blob: 3368b3bd8ef2f0b648b239a8ec7d948d4d795bd6 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
# Copyright (c) 2022 Amarulasolutions
%YAML 1.2
---
$id: http://devicetree.org/schemas/media/i2c/ovti,ov5693.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Omnivision OV5693/OV5695 CMOS Sensors
maintainers:
- Tommaso Merciai <tomm.merciai@gmail.com>
description: |
The Omnivision OV5693/OV5695 are high performance, 1/4-inch, 5 megapixel, CMOS
image sensors that deliver 2592x1944 at 30fps. It provides full-frame,
sub-sampled, and windowed 10-bit MIPI images in various formats via the
Serial Camera Control Bus (SCCB) interface.
OV5693/OV5695 are controlled via I2C and two-wire Serial Camera Control Bus
(SCCB). The sensor output is available via CSI-2 serial data output (up to
2-lane).
allOf:
- $ref: /schemas/media/video-interface-devices.yaml#
- if:
properties:
compatible:
contains:
const: ovti,ov5693
then:
properties:
port:
properties:
endpoint:
required:
- link-frequencies
properties:
compatible:
enum:
- ovti,ov5693
- ovti,ov5695
reg:
maxItems: 1
clocks:
description:
System input clock (aka XVCLK). From 6 to 27 MHz.
maxItems: 1
clock-names:
const: xvclk
dovdd-supply:
description:
Digital I/O voltage supply, 1.8V.
avdd-supply:
description:
Analog voltage supply, 2.8V.
dvdd-supply:
description:
Digital core voltage supply, 1.2V.
reset-gpios:
description:
The phandle and specifier for the GPIO that controls sensor reset.
This corresponds to the hardware pin XSHUTDN which is physically
active low.
maxItems: 1
port:
description: MIPI CSI-2 transmitter port
$ref: /schemas/graph.yaml#/$defs/port-base
additionalProperties: false
properties:
endpoint:
$ref: /schemas/media/video-interfaces.yaml#
unevaluatedProperties: false
properties:
link-frequencies: true
data-lanes:
minItems: 1
maxItems: 2
required:
- data-lanes
required:
- compatible
- reg
- clocks
- port
unevaluatedProperties: false
examples:
- |
#include <dt-bindings/clock/px30-cru.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/rockchip.h>
i2c {
#address-cells = <1>;
#size-cells = <0>;
ov5693: camera@36 {
compatible = "ovti,ov5693";
reg = <0x36>;
reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&cif_clkout_m0>;
clocks = <&cru SCLK_CIF_OUT>;
assigned-clocks = <&cru SCLK_CIF_OUT>;
assigned-clock-rates = <19200000>;
avdd-supply = <&vcc_1v8>;
dvdd-supply = <&vcc_1v2>;
dovdd-supply = <&vcc_2v8>;
rotation = <90>;
orientation = <0>;
port {
ucam_out: endpoint {
remote-endpoint = <&mipi_in_ucam>;
data-lanes = <1 2>;
link-frequencies = /bits/ 64 <450000000>;
};
};
};
};
...