blob: 8b79fbb75756939e24cca79d9c37d4a90817079c [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Google Lazor board device tree source
*
* Copyright 2020 Google LLC.
*/
#include "sc7180.dtsi"
ap_ec_spi: &spi6 {};
ap_h1_spi: &spi0 {};
#include "sc7180-trogdor.dtsi"
#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
&ap_sar_sensor {
semtech,cs0-ground;
semtech,combined-sensors = <3>;
semtech,resolution = "fine";
semtech,startup-sensor = <0>;
semtech,proxraw-strength = <8>;
semtech,avg-pos-strength = <64>;
};
/*
* Lazor is stuffed with a 47k NTC as charger thermistor which currently is
* not supported by the PM6150 ADC driver. Disable the charger thermal zone
* to avoid using bogus temperature values.
*/
&charger_thermal {
status = "disabled";
};
ap_ts_pen_1v8: &i2c4 {
status = "okay";
clock-frequency = <400000>;
ap_ts: touchscreen@10 {
compatible = "hid-over-i2c";
reg = <0x10>;
pinctrl-names = "default";
pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
interrupt-parent = <&tlmm>;
interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
post-power-on-delay-ms = <20>;
hid-descr-addr = <0x0001>;
vdd-supply = <&pp3300_ts>;
};
};
&panel {
compatible = "boe,nv133fhm-n62";
};
&pm6150_adc {
status = "disabled";
/delete-node/ charger-thermistor@4f;
};
&pm6150_adc_tm {
status = "disabled";
/delete-node/ charger-thermistor@0;
};
&trackpad {
interrupts = <58 IRQ_TYPE_EDGE_FALLING>;
};
&wifi {
qcom,ath10k-calibration-variant = "GO_LAZOR";
};
/* PINCTRL - modifications to sc7180-trogdor.dtsi */
&trackpad_int_1v8_odl {
pinmux {
pins = "gpio58";
};
pinconf {
pins = "gpio58";
};
};
&ts_reset_l {
pinconf {
/* This pin is not connected on -rev0, pull up to park. */
/delete-property/bias-disable;
bias-pull-up;
};
};
/* PINCTRL - board-specific pinctrl */
&tlmm {
gpio-line-names = "ESIM_MISO",
"ESIM_MOSI",
"ESIM_CLK",
"ESIM_CS_L",
"",
"",
"AP_TP_I2C_SDA",
"AP_TP_I2C_SCL",
"TS_RESET_L",
"TS_INT_L",
"",
"EDP_BRIJ_IRQ",
"AP_EDP_BKLTEN",
"AP_RAM_ID2",
"",
"EDP_BRIJ_I2C_SDA",
"EDP_BRIJ_I2C_SCL",
"HUB_RST_L",
"",
"AP_RAM_ID1",
"AP_SKU_ID2",
"",
"",
"AMP_EN",
"P_SENSOR_INT_L",
"AP_SAR_SENSOR_SDA",
"AP_SAR_SENSOR_SCL",
"",
"HP_IRQ",
"AP_RAM_ID0",
"EN_PP3300_DX_EDP",
"AP_BRD_ID2",
"BRIJ_SUSPEND",
"AP_BRD_ID0",
"AP_H1_SPI_MISO",
"AP_H1_SPI_MOSI",
"AP_H1_SPI_CLK",
"AP_H1_SPI_CS_L",
"",
"",
"",
"",
"H1_AP_INT_ODL",
"",
"UART_AP_TX_DBG_RX",
"UART_DBG_TX_AP_RX",
"HP_I2C_SDA",
"HP_I2C_SCL",
"FORCED_USB_BOOT",
"",
"",
"AMP_DIN",
"",
"HP_BCLK",
"HP_LRCLK",
"HP_DOUT",
"HP_DIN",
"HP_MCLK",
"TRACKPAD_INT_1V8_ODL",
"AP_EC_SPI_MISO",
"AP_EC_SPI_MOSI",
"AP_EC_SPI_CLK",
"AP_EC_SPI_CS_L",
"AP_SPI_CLK",
"AP_SPI_MOSI",
"AP_SPI_MISO",
/*
* AP_FLASH_WP_L is crossystem ABI. Schematics
* call it BIOS_FLASH_WP_L.
*/
"AP_FLASH_WP_L",
"DBG_SPI_HOLD_L",
"AP_SPI_CS0_L",
"",
"",
"",
"",
"",
"",
"UIM2_DATA",
"UIM2_CLK",
"UIM2_RST",
"UIM2_PRESENT",
"UIM1_DATA",
"UIM1_CLK",
"UIM1_RST",
"",
"EN_PP3300_CODEC",
"EN_PP3300_HUB",
"",
"",
"",
"",
"",
"AP_SKU_ID1",
"AP_RST_REQ",
"",
"AP_BRD_ID1",
"AP_EC_INT_L",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"EDP_BRIJ_EN",
"AP_SKU_ID0",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"AP_TS_PEN_I2C_SDA",
"AP_TS_PEN_I2C_SCL",
"DP_HOT_PLUG_DET",
"EC_IN_RW_ODL";
};