| .. SPDX-License-Identifier: GPL-2.0 |
| |
| =============== |
| The bttv driver |
| =============== |
| |
| Release notes for bttv |
| ---------------------- |
| |
| You'll need at least these config options for bttv:: |
| |
| ./scripts/config -e PCI |
| ./scripts/config -m I2C |
| ./scripts/config -m INPUT |
| ./scripts/config -m MEDIA_SUPPORT |
| ./scripts/config -e MEDIA_PCI_SUPPORT |
| ./scripts/config -e MEDIA_ANALOG_TV_SUPPORT |
| ./scripts/config -e MEDIA_DIGITAL_TV_SUPPORT |
| ./scripts/config -e MEDIA_RADIO_SUPPORT |
| ./scripts/config -e RC_CORE |
| ./scripts/config -m VIDEO_BT848 |
| |
| If your board has digital TV, you'll also need:: |
| |
| ./scripts/config -m DVB_BT8XX |
| |
| In this case, please see :doc:`bt8xx` for additional notes. |
| |
| Make bttv work with your card |
| ----------------------------- |
| |
| If you have bttv compiled and installed, just booting the Kernel |
| should be enough for it to try probing it. However, depending |
| on the model, the Kernel may require additional information about |
| the hardware, as the device may not be able to provide such info |
| directly to the Kernel. |
| |
| If it doesn't bttv likely could not autodetect your card and needs some |
| insmod options. The most important insmod option for bttv is "card=n" |
| to select the correct card type. If you get video but no sound you've |
| very likely specified the wrong (or no) card type. A list of supported |
| cards is in :doc:`bttv-cardlist`. |
| |
| If bttv takes very long to load (happens sometimes with the cheap |
| cards which have no tuner), try adding this to your modules configuration |
| file (usually, it is either ``/etc/modules.conf`` or some file at |
| ``/etc/modules-load.d/``, but the actual place depends on your |
| distribution):: |
| |
| options i2c-algo-bit bit_test=1 |
| |
| Some cards may require an extra firmware file to work. For example, |
| for the WinTV/PVR you need one firmware file from its driver CD, |
| called: ``hcwamc.rbf``. It is inside a self-extracting zip file |
| called ``pvr45xxx.exe``. Just placing it at the ``/etc/firmware`` |
| directory should be enough for it to be autoload during the driver's |
| probing mode (e. g. when the Kernel boots or when the driver is |
| manually loaded via ``modprobe`` command). |
| |
| If your card isn't listed in :doc:`bttv-cardlist` or if you have |
| trouble making audio work, please read :ref:`still_doesnt_work`. |
| |
| |
| Autodetecting cards |
| ------------------- |
| |
| bttv uses the PCI Subsystem ID to autodetect the card type. lspci lists |
| the Subsystem ID in the second line, looks like this: |
| |
| .. code-block:: none |
| |
| 00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02) |
| Subsystem: Hauppauge computer works Inc. WinTV/GO |
| Flags: bus master, medium devsel, latency 32, IRQ 5 |
| Memory at e2000000 (32-bit, prefetchable) [size=4K] |
| |
| only bt878-based cards can have a subsystem ID (which does not mean |
| that every card really has one). bt848 cards can't have a Subsystem |
| ID and therefore can't be autodetected. There is a list with the ID's |
| at :doc:`bttv-cardlist` (in case you are interested or want to mail |
| patches with updates). |
| |
| |
| .. _still_doesnt_work: |
| |
| Still doesn't work? |
| ------------------- |
| |
| I do NOT have a lab with 30+ different grabber boards and a |
| PAL/NTSC/SECAM test signal generator at home, so I often can't |
| reproduce your problems. This makes debugging very difficult for me. |
| |
| If you have some knowledge and spare time, please try to fix this |
| yourself (patches very welcome of course...) You know: The linux |
| slogan is "Do it yourself". |
| |
| There is a mailing list at |
| http://vger.kernel.org/vger-lists.html#linux-media |
| |
| If you have trouble with some specific TV card, try to ask there |
| instead of mailing me directly. The chance that someone with the |
| same card listens there is much higher... |
| |
| For problems with sound: There are a lot of different systems used |
| for TV sound all over the world. And there are also different chips |
| which decode the audio signal. Reports about sound problems ("stereo |
| doesn't work") are pretty useless unless you include some details |
| about your hardware and the TV sound scheme used in your country (or |
| at least the country you are living in). |
| |
| Modprobe options |
| ---------------- |
| |
| .. note:: |
| |
| |
| The following argument list can be outdated, as we might add more |
| options if ever needed. In case of doubt, please check with |
| ``modinfo <module>``. |
| |
| This command prints various information about a kernel |
| module, among them a complete and up-to-date list of insmod options. |
| |
| |
| |
| bttv |
| The bt848/878 (grabber chip) driver |
| |
| insmod args:: |
| |
| card=n card type, see CARDLIST for a list. |
| tuner=n tuner type, see CARDLIST for a list. |
| radio=0/1 card supports radio |
| pll=0/1/2 pll settings |
| |
| 0: don't use PLL |
| 1: 28 MHz crystal installed |
| 2: 35 MHz crystal installed |
| |
| triton1=0/1 for Triton1 (+others) compatibility |
| vsfx=0/1 yet another chipset bug compatibility bit |
| see README.quirks for details on these two. |
| |
| bigendian=n Set the endianness of the gfx framebuffer. |
| Default is native endian. |
| fieldnr=0/1 Count fields. Some TV descrambling software |
| needs this, for others it only generates |
| 50 useless IRQs/sec. default is 0 (off). |
| autoload=0/1 autoload helper modules (tuner, audio). |
| default is 1 (on). |
| bttv_verbose=0/1/2 verbose level (at insmod time, while |
| looking at the hardware). default is 1. |
| bttv_debug=0/1 debug messages (for capture). |
| default is 0 (off). |
