| // SPDX-License-Identifier: GPL-2.0 |
| // Copyright (C) 2018 Microchip Technology |
| |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/delay.h> |
| #include <linux/mii.h> |
| #include <linux/phy.h> |
| #include <linux/ethtool.h> |
| #include <linux/ethtool_netlink.h> |
| #include <linux/bitfield.h> |
| |
| #define PHY_ID_LAN87XX 0x0007c150 |
| #define PHY_ID_LAN937X 0x0007c180 |
| |
| /* External Register Control Register */ |
| #define LAN87XX_EXT_REG_CTL (0x14) |
| #define LAN87XX_EXT_REG_CTL_RD_CTL (0x1000) |
| #define LAN87XX_EXT_REG_CTL_WR_CTL (0x0800) |
| #define LAN87XX_REG_BANK_SEL_MASK GENMASK(10, 8) |
| #define LAN87XX_REG_ADDR_MASK GENMASK(7, 0) |
| |
| /* External Register Read Data Register */ |
| #define LAN87XX_EXT_REG_RD_DATA (0x15) |
| |
| /* External Register Write Data Register */ |
| #define LAN87XX_EXT_REG_WR_DATA (0x16) |
| |
| /* Interrupt Source Register */ |
| #define LAN87XX_INTERRUPT_SOURCE (0x18) |
| |
| /* Interrupt Mask Register */ |
| #define LAN87XX_INTERRUPT_MASK (0x19) |
| #define LAN87XX_MASK_LINK_UP (0x0004) |
| #define LAN87XX_MASK_LINK_DOWN (0x0002) |
| |
| /* MISC Control 1 Register */ |
| #define LAN87XX_CTRL_1 (0x11) |
| #define LAN87XX_MASK_RGMII_TXC_DLY_EN (0x4000) |
| #define LAN87XX_MASK_RGMII_RXC_DLY_EN (0x2000) |
| |
| /* phyaccess nested types */ |
| #define PHYACC_ATTR_MODE_READ 0 |
| #define PHYACC_ATTR_MODE_WRITE 1 |
| #define PHYACC_ATTR_MODE_MODIFY 2 |
| #define PHYACC_ATTR_MODE_POLL 3 |
| |
| #define PHYACC_ATTR_BANK_SMI 0 |
| #define PHYACC_ATTR_BANK_MISC 1 |
| #define PHYACC_ATTR_BANK_PCS 2 |
| #define PHYACC_ATTR_BANK_AFE 3 |
| #define PHYACC_ATTR_BANK_DSP 4 |
| #define PHYACC_ATTR_BANK_MAX 7 |
| |
| /* measurement defines */ |
| #define LAN87XX_CABLE_TEST_OK 0 |
| #define LAN87XX_CABLE_TEST_OPEN 1 |
| #define LAN87XX_CABLE_TEST_SAME_SHORT 2 |
| |
| /* T1 Registers */ |
| #define T1_AFE_PORT_CFG1_REG 0x0B |
| #define T1_POWER_DOWN_CONTROL_REG 0x1A |
| #define T1_SLV_FD_MULT_CFG_REG 0x18 |
| #define T1_CDR_CFG_PRE_LOCK_REG 0x05 |
| #define T1_CDR_CFG_POST_LOCK_REG 0x06 |
| #define T1_LCK_STG2_MUFACT_CFG_REG 0x1A |
| #define T1_LCK_STG3_MUFACT_CFG_REG 0x1B |
| #define T1_POST_LCK_MUFACT_CFG_REG 0x1C |
| #define T1_TX_RX_FIFO_CFG_REG 0x02 |
| #define T1_TX_LPF_FIR_CFG_REG 0x55 |
| #define T1_SQI_CONFIG_REG 0x2E |
| #define T1_MDIO_CONTROL2_REG 0x10 |
| #define T1_INTERRUPT_SOURCE_REG 0x18 |
| #define T1_INTERRUPT2_SOURCE_REG 0x08 |
| #define T1_EQ_FD_STG1_FRZ_CFG 0x69 |
| #define T1_EQ_FD_STG2_FRZ_CFG 0x6A |
| #define T1_EQ_FD_STG3_FRZ_CFG 0x6B |
| #define T1_EQ_FD_STG4_FRZ_CFG 0x6C |
| #define T1_EQ_WT_FD_LCK_FRZ_CFG 0x6D |
| #define T1_PST_EQ_LCK_STG1_FRZ_CFG 0x6E |
| |
| #define T1_MODE_STAT_REG 0x11 |
| #define T1_LINK_UP_MSK BIT(0) |
| |
| #define DRIVER_AUTHOR "Nisar Sayed <nisar.sayed@microchip.com>" |
| #define DRIVER_DESC "Microchip LAN87XX/LAN937x T1 PHY driver" |
| |
| struct access_ereg_val { |
| u8 mode; |
| u8 bank; |
| u8 offset; |
| u16 val; |
| u16 mask; |
| }; |
| |
| static int lan937x_dsp_workaround(struct phy_device *phydev, u16 ereg, u8 bank) |
| { |
| u8 prev_bank; |
| int rc = 0; |
| u16 val; |
| |
| mutex_lock(&phydev->lock); |
| /* Read previous selected bank */ |
