setting baud rate=%d\n", |
| __func__, pch_spi_readreg(spi->master, PCH_SPBRR), |
| spi->max_speed_hz); |
| pch_spi_set_baud_rate(spi->master, spi->max_speed_hz); |
| |
| /* set bits per word */ |
| pch_spi_set_bits_per_word(spi->master, spi->bits_per_word); |
| |
| if (!(spi->mode & SPI_LSB_FIRST)) |
| flags |= SPCR_LSBF_BIT; |
| if (spi->mode & SPI_CPOL) |
| flags |= SPCR_CPOL_BIT; |
| if (spi->mode & SPI_CPHA) |
| flags |= SPCR_CPHA_BIT; |
| pch_spi_setclr_reg(spi->master, PCH_SPCR, flags, |
| (SPCR_LSBF_BIT | SPCR_CPOL_BIT | SPCR_CPHA_BIT)); |
| |
| /* Clear the FIFO by toggling FICLR to 1 and back to 0 */ |
| pch_spi_clear_fifo(spi->master); |
| } |
| |
| /** |
| * pch_spi_reset() - Clears SPI registers |
| * @master: Pointer to struct spi_master. |
| */ |
| static void pch_spi_reset(struct spi_master *master) |
| { |
| /* write 1 to reset SPI */ |
| pch_spi_writereg(master, PCH_SRST, 0x1); |
| |
| /* clear reset */ |
| pch_spi_writereg(master, PCH_SRST, 0x0); |
| } |
| |
| static int pch_spi_transfer(struct spi_device *pspi, struct spi_message *pmsg) |
| { |
| |
| struct spi_transfer *transfer; |
| struct pch_spi_data *data = spi_master_get_devdata(pspi->master); |
| int retval; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&data->lock, flags); |
| /* validate Tx/Rx buffers and Transfer length */ |
| list_for_each_entry(transfer, &pmsg->transfers, transfer_list) { |
| if (!transfer->tx_buf && !transfer->rx_buf) { |
| dev_err(&pspi->dev, |
| "%s Tx and Rx buffer NULL\n", __func__); |
| retval = -EINVAL; |
| goto err_return_spinlock; |
| } |
| |
| if (!transfer->len) { |
| dev_err(&pspi->dev, "%s Transfer length invalid\n", |
| __func__); |
| retval = -EINVAL; |
| goto err_return_spinlock; |
| } |
| |
| dev_dbg(&pspi->dev, |
| "%s Tx/Rx buffer valid. Transfer length valid\n", |
| __func__); |
| } |
| spin_unlock_irqrestore(&data->lock, flags); |
| |
| /* We won't process any messages if we have been asked to terminate */ |
| if (data->status == STATUS_EXITING) { |
| dev_err(&pspi->dev, "%s status = STATUS_EXITING.\n", __func__); |
| retval = -ESHUTDOWN; |
| goto err_out; |
| } |
| |
| /* If suspended ,return -EINVAL */ |
| if (data->board_dat->suspend_sts) { |
| dev_err(&pspi->dev, "%s suspend; returning EINVAL\n", __func__); |
| retval = -EINVAL; |
| goto err_out; |
| } |
| |
| /* set status of message */ |
| pmsg->actual_length = 0; |
| dev_dbg(&pspi->dev, "%s - pmsg->status =%d\n", __func__, pmsg->status); |
| |
| pmsg->status = -EINPROGRESS; |
| spin_lock_irqsave(&data->lock, flags); |
| /* add message to queue */ |
| list_add_tail(&pmsg->queue, &data->queue); |
| spin_unlock_irqrestore(&data->lock, flags); |
| |
| dev_dbg(&pspi->dev, "%s - Invoked list_add_tail\n", __func__); |
| |
| schedule_work(&data->work); |
| dev_dbg(&pspi->dev, "%s - Invoked queue work\n", __func__); |
| |
| retval = 0; |
| |
| err_out: |
| dev_dbg(&pspi->dev, "%s RETURN=%d\n", __func__, retval); |
| return retval; |
| err_return_spinlock: |
| dev_dbg(&pspi->dev, "%s RETURN=%d\n", __func__, retval); |
| spin_unlock_irqrestore(&data->lock, flags); |
| return retval; |
| } |
| |
| static inline void pch_spi_select_chip(struct pch_spi_data *data, |
| struct spi_device *pspi) |
| { |
| if (data->current_chip != NULL) { |
| if (pspi->chip_select != data->n_curnt_chip) { |
| dev_dbg(&pspi->dev, "%s : different slave\n", __func__); |
| data->current_chip = NULL; |
| } |
| } |
| |
| data->current_chip = pspi; |
| |
| data->n_curnt_chip = data->current_chip->chip_select; |
| |
| dev_dbg(&pspi->dev, "%s :Invoking pch_spi_setup_transfer\n", __func__); |
| pch_spi_setup_transfer(pspi); |
| } |
| |
| static void pch_spi_set_tx(struct pch_spi_data *data, int *bpw) |
| { |
| int size; |
| u32 n_writes; |
| int j; |
| struct spi_message *pmsg, *tmp; |
| const u8 *tx_buf; |
| const u16 *tx_sbuf; |
| |
| /* set baud rate if needed */ |
| if (data->cur_trans->speed_hz) { |
| dev_dbg(&data->master->dev, "%s:setting baud rate\n", __func__); |
| pch_spi_set_baud_rate(data->master, data->cur_trans->speed_hz); |
| } |
| |
| /* set bits per word if needed */ |
| if (data->cur_trans->bits_per_word && |
| (data->current_msg->spi->bits_per_word != data->cur_trans->bits_per_word)) { |
| dev_dbg(&data->master->dev, "%s:set bits per word\n", __func__); |
| pch_spi_set_bits_per_word(data->master, |
| data->cur_trans->bits_per_word); |
| *bpw = data->cur_trans->bits_per_word; |
| } else { |
| *bpw = data->current_msg->spi->bits_per_word; |
| } |
| |
| /* reset Tx/Rx index */ |
| data->tx_index = 0; |
| data->rx_index = 0; |
| |
| data->bpw_len = data->cur_trans->len / (*bpw / 8); |
| |
| /* find alloc size */ |
| size = data->cur_trans->len * sizeof(*data->pkt_tx_buff); |
| |
| /* allocate memory for pkt_tx_buff & pkt_rx_buffer */ |