| irq_debug=0/1 irq handler debug messages. |
| default is 0 (off). |
| gbuffers=2-32 number of capture buffers for mmap'ed capture. |
| default is 4. |
| gbufsize= size of capture buffers. default and |
| maximum value is 0x208000 (~2MB) |
| no_overlay=0 Enable overlay on broken hardware. There |
| are some chipsets (SIS for example) which |
| are known to have problems with the PCI DMA |
| push used by bttv. bttv will disable overlay |
| by default on this hardware to avoid crashes. |
| With this insmod option you can override this. |
| no_overlay=1 Disable overlay. It should be used by broken |
| hardware that doesn't support PCI2PCI direct |
| transfers. |
| automute=0/1 Automatically mutes the sound if there is |
| no TV signal, on by default. You might try |
| to disable this if you have bad input signal |
| quality which leading to unwanted sound |
| dropouts. |
| chroma_agc=0/1 AGC of chroma signal, off by default. |
| adc_crush=0/1 Luminance ADC crush, on by default. |
| i2c_udelay= Allow reduce I2C speed. Default is 5 usecs |
| (meaning 66,67 Kbps). The default is the |
| maximum supported speed by kernel bitbang |
| algorithm. You may use lower numbers, if I2C |
| messages are lost (16 is known to work on |
| all supported cards). |
| |
| bttv_gpio=0/1 |
| gpiomask= |
| audioall= |
| audiomux= |
| See Sound-FAQ for a detailed description. |
| |
| remap, card, radio and pll accept up to four comma-separated arguments |
| (for multiple boards). |
| |
| tuner |
| The tuner driver. You need this unless you want to use only |
| with a camera or the board doesn't provide analog TV tuning. |
| |
| insmod args:: |
| |
| debug=1 print some debug info to the syslog |
| type=n type of the tuner chip. n as follows: |
| see CARDLIST for a complete list. |
| pal=[bdgil] select PAL variant (used for some tuners |
| only, important for the audio carrier). |
| |
| tvaudio |
| Provide a single driver for all simple i2c audio control |
| chips (tda/tea*). |
| |
| insmod args:: |
| |
| tda8425 = 1 enable/disable the support for the |
| tda9840 = 1 various chips. |
| tda9850 = 1 The tea6300 can't be autodetected and is |
| tda9855 = 1 therefore off by default, if you have |
| tda9873 = 1 this one on your card (STB uses these) |
| tda9874a = 1 you have to enable it explicitly. |
| tea6300 = 0 The two tda985x chips use the same i2c |
| tea6420 = 1 address and can't be disturgished from |
| pic16c54 = 1 each other, you might have to disable |
| the wrong one. |
| debug = 1 print debug messages |
| |
| msp3400 |
| The driver for the msp34xx sound processor chips. If you have a |
| stereo card, you probably want to insmod this one. |
| |
| insmod args:: |
| |
| debug=1/2 print some debug info to the syslog, |
| 2 is more verbose. |
| simple=1 Use the "short programming" method. Newer |
| msp34xx versions support this. You need this |
| for dbx stereo. Default is on if supported by |
| the chip. |
| once=1 Don't check the TV-stations Audio mode |
| every few seconds, but only once after |
| channel switches. |
| amsound=1 Audio carrier is AM/NICAM at 6.5 Mhz. This |
| should improve things for french people, the |
| carrier autoscan seems to work with FM only... |
| |
| If the box freezes hard with bttv |
| --------------------------------- |
| |
| It might be a bttv driver bug. It also might be bad hardware. It also |
| might be something else ... |
| |
| Just mailing me "bttv freezes" isn't going to help much. This README |
| has a few hints how you can help to pin down the problem. |
| |
| |
| bttv bugs |
| ~~~~~~~~~ |
| |
| If some version works and another doesn't it is likely to be a driver |
| bug. It is very helpful if you can tell where exactly it broke |
| (i.e. the last working and the first broken version). |
| |
| With a hard freeze you probably doesn't find anything in the logfiles. |
| The only way to capture any kernel messages is to hook up a serial |
| console and let some terminal application log the messages. /me uses |
| screen. See :doc:`/admin-guide/serial-console` for details on setting |
| up a serial console. |
| |
| Read :doc:`/admin-guide/bug-hunting` to learn how to get any useful |
| information out of a register+stack dump printed by the kernel on |
| protection faults (so-called "kernel oops"). |
| |
| If you run into some kind of deadlock, you can try to dump a call trace |
| for each process using sysrq-t (see :doc:`/admin-guide/sysrq`). |
| This way it is possible to figure where *exactly* some process in "D" |
| state is stuck. |
| |
| I've seen reports that bttv 0.7.x crashes whereas 0.8.x works rock solid |
| for some people. Thus probably a small buglet left somewhere in bttv |
| 0.7.x. I have no idea where exactly, it works stable for me and a lot of |
| other people. But in case you have problems with the 0.7.x versions you |
| can give 0.8.x a try ... |
| |
| |
| hardware bugs |
| ~~~~~~~~~~~~~ |
| |
| Some hardware can't deal with PCI-PCI transfers (i.e. grabber => vga). |
| Sometimes problems show up with bttv just because of the high load on |
| the PCI bus. The bt848/878 chips have a few workarounds for known |
| incompatibilities, see README.quirks. |
| |
| Some folks report that increasing the pci latency helps too, |
| althrought I'm not sure whenever this really fixes the problems or |
| only makes it less likely to happen. Both bttv and btaudio have a |
| insmod option to set the PCI latency of the device. |
| |
| Some mainboard have problems to deal correctly with multiple devices |
| doing DMA at the same time. bttv + ide seems to cause this sometimes, |
| if this is the case you likely see freezes only with video and hard disk |
| access at the same time. Updating the IDE driver to get the latest and |