| rc = phy_read(phydev, LAN87XX_EXT_REG_CTL); |
| if (rc < 0) |
| goto out_unlock; |
| |
| /* store the prev_bank */ |
| prev_bank = FIELD_GET(LAN87XX_REG_BANK_SEL_MASK, rc); |
| |
| if (bank != prev_bank && bank == PHYACC_ATTR_BANK_DSP) { |
| val = ereg & ~LAN87XX_REG_ADDR_MASK; |
| |
| val &= ~LAN87XX_EXT_REG_CTL_WR_CTL; |
| val |= LAN87XX_EXT_REG_CTL_RD_CTL; |
| |
| /* access twice for DSP bank change,dummy access */ |
| rc = phy_write(phydev, LAN87XX_EXT_REG_CTL, val); |
| } |
| |
| out_unlock: |
| mutex_unlock(&phydev->lock); |
| |
| return rc; |
| } |
| |
| static int access_ereg(struct phy_device *phydev, u8 mode, u8 bank, |
| u8 offset, u16 val) |
| { |
| u16 ereg = 0; |
| int rc = 0; |
| |
| if (mode > PHYACC_ATTR_MODE_WRITE || bank > PHYACC_ATTR_BANK_MAX) |
| return -EINVAL; |
| |
| if (bank == PHYACC_ATTR_BANK_SMI) { |
| if (mode == PHYACC_ATTR_MODE_WRITE) |
| rc = phy_write(phydev, offset, val); |
| else |
| rc = phy_read(phydev, offset); |
| return rc; |
| } |
| |
| if (mode == PHYACC_ATTR_MODE_WRITE) { |
| ereg = LAN87XX_EXT_REG_CTL_WR_CTL; |
| rc = phy_write(phydev, LAN87XX_EXT_REG_WR_DATA, val); |
| if (rc < 0) |
| return rc; |
| } else { |
| ereg = LAN87XX_EXT_REG_CTL_RD_CTL; |
| } |
| |
| ereg |= (bank << 8) | offset; |
| |
| /* DSP bank access workaround for lan937x */ |
| if (phydev->phy_id == PHY_ID_LAN937X) { |
| rc = lan937x_dsp_workaround(phydev, ereg, bank); |
| if (rc < 0) |
| return rc; |
| } |
| |
| rc = phy_write(phydev, LAN87XX_EXT_REG_CTL, ereg); |
| if (rc < 0) |
| return rc; |
| |
| if (mode == PHYACC_ATTR_MODE_READ) |
| rc = phy_read(phydev, LAN87XX_EXT_REG_RD_DATA); |
| |
| return rc; |
| } |
| |
| static int access_ereg_modify_changed(struct phy_device *phydev, |
| u8 bank, u8 offset, u16 val, u16 mask) |
| { |
| int new = 0, rc = 0; |
| |
| if (bank > PHYACC_ATTR_BANK_MAX) |
| return -EINVAL; |
| |
| rc = access_ereg(phydev, PHYACC_ATTR_MODE_READ, bank, offset, val); |
| if (rc < 0) |
| return rc; |
| |
| new = val | (rc & (mask ^ 0xFFFF)); |
| rc = access_ereg(phydev, PHYACC_ATTR_MODE_WRITE, bank, offset, new); |
| |
| return rc; |
| } |
| |
| static int access_smi_poll_timeout(struct phy_device *phydev, |
| u8 offset, u16 mask, u16 clr) |
| { |
| int val; |
| |
| return phy_read_poll_timeout(phydev, offset, val, (val & mask) == clr, |
| 150, 30000, true); |
| } |
| |
| static int lan87xx_config_rgmii_delay(struct phy_device *phydev) |
| { |
| int rc; |
| |
| if (!phy_interface_is_rgmii(phydev)) |
| return 0; |
| |
| rc = access_ereg(phydev, PHYACC_ATTR_MODE_READ, |
| PHYACC_ATTR_BANK_MISC, LAN87XX_CTRL_1, 0); |
| if (rc < 0) |
| return rc; |
| |
| switch (phydev->interface) { |
| case PHY_INTERFACE_MODE_RGMII: |
| rc &= ~LAN87XX_MASK_RGMII_TXC_DLY_EN; |
| rc &= ~LAN87XX_MASK_RGMII_RXC_DLY_EN; |
| break; |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| rc |= LAN87XX_MASK_RGMII_TXC_DLY_EN; |
| rc |= LAN87XX_MASK_RGMII_RXC_DLY_EN; |
| break; |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| rc &= ~LAN87XX_MASK_RGMII_TXC_DLY_EN; |
| rc |= LAN87XX_MASK_RGMII_RXC_DLY_EN; |
| break; |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| rc |= LAN87XX_MASK_RGMII_TXC_DLY_EN; |
| rc &= ~LAN87XX_MASK_RGMII_RXC_DLY_EN; |
| break; |
| default: |