| data->pkt_tx_buff = kzalloc(size, GFP_KERNEL); |
| if (data->pkt_tx_buff != NULL) { |
| data->pkt_rx_buff = kzalloc(size, GFP_KERNEL); |
| if (!data->pkt_rx_buff) |
| kfree(data->pkt_tx_buff); |
| } |
| |
| if (!data->pkt_rx_buff) { |
| /* flush queue and set status of all transfers to -ENOMEM */ |
| list_for_each_entry_safe(pmsg, tmp, data->queue.next, queue) { |
| pmsg->status = -ENOMEM; |
| |
| if (pmsg->complete) |
| pmsg->complete(pmsg->context); |
| |
| /* delete from queue */ |
| list_del_init(&pmsg->queue); |
| } |
| return; |
| } |
| |
| /* copy Tx Data */ |
| if (data->cur_trans->tx_buf != NULL) { |
| if (*bpw == 8) { |
| tx_buf = data->cur_trans->tx_buf; |
| for (j = 0; j < data->bpw_len; j++) |
| data->pkt_tx_buff[j] = *tx_buf++; |
| } else { |
| tx_sbuf = data->cur_trans->tx_buf; |
| for (j = 0; j < data->bpw_len; j++) |
| data->pkt_tx_buff[j] = *tx_sbuf++; |
| } |
| } |
| |
| /* if len greater than PCH_MAX_FIFO_DEPTH, write 16,else len bytes */ |
| n_writes = data->bpw_len; |
| if (n_writes > PCH_MAX_FIFO_DEPTH) |
| n_writes = PCH_MAX_FIFO_DEPTH; |
| |
| dev_dbg(&data->master->dev, |
| "\n%s:Pulling down SSN low - writing 0x2 to SSNXCR\n", |
| __func__); |
| pch_spi_writereg(data->master, PCH_SSNXCR, SSN_LOW); |
| |
| for (j = 0; j < n_writes; j++) |
| pch_spi_writereg(data->master, PCH_SPDWR, data->pkt_tx_buff[j]); |
| |
| /* update tx_index */ |
| data->tx_index = j; |
| |
| /* reset transfer complete flag */ |
| data->transfer_complete = false; |
| data->transfer_active = true; |
| } |
| |
| static void pch_spi_nomore_transfer(struct pch_spi_data *data) |
| { |
| struct spi_message *pmsg, *tmp; |
| dev_dbg(&data->master->dev, "%s called\n", __func__); |
| /* Invoke complete callback |
| * [To the spi core..indicating end of transfer] */ |
| data->current_msg->status = 0; |
| |
| if (data->current_msg->complete) { |
| dev_dbg(&data->master->dev, |
| "%s:Invoking callback of SPI core\n", __func__); |
| data->current_msg->complete(data->current_msg->context); |
| } |
| |
| /* update status in global variable */ |
| data->bcurrent_msg_processing = false; |
| |
| dev_dbg(&data->master->dev, |
| "%s:data->bcurrent_msg_processing = false\n", __func__); |
| |
| data->current_msg = NULL; |
| data->cur_trans = NULL; |
| |
| /* check if we have items in list and not suspending |
| * return 1 if list empty */ |
| if ((list_empty(&data->queue) == 0) && |
| (!data->board_dat->suspend_sts) && |
| (data->status != STATUS_EXITING)) { |
| /* We have some more work to do (either there is more tranint |
| * bpw;sfer requests in the current message or there are |
| *more messages) |
| */ |
| dev_dbg(&data->master->dev, "%s:Invoke queue_work\n", __func__); |
| schedule_work(&data->work); |
| } else if (data->board_dat->suspend_sts || |
| data->status == STATUS_EXITING) { |
| dev_dbg(&data->master->dev, |
| "%s suspend/remove initiated, flushing queue\n", |
| __func__); |
| list_for_each_entry_safe(pmsg, tmp, data->queue.next, queue) { |
| pmsg->status = -EIO; |
| |
| if (pmsg->complete) |
| pmsg->complete(pmsg->context); |
| |
| /* delete from queue */ |
| list_del_init(&pmsg->queue); |
| } |
| } |
| } |
| |
| static void pch_spi_set_ir(struct pch_spi_data *data) |
| { |
| /* enable interrupts, set threshold, enable SPI */ |
| if ((data->bpw_len) > PCH_MAX_FIFO_DEPTH) |
| /* set receive threshold to PCH_RX_THOLD */ |
| pch_spi_setclr_reg(data->master, PCH_SPCR, |
| PCH_RX_THOLD << SPCR_RFIC_FIELD | |
| SPCR_FIE_BIT | SPCR_RFIE_BIT | |
| SPCR_ORIE_BIT | SPCR_SPE_BIT, |
| MASK_RFIC_SPCR_BITS | PCH_ALL); |
| else |
| /* set receive threshold to maximum */ |
| pch_spi_setclr_reg(data->master, PCH_SPCR, |
| PCH_RX_THOLD_MAX << SPCR_RFIC_FIELD | |
| SPCR_FIE_BIT | SPCR_ORIE_BIT | |
| SPCR_SPE_BIT, |
| MASK_RFIC_SPCR_BITS | PCH_ALL); |
| |
| /* Wait until the transfer completes; go to sleep after |
| initiating the transfer. */ |
| dev_dbg(&data->master->dev, |
| "%s:waiting for transfer to get over\n", __func__); |
| |
| wait_event_interruptible(data->wait, data->transfer_complete); |
| |
| /* clear all interrupts */ |
| pch_spi_writereg(data->master, PCH_SPSR, |
| pch_spi_readreg(data->master, PCH_SPSR)); |
| /* Disable interrupts and SPI transfer */ |
| pch_spi_setclr_reg(data->master, PCH_SPCR, 0, PCH_ALL | SPCR_SPE_BIT); |
| /* clear FIFO */ |
| pch_spi_clear_fifo(data->master); |
| } |
| |
| static void pch_spi_copy_rx_data(struct pch_spi_data *data, int bpw) |
| { |
| int j; |
| u8 *rx_buf; |
| u16 *rx_sbuf; |
| |
| /* copy Rx Data */ |
| if (!data->cur_trans->rx_buf) |
| return; |
| |
| if (bpw == 8) { |
| rx_buf = data->cur_trans->rx_buf; |
| for (j = 0; j < data->bpw_len; j++) |
| *rx_buf++ = data->pkt_rx_buff[j] & 0xFF; |
| } else { |