| greatest workarounds for hardware bugs might fix these problems. |
| |
| |
| other |
| ~~~~~ |
| |
| If you use some binary-only yunk (like nvidia module) try to reproduce |
| the problem without. |
| |
| IRQ sharing is known to cause problems in some cases. It works just |
| fine in theory and many configurations. Neverless it might be worth a |
| try to shuffle around the PCI cards to give bttv another IRQ or make |
| it share the IRQ with some other piece of hardware. IRQ sharing with |
| VGA cards seems to cause trouble sometimes. I've also seen funny |
| effects with bttv sharing the IRQ with the ACPI bridge (and |
| apci-enabled kernel). |
| |
| Bttv quirks |
| ----------- |
| |
| Below is what the bt878 data book says about the PCI bug compatibility |
| modes of the bt878 chip. |
| |
| The triton1 insmod option sets the EN_TBFX bit in the control register. |
| The vsfx insmod option does the same for EN_VSFX bit. If you have |
| stability problems you can try if one of these options makes your box |
| work solid. |
| |
| drivers/pci/quirks.c knows about these issues, this way these bits are |
| enabled automagically for known-buggy chipsets (look at the kernel |
| messages, bttv tells you). |
| |
| Normal PCI Mode |
| ~~~~~~~~~~~~~~~ |
| |
| The PCI REQ signal is the logical-or of the incoming function requests. |
| The inter-nal GNT[0:1] signals are gated asynchronously with GNT and |
| demultiplexed by the audio request signal. Thus the arbiter defaults to |
| the video function at power-up and parks there during no requests for |
| bus access. This is desirable since the video will request the bus more |
| often. However, the audio will have highest bus access priority. Thus |
| the audio will have first access to the bus even when issuing a request |
| after the video request but before the PCI external arbiter has granted |
| access to the Bt879. Neither function can preempt the other once on the |
| bus. The duration to empty the entire video PCI FIFO onto the PCI bus is |
| very short compared to the bus access latency the audio PCI FIFO can |
| tolerate. |
| |
| |
| 430FX Compatibility Mode |
| ~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| When using the 430FX PCI, the following rules will ensure |
| compatibility: |
| |
| (1) Deassert REQ at the same time as asserting FRAME. |
| (2) Do not reassert REQ to request another bus transaction until after |
| finish-ing the previous transaction. |
| |
| Since the individual bus masters do not have direct control of REQ, a |
| simple logical-or of video and audio requests would violate the rules. |
| Thus, both the arbiter and the initiator contain 430FX compatibility |
| mode logic. To enable 430FX mode, set the EN_TBFX bit as indicated in |
| Device Control Register on page 104. |
| |
| When EN_TBFX is enabled, the arbiter ensures that the two compatibility |
| rules are satisfied. Before GNT is asserted by the PCI arbiter, this |
| internal arbiter may still logical-or the two requests. However, once |
| the GNT is issued, this arbiter must lock in its decision and now route |
| only the granted request to the REQ pin. The arbiter decision lock |
| happens regardless of the state of FRAME because it does not know when |
| FRAME will be asserted (typically - each initiator will assert FRAME on |
| the cycle following GNT). When FRAME is asserted, it is the initiator s |
| responsibility to remove its request at the same time. It is the |
| arbiters responsibility to allow this request to flow through to REQ and |
| not allow the other request to hold REQ asserted. The decision lock may |
| be removed at the end of the transaction: for example, when the bus is |
| idle (FRAME and IRDY). The arbiter decision may then continue |
| asynchronously until GNT is again asserted. |
| |
| |
| Interfacing with Non-PCI 2.1 Compliant Core Logic |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| A small percentage of core logic devices may start a bus transaction |
| during the same cycle that GNT is de-asserted. This is non PCI 2.1 |
| compliant. To ensure compatibility when using PCs with these PCI |
| controllers, the EN_VSFX bit must be enabled (refer to Device Control |
| Register on page 104). When in this mode, the arbiter does not pass GNT |
| to the internal functions unless REQ is asserted. This prevents a bus |
| transaction from starting the same cycle as GNT is de-asserted. This |
| also has the side effect of not being able to take advantage of bus |
| parking, thus lowering arbitration performance. The Bt879 drivers must |
| query for these non-compliant devices, and set the EN_VSFX bit only if |
| required. |
| |
| |
| Other elements of the tvcards array |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| If you are trying to make a new card work you might find it useful to |
| know what the other elements in the tvcards array are good for:: |
| |
| video_inputs - # of video inputs the card has |
| audio_inputs - historical cruft, not used any more. |
| tuner - which input is the tuner |
| svhs - which input is svhs (all others are labeled composite) |
| muxsel - video mux, input->registervalue mapping |
| pll - same as pll= insmod option |
| tuner_type - same as tuner= insmod option |
| *_modulename - hint whenever some card needs this or that audio |
| module loaded to work properly. |
| has_radio - whenever this TV card has a radio tuner. |
| no_msp34xx - "1" disables loading of msp3400.o module |
| no_tda9875 - "1" disables loading of tda9875.o module |
| needs_tvaudio - set to "1" to load tvaudio.o module |
| |
| If some config item is specified both from the tvcards array and as |
| insmod option, the insmod option takes precedence. |
