blob: ff7f39d29dd55139573caa21131695006ef48ca2 [file] [log] [blame]
// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2021, AngeloGioacchino Del Regno
* <angelogioacchino.delregno@somainline.org>
* Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
*/
#include "msm8996.dtsi"
#include "pm8994.dtsi"
#include "pmi8994.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
/delete-node/ &slpi_region;
/delete-node/ &venus_region;
/delete-node/ &zap_shader_region;
/ {
qcom,msm-id = <246 0x30001>; /* MSM8996 V3.1 (Final) */
qcom,pmic-id = <0x20009 0x2000a 0 0>; /* PM8994 + PMI8994 */
qcom,board-id = <8 0>;
chosen {
/*
* Due to an unknown-for-a-few-years regression,
* SDHCI only works on MSM8996 in PIO (lame) mode.
*/
bootargs = "sdhci.debug_quirks=0x40 sdhci.debug_quirks2=0x4 maxcpus=2";
};
reserved-memory {
ramoops@a7f00000 {
compatible = "ramoops";
reg = <0 0xa7f00000 0 0x100000>;
record-size = <0x20000>;
console-size = <0x40000>;
ftrace-size = <0x20000>;
pmsg-size = <0x20000>;
ecc-size = <16>;
};
cont_splash_mem: memory@83401000 {
reg = <0 0x83401000 0 0x23ff000>;
no-map;
};
zap_shader_region: gpu@90400000 {
compatible = "shared-dma-pool";
reg = <0x0 0x90400000 0x0 0x2000>;
no-map;
};
slpi_region: memory@90500000 {
reg = <0 0x90500000 0 0xa00000>;
no-map;
};
venus_region: memory@90f00000 {
reg = <0 0x90f00000 0 0x500000>;
no-map;
};
};
panel_tvdd: tvdd-regulator {
compatible = "regulator-fixed";
regulator-name = "panel_tvdd";
gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&tp_vddio_en>;
pinctrl-names = "default";
};
usb3_id: usb3-id {
compatible = "linux,extcon-usb-gpio";
id-gpio = <&tlmm 25 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&usb_detect>;
};
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-min-microvolt = <3700000>;
regulator-max-microvolt = <3700000>;
regulator-name = "vph_pwr";
regulator-always-on;
regulator-boot-on;
};
wlan_en: wlan-en-1-8v {
compatible = "regulator-fixed";
regulator-name = "wlan-en-regulator";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&wl_reg_on>;
/* WLAN card specific delay */
startup-delay-us = <70000>;
enable-active-high;
};
};
&blsp1_i2c3 {
status = "okay";
clock-frequency = <355000>;
tof_sensor: vl53l0x@29 {
compatible = "st,vl53l0x";
reg = <0x29>;
};
};
&blsp1_uart2 {
status = "okay";
};
&blsp2_i2c5 {
status = "okay";
clock-frequency = <355000>;
/* FUSB301 USB-C controller */
};
&blsp2_i2c6 {
status = "okay";
clock-frequency = <355000>;
synaptics@2c {
compatible = "syna,rmi4-i2c";
reg = <0x2c>;
interrupt-parent = <&tlmm>;
interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&panel_tvdd>;
syna,reset-delay-ms = <220>;
syna,startup-delay-ms = <220>;
#address-cells = <1>;
#size-cells = <0>;
rmi4-f01@1 {
reg = <0x1>;
syna,nosleep-mode = <1>;
};
rmi4-f11@11 {
reg = <0x11>;
syna,sensor-type = <1>;
};
};
};
&blsp2_uart2 {
status = "okay";
};
&camera0_mclk {
drive-strength = <2>;
output-low;
};
&camera0_pwdn {
drive-strength = <2>;
output-low;
};
&camera0_rst {
pins = "gpio30";
drive-strength = <2>;
output-low;
};
&camera2_mclk {
drive-strength = <2>;
output-low;
};
&camera2_rst {
drive-strength = <2>;
output-low;
};
&hsusb_phy1 {
status = "okay";
vdda-pll-supply = <&pm8994_l12>;
vdda-phy-dpdm-supply = <&pm8994_l24>;
};
&mmcc {
vdd-gfx-supply = <&vdd_gfx>;
};
&pcie0 {
status = "okay";
perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
wake-gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>;
vddpe-3v3-supply = <&wlan_en>;
vdda-supply = <&pm8994_l28>;
};
&pcie_phy {
status = "okay";
vdda-phy-supply = <&pm8994_l28>;
vdda-pll-supply = <&pm8994_l12>;
};
&pm8994_gpios {
pinctrl-names = "default";
pinctrl-0 = <&pm8994_gpios_defaults>;
gpio-line-names =
"NC",
"VOL_DOWN_N",
"VOL_UP_N",
"SNAPSHOT_N",
"FOCUS_N",
"NC",
"NFC_VEN",
"NC",
"NC",
"NC",
"NC",
"NC",
"EAR_EN",
"NC",
"PM_DIVCLK1",
"PMI_CLK",
"NC",
"WL_SLEEP_CLK",
"NC",
"PMIC_SPON",
"UIM_BATT_ALARM",
"PMK_SLEEP_CLK";
/*
* We don't yet know for sure which GPIOs are of our interest, but what
* we do know is that if a vendor sets the pins to a non-default state, there's
* probably a reason for it, and just to be on the safe side, we follow suit.