| rx_sbuf = data->cur_trans->rx_buf; |
| for (j = 0; j < data->bpw_len; j++) |
| *rx_sbuf++ = data->pkt_rx_buff[j]; |
| } |
| } |
| |
| static void pch_spi_copy_rx_data_for_dma(struct pch_spi_data *data, int bpw) |
| { |
| int j; |
| u8 *rx_buf; |
| u16 *rx_sbuf; |
| const u8 *rx_dma_buf; |
| const u16 *rx_dma_sbuf; |
| |
| /* copy Rx Data */ |
| if (!data->cur_trans->rx_buf) |
| return; |
| |
| if (bpw == 8) { |
| rx_buf = data->cur_trans->rx_buf; |
| rx_dma_buf = data->dma.rx_buf_virt; |
| for (j = 0; j < data->bpw_len; j++) |
| *rx_buf++ = *rx_dma_buf++ & 0xFF; |
| data->cur_trans->rx_buf = rx_buf; |
| } else { |
| rx_sbuf = data->cur_trans->rx_buf; |
| rx_dma_sbuf = data->dma.rx_buf_virt; |
| for (j = 0; j < data->bpw_len; j++) |
| *rx_sbuf++ = *rx_dma_sbuf++; |
| data->cur_trans->rx_buf = rx_sbuf; |
| } |
| } |
| |
| static int pch_spi_start_transfer(struct pch_spi_data *data) |
| { |
| struct pch_spi_dma_ctrl *dma; |
| unsigned long flags; |
| int rtn; |
| |
| dma = &data->dma; |
| |
| spin_lock_irqsave(&data->lock, flags); |
| |
| /* disable interrupts, SPI set enable */ |
| pch_spi_setclr_reg(data->master, PCH_SPCR, SPCR_SPE_BIT, PCH_ALL); |
| |
| spin_unlock_irqrestore(&data->lock, flags); |
| |
| /* Wait until the transfer completes; go to sleep after |
| initiating the transfer. */ |
| dev_dbg(&data->master->dev, |
| "%s:waiting for transfer to get over\n", __func__); |
| rtn = wait_event_interruptible_timeout(data->wait, |
| data->transfer_complete, |
| msecs_to_jiffies(2 * HZ)); |
| if (!rtn) |
| dev_err(&data->master->dev, |
| "%s wait-event timeout\n", __func__); |
| |
| dma_sync_sg_for_cpu(&data->master->dev, dma->sg_rx_p, dma->nent, |
| DMA_FROM_DEVICE); |
| |
| dma_sync_sg_for_cpu(&data->master->dev, dma->sg_tx_p, dma->nent, |
| DMA_FROM_DEVICE); |
| memset(data->dma.tx_buf_virt, 0, PAGE_SIZE); |
| |
| async_tx_ack(dma->desc_rx); |
| async_tx_ack(dma->desc_tx); |
| kfree(dma->sg_tx_p); |
| kfree(dma->sg_rx_p); |
| |
| spin_lock_irqsave(&data->lock, flags); |
| |
| /* clear fifo threshold, disable interrupts, disable SPI transfer */ |
| pch_spi_setclr_reg(data->master, PCH_SPCR, 0, |
| MASK_RFIC_SPCR_BITS | MASK_TFIC_SPCR_BITS | PCH_ALL | |
| SPCR_SPE_BIT); |
| /* clear all interrupts */ |
| pch_spi_writereg(data->master, PCH_SPSR, |
| pch_spi_readreg(data->master, PCH_SPSR)); |
| /* clear FIFO */ |
| pch_spi_clear_fifo(data->master); |
| |
| spin_unlock_irqrestore(&data->lock, flags); |
| |
| return rtn; |
| } |
| |
| static void pch_dma_rx_complete(void *arg) |
| { |
| struct pch_spi_data *data = arg; |
| |
| /* transfer is completed;inform pch_spi_process_messages_dma */ |
| data->transfer_complete = true; |
| wake_up_interruptible(&data->wait); |
| } |
| |
| static bool pch_spi_filter(struct dma_chan *chan, void *slave) |
| { |
| struct pch_dma_slave *param = slave; |
| |
| if ((chan->chan_id == param->chan_id) && |
| (param->dma_dev == chan->device->dev)) { |
| chan->private = param; |
| return true; |
| } else { |
| return false; |
| } |
| } |
| |
| static void pch_spi_request_dma(struct pch_spi_data *data, int bpw) |
| { |
| dma_cap_mask_t mask; |
| struct dma_chan *chan; |
| struct pci_dev *dma_dev; |
| struct pch_dma_slave *param; |
| struct pch_spi_dma_ctrl *dma; |
| unsigned int width; |
| |
| if (bpw == 8) |
| width = PCH_DMA_WIDTH_1_BYTE; |
| else |
| width = PCH_DMA_WIDTH_2_BYTES; |
| |
| dma = &data->dma; |
| dma_cap_zero(mask); |
| dma_cap_set(DMA_SLAVE, mask); |
| |
| /* Get DMA's dev information */ |
| dma_dev = pci_get_slot(data->board_dat->pdev->bus, |
| PCI_DEVFN(PCI_SLOT(data->board_dat->pdev->devfn), 0)); |
| |
| /* Set Tx DMA */ |
| param = &dma->param_tx; |
| param->dma_dev = &dma_dev->dev; |
| param->chan_id = data->ch * 2; /* Tx = 0, 2 */ |
| param->tx_reg = data->io_base_addr + PCH_SPDWR; |
| param->width = width; |
| chan = dma_request_channel(mask, pch_spi_filter, param); |
| if (!chan) { |
| dev_err(&data->master->dev, |
| "ERROR: dma_request_channel FAILS(Tx)\n"); |
| data->use_dma = 0; |
| return; |
| } |
| dma->chan_tx = chan; |
| |
| /* Set Rx DMA */ |
| param = &dma->param_rx; |
| param->dma_dev = &dma_dev->dev; |
| param->chan_id = data->ch * 2 + 1; /* Rx = Tx + 1 */ |
| param->rx_reg = data->io_base_addr + PCH_SPDRR; |
| param->width = width; |
| chan = dma_request_channel(mask, pch_spi_filter, param); |
| if (!chan) { |
| dev_err(&data->master->dev, |
| "ERROR: dma_request_channel FAILS(Rx)\n"); |
| dma_release_channel(dma->chan_tx); |
| dma->chan_tx = NULL; |
| data->use_dma = 0; |
| return; |
| } |
| dma->chan_rx = chan; |
| } |
| |
| static void pch_spi_release_dma(struct pch_spi_data *data) |
| { |
| struct pch_spi_dma_ctrl *dma; |
| |
| dma = &data->dma; |
| if (dma->chan_tx) { |