| |
| Cards |
| ----- |
| |
| .. note:: |
| |
| For a more updated list, please check |
| https://linuxtv.org/wiki/index.php/Hardware_Device_Information |
| |
| Supported cards: Bt848/Bt848a/Bt849/Bt878/Bt879 cards |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| All cards with Bt848/Bt848a/Bt849/Bt878/Bt879 and normal |
| Composite/S-VHS inputs are supported. Teletext and Intercast support |
| (PAL only) for ALL cards via VBI sample decoding in software. |
| |
| Some cards with additional multiplexing of inputs or other additional |
| fancy chips are only partially supported (unless specifications by the |
| card manufacturer are given). When a card is listed here it isn't |
| necessarily fully supported. |
| |
| All other cards only differ by additional components as tuners, sound |
| decoders, EEPROMs, teletext decoders ... |
| |
| |
| MATRIX Vision |
| ~~~~~~~~~~~~~ |
| |
| MV-Delta |
| - Bt848A |
| - 4 Composite inputs, 1 S-VHS input (shared with 4th composite) |
| - EEPROM |
| |
| http://www.matrix-vision.de/ |
| |
| This card has no tuner but supports all 4 composite (1 shared with an |
| S-VHS input) of the Bt848A. |
| Very nice card if you only have satellite TV but several tuners connected |
| to the card via composite. |
| |
| Many thanks to Matrix-Vision for giving us 2 cards for free which made |
| Bt848a/Bt849 single crystal operation support possible!!! |
| |
| |
| |
| Miro/Pinnacle PCTV |
| ~~~~~~~~~~~~~~~~~~ |
| |
| - Bt848 |
| some (all??) come with 2 crystals for PAL/SECAM and NTSC |
| - PAL, SECAM or NTSC TV tuner (Philips or TEMIC) |
| - MSP34xx sound decoder on add on board |
| decoder is supported but AFAIK does not yet work |
| (other sound MUX setting in GPIO port needed??? somebody who fixed this???) |
| - 1 tuner, 1 composite and 1 S-VHS input |
| - tuner type is autodetected |
| |
| http://www.miro.de/ |
| http://www.miro.com/ |
| |
| |
| Many thanks for the free card which made first NTSC support possible back |
| in 1997! |
| |
| |
| Hauppauge Win/TV pci |
| ~~~~~~~~~~~~~~~~~~~~ |
| |
| There are many different versions of the Hauppauge cards with different |
| tuners (TV+Radio ...), teletext decoders. |
| Note that even cards with same model numbers have (depending on the revision) |
| different chips on it. |
| |
| - Bt848 (and others but always in 2 crystal operation???) |
| newer cards have a Bt878 |
| |
| - PAL, SECAM, NTSC or tuner with or without Radio support |
| |
| e.g.: |
| |
| - PAL: |
| |
| - TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners |
| - TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3 |
| |
| - NTSC: |
| |
| - TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners |
| - TSA5518: no datasheet available on Philips site |
| |
| - Philips SAA5246 or SAA5284 ( or no) Teletext decoder chip |
| with buffer RAM (e.g. Winbond W24257AS-35: 32Kx8 CMOS static RAM) |
| SAA5246 (I2C 0x22) is supported |
| |
| - 256 bytes EEPROM: Microchip 24LC02B or Philips 8582E2Y |
| with configuration information |
| I2C address 0xa0 (24LC02B also responds to 0xa2-0xaf) |
| |
| - 1 tuner, 1 composite and (depending on model) 1 S-VHS input |
| |
| - 14052B: mux for selection of sound source |
| |
| - sound decoder: TDA9800, MSP34xx (stereo cards) |
| |
| |
| Askey CPH-Series |
| ~~~~~~~~~~~~~~~~ |
| Developed by TelSignal(?), OEMed by many vendors (Typhoon, Anubis, Dynalink) |
| |
| - Card series: |
| - CPH01x: BT848 capture only |
| - CPH03x: BT848 |
| - CPH05x: BT878 with FM |
| - CPH06x: BT878 (w/o FM) |
| - CPH07x: BT878 capture only |
| |
| - TV standards: |
| - CPH0x0: NTSC-M/M |
| - CPH0x1: PAL-B/G |
| - CPH0x2: PAL-I/I |
| - CPH0x3: PAL-D/K |
| - CPH0x4: SECAM-L/L |
| - CPH0x5: SECAM-B/G |
| - CPH0x6: SECAM-D/K |
| - CPH0x7: PAL-N/N |
| - CPH0x8: PAL-B/H |
| - CPH0x9: PAL-M/M |
| |
| - CPH03x was often sold as "TV capturer". |
| |
| Identifying: |
| |
| #) 878 cards can be identified by PCI Subsystem-ID: |
| - 144f:3000 = CPH06x |
| - 144F:3002 = CPH05x w/ FM |
| - 144F:3005 = CPH06x_LC (w/o remote control) |
| #) The cards have a sticker with "CPH"-model on the back. |
| #) These cards have a number printed on the PCB just above the tuner metal box: |
| - "80-CP2000300-x" = CPH03X |
| - "80-CP2000500-x" = CPH05X |
| - "80-CP2000600-x" = CPH06X / CPH06x_LC |
| |
| Askey sells these cards as "Magic TView series", Brand "MagicXpress". |
| Other OEM often call these "Tview", "TView99" or else. |
| |
| Lifeview Flyvideo Series: |
| ~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| The naming of these series differs in time and space. |
| |
| Identifying: |
| #) Some models can be identified by PCI subsystem ID: |
| |
| - 1852:1852 = Flyvideo 98 FM |
| - 1851:1850 = Flyvideo 98 |
| - 1851:1851 = Flyvideo 98 EZ (capture only) |
| |
| #) There is a print on the PCB: |
| |
| - LR25 = Flyvideo (Zoran ZR36120, SAA7110A) |
| - LR26 Rev.N = Flyvideo II (Bt848) |
| - LR26 Rev.O = Flyvideo II (Bt878) |
| - LR37 Rev.C = Flyvideo EZ (Capture only, ZR36120 + SAA7110) |
| - LR38 Rev.A1= Flyvideo II EZ (Bt848 capture only) |
| - LR50 Rev.Q = Flyvideo 98 (w/eeprom and PCI subsystem ID) |
| - LR50 Rev.W = Flyvideo 98 (no eeprom) |
| - LR51 Rev.E = Flyvideo 98 EZ (capture only) |
| - LR90 = Flyvideo 2000 (Bt878) |
| - LR90 Flyvideo 2000S (Bt878) w/Stereo TV (Package incl. LR91 daughterboard) |
| - LR91 = Stereo daughter card for LR90 |
| - LR97 = Flyvideo DVBS |
| - LR99 Rev.E = Low profile card for OEM integration (only internal audio!) bt878 |
| - LR136 = Flyvideo 2100/3100 (Low profile, SAA7130/SAA7134) |
| - LR137 = Flyvideo DV2000/DV3000 (SAA7130/SAA7134 + IEEE1394) |
| - LR138 Rev.C= Flyvideo 2000 (SAA7130) |
| - LR138 Flyvideo 3000 (SAA7134) w/Stereo TV |
| |