*/
pm8994_gpios_defaults: pm8994-gpios-default-state {
pm8994-gpio1-nc {
pins = "gpio1";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
bias-high-impedance;
};
vol-down-n {
pins = "gpio2";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
input-enable;
bias-pull-up;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8994_GPIO_S4>;
};
vol-up-n {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
input-enable;
bias-pull-up;
power-source = <PM8994_GPIO_S4>;
};
camera-snapshot-n {
pins = "gpio4";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
input-enable;
bias-pull-up;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8994_GPIO_S4>;
};
camera-focus-n {
pins = "gpio5";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
input-enable;
bias-pull-up;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8994_GPIO_S4>;
};
pm8994-gpio6-nc {
pins = "gpio6";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
bias-high-impedance;
power-source = <PM8994_GPIO_VPH>;
};
nfc-download {
pins = "gpio7";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
drive-push-pull;
bias-disable;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
power-source = <PM8994_GPIO_S4>;
};
pm8994-gpio8-nc {
pins = "gpio8";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
drive-push-pull;
bias-high-impedance;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8994_GPIO_VPH>;
};
pm8994-gpio9-nc {
pins = "gpio9";
function = PMIC_GPIO_FUNC_NORMAL;
output-high;
drive-push-pull;
bias-high-impedance;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
power-source = <PM8994_GPIO_VPH>;
};
nfc-clock {
pins = "gpio10";
function = PMIC_GPIO_FUNC_NORMAL;
input-enable;
drive-push-pull;
bias-pull-down;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8994_GPIO_S4>;
};
pm8994-gpio11-nc {
pins = "gpio11";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
bias-high-impedance;
power-source = <PM8994_GPIO_VPH>;
};
pm8994-gpio12-nc {
pins = "gpio12";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
bias-high-impedance;
power-source = <PM8994_GPIO_VPH>;
};
ear-enable {
pins = "gpio13";
function = PMIC_GPIO_FUNC_NORMAL;
output-high;
drive-push-pull;
bias-disable;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
power-source = <PM8994_GPIO_S4>;
};
pm8994-gpio14-nc {
pins = "gpio14";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
input-enable;
bias-high-impedance;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
power-source = <PM8994_GPIO_VPH>;
};
pm-divclk1-gpio {
pins = "gpio15";
function = "func1";
output-high;
drive-push-pull;
bias-high-impedance;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
power-source = <PM8994_GPIO_VPH>;
};
pmi-clk-gpio {
pins = "gpio16";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
};
pm8994-gpio17-nc {
pins = "gpio17";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
bias-high-impedance;
power-source = <PM8994_GPIO_VPH>;
};
rome-sleep {
pins = "gpio18";
function = PMIC_GPIO_FUNC_FUNC2;
output-low;
drive-push-pull;
bias-disable;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_MED>;
power-source = <PM8994_GPIO_S4>;
};
pm8994-gpio19-nc {
pins = "gpio19";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
drive-push-pull;
bias-high-impedance;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8994_GPIO_VPH>;
};
pm8994-gpio22-nc {
pins = "gpio22";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
bias-high-impedance;
power-source = <PM8994_GPIO_VPH>;
};
};
};
&pm8994_mpps {
pinctrl-names = "default";
pinctrl-0 = <&pm8994_mpps_defaults>;
gpio-line-names =
"SDC_UIM_VBIAS",
"LCD_ID_ADC",
"VREF_DACX",
"NC",
"FLASH_THERM",
"NC",
"NC",
"RF_ID";
pm8994_mpps_defaults: pm8994-mpps-default-state {
lcd-id_adc-mpp {
pins = "mpp2";
function = "analog";
input-enable;
qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH6>;
};
pm-mpp4-nc {
pins = "mpp4";
function = "digital";
bias-high-impedance;
power-source = <PM8994_GPIO_VPH>;
};
flash-therm-mpp {
pins = "mpp5";
function = "analog";
input-enable;
qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
};
mpp6-nc {
pins = "mpp6";
function = "digital";
bias-high-impedance;
};
rf-id-mpp {