| dma_release_channel(dma->chan_tx); |
| dma->chan_tx = NULL; |
| } |
| if (dma->chan_rx) { |
| dma_release_channel(dma->chan_rx); |
| dma->chan_rx = NULL; |
| } |
| } |
| |
| static void pch_spi_handle_dma(struct pch_spi_data *data, int *bpw) |
| { |
| const u8 *tx_buf; |
| const u16 *tx_sbuf; |
| u8 *tx_dma_buf; |
| u16 *tx_dma_sbuf; |
| struct scatterlist *sg; |
| struct dma_async_tx_descriptor *desc_tx; |
| struct dma_async_tx_descriptor *desc_rx; |
| int num; |
| int i; |
| int size; |
| int rem; |
| int head; |
| unsigned long flags; |
| struct pch_spi_dma_ctrl *dma; |
| |
| dma = &data->dma; |
| |
| /* set baud rate if needed */ |
| if (data->cur_trans->speed_hz) { |
| dev_dbg(&data->master->dev, "%s:setting baud rate\n", __func__); |
| spin_lock_irqsave(&data->lock, flags); |
| pch_spi_set_baud_rate(data->master, data->cur_trans->speed_hz); |
| spin_unlock_irqrestore(&data->lock, flags); |
| } |
| |
| /* set bits per word if needed */ |
| if (data->cur_trans->bits_per_word && |
| (data->current_msg->spi->bits_per_word != |
| data->cur_trans->bits_per_word)) { |
| dev_dbg(&data->master->dev, "%s:set bits per word\n", __func__); |
| spin_lock_irqsave(&data->lock, flags); |
| pch_spi_set_bits_per_word(data->master, |
| data->cur_trans->bits_per_word); |
| spin_unlock_irqrestore(&data->lock, flags); |
| *bpw = data->cur_trans->bits_per_word; |
| } else { |
| *bpw = data->current_msg->spi->bits_per_word; |
| } |
| data->bpw_len = data->cur_trans->len / (*bpw / 8); |
| |
| if (data->bpw_len > PCH_BUF_SIZE) { |
| data->bpw_len = PCH_BUF_SIZE; |
| data->cur_trans->len -= PCH_BUF_SIZE; |
| } |
| |
| /* copy Tx Data */ |
| if (data->cur_trans->tx_buf != NULL) { |
| if (*bpw == 8) { |
| tx_buf = data->cur_trans->tx_buf; |
| tx_dma_buf = dma->tx_buf_virt; |
| for (i = 0; i < data->bpw_len; i++) |
| *tx_dma_buf++ = *tx_buf++; |
| } else { |
| tx_sbuf = data->cur_trans->tx_buf; |
| tx_dma_sbuf = dma->tx_buf_virt; |
| for (i = 0; i < data->bpw_len; i++) |
| *tx_dma_sbuf++ = *tx_sbuf++; |
| } |
| } |
| |
| /* Calculate Rx parameter for DMA transmitting */ |
| if (data->bpw_len > PCH_DMA_TRANS_SIZE) { |
| if (data->bpw_len % PCH_DMA_TRANS_SIZE) { |
| num = data->bpw_len / PCH_DMA_TRANS_SIZE + 1; |
| rem = data->bpw_len % PCH_DMA_TRANS_SIZE; |
| } else { |
| num = data->bpw_len / PCH_DMA_TRANS_SIZE; |
| rem = PCH_DMA_TRANS_SIZE; |
| } |
| size = PCH_DMA_TRANS_SIZE; |
| } else { |
| num = 1; |
| size = data->bpw_len; |
| rem = data->bpw_len; |
| } |
| dev_dbg(&data->master->dev, "%s num=%d size=%d rem=%d\n", |
| __func__, num, size, rem); |
| spin_lock_irqsave(&data->lock, flags); |
| |
| /* set receive fifo threshold and transmit fifo threshold */ |
| pch_spi_setclr_reg(data->master, PCH_SPCR, |
| ((size - 1) << SPCR_RFIC_FIELD) | |
| (PCH_TX_THOLD << SPCR_TFIC_FIELD), |
| MASK_RFIC_SPCR_BITS | MASK_TFIC_SPCR_BITS); |
| |
| spin_unlock_irqrestore(&data->lock, flags); |
| |
| /* RX */ |
| dma->sg_rx_p = kcalloc(num, sizeof(*dma->sg_rx_p), GFP_ATOMIC); |
| if (!dma->sg_rx_p) |
| return; |
| |
| sg_init_table(dma->sg_rx_p, num); /* Initialize SG table */ |
| /* offset, length setting */ |
| sg = dma->sg_rx_p; |
| for (i = 0; i < num; i++, sg++) { |
| if (i == (num - 2)) { |
| sg->offset = size * i; |
| sg->offset = sg->offset * (*bpw / 8); |
| sg_set_page(sg, virt_to_page(dma->rx_buf_virt), rem, |
| sg->offset); |
| sg_dma_len(sg) = rem; |
| } else if (i == (num - 1)) { |
| sg->offset = size * (i - 1) + rem; |
| sg->offset = sg->offset * (*bpw / 8); |
| sg_set_page(sg, virt_to_page(dma->rx_buf_virt), size, |
| sg->offset); |
| sg_dma_len(sg) = size; |
| } else { |
| sg->offset = size * i; |
| sg->offset = sg->offset * (*bpw / 8); |
| sg_set_page(sg, virt_to_page(dma->rx_buf_virt), size, |
| sg->offset); |
| sg_dma_len(sg) = size; |
| } |
| sg_dma_address(sg) = dma->rx_buf_dma + sg->offset; |
| } |
| sg = dma->sg_rx_p; |
| desc_rx = dmaengine_prep_slave_sg(dma->chan_rx, sg, |
| num, DMA_DEV_TO_MEM, |
| DMA_PREP_INTERRUPT | DMA_CTRL_ACK); |
| if (!desc_rx) { |
| dev_err(&data->master->dev, |
| "%s:dmaengine_prep_slave_sg Failed\n", __func__); |
| return; |
| } |
| dma_sync_sg_for_device(&data->master->dev, sg, num, DMA_FROM_DEVICE); |
| desc_rx->callback = pch_dma_rx_complete; |
| desc_rx->callback_param = data; |
| dma->nent = num; |
| dma->desc_rx = desc_rx; |
| |
| /* Calculate Tx parameter for DMA transmitting */ |
| if (data->bpw_len > PCH_MAX_FIFO_DEPTH) { |
| head = PCH_MAX_FIFO_DEPTH - PCH_DMA_TRANS_SIZE; |
| if (data->bpw_len % PCH_DMA_TRANS_SIZE > 4) { |
| num = data->bpw_len / PCH_DMA_TRANS_SIZE + 1; |
| rem = data->bpw_len % PCH_DMA_TRANS_SIZE - head; |
| } else { |
| num = data->bpw_len / PCH_DMA_TRANS_SIZE; |
| rem = data->bpw_len % PCH_DMA_TRANS_SIZE + |
| PCH_DMA_TRANS_SIZE - head; |