| - These exist in variations w/FM and w/Remote sometimes denoted |
| by suffixes "FM" and "R". |
| |
| #) You have a laptop (miniPCI card): |
| |
| - Product = FlyTV Platinum Mini |
| - Model/Chip = LR212/saa7135 |
| |
| - Lifeview.com.tw states (Feb. 2002): |
| "The FlyVideo2000 and FlyVideo2000s product name have renamed to FlyVideo98." |
| Their Bt8x8 cards are listed as discontinued. |
| - Flyvideo 2000S was probably sold as Flyvideo 3000 in some countries(Europe?). |
| The new Flyvideo 2000/3000 are SAA7130/SAA7134 based. |
| |
| "Flyvideo II" had been the name for the 848 cards, nowadays (in Germany) |
| this name is re-used for LR50 Rev.W. |
| |
| The Lifeview website mentioned Flyvideo III at some time, but such a card |
| has not yet been seen (perhaps it was the german name for LR90 [stereo]). |
| These cards are sold by many OEMs too. |
| |
| FlyVideo A2 (Elta 8680)= LR90 Rev.F (w/Remote, w/o FM, stereo TV by tda9821) {Germany} |
| |
| Lifeview 3000 (Elta 8681) as sold by Plus(April 2002), Germany = LR138 w/ saa7134 |
| |
| lifeview config coding on gpio pins 0-9 |
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ |
| |
| - LR50 rev. Q ("PARTS: 7031505116), Tuner wurde als Nr. 5 erkannt, Eingänge |
| SVideo, TV, Composite, Audio, Remote: |
| |
| - CP9..1=100001001 (1: 0-Ohm-Widerstand gegen GND unbestückt; 0: bestückt) |
| |
| |
| Typhoon TV card series: |
| ~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| These can be CPH, Flyvideo, Pixelview or KNC1 series. |
| |
| Typhoon is the brand of Anubis. |
| |
| Model 50680 got re-used, some model no. had different contents over time. |
| |
| Models: |
| |
| - 50680 "TV Tuner PCI Pal BG"(old,red package)=can be CPH03x(bt848) or CPH06x(bt878) |
| - 50680 "TV Tuner Pal BG" (blue package)= Pixelview PV-BT878P+ (Rev 9B) |
| - 50681 "TV Tuner PCI Pal I" (variant of 50680) |
| - 50682 "TView TV/FM Tuner Pal BG" = Flyvideo 98FM (LR50 Rev.Q) |
| |
| .. note:: |
| |
| The package has a picture of CPH05x (which would be a real TView) |
| |
| - 50683 "TV Tuner PCI SECAM" (variant of 50680) |
| - 50684 "TV Tuner Pal BG" = Pixelview 878TV(Rev.3D) |
| - 50686 "TV Tuner" = KNC1 TV Station |
| - 50687 "TV Tuner stereo" = KNC1 TV Station pro |
| - 50688 "TV Tuner RDS" (black package) = KNC1 TV Station RDS |
| - 50689 TV SAT DVB-S CARD CI PCI (SAA7146AH, SU1278?) = "KNC1 TV Station DVB-S" |
| - 50692 "TV/FM Tuner" (small PCB) |
| - 50694 TV TUNER CARD RDS (PHILIPS CHIPSET SAA7134HL) |
| - 50696 TV TUNER STEREO (PHILIPS CHIPSET SAA7134HL, MK3ME Tuner) |
| - 50804 PC-SAT TV/Audio Karte = Techni-PC-Sat (ZORAN 36120PQC, Tuner:Alps) |
| - 50866 TVIEW SAT RECEIVER+ADR |
| - 50868 "TV/FM Tuner Pal I" (variant of 50682) |
| - 50999 "TV/FM Tuner Secam" (variant of 50682) |
| |
| Guillemot |
| ~~~~~~~~~ |
| |
| Models: |
| |
| - Maxi-TV PCI (ZR36120) |
| - Maxi TV Video 2 = LR50 Rev.Q (FI1216MF, PAL BG+SECAM) |
| - Maxi TV Video 3 = CPH064 (PAL BG + SECAM) |
| |
| Mentor |
| ~~~~~~ |
| |
| Mentor TV card ("55-878TV-U1") = Pixelview 878TV(Rev.3F) (w/FM w/Remote) |
| |
| Prolink |
| ~~~~~~~ |
| |
| - TV cards: |
| |
| - PixelView Play TV pro - (Model: PV-BT878P+ REV 8E) |
| - PixelView Play TV pro - (Model: PV-BT878P+ REV 9D) |
| - PixelView Play TV pro - (Model: PV-BT878P+ REV 4C / 8D / 10A ) |
| - PixelView Play TV - (Model: PV-BT848P+) |
| - 878TV - (Model: PV-BT878TV) |
| |
| - Multimedia TV packages (card + software pack): |
| |
| - PixelView Play TV Theater - (Model: PV-M4200) = PixelView Play TV pro + Software |
| - PixelView Play TV PAK - (Model: PV-BT878P+ REV 4E) |
| - PixelView Play TV/VCR - (Model: PV-M3200 REV 4C / 8D / 10A ) |
| - PixelView Studio PAK - (Model: M2200 REV 4C / 8D / 10A ) |
| - PixelView PowerStudio PAK - (Model: PV-M3600 REV 4E) |
| - PixelView DigitalVCR PAK - (Model: PV-M2400 REV 4C / 8D / 10A ) |
| - PixelView PlayTV PAK II (TV/FM card + usb camera) PV-M3800 |
| - PixelView PlayTV XP PV-M4700,PV-M4700(w/FM) |
| - PixelView PlayTV DVR PV-M4600 package contents:PixelView PlayTV pro, windvr & videoMail s/w |
| |
| - Further Cards: |
| |
| - PV-BT878P+rev.9B (Play TV Pro, opt. w/FM w/NICAM) |
| - PV-BT878P+rev.2F |
| - PV-BT878P Rev.1D (bt878, capture only) |
| |
| - XCapture PV-CX881P (cx23881) |
| - PlayTV HD PV-CX881PL+, PV-CX881PL+(w/FM) (cx23881) |
| |
| - DTV3000 PV-DTV3000P+ DVB-S CI = Twinhan VP-1030 |
| - DTV2000 DVB-S = Twinhan VP-1020 |
| |
| - Video Conferencing: |
| |
| - PixelView Meeting PAK - (Model: PV-BT878P) |
| - PixelView Meeting PAK Lite - (Model: PV-BT878P) |
| - PixelView Meeting PAK plus - (Model: PV-BT878P+rev 4C/8D/10A) |
| - PixelView Capture - (Model: PV-BT848P) |
| - PixelView PlayTV USB pro |
| - Model No. PV-NT1004+, PV-NT1004+ (w/FM) = NT1004 USB decoder chip + SAA7113 video decoder chip |
| |
| Dynalink |
| ~~~~~~~~ |
| |
| These are CPH series. |
| |
| Phoebemicro |
| ~~~~~~~~~~~ |
| |
| - TV Master = CPH030 or CPH060 |
| - TV Master FM = CPH050 |
| |
| Genius/Kye |
| ~~~~~~~~~~ |
| |
| - Video Wonder/Genius Internet Video Kit = LR37 Rev.C |
| - Video Wonder Pro II (848 or 878) = LR26 |
| |
| Tekram |
| ~~~~~~ |
| |
| - VideoCap C205 (Bt848) |
| - VideoCap C210 (zr36120 +Philips) |
| - CaptureTV M200 (ISA) |
| - CaptureTV M205 (Bt848) |
| |
| Lucky Star |
| ~~~~~~~~~~ |
| |
| - Image World Conference TV = LR50 Rev. Q |
| |
| Leadtek |
| ~~~~~~~ |
| |
| - WinView 601 (Bt848) |
| - WinView 610 (Zoran) |
| - WinFast2000 |
| - WinFast2000 XP |
| |
| Support for the Leadtek WinView 601 TV/FM |
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ |
| |
| Author of this section: Jon Tombs <jon@gte.esi.us.es> |
| |
| This card is basically the same as all the rest (Bt484A, Philips tuner), |
| the main difference is that they have attached a programmable attenuator to 3 |