| return 0; |
| } |
| |
| return access_ereg(phydev, PHYACC_ATTR_MODE_WRITE, |
| PHYACC_ATTR_BANK_MISC, LAN87XX_CTRL_1, rc); |
| } |
| |
| static int lan87xx_phy_init(struct phy_device *phydev) |
| { |
| static const struct access_ereg_val init[] = { |
| /* TXPD/TXAMP6 Configs */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_AFE, |
| T1_AFE_PORT_CFG1_REG, 0x002D, 0 }, |
| /* HW_Init Hi and Force_ED */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_SMI, |
| T1_POWER_DOWN_CONTROL_REG, 0x0308, 0 }, |
| /* Equalizer Full Duplex Freeze - T1 Slave */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_EQ_FD_STG1_FRZ_CFG, 0x0002, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_EQ_FD_STG2_FRZ_CFG, 0x0002, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_EQ_FD_STG3_FRZ_CFG, 0x0002, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_EQ_FD_STG4_FRZ_CFG, 0x0002, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_EQ_WT_FD_LCK_FRZ_CFG, 0x0002, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_PST_EQ_LCK_STG1_FRZ_CFG, 0x0002, 0 }, |
| /* Slave Full Duplex Multi Configs */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_SLV_FD_MULT_CFG_REG, 0x0D53, 0 }, |
| /* CDR Pre and Post Lock Configs */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_CDR_CFG_PRE_LOCK_REG, 0x0AB2, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_CDR_CFG_POST_LOCK_REG, 0x0AB3, 0 }, |
| /* Lock Stage 2-3 Multi Factor Config */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_LCK_STG2_MUFACT_CFG_REG, 0x0AEA, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_LCK_STG3_MUFACT_CFG_REG, 0x0AEB, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_POST_LCK_MUFACT_CFG_REG, 0x0AEB, 0 }, |
| /* Pointer delay */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_RX_FIFO_CFG_REG, 0x1C00, 0 }, |
| /* Tx iir edits */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1000, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1861, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1061, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1922, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1122, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1983, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1183, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1944, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1144, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x18c5, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x10c5, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1846, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1046, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1807, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1007, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1808, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1008, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1809, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1009, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x180A, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x100A, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x180B, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x100B, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x180C, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x100C, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x180D, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x100D, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x180E, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x100E, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x180F, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x100F, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1810, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1010, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1811, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1011, 0 }, |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_TX_LPF_FIR_CFG_REG, 0x1000, 0 }, |
| /* SQI enable */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, |
| T1_SQI_CONFIG_REG, 0x9572, 0 }, |
| /* Flag LPS and WUR as idle errors */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_SMI, |
| T1_MDIO_CONTROL2_REG, 0x0014, 0 }, |
| /* HW_Init toggle, undo force ED, TXPD off */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_SMI, |
| T1_POWER_DOWN_CONTROL_REG, 0x0200, 0 }, |
| /* Reset PCS to trigger hardware initialization */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_SMI, |
| T1_MDIO_CONTROL2_REG, 0x0094, 0 }, |
| /* Poll till Hardware is initialized */ |
| { PHYACC_ATTR_MODE_POLL, PHYACC_ATTR_BANK_SMI, |
| T1_MDIO_CONTROL2_REG, 0x0080, 0 }, |
| /* Tx AMP - 0x06 */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_AFE, |
| T1_AFE_PORT_CFG1_REG, 0x000C, 0 }, |
| /* Read INTERRUPT_SOURCE Register */ |
| { PHYACC_ATTR_MODE_READ, PHYACC_ATTR_BANK_SMI, |
| T1_INTERRUPT_SOURCE_REG, 0, 0 }, |
| /* Read INTERRUPT_SOURCE Register */ |
| { PHYACC_ATTR_MODE_READ, PHYACC_ATTR_BANK_MISC, |
| T1_INTERRUPT2_SOURCE_REG, 0, 0 }, |
| /* HW_Init Hi */ |
| { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_SMI, |
| T1_POWER_DOWN_CONTROL_REG, 0x0300, 0 }, |
| }; |
| int rc, i; |
| |
| /* phy Soft reset */ |
| rc = genphy_soft_reset(phydev); |
| if (rc < 0) |
| return rc; |
| |
| /* PHY Initialization */ |
| for (i = 0; i < ARRAY_SIZE(init); i++) { |
| if (init[i].mode == PHYACC_ATTR_MODE_POLL && |
| init[i].bank == PHYACC_ATTR_BANK_SMI) { |
| rc = access_smi_poll_timeout(phydev, |
| init[i].offset, |
| init[i].val, |
| init[i].mask); |
| } else { |
| rc = access_ereg(phydev, init[i].mode, init[i].bank, |
| init[i].offset, init[i].val); |
| } |
| if (rc < 0) |
| return rc; |
| } |
| |
| return lan87xx_config_rgmii_delay(phydev); |
| } |
| |
| static int lan87xx_phy_config_intr(struct phy_device *phydev) |
| { |
| int rc, val = 0; |
| |
| if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { |
| /* unmask all source and clear them before enable */ |
| rc = phy_write(phydev, LAN87XX_INTERRUPT_MASK, 0x7FFF); |
| rc = phy_read(phydev, LAN87XX_INTERRUPT_SOURCE); |
| val = LAN87XX_MASK_LINK_UP | LAN87XX_MASK_LINK_DOWN; |
| rc = phy_write(phydev, LAN87XX_INTERRUPT_MASK, val); |
| } else { |
| rc = phy_write(phydev, LAN87XX_INTERRUPT_MASK, val); |
| if (rc) |
| return rc; |
| |
| rc = phy_read(phydev, LAN87XX_INTERRUPT_SOURCE); |
| } |
| |
| return rc < 0 ? rc : 0; |
| } |
| |
| static irqreturn_t lan87xx_handle_interrupt(struct phy_device *phydev) |