| } |
| size = PCH_DMA_TRANS_SIZE; |
| } else { |
| num = 1; |
| size = data->bpw_len; |
| rem = data->bpw_len; |
| head = 0; |
| } |
| |
| dma->sg_tx_p = kcalloc(num, sizeof(*dma->sg_tx_p), GFP_ATOMIC); |
| if (!dma->sg_tx_p) |
| return; |
| |
| sg_init_table(dma->sg_tx_p, num); /* Initialize SG table */ |
| /* offset, length setting */ |
| sg = dma->sg_tx_p; |
| for (i = 0; i < num; i++, sg++) { |
| if (i == 0) { |
| sg->offset = 0; |
| sg_set_page(sg, virt_to_page(dma->tx_buf_virt), size + head, |
| sg->offset); |
| sg_dma_len(sg) = size + head; |
| } else if (i == (num - 1)) { |
| sg->offset = head + size * i; |
| sg->offset = sg->offset * (*bpw / 8); |
| sg_set_page(sg, virt_to_page(dma->tx_buf_virt), rem, |
| sg->offset); |
| sg_dma_len(sg) = rem; |
| } else { |
| sg->offset = head + size * i; |
| sg->offset = sg->offset * (*bpw / 8); |
| sg_set_page(sg, virt_to_page(dma->tx_buf_virt), size, |
| sg->offset); |
| sg_dma_len(sg) = size; |
| } |
| sg_dma_address(sg) = dma->tx_buf_dma + sg->offset; |
| } |
| sg = dma->sg_tx_p; |
| desc_tx = dmaengine_prep_slave_sg(dma->chan_tx, |
| sg, num, DMA_MEM_TO_DEV, |
| DMA_PREP_INTERRUPT | DMA_CTRL_ACK); |
| if (!desc_tx) { |
| dev_err(&data->master->dev, |
| "%s:dmaengine_prep_slave_sg Failed\n", __func__); |
| return; |
| } |
| dma_sync_sg_for_device(&data->master->dev, sg, num, DMA_TO_DEVICE); |
| desc_tx->callback = NULL; |
| desc_tx->callback_param = data; |
| dma->nent = num; |
| dma->desc_tx = desc_tx; |
| |
| dev_dbg(&data->master->dev, "%s:Pulling down SSN low - writing 0x2 to SSNXCR\n", __func__); |
| |
| spin_lock_irqsave(&data->lock, flags); |
| pch_spi_writereg(data->master, PCH_SSNXCR, SSN_LOW); |
| desc_rx->tx_submit(desc_rx); |
| desc_tx->tx_submit(desc_tx); |
| spin_unlock_irqrestore(&data->lock, flags); |
| |
| /* reset transfer complete flag */ |
| data->transfer_complete = false; |
| } |
| |
| static void pch_spi_process_messages(struct work_struct *pwork) |
| { |
| struct spi_message *pmsg, *tmp; |
| struct pch_spi_data *data; |
| int bpw; |
| |
| data = container_of(pwork, struct pch_spi_data, work); |
| dev_dbg(&data->master->dev, "%s data initialized\n", __func__); |
| |
| spin_lock(&data->lock); |
| /* check if suspend has been initiated;if yes flush queue */ |
| if (data->board_dat->suspend_sts || (data->status == STATUS_EXITING)) { |
| dev_dbg(&data->master->dev, |
| "%s suspend/remove initiated, flushing queue\n", __func__); |
| list_for_each_entry_safe(pmsg, tmp, data->queue.next, queue) { |
| pmsg->status = -EIO; |
| |
| if (pmsg->complete) { |
| spin_unlock(&data->lock); |
| pmsg->complete(pmsg->context); |
| spin_lock(&data->lock); |
| } |
| |
| /* delete from queue */ |
| list_del_init(&pmsg->queue); |
| } |
| |
| spin_unlock(&data->lock); |
| return; |
| } |
| |
| data->bcurrent_msg_processing = true; |
| dev_dbg(&data->master->dev, |
| "%s Set data->bcurrent_msg_processing= true\n", __func__); |
| |
| /* Get the message from the queue and delete it from there. */ |
| data->current_msg = list_entry(data->queue.next, struct spi_message, |
| queue); |
| |
| list_del_init(&data->current_msg->queue); |
| |
| data->current_msg->status = 0; |
| |
| pch_spi_select_chip(data, data->current_msg->spi); |
| |
| spin_unlock(&data->lock); |
| |
| if (data->use_dma) |
| pch_spi_request_dma(data, |
| data->current_msg->spi->bits_per_word); |
| pch_spi_writereg(data->master, PCH_SSNXCR, SSN_NO_CONTROL); |
| do { |
| int cnt; |
| /* If we are already processing a message get the next |
| transfer structure from the message otherwise retrieve |
| the 1st transfer request from the message. */ |
| spin_lock(&data->lock); |
| if (data->cur_trans == NULL) { |
| data->cur_trans = |
| list_entry(data->current_msg->transfers.next, |
| struct spi_transfer, transfer_list); |
| dev_dbg(&data->master->dev, |
| "%s :Getting 1st transfer message\n", |
| __func__); |
| } else { |
| data->cur_trans = |
| list_entry(data->cur_trans->transfer_list.next, |
| struct spi_transfer, transfer_list); |
| dev_dbg(&data->master->dev, |
| "%s :Getting next transfer message\n", |
| __func__); |
| } |
| spin_unlock(&data->lock); |
| |
| if (!data->cur_trans->len) |
| goto out; |
| cnt = (data->cur_trans->len - 1) / PCH_BUF_SIZE + 1; |
| data->save_total_len = data->cur_trans->len; |
| if (data->use_dma) { |
| int i; |
| char *save_rx_buf = data->cur_trans->rx_buf; |
| for (i = 0; i < cnt; i ++) { |
| pch_spi_handle_dma(data, &bpw); |
| if (!pch_spi_start_transfer(data)) { |
| data->transfer_complete = true; |
| data->current_msg->status = -EIO; |
| data->current_msg->complete |
| (data->current_msg->context); |
| data->bcurrent_msg_processing = false; |
| data->current_msg = NULL; |
| data->cur_trans = NULL; |
| goto out; |