pins = "mpp8";
function = "analog";
input-enable;
qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH8>;
};
};
};
&pm8994_resin {
status = "okay";
linux,code = <KEY_VOLUMEUP>;
};
&pmi8994_gpios {
pinctrl-names = "default";
pinctrl-0 = <&pmi8994_gpios_defaults>;
gpio-line-names =
"VIB_LDO_EN",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"USB_SWITCH_SEL",
"NC";
pmi8994_gpios_defaults: pmi8994-gpios-default-state {
vib-ldo-en-gpio {
pins = "gpio1";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
output-low;
bias-disable;
power-source = <PM8994_GPIO_S4>;
};
pmi-gpio2-nc {
pins = "gpio2";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
input-enable;
bias-high-impedance;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8994_GPIO_VPH>;
};
pmi-gpio3-nc {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
input-enable;
bias-high-impedance;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8994_GPIO_VPH>;
};
pmi-gpio4-nc {
pins = "gpio4";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
output-high;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
power-source = <PM8994_GPIO_S4>;
};
pmi-gpio5-nc {
pins = "gpio5";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
output-high;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8994_GPIO_S4>;
};
pmi-gpio6-nc {
pins = "gpio6";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
output-high;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
power-source = <PM8994_GPIO_S4>;
};
pmi-gpio7-nc {
pins = "gpio7";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
output-high;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
power-source = <PM8994_GPIO_S4>;
};
pmi-gpio8-nc {
pins = "gpio8";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
output-high;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
power-source = <PM8994_GPIO_S4>;
};
usb-switch-sel {
pins = "gpio9";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
};
pmi-gpio10-nc {
pins = "gpio10";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
drive-push-pull;
bias-disable;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8994_GPIO_S4>;
};
};
};
&pmi8994_spmi_regulators {
qcom,saw-reg = <&saw3>;
vdd_gfx:
pmi8994_s2: s2 {
/* Pinned to a high value for now to avoid random crashes. */
regulator-min-microvolt = <1015000>;
regulator-max-microvolt = <1015000>;
regulator-name = "vdd_gfx";
regulator-always-on;
};
pmi8994_s9: s9 {
qcom,saw-slave;
};
pmi8994_s10: s10 {
qcom,saw-slave;
};
pmi8994_s11: s11 {
qcom,saw-leader;
regulator-always-on;
regulator-min-microvolt = <470000>;
regulator-max-microvolt = <1140000>;
};
};
&pmi8994_wled {
status = "okay";
default-brightness = <512>;
qcom,num-strings = <3>;
};
&rpm_requests {
pm8994-regulators {
compatible = "qcom,rpm-pm8994-regulators";
vdd_s1-supply = <&vph_pwr>;
vdd_s2-supply = <&vph_pwr>;
vdd_s3-supply = <&vph_pwr>;
vdd_s4-supply = <&vph_pwr>;
vdd_s5-supply = <&vph_pwr>;
vdd_s6-supply = <&vph_pwr>;
vdd_s7-supply = <&vph_pwr>;
vdd_s8-supply = <&vph_pwr>;
vdd_s9-supply = <&vph_pwr>;
vdd_s10-supply = <&vph_pwr>;
vdd_s11-supply = <&vph_pwr>;
vdd_s12-supply = <&vph_pwr>;
vdd_l1-supply = <&pm8994_s3>;
vdd_l2_l26_l28-supply = <&pm8994_s3>;
vdd_l3_l11-supply = <&pm8994_s3>;
vdd_l4_l27_l31-supply = <&pm8994_s3>;
vdd_l5_l7-supply = <&pm8994_s5>;
vdd_l6_l12_l32-supply = <&pm8994_s5>;
vdd_l8_l16_l30-supply = <&vph_pwr>;
vdd_l14_l15-supply = <&pm8994_s5>;
vdd_l20_l21-supply = <&pm8994_s5>;
vdd_l25-supply = <&pm8994_s3>;
vdd_lvs1_2-supply = <&pm8994_s4>;
pm8994_s3: s3 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
};
pm8994_s4: s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-system-load = <325000>;
regulator-always-on;
};
pm8994_s5: s5 {
regulator-min-microvolt = <2150000>;
regulator-max-microvolt = <2150000>;
};
pm8994_s7: s7 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
};
pm8994_l1: l1 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
pm8994_l2: l2 {
regulator-min-microvolt = <1250000>;
regulator-max-microvolt = <1250000>;
};
pm8994_l3: l3 {
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
pm8994_l4: l4 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