| { |
| int irq_status; |
| |
| irq_status = phy_read(phydev, LAN87XX_INTERRUPT_SOURCE); |
| if (irq_status < 0) { |
| phy_error(phydev); |
| return IRQ_NONE; |
| } |
| |
| if (irq_status == 0) |
| return IRQ_NONE; |
| |
| phy_trigger_machine(phydev); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int lan87xx_config_init(struct phy_device *phydev) |
| { |
| int rc = lan87xx_phy_init(phydev); |
| |
| return rc < 0 ? rc : 0; |
| } |
| |
| static int microchip_cable_test_start_common(struct phy_device *phydev) |
| { |
| int bmcr, bmsr, ret; |
| |
| /* If auto-negotiation is enabled, but not complete, the cable |
| * test never completes. So disable auto-neg. |
| */ |
| bmcr = phy_read(phydev, MII_BMCR); |
| if (bmcr < 0) |
| return bmcr; |
| |
| bmsr = phy_read(phydev, MII_BMSR); |
| |
| if (bmsr < 0) |
| return bmsr; |
| |
| if (bmcr & BMCR_ANENABLE) { |
| ret = phy_modify(phydev, MII_BMCR, BMCR_ANENABLE, 0); |
| if (ret < 0) |
| return ret; |
| ret = genphy_soft_reset(phydev); |
| if (ret < 0) |
| return ret; |
| } |
| |
| /* If the link is up, allow it some time to go down */ |
| if (bmsr & BMSR_LSTATUS) |
| msleep(1500); |
| |
| return 0; |
| } |
| |
| static int lan87xx_cable_test_start(struct phy_device *phydev) |
| { |
| static const struct access_ereg_val cable_test[] = { |
| /* min wait */ |
| {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, 93, |
| 0, 0}, |
| /* max wait */ |
| {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, 94, |
| 10, 0}, |
| /* pulse cycle */ |
| {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, 95, |
| 90, 0}, |
| /* cable diag thresh */ |
| {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, 92, |
| 60, 0}, |
| /* max gain */ |
| {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, 79, |
| 31, 0}, |
| /* clock align for each iteration */ |
| {PHYACC_ATTR_MODE_MODIFY, PHYACC_ATTR_BANK_DSP, 55, |
| 0, 0x0038}, |
| /* max cycle wait config */ |
| {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, 94, |
| 70, 0}, |
| /* start cable diag*/ |
| {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP, 90, |
| 1, 0}, |
| }; |
| int rc, i; |
| |
| rc = microchip_cable_test_start_common(phydev); |
| if (rc < 0) |
| return rc; |
| |
| /* start cable diag */ |
| /* check if part is alive - if not, return diagnostic error */ |
| rc = access_ereg(phydev, PHYACC_ATTR_MODE_READ, PHYACC_ATTR_BANK_SMI, |
| 0x00, 0); |
| if (rc < 0) |
| return rc; |
| |
| /* master/slave specific configs */ |
| rc = access_ereg(phydev, PHYACC_ATTR_MODE_READ, PHYACC_ATTR_BANK_SMI, |
| 0x0A, 0); |
| if (rc < 0) |
| return rc; |
| |
| if ((rc & 0x4000) != 0x4000) { |
| /* DUT is Slave */ |
| rc = access_ereg_modify_changed(phydev, PHYACC_ATTR_BANK_AFE, |
| 0x0E, 0x5, 0x7); |
| if (rc < 0) |
| return rc; |
| rc = access_ereg_modify_changed(phydev, PHYACC_ATTR_BANK_SMI, |
| 0x1A, 0x8, 0x8); |
| if (rc < 0) |
| return rc; |
| } else { |
| /* DUT is Master */ |
| rc = access_ereg_modify_changed(phydev, PHYACC_ATTR_BANK_SMI, |
| 0x10, 0x8, 0x40); |
| if (rc < 0) |
| return rc; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(cable_test); i++) { |
| if (cable_test[i].mode == PHYACC_ATTR_MODE_MODIFY) { |