| } |
| pch_spi_copy_rx_data_for_dma(data, bpw); |
| } |
| data->cur_trans->rx_buf = save_rx_buf; |
| } else { |
| pch_spi_set_tx(data, &bpw); |
| pch_spi_set_ir(data); |
| pch_spi_copy_rx_data(data, bpw); |
| kfree(data->pkt_rx_buff); |
| data->pkt_rx_buff = NULL; |
| kfree(data->pkt_tx_buff); |
| data->pkt_tx_buff = NULL; |
| } |
| /* increment message count */ |
| data->cur_trans->len = data->save_total_len; |
| data->current_msg->actual_length += data->cur_trans->len; |
| |
| dev_dbg(&data->master->dev, |
| "%s:data->current_msg->actual_length=%d\n", |
| __func__, data->current_msg->actual_length); |
| |
| spi_transfer_delay_exec(data->cur_trans); |
| |
| spin_lock(&data->lock); |
| |
| /* No more transfer in this message. */ |
| if ((data->cur_trans->transfer_list.next) == |
| &(data->current_msg->transfers)) { |
| pch_spi_nomore_transfer(data); |
| } |
| |
| spin_unlock(&data->lock); |
| |
| } while (data->cur_trans != NULL); |
| |
| out: |
| pch_spi_writereg(data->master, PCH_SSNXCR, SSN_HIGH); |
| if (data->use_dma) |
| pch_spi_release_dma(data); |
| } |
| |
| static void pch_spi_free_resources(struct pch_spi_board_data *board_dat, |
| struct pch_spi_data *data) |
| { |
| dev_dbg(&board_dat->pdev->dev, "%s ENTRY\n", __func__); |
| |
| flush_work(&data->work); |
| } |
| |
| static int pch_spi_get_resources(struct pch_spi_board_data *board_dat, |
| struct pch_spi_data *data) |
| { |
| dev_dbg(&board_dat->pdev->dev, "%s ENTRY\n", __func__); |
| |
| /* reset PCH SPI h/w */ |
| pch_spi_reset(data->master); |
| dev_dbg(&board_dat->pdev->dev, |
| "%s pch_spi_reset invoked successfully\n", __func__); |
| |
| dev_dbg(&board_dat->pdev->dev, "%s data->irq_reg_sts=true\n", __func__); |
| |
| return 0; |
| } |
| |
| static void pch_free_dma_buf(struct pch_spi_board_data *board_dat, |
| struct pch_spi_data *data) |
| { |
| struct pch_spi_dma_ctrl *dma; |
| |
| dma = &data->dma; |
| if (dma->tx_buf_dma) |
| dma_free_coherent(&board_dat->pdev->dev, PCH_BUF_SIZE, |
| dma->tx_buf_virt, dma->tx_buf_dma); |
| if (dma->rx_buf_dma) |
| dma_free_coherent(&board_dat->pdev->dev, PCH_BUF_SIZE, |
| dma->rx_buf_virt, dma->rx_buf_dma); |
| } |
| |
| static int pch_alloc_dma_buf(struct pch_spi_board_data *board_dat, |
| struct pch_spi_data *data) |
| { |
| struct pch_spi_dma_ctrl *dma; |
| int ret; |
| |
| dma = &data->dma; |
| ret = 0; |
| /* Get Consistent memory for Tx DMA */ |
| dma->tx_buf_virt = dma_alloc_coherent(&board_dat->pdev->dev, |
| PCH_BUF_SIZE, &dma->tx_buf_dma, GFP_KERNEL); |
| if (!dma->tx_buf_virt) |
| ret = -ENOMEM; |
| |
| /* Get Consistent memory for Rx DMA */ |
| dma->rx_buf_virt = dma_alloc_coherent(&board_dat->pdev->dev, |
| PCH_BUF_SIZE, &dma->rx_buf_dma, GFP_KERNEL); |
| if (!dma->rx_buf_virt) |
| ret = -ENOMEM; |
| |
| return ret; |
| } |
| |
| static int pch_spi_pd_probe(struct platform_device *plat_dev) |
| { |
| int ret; |
| struct spi_master *master; |
| struct pch_spi_board_data *board_dat = dev_get_platdata(&plat_dev->dev); |
| struct pch_spi_data *data; |
| |
| dev_dbg(&plat_dev->dev, "%s:debug\n", __func__); |
| |
| master = spi_alloc_master(&board_dat->pdev->dev, |
| sizeof(struct pch_spi_data)); |
| if (!master) { |
| dev_err(&plat_dev->dev, "spi_alloc_master[%d] failed.\n", |
| plat_dev->id); |
| return -ENOMEM; |
| } |
| |
| data = spi_master_get_devdata(master); |
| data->master = master; |
| |
| platform_set_drvdata(plat_dev, data); |
| |
| /* baseaddress + address offset) */ |
| data->io_base_addr = pci_resource_start(board_dat->pdev, 1) + |
| PCH_ADDRESS_SIZE * plat_dev->id; |
| data->io_remap_addr = pci_iomap(board_dat->pdev, 1, 0); |
| if (!data->io_remap_addr) { |
| dev_err(&plat_dev->dev, "%s pci_iomap failed\n", __func__); |
| ret = -ENOMEM; |
| goto err_pci_iomap; |
| } |
| data->io_remap_addr += PCH_ADDRESS_SIZE * plat_dev->id; |
| |
| dev_dbg(&plat_dev->dev, "[ch%d] remap_addr=%p\n", |
| plat_dev->id, data->io_remap_addr); |
| |
| /* initialize members of SPI master */ |
| master->num_chipselect = PCH_MAX_CS; |
| master->transfer = pch_spi_transfer; |
| master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST; |
| master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16); |
| master->max_speed_hz = PCH_MAX_BAUDRATE; |
| |
| data->board_dat = board_dat; |
| data->plat_dev = plat_dev; |
| data->n_curnt_chip = 255; |
| data->status = STATUS_RUNNING; |
| data->ch = plat_dev->id; |
| data->use_dma = use_dma; |
| |
| INIT_LIST_HEAD(&data->queue); |
| spin_lock_init(&data->lock); |
| INIT_WORK(&data->work, pch_spi_process_messages); |
| init_waitqueue_head(&data->wait); |
| |
| ret = pch_spi_get_resources(board_dat, data); |
| if (ret) { |
| dev_err(&plat_dev->dev, "%s fail(retval=%d)\n", __func__, ret); |
| goto err_spi_get_resources; |