/* L6 and L7 seem unused. */
pm8994_l8: l8 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8994_l9: l9 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8994_l10: l10 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8994_l11: l11 {
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
pm8994_l12: l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-allow-set-load;
};
pm8994_l13: l13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
regulator-system-load = <22000>;
regulator-allow-set-load;
};
pm8994_l14: l14 {
regulator-min-microvolt = <1700000>;
regulator-max-microvolt = <1900000>;
};
pm8994_l15: l15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8994_l16: l16 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
pm8994_l17: l17 {
regulator-min-microvolt = <2200000>;
regulator-max-microvolt = <2500000>;
};
pm8994_l18: l18 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8994_l19: l19 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
pm8994_l20: l20 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-system-load = <570000>;
regulator-allow-set-load;
};
pm8994_l21: l21 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-system-load = <800000>;
regulator-allow-set-load;
};
pm8994_l22: l22 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
pm8994_l23: l23 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
pm8994_l24: l24 {
regulator-min-microvolt = <3075000>;
regulator-max-microvolt = <3075000>;
regulator-allow-set-load;
};
pm8994_l25: l25 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-allow-set-load;
};
pm8994_l27: l27 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1200000>;
};
pm8994_l28: l28 {
regulator-min-microvolt = <925000>;
regulator-max-microvolt = <925000>;
regulator-allow-set-load;
};
pm8994_l29: l29 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
pm8994_l30: l30 { };
pm8994_l32: l32 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
};
};
&sdhc1 {
/* eMMC doesn't seem to cooperate even in PIO mode.. */
status = "disabled";
vmmc-supply = <&pm8994_l20>;
vqmmc-supply = <&pm8994_s4>;
mmc-hs400-1_8v;
mmc-hs200-1_8v;
};
&sdhc2 {
status = "okay";
cd-gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
vmmc-supply = <&pm8994_l21>;
vqmmc-supply = <&pm8994_l13>;
};
&tlmm {
gpio-reserved-ranges = <0 4>;
pinctrl-0 = <&sw_service_gpio>;
pinctrl-names = "default";
disp_reset_n_gpio: disp-reset-n {
pins = "gpio8";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
mdp_vsync_p_gpio: mdp-vsync-p {
pins = "gpio10";
function = "mdp_vsync";
drive-strength = <2>;
bias-disable;
};
sw_service_gpio: sw-service-gpio {
pins = "gpio16";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
usb_detect: usb-detect {
pins = "gpio25";
function = "gpio";
drive-strength = <2>;
bias-disable;
output-high;
};
uim_detect_en: uim-detect-en {
pins = "gpio29";
function = "gpio";
drive-strength = <2>;
bias-disable;
output-high;
};
tray_det_pin: tray-det {
pins = "gpio40";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
tp_vddio_en: tp-vddio-en {
pins = "gpio50";
function = "gpio";
drive-strength = <2>;
bias-disable;
output-high;
};
lcd_vddio_en: lcd-vddio-en {
pins = "gpio51";
function = "gpio";
drive-strength = <2>;
bias-disable;
output-low;
};
wl_host_wake: wl-host-wake {
pins = "gpio79";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
input-high;
};
wl_reg_on: wl-reg-on {
pins = "gpio84";
function = "gpio";
drive-strength = <2>;
bias-disable;
output-low;
};
ts_reset_n: ts-rst-n {
pins = "gpio89";
function = "gpio";
drive-strength = <2>;
};
touch_int_n: touch-int-n {
pins = "gpio125";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
touch_int_sleep: touch-int-sleep {
pins = "gpio125";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
};
/*
* For reasons that are currently unknown (but probably related to fusb301), USB takes about
* 6 minutes to wake up (nothing interesting in kernel logs), but then it works as it should.
*/
&usb3 {
status = "okay";
qcom,select-utmi-as-pipe-clk;
};
&usb3_dwc3 {
extcon = <&usb3_id>;
dr_mode = "peripheral";
phys = <&hsusb_phy1>;
phy-names = "usb2-phy";
snps,hird-threshold = /bits/ 8 <0>;
};