| GPIO lines in order to give some volume control. They have also stuck an |
| infra-red remote control decoded on the board, I will add support for this |
| when I get time (it simple generates an interrupt for each key press, with |
| the key code is placed in the GPIO port). |
| |
| I don't yet have any application to test the radio support. The tuner |
| frequency setting should work but it is possible that the audio multiplexer |
| is wrong. If it doesn't work, send me email. |
| |
| |
| - No Thanks to Leadtek they refused to answer any questions about their |
| hardware. The driver was written by visual inspection of the card. If you |
| use this driver, send an email insult to them, and tell them you won't |
| continue buying their hardware unless they support Linux. |
| |
| - Little thanks to Princeton Technology Corp (http://www.princeton.com.tw) |
| who make the audio attenuator. Their publicly available data-sheet available |
| on their web site doesn't include the chip programming information! Hidden |
| on their server are the full data-sheets, but don't ask how I found it. |
| |
| To use the driver I use the following options, the tuner and pll settings might |
| be different in your country. You can force it via modprobe parameters. |
| For example:: |
| |
| modprobe bttv tuner=1 pll=28 radio=1 card=17 |
| |
| Sets tuner type 1 (Philips PAL_I), PLL with a 28 MHz crystal, enables |
| FM radio and selects bttv card ID 17 (Leadtek WinView 601). |
| |
| |
| KNC One |
| ~~~~~~~ |
| |
| - TV-Station |
| - TV-Station SE (+Software Bundle) |
| - TV-Station pro (+TV stereo) |
| - TV-Station FM (+Radio) |
| - TV-Station RDS (+RDS) |
| - TV Station SAT (analog satellite) |
| - TV-Station DVB-S |
| |
| .. note:: newer Cards have saa7134, but model name stayed the same? |
| |
| Provideo |
| ~~~~~~~~ |
| |
| - PV951 or PV-951, now named PV-951T |
| (also are sold as: |
| Boeder TV-FM Video Capture Card, |
| Titanmedia Supervision TV-2400, |
| Provideo PV951 TF, |
| 3DeMon PV951, |
| MediaForte TV-Vision PV951, |
| Yoko PV951, |
| Vivanco Tuner Card PCI Art.-Nr.: 68404 |
| ) |
| |
| - Surveillance Series: |
| |
| - PV-141 |
| - PV-143 |
| - PV-147 |
| - PV-148 (capture only) |
| - PV-150 |
| - PV-151 |
| |
| - TV-FM Tuner Series: |
| |
| - PV-951TDV (tv tuner + 1394) |
| - PV-951T/TF |
| - PV-951PT/TF |
| - PV-956T/TF Low Profile |
| - PV-911 |
| |
| Highscreen |
| ~~~~~~~~~~ |
| |
| Models: |
| |
| - TV Karte = LR50 Rev.S |
| - TV-Boostar = Terratec Terra TV+ Version 1.0 (Bt848, tda9821) "ceb105.pcb" |
| |
| Zoltrix |
| ~~~~~~~ |
| |
| Models: |
| |
| - Face to Face Capture (Bt848 capture only) (PCB "VP-2848") |
| - Face To Face TV MAX (Bt848) (PCB "VP-8482 Rev1.3") |
| - Genie TV (Bt878) (PCB "VP-8790 Rev 2.1") |
| - Genie Wonder Pro |
| |
| AVerMedia |
| ~~~~~~~~~ |
| |
| - AVer FunTV Lite (ISA, AV3001 chipset) "M101.C" |
| - AVerTV |
| - AVerTV Stereo |
| - AVerTV Studio (w/FM) |
| - AVerMedia TV98 with Remote |
| - AVerMedia TV/FM98 Stereo |
| - AVerMedia TVCAM98 |
| - TVCapture (Bt848) |
| - TVPhone (Bt848) |
| - TVCapture98 (="AVerMedia TV98" in USA) (Bt878) |
| - TVPhone98 (Bt878, w/FM) |
| |
| ======== =========== =============== ======= ====== ======== ======================= |
| PCB PCI-ID Model-Name Eeprom Tuner Sound Country |
| ======== =========== =============== ======= ====== ======== ======================= |
| M101.C ISA ! |
| M108-B Bt848 -- FR1236 US [#f2]_, [#f3]_ |
| M1A8-A Bt848 AVer TV-Phone FM1216 -- |
| M168-T 1461:0003 AVerTV Studio 48:17 FM1216 TDA9840T D [#f1]_ w/FM w/Remote |
| M168-U 1461:0004 TVCapture98 40:11 FI1216 -- D w/Remote |
| M168II-B 1461:0003 Medion MD9592 48:16 FM1216 TDA9873H D w/FM |
| ======== =========== =============== ======= ====== ======== ======================= |
| |
| .. [#f1] Daughterboard MB68-A with TDA9820T and TDA9840T |
| .. [#f2] Sony NE41S soldered (stereo sound?) |
| .. [#f3] Daughterboard M118-A w/ pic 16c54 and 4 MHz quartz |
| |
| - US site has different drivers for (as of 09/2002): |
| |
| - EZ Capture/InterCam PCI (BT-848 chip) |
| - EZ Capture/InterCam PCI (BT-878 chip) |
| - TV-Phone (BT-848 chip) |
| - TV98 (BT-848 chip) |
| - TV98 With Remote (BT-848 chip) |
| - TV98 (BT-878 chip) |
| - TV98 With Remote (BT-878) |
| - TV/FM98 (BT-878 chip) |
| - AVerTV |
| - AverTV Stereo |
| - AVerTV Studio |
| |
| DE hat diverse Treiber fuer diese Modelle (Stand 09/2002): |
| |
| - TVPhone (848) mit Philips tuner FR12X6 (w/ FM radio) |
| - TVPhone (848) mit Philips tuner FM12X6 (w/ FM radio) |
| - TVCapture (848) w/Philips tuner FI12X6 |
| - TVCapture (848) non-Philips tuner |
| - TVCapture98 (Bt878) |
| - TVPhone98 (Bt878) |
| - AVerTV und TVCapture98 w/VCR (Bt 878) |
| - AVerTVStudio und TVPhone98 w/VCR (Bt878) |
| - AVerTV GO Serie (Kein SVideo Input) |
| - AVerTV98 (BT-878 chip) |
| - AVerTV98 mit Fernbedienung (BT-878 chip) |
| - AVerTV/FM98 (BT-878 chip) |
| |
| - VDOmate (www.averm.com.cn) = M168U ? |
| |
| Aimslab |
| ~~~~~~~ |
| |
| Models: |
| |
| - Video Highway or "Video Highway TR200" (ISA) |
| - Video Highway Xtreme (aka "VHX") (Bt848, FM w/ TEA5757) |
| |
| IXMicro (former: IMS=Integrated Micro Solutions) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - IXTV BT848 (=TurboTV) |
| - IXTV BT878 |
| - IMS TurboTV (Bt848) |
| |
| Lifetec/Medion/Tevion/Aldi |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - LT9306/MD9306 = CPH061 |
| - LT9415/MD9415 = LR90 Rev.F or Rev.G |
| - MD9592 = Avermedia TVphone98 (PCI_ID=1461:0003), PCB-Rev=M168II-B (w/TDA9873H) |
| - MD9717 = KNC One (Rev D4, saa7134, FM1216 MK2 tuner) |
| - MD5044 = KNC One (Rev D4, saa7134, FM1216ME MK3 tuner) |
| |