| } |
| |
| ret = request_irq(board_dat->pdev->irq, pch_spi_handler, |
| IRQF_SHARED, KBUILD_MODNAME, data); |
| if (ret) { |
| dev_err(&plat_dev->dev, |
| "%s request_irq failed\n", __func__); |
| goto err_request_irq; |
| } |
| data->irq_reg_sts = true; |
| |
| pch_spi_set_master_mode(master); |
| |
| if (use_dma) { |
| dev_info(&plat_dev->dev, "Use DMA for data transfers\n"); |
| ret = pch_alloc_dma_buf(board_dat, data); |
| if (ret) |
| goto err_spi_register_master; |
| } |
| |
| ret = spi_register_master(master); |
| if (ret != 0) { |
| dev_err(&plat_dev->dev, |
| "%s spi_register_master FAILED\n", __func__); |
| goto err_spi_register_master; |
| } |
| |
| return 0; |
| |
| err_spi_register_master: |
| pch_free_dma_buf(board_dat, data); |
| free_irq(board_dat->pdev->irq, data); |
| err_request_irq: |
| pch_spi_free_resources(board_dat, data); |
| err_spi_get_resources: |
| pci_iounmap(board_dat->pdev, data->io_remap_addr); |
| err_pci_iomap: |
| spi_master_put(master); |
| |
| return ret; |
| } |
| |
| static int pch_spi_pd_remove(struct platform_device *plat_dev) |
| { |
| struct pch_spi_board_data *board_dat = dev_get_platdata(&plat_dev->dev); |
| struct pch_spi_data *data = platform_get_drvdata(plat_dev); |
| int count; |
| unsigned long flags; |
| |
| dev_dbg(&plat_dev->dev, "%s:[ch%d] irq=%d\n", |
| __func__, plat_dev->id, board_dat->pdev->irq); |
| |
| if (use_dma) |
| pch_free_dma_buf(board_dat, data); |
| |
| /* check for any pending messages; no action is taken if the queue |
| * is still full; but at least we tried. Unload anyway */ |
| count = 500; |
| spin_lock_irqsave(&data->lock, flags); |
| data->status = STATUS_EXITING; |
| while ((list_empty(&data->queue) == 0) && --count) { |
| dev_dbg(&board_dat->pdev->dev, "%s :queue not empty\n", |
| __func__); |
| spin_unlock_irqrestore(&data->lock, flags); |
| msleep(PCH_SLEEP_TIME); |
| spin_lock_irqsave(&data->lock, flags); |
| } |
| spin_unlock_irqrestore(&data->lock, flags); |
| |
| pch_spi_free_resources(board_dat, data); |
| /* disable interrupts & free IRQ */ |
| if (data->irq_reg_sts) { |
| /* disable interrupts */ |
| pch_spi_setclr_reg(data->master, PCH_SPCR, 0, PCH_ALL); |
| data->irq_reg_sts = false; |
| free_irq(board_dat->pdev->irq, data); |
| } |
| |
| pci_iounmap(board_dat->pdev, data->io_remap_addr); |
| spi_unregister_master(data->master); |
| |
| return 0; |
| } |
| #ifdef CONFIG_PM |
| static int pch_spi_pd_suspend(struct platform_device *pd_dev, |
| pm_message_t state) |
| { |
| u8 count; |
| struct pch_spi_board_data *board_dat = dev_get_platdata(&pd_dev->dev); |
| struct pch_spi_data *data = platform_get_drvdata(pd_dev); |
| |
| dev_dbg(&pd_dev->dev, "%s ENTRY\n", __func__); |
| |
| if (!board_dat) { |
| dev_err(&pd_dev->dev, |
| "%s pci_get_drvdata returned NULL\n", __func__); |
| return -EFAULT; |
| } |
| |
| /* check if the current message is processed: |
| Only after thats done the transfer will be suspended */ |
| count = 255; |
| while ((--count) > 0) { |
| if (!(data->bcurrent_msg_processing)) |
| break; |
| msleep(PCH_SLEEP_TIME); |
| } |
| |
| /* Free IRQ */ |
| if (data->irq_reg_sts) { |
| /* disable all interrupts */ |
| pch_spi_setclr_reg(data->master, PCH_SPCR, 0, PCH_ALL); |
| pch_spi_reset(data->master); |
| free_irq(board_dat->pdev->irq, data); |
| |
| data->irq_reg_sts = false; |
| dev_dbg(&pd_dev->dev, |
| "%s free_irq invoked successfully.\n", __func__); |
| } |
| |
| return 0; |
| } |
| |
| static int pch_spi_pd_resume(struct platform_device *pd_dev) |
| { |
| struct pch_spi_board_data *board_dat = dev_get_platdata(&pd_dev->dev); |
| struct pch_spi_data *data = platform_get_drvdata(pd_dev); |
| int retval; |
| |
| if (!board_dat) { |
| dev_err(&pd_dev->dev, |
| "%s pci_get_drvdata returned NULL\n", __func__); |
| return -EFAULT; |
| } |
| |
| if (!data->irq_reg_sts) { |
| /* register IRQ */ |
| retval = request_irq(board_dat->pdev->irq, pch_spi_handler, |
| IRQF_SHARED, KBUILD_MODNAME, data); |
| if (retval < 0) { |
| dev_err(&pd_dev->dev, |
| "%s request_irq failed\n", __func__); |
| return retval; |
| } |
| |
| /* reset PCH SPI h/w */ |
| pch_spi_reset(data->master); |
| pch_spi_set_master_mode(data->master); |
| data->irq_reg_sts = true; |
| } |
| return 0; |
| } |
| #else |
| #define pch_spi_pd_suspend NULL |
| #define pch_spi_pd_resume NULL |
| #endif |
| |
| static struct platform_driver pch_spi_pd_driver = { |
| .driver = { |
| .name = "pch-spi", |
| }, |
| .probe = pch_spi_pd_probe, |
| .remove = pch_spi_pd_remove, |
| .suspend = pch_spi_pd_suspend, |
| .resume = pch_spi_pd_resume |
| }; |
| |
| static int pch_spi_probe(struct pci_dev *pdev, const struct pci_device_id *id) |
| { |
| struct pch_spi_board_data *board_dat; |