| rc = access_ereg_modify_changed(phydev, |
| cable_test[i].bank, |
| cable_test[i].offset, |
| cable_test[i].val, |
| cable_test[i].mask); |
| /* wait 50ms */ |
| msleep(50); |
| } else { |
| rc = access_ereg(phydev, cable_test[i].mode, |
| cable_test[i].bank, |
| cable_test[i].offset, |
| cable_test[i].val); |
| } |
| if (rc < 0) |
| return rc; |
| } |
| /* cable diag started */ |
| |
| return 0; |
| } |
| |
| static int lan87xx_cable_test_report_trans(u32 result) |
| { |
| switch (result) { |
| case LAN87XX_CABLE_TEST_OK: |
| return ETHTOOL_A_CABLE_RESULT_CODE_OK; |
| case LAN87XX_CABLE_TEST_OPEN: |
| return ETHTOOL_A_CABLE_RESULT_CODE_OPEN; |
| case LAN87XX_CABLE_TEST_SAME_SHORT: |
| return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT; |
| default: |
| /* DIAGNOSTIC_ERROR */ |
| return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC; |
| } |
| } |
| |
| static int lan87xx_cable_test_report(struct phy_device *phydev) |
| { |
| int pos_peak_cycle = 0, pos_peak_in_phases = 0, pos_peak_phase = 0; |
| int neg_peak_cycle = 0, neg_peak_in_phases = 0, neg_peak_phase = 0; |
| int noise_margin = 20, time_margin = 89, jitter_var = 30; |
| int min_time_diff = 96, max_time_diff = 96 + time_margin; |
| bool fault = false, check_a = false, check_b = false; |
| int gain_idx = 0, pos_peak = 0, neg_peak = 0; |
| int pos_peak_time = 0, neg_peak_time = 0; |
| int pos_peak_in_phases_hybrid = 0; |
| int detect = -1; |
| |
| gain_idx = access_ereg(phydev, PHYACC_ATTR_MODE_READ, |
| PHYACC_ATTR_BANK_DSP, 151, 0); |
| /* read non-hybrid results */ |
| pos_peak = access_ereg(phydev, PHYACC_ATTR_MODE_READ, |
| PHYACC_ATTR_BANK_DSP, 153, 0); |
| neg_peak = access_ereg(phydev, PHYACC_ATTR_MODE_READ, |
| PHYACC_ATTR_BANK_DSP, 154, 0); |
| pos_peak_time = access_ereg(phydev, PHYACC_ATTR_MODE_READ, |
| PHYACC_ATTR_BANK_DSP, 156, 0); |
| neg_peak_time = access_ereg(phydev, PHYACC_ATTR_MODE_READ, |
| PHYACC_ATTR_BANK_DSP, 157, 0); |
| |
| pos_peak_cycle = (pos_peak_time >> 7) & 0x7F; |
| /* calculate non-hybrid values */ |
| pos_peak_phase = pos_peak_time & 0x7F; |
| pos_peak_in_phases = (pos_peak_cycle * 96) + pos_peak_phase; |
| neg_peak_cycle = (neg_peak_time >> 7) & 0x7F; |
| neg_peak_phase = neg_peak_time & 0x7F; |
| neg_peak_in_phases = (neg_peak_cycle * 96) + neg_peak_phase; |
| |
| /* process values */ |
| check_a = |
| ((pos_peak_in_phases - neg_peak_in_phases) >= min_time_diff) && |
| ((pos_peak_in_phases - neg_peak_in_phases) < max_time_diff) && |
| pos_peak_in_phases_hybrid < pos_peak_in_phases && |
| (pos_peak_in_phases_hybrid < (neg_peak_in_phases + jitter_var)); |
| check_b = |
| ((neg_peak_in_phases - pos_peak_in_phases) >= min_time_diff) && |
| ((neg_peak_in_phases - pos_peak_in_phases) < max_time_diff) && |
| pos_peak_in_phases_hybrid < neg_peak_in_phases && |
| (pos_peak_in_phases_hybrid < (pos_peak_in_phases + jitter_var)); |
| |
| if (pos_peak_in_phases > neg_peak_in_phases && check_a) |
| detect = 2; |
| else if ((neg_peak_in_phases > pos_peak_in_phases) && check_b) |
| detect = 1; |
| |
| if (pos_peak > noise_margin && neg_peak > noise_margin && |
| gain_idx >= 0) { |
| if (detect == 1 || detect == 2) |
| fault = true; |
| } |
| |
| if (!fault) |
| detect = 0; |
| |
| ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A, |
| lan87xx_cable_test_report_trans(detect)); |
| |
| return 0; |
| } |
| |
| static int lan87xx_cable_test_get_status(struct phy_device *phydev, |
| bool *finished) |
| { |
| int rc = 0; |
| |
| *finished = false; |
| |
| /* check if cable diag was finished */ |
| rc = access_ereg(phydev, PHYACC_ATTR_MODE_READ, PHYACC_ATTR_BANK_DSP, |
| 90, 0); |
| if (rc < 0) |
| return rc; |
| |
| if ((rc & 2) == 2) { |
| /* stop cable diag*/ |
| rc = access_ereg(phydev, PHYACC_ATTR_MODE_WRITE, |
| PHYACC_ATTR_BANK_DSP, |
| 90, 0); |
| if (rc < 0) |
| return rc; |
| |
| *finished = true; |
| |
| return lan87xx_cable_test_report(phydev); |
| } |
| |
| return 0; |
| } |
| |
| static int lan87xx_read_status(struct phy_device *phydev) |
| { |
| int rc = 0; |
| |
| rc = phy_read(phydev, T1_MODE_STAT_REG); |
| if (rc < 0) |
| return rc; |
| |
| if (rc & T1_LINK_UP_MSK) |
| phydev->link = 1; |
| else |
| phydev->link = 0; |
| |
| phydev->speed = SPEED_UNKNOWN; |
| phydev->duplex = DUPLEX_UNKNOWN; |
| phydev->pause = 0; |
| phydev->asym_pause = 0; |
| |
| rc = genphy_read_master_slave(phydev); |
| if (rc < 0) |
| return rc; |
| |
| rc = genphy_read_status_fixed(phydev); |
| if (rc < 0) |
| return rc; |
| |
| return rc; |
| } |
| |
| static int lan87xx_config_aneg(struct phy_device *phydev) |
| { |
| u16 ctl = 0; |
| |
| switch (phydev->master_slave_set) { |
| case MASTER_SLAVE_CFG_MASTER_FORCE: |
| ctl |= CTL1000_AS_MASTER; |
| break; |
| case MASTER_SLAVE_CFG_SLAVE_FORCE: |
| break; |
| case MASTER_SLAVE_CFG_UNKNOWN: |
| case MASTER_SLAVE_CFG_UNSUPPORTED: |
| return 0; |
| default: |
| phydev_warn(phydev, "Unsupported Master/Slave mode\n"); |
| return -EOPNOTSUPP; |
| } |
| |
| return phy_modify_changed(phydev, MII_CTRL1000, CTL1000_AS_MASTER, ctl); |
| } |
| |
| static struct phy_driver microchip_t1_phy_driver[] = { |
| { |
| PHY_ID_MATCH_MODEL(PHY_ID_LAN87XX), |
| .name = "Microchip LAN87xx T1", |
| .flags = PHY_POLL_CABLE_TEST, |
| .features = PHY_BASIC_T1_FEATURES, |
| .config_init = lan87xx_config_init, |
| .config_intr = lan87xx_phy_config_intr, |
| .handle_interrupt = lan87xx_handle_interrupt, |
| .suspend = genphy_suspend, |
| .resume = genphy_resume, |
| .config_aneg = lan87xx_config_aneg, |
| .read_status = lan87xx_read_status, |
| .cable_test_start = lan87xx_cable_test_start, |
| .cable_test_get_status = lan87xx_cable_test_get_status, |
| }, |
| { |
| PHY_ID_MATCH_MODEL(PHY_ID_LAN937X), |
| .name = "Microchip LAN937x T1", |
| .features = PHY_BASIC_T1_FEATURES, |
| .config_init = lan87xx_config_init, |
| .suspend = genphy_suspend, |
| .resume = genphy_resume, |
| .config_aneg = lan87xx_config_aneg, |
| .read_status = lan87xx_read_status, |
| .cable_test_start = lan87xx_cable_test_start, |
| .cable_test_get_status = lan87xx_cable_test_get_status, |
| } |
| }; |
| |
| module_phy_driver(microchip_t1_phy_driver); |
| |
| static struct mdio_device_id __maybe_unused microchip_t1_tbl[] = { |
| { PHY_ID_MATCH_MODEL(PHY_ID_LAN87XX) }, |
| { PHY_ID_MATCH_MODEL(PHY_ID_LAN937X) }, |
| { } |
| }; |
| |
| MODULE_DEVICE_TABLE(mdio, microchip_t1_tbl); |
| |
| MODULE_AUTHOR(DRIVER_AUTHOR); |
| MODULE_DESCRIPTION(DRIVER_DESC); |
| MODULE_LICENSE("GPL"); |