| Modular Technologies (www.modulartech.com) UK |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - MM100 PCTV (Bt848) |
| - MM201 PCTV (Bt878, Bt832) w/ Quartzsight camera |
| - MM202 PCTV (Bt878, Bt832, tda9874) |
| - MM205 PCTV (Bt878) |
| - MM210 PCTV (Bt878) (Galaxy TV, Galaxymedia ?) |
| |
| Terratec |
| ~~~~~~~~ |
| |
| Models: |
| |
| - Terra TV+ Version 1.0 (Bt848), "ceb105.PCB" printed on the PCB, TDA9821 |
| - Terra TV+ Version 1.1 (Bt878), "LR74 Rev.E" printed on the PCB, TDA9821 |
| - Terra TValueRadio, "LR102 Rev.C" printed on the PCB |
| - Terra TV/Radio+ Version 1.0, "80-CP2830100-0" TTTV3 printed on the PCB, |
| "CPH010-E83" on the back, SAA6588T, TDA9873H |
| - Terra TValue Version BT878, "80-CP2830110-0 TTTV4" printed on the PCB, |
| "CPH011-D83" on back |
| - Terra TValue Version 1.0 "ceb105.PCB" (really identical to Terra TV+ Version 1.0) |
| - Terra TValue New Revision "LR102 Rec.C" |
| - Terra Active Radio Upgrade (tea5757h, saa6588t) |
| |
| - LR74 is a newer PCB revision of ceb105 (both incl. connector for Active Radio Upgrade) |
| |
| - Cinergy 400 (saa7134), "E877 11(S)", "PM820092D" printed on PCB |
| - Cinergy 600 (saa7134) |
| |
| Technisat |
| ~~~~~~~~~ |
| |
| Models: |
| |
| - Discos ADR PC-Karte ISA (no TV!) |
| - Discos ADR PC-Karte PCI (probably no TV?) |
| - Techni-PC-Sat (Sat. analog) |
| Rev 1.2 (zr36120, vpx3220, stv0030, saa5246, BSJE3-494A) |
| - Mediafocus I (zr36120/zr36125, drp3510, Sat. analog + ADR Radio) |
| - Mediafocus II (saa7146, Sat. analog) |
| - SatADR Rev 2.1 (saa7146a, saa7113h, stv0056a, msp3400c, drp3510a, BSKE3-307A) |
| - SkyStar 1 DVB (AV7110) = Technotrend Premium |
| - SkyStar 2 DVB (B2C2) (=Sky2PC) |
| |
| Siemens |
| ~~~~~~~ |
| |
| Multimedia eXtension Board (MXB) (SAA7146, SAA7111) |
| |
| Powercolor |
| ~~~~~~~~~~ |
| |
| Models: |
| |
| - MTV878 |
| Package comes with different contents: |
| |
| a) pcb "MTV878" (CARD=75) |
| b) Pixelview Rev. 4\_ |
| |
| - MTV878R w/Remote Control |
| - MTV878F w/Remote Control w/FM radio |
| |
| Pinnacle |
| ~~~~~~~~ |
| |
| PCTV models: |
| |
| - Mirovideo PCTV (Bt848) |
| - Mirovideo PCTV SE (Bt848) |
| - Mirovideo PCTV Pro (Bt848 + Daughterboard for TV Stereo and FM) |
| - Studio PCTV Rave (Bt848 Version = Mirovideo PCTV) |
| - Studio PCTV Rave (Bt878 package w/o infrared) |
| - Studio PCTV (Bt878) |
| - Studio PCTV Pro (Bt878 stereo w/ FM) |
| - Pinnacle PCTV (Bt878, MT2032) |
| - Pinnacle PCTV Pro (Bt878, MT2032) |
| - Pinncale PCTV Sat (bt878a, HM1821/1221) ["Conexant CX24110 with CX24108 tuner, aka HM1221/HM1811"] |
| - Pinnacle PCTV Sat XE |
| |
| M(J)PEG capture and playback models: |
| |
| - DC1+ (ISA) |
| - DC10 (zr36057, zr36060, saa7110, adv7176) |
| - DC10+ (zr36067, zr36060, saa7110, adv7176) |
| - DC20 (ql16x24b,zr36050, zr36016, saa7110, saa7187 ...) |
| - DC30 (zr36057, zr36050, zr36016, vpx3220, adv7176, ad1843, tea6415, miro FST97A1) |
| - DC30+ (zr36067, zr36050, zr36016, vpx3220, adv7176) |
| - DC50 (zr36067, zr36050, zr36016, saa7112, adv7176 (2 pcs.?), ad1843, miro FST97A1, Lattice ???) |
| |
| Lenco |
| ~~~~~ |
| |
| Models: |
| |
| - MXR-9565 (=Technisat Mediafocus?) |
| - MXR-9571 (Bt848) (=CPH031?) |
| - MXR-9575 |
| - MXR-9577 (Bt878) (=Prolink 878TV Rev.3x) |
| - MXTV-9578CP (Bt878) (= Prolink PV-BT878P+4E) |
| |
| Iomega |
| ~~~~~~ |
| |
| Buz (zr36067, zr36060, saa7111, saa7185) |
| |
| LML |
| ~~~ |
| LML33 (zr36067, zr36060, bt819, bt856) |
| |
| Grandtec |
| ~~~~~~~~ |
| |
| Models: |
| |
| - Grand Video Capture (Bt848) |
| - Multi Capture Card (Bt878) |
| |
| Koutech |
| ~~~~~~~ |
| |
| Models: |
| |
| - KW-606 (Bt848) |
| - KW-607 (Bt848 capture only) |
| - KW-606RSF |
| - KW-607A (capture only) |
| - KW-608 (Zoran capture only) |
| |
| IODATA (jp) |
| ~~~~~~~~~~~ |
| |
| Models: |
| |
| - GV-BCTV/PCI |
| - GV-BCTV2/PCI |
| - GV-BCTV3/PCI |
| - GV-BCTV4/PCI |
| - GV-VCP/PCI (capture only) |
| - GV-VCP2/PCI (capture only) |
| |
| Canopus (jp) |
| ~~~~~~~~~~~~ |
| |
| WinDVR = Kworld "KW-TVL878RF" |
| |
| www.sigmacom.co.kr |
| ~~~~~~~~~~~~~~~~~~ |
| |
| Sigma Cyber TV II |
| |
| www.sasem.co.kr |
| ~~~~~~~~~~~~~~~ |
| |
| Litte OnAir TV |
| |
| hama |
| ~~~~ |
| |
| TV/Radio-Tuner Card, PCI (Model 44677) = CPH051 |
| |
| Sigma Designs |
| ~~~~~~~~~~~~~ |
| |
| Hollywood plus (em8300, em9010, adv7175), (PCB "M340-10") MPEG DVD decoder |
| |
| Formac |
| ~~~~~~ |
| |
| Models: |
| |
| - iProTV (Card for iMac Mezzanine slot, Bt848+SCSI) |
| - ProTV (Bt848) |
| - ProTV II = ProTV Stereo (Bt878) ["stereo" means FM stereo, tv is still mono] |
| |
| ATI |
| ~~~ |
| |
| Models: |
| |
| - TV-Wonder |
| - TV-Wonder VE |
| |
| Diamond Multimedia |
| ~~~~~~~~~~~~~~~~~~ |
| |
| DTV2000 (Bt848, tda9875) |
| |
| Aopen |
| ~~~~~ |
| |
| - VA1000 Plus (w/ Stereo) |
| - VA1000 Lite |
| - VA1000 (=LR90) |
| |
| Intel |
| ~~~~~ |
| |
| Models: |
| |
| - Smart Video Recorder (ISA full-length) |
| - Smart Video Recorder pro (ISA half-length) |
| - Smart Video Recorder III (Bt848) |
| |
| STB |
| ~~~ |
| |
| Models: |
| |
| - STB Gateway 6000704 (bt878) |
| - STB Gateway 6000699 (bt848) |
| - STB Gateway 6000402 (bt848) |
| - STB TV130 PCI |
| |
| Videologic |
| ~~~~~~~~~~ |
| |
| Models: |
| |
| - Captivator Pro/TV (ISA?) |
| - Captivator PCI/VC (Bt848 bundled with camera) (capture only) |
| |
| Technotrend |
| ~~~~~~~~~~~~ |
| |
| Models: |
| |
| - TT-SAT PCI (PCB "Sat-PCI Rev.:1.3.1"; zr36125, vpx3225d, stc0056a, Tuner:BSKE6-155A |
| - TT-DVB-Sat |
| - revisions 1.1, 1.3, 1.5, 1.6 and 2.1 |
| - This card is sold as OEM from: |
| |
| - Siemens DVB-s Card |
| - Hauppauge WinTV DVB-S |
| - Technisat SkyStar 1 DVB |
| - Galaxis DVB Sat |
| |
| - Now this card is called TT-PCline Premium Family |
| - TT-Budget (saa7146, bsru6-701a) |
| This card is sold as OEM from: |
| |
| - Hauppauge WinTV Nova |
| - Satelco Standard PCI (DVB-S) |
| - TT-DVB-C PCI |
| |
| Teles |
| ~~~~~ |
| |
| DVB-s (Rev. 2.2, BSRV2-301A, data only?) |
| |
| Remote Vision |
| ~~~~~~~~~~~~~ |
| |
| MX RV605 (Bt848 capture only) |
| |
| Boeder |
| ~~~~~~ |
| |
| Models: |
| |
| - PC ChatCam (Model 68252) (Bt848 capture only) |
| - Tv/Fm Capture Card (Model 68404) = PV951 |
| |
| Media-Surfer (esc-kathrein.de) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - Sat-Surfer (ISA) |
| - Sat-Surfer PCI = Techni-PC-Sat |
| - Cable-Surfer 1 |
| - Cable-Surfer 2 |
| - Cable-Surfer PCI (zr36120) |
| - Audio-Surfer (ISA Radio card) |
| |
| Jetway (www.jetway.com.tw) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - JW-TV 878M |
| - JW-TV 878 = KWorld KW-TV878RF |
| |
| Galaxis |
| ~~~~~~~ |
| |
| Models: |
| |
| - Galaxis DVB Card S CI |
| - Galaxis DVB Card C CI |
| - Galaxis DVB Card S |
| - Galaxis DVB Card C |
| - Galaxis plug.in S [neuer Name: Galaxis DVB Card S CI |
| |
| Hauppauge |
| ~~~~~~~~~ |
| |
| Models: |
| |
| - many many WinTV models ... |
| - WinTV DVBs = Technotrend Premium 1.3 |
| - WinTV NOVA = Technotrend Budget 1.1 "S-DVB DATA" |
| - WinTV NOVA-CI "SDVBACI" |
| - WinTV Nova USB (=Technotrend USB 1.0) |
| - WinTV-Nexus-s (=Technotrend Premium 2.1 or 2.2) |
| - WinTV PVR |
| - WinTV PVR 250 |
| - WinTV PVR 450 |
| |
| US models |
| |
| -990 WinTV-PVR-350 (249USD) (iTVC15 chipset + radio) |
| -980 WinTV-PVR-250 (149USD) (iTVC15 chipset) |
| -880 WinTV-PVR-PCI (199USD) (KFIR chipset + bt878) |
| -881 WinTV-PVR-USB |
| -190 WinTV-GO |
| -191 WinTV-GO-FM |
| -404 WinTV |
| -401 WinTV-radio |
| -495 WinTV-Theater |
| -602 WinTV-USB |
| -621 WinTV-USB-FM |
| -600 USB-Live |
| -698 WinTV-HD |
| -697 WinTV-D |
| -564 WinTV-Nexus-S |
| |
| Deutsche Modelle: |
| |
| -603 WinTV GO |
| -719 WinTV Primio-FM |
| -718 WinTV PCI-FM |
| -497 WinTV Theater |
| -569 WinTV USB |
| -568 WinTV USB-FM |
| -882 WinTV PVR |
| -981 WinTV PVR 250 |
| -891 WinTV-PVR-USB |
| -541 WinTV Nova |
| -488 WinTV Nova-Ci |
| -564 WinTV-Nexus-s |
| -727 WinTV-DVB-c |
| -545 Common Interface |
| -898 WinTV-Nova-USB |
| |
| UK models: |
| |
| -607 WinTV Go |
| -693,793 WinTV Primio FM |
| -647,747 WinTV PCI FM |
| -498 WinTV Theater |
| -883 WinTV PVR |
| -893 WinTV PVR USB (Duplicate entry) |
| -566 WinTV USB (UK) |
| -573 WinTV USB FM |
| -429 Impact VCB (bt848) |
| -600 USB Live (Video-In 1x Comp, 1xSVHS) |
| -542 WinTV Nova |
| -717 WinTV DVB-S |
| -909 Nova-t PCI |
| -893 Nova-t USB (Duplicate entry) |
| -802 MyTV |
| -804 MyView |
| -809 MyVideo |
| -872 MyTV2Go FM |
| -546 WinTV Nova-S CI |
| -543 WinTV Nova |
| -907 Nova-S USB |
| -908 Nova-T USB |
| -717 WinTV Nexus-S |
| -157 DEC3000-s Standalone + USB |
| |
| Spain: |
| |
| -685 WinTV-Go |
| -690 WinTV-PrimioFM |
| -416 WinTV-PCI Nicam Estereo |
| -677 WinTV-PCI-FM |
| -699 WinTV-Theater |
| -683 WinTV-USB |
| -678 WinTV-USB-FM |
| -983 WinTV-PVR-250 |
| -883 WinTV-PVR-PCI |
| -993 WinTV-PVR-350 |
| -893 WinTV-PVR-USB |
| -728 WinTV-DVB-C PCI |
| -832 MyTV2Go |
| -869 MyTV2Go-FM |
| -805 MyVideo (USB) |
| |
| |
| Matrix-Vision |
| ~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - MATRIX-Vision MV-Delta |
| - MATRIX-Vision MV-Delta 2 |
| - MVsigma-SLC (Bt848) |
| |
| Conceptronic (.net) |
| ~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - TVCON FM, TV card w/ FM = CPH05x |
| - TVCON = CPH06x |
| |
| BestData |
| ~~~~~~~~ |
| |
| Models: |
| |
| - HCC100 = VCC100rev1 + camera |
| - VCC100 rev1 (bt848) |
| - VCC100 rev2 (bt878) |
| |
| Gallant (www.gallantcom.com) www.minton.com.tw |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - Intervision IV-510 (capture only bt8x8) |
| - Intervision IV-550 (bt8x8) |
| - Intervision IV-100 (zoran) |
| - Intervision IV-1000 (bt8x8) |
| |
| Asonic (www.asonic.com.cn) (website down) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| SkyEye tv 878 |
| |
| Hoontech |
| ~~~~~~~~ |
| |
| 878TV/FM |
| |
| Teppro (www.itcteppro.com.tw) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - ITC PCITV (Card Ver 1.0) "Teppro TV1/TVFM1 Card" |
| - ITC PCITV (Card Ver 2.0) |
| - ITC PCITV (Card Ver 3.0) = "PV-BT878P+ (REV.9D)" |
| - ITC PCITV (Card Ver 4.0) |
| - TEPPRO IV-550 (For BT848 Main Chip) |
| - ITC DSTTV (bt878, satellite) |
| - ITC VideoMaker (saa7146, StreamMachine sm2110, tvtuner) "PV-SM2210P+ (REV:1C)" |
| |
| Kworld (www.kworld.com.tw) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| PC TV Station: |
| |
| - KWORLD KW-TV878R TV (no radio) |
| - KWORLD KW-TV878RF TV (w/ radio) |
| - KWORLD KW-TVL878RF (low profile) |
| - KWORLD KW-TV713XRF (saa7134) |
| |
| |
| MPEG TV Station (same cards as above plus WinDVR Software MPEG en/decoder) |
| |
| - KWORLD KW-TV878R -Pro TV (no Radio) |
| - KWORLD KW-TV878RF-Pro TV (w/ Radio) |
| - KWORLD KW-TV878R -Ultra TV (no Radio) |
| - KWORLD KW-TV878RF-Ultra TV (w/ Radio) |
| |
| JTT/ Justy Corp.(http://www.jtt.ne.jp/) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| JTT-02 (JTT TV) "TV watchmate pro" (bt848) |
| |
| ADS www.adstech.com |
| ~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - Channel Surfer TV ( CHX-950 ) |
| - Channel Surfer TV+FM ( CHX-960FM ) |
| |
| AVEC www.prochips.com |
| ~~~~~~~~~~~~~~~~~~~~~ |
| |
| AVEC Intercapture (bt848, tea6320) |
| |
| NoBrand |
| ~~~~~~~ |
| |
| TV Excel = Australian Name for "PV-BT878P+ 8E" or "878TV Rev.3\_" |
| |
| Mach www.machspeed.com |
| ~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Mach TV 878 |
| |
| Eline www.eline-net.com/ |
| ~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - Eline Vision TVMaster / TVMaster FM (ELV-TVM/ ELV-TVM-FM) = LR26 (bt878) |
| - Eline Vision TVMaster-2000 (ELV-TVM-2000