| struct platform_device *pd_dev = NULL; |
| int retval; |
| int i; |
| struct pch_pd_dev_save *pd_dev_save; |
| |
| pd_dev_save = kzalloc(sizeof(*pd_dev_save), GFP_KERNEL); |
| if (!pd_dev_save) |
| return -ENOMEM; |
| |
| board_dat = kzalloc(sizeof(*board_dat), GFP_KERNEL); |
| if (!board_dat) { |
| retval = -ENOMEM; |
| goto err_no_mem; |
| } |
| |
| retval = pci_request_regions(pdev, KBUILD_MODNAME); |
| if (retval) { |
| dev_err(&pdev->dev, "%s request_region failed\n", __func__); |
| goto pci_request_regions; |
| } |
| |
| board_dat->pdev = pdev; |
| board_dat->num = id->driver_data; |
| pd_dev_save->num = id->driver_data; |
| pd_dev_save->board_dat = board_dat; |
| |
| retval = pci_enable_device(pdev); |
| if (retval) { |
| dev_err(&pdev->dev, "%s pci_enable_device failed\n", __func__); |
| goto pci_enable_device; |
| } |
| |
| for (i = 0; i < board_dat->num; i++) { |
| pd_dev = platform_device_alloc("pch-spi", i); |
| if (!pd_dev) { |
| dev_err(&pdev->dev, "platform_device_alloc failed\n"); |
| retval = -ENOMEM; |
| goto err_platform_device; |
| } |
| pd_dev_save->pd_save[i] = pd_dev; |
| pd_dev->dev.parent = &pdev->dev; |
| |
| retval = platform_device_add_data(pd_dev, board_dat, |
| sizeof(*board_dat)); |
| if (retval) { |
| dev_err(&pdev->dev, |
| "platform_device_add_data failed\n"); |
| platform_device_put(pd_dev); |
| goto err_platform_device; |
| } |
| |
| retval = platform_device_add(pd_dev); |
| if (retval) { |
| dev_err(&pdev->dev, "platform_device_add failed\n"); |
| platform_device_put(pd_dev); |
| goto err_platform_device; |
| } |
| } |
| |
| pci_set_drvdata(pdev, pd_dev_save); |
| |
| return 0; |
| |
| err_platform_device: |
| while (--i >= 0) |
| platform_device_unregister(pd_dev_save->pd_save[i]); |
| pci_disable_device(pdev); |
| pci_enable_device: |
| pci_release_regions(pdev); |
| pci_request_regions: |
| kfree(board_dat); |
| err_no_mem: |
| kfree(pd_dev_save); |
| |
| return retval; |
| } |
| |
| static void pch_spi_remove(struct pci_dev *pdev) |
| { |
| int i; |
| struct pch_pd_dev_save *pd_dev_save = pci_get_drvdata(pdev); |
| |
| dev_dbg(&pdev->dev, "%s ENTRY:pdev=%p\n", __func__, pdev); |
| |
| for (i = 0; i < pd_dev_save->num; i++) |
| platform_device_unregister(pd_dev_save->pd_save[i]); |
| |
| pci_disable_device(pdev); |
| pci_release_regions(pdev); |
| kfree(pd_dev_save->board_dat); |
| kfree(pd_dev_save); |
| } |
| |
| #ifdef CONFIG_PM |
| static int pch_spi_suspend(struct pci_dev *pdev, pm_message_t state) |
| { |
| int retval; |
| struct pch_pd_dev_save *pd_dev_save = pci_get_drvdata(pdev); |
| |
| dev_dbg(&pdev->dev, "%s ENTRY\n", __func__); |
| |
| pd_dev_save->board_dat->suspend_sts = true; |
| |
| /* save config space */ |
| retval = pci_save_state(pdev); |
| if (retval == 0) { |
| pci_enable_wake(pdev, PCI_D3hot, 0); |
| pci_disable_device(pdev); |
| pci_set_power_state(pdev, PCI_D3hot); |
| } else { |
| dev_err(&pdev->dev, "%s pci_save_state failed\n", __func__); |
| } |
| |
| return retval; |
| } |
| |
| static int pch_spi_resume(struct pci_dev *pdev) |
| { |
| int retval; |
| struct pch_pd_dev_save *pd_dev_save = pci_get_drvdata(pdev); |
| dev_dbg(&pdev->dev, "%s ENTRY\n", __func__); |
| |
| pci_set_power_state(pdev, PCI_D0); |
| pci_restore_state(pdev); |
| |
| retval = pci_enable_device(pdev); |
| if (retval < 0) { |
| dev_err(&pdev->dev, |
| "%s pci_enable_device failed\n", __func__); |
| } else { |
| pci_enable_wake(pdev, PCI_D3hot, 0); |
| |
| /* set suspend status to false */ |
| pd_dev_save->board_dat->suspend_sts = false; |
| } |
| |
| return retval; |
| } |
| #else |
| #define pch_spi_suspend NULL |
| #define pch_spi_resume NULL |
| |
| #endif |
| |
| static struct pci_driver pch_spi_pcidev_driver = { |
| .name = "pch_spi", |
| .id_table = pch_spi_pcidev_id, |
| .probe = pch_spi_probe, |
| .remove = pch_spi_remove, |
| .suspend = pch_spi_suspend, |
| .resume = pch_spi_resume, |
| }; |
| |
| static int __init pch_spi_init(void) |
| { |
| int ret; |
| ret = platform_driver_register(&pch_spi_pd_driver); |
| if (ret) |
| return ret; |
| |
| ret = pci_register_driver(&pch_spi_pcidev_driver); |
| if (ret) { |
| platform_driver_unregister(&pch_spi_pd_driver); |
| return ret; |
| } |
| |
| return 0; |
| } |
| module_init(pch_spi_init); |
| |
| static void __exit pch_spi_exit(void) |
| { |
| pci_unregister_driver(&pch_spi_pcidev_driver); |
| platform_driver_unregister(&pch_spi_pd_driver); |
| } |
| module_exit(pch_spi_exit); |
| |
| module_param(use_dma, int, 0644); |
| MODULE_PARM_DESC(use_dma, |
| "to use DMA for data transfers pass 1 else 0; default 1"); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_DESCRIPTION("Intel EG20T PCH/LAPIS Semiconductor ML7xxx IOH SPI Driver"); |
| MODULE_DEVICE_TABLE(pci, pch_spi_pcidev_id); |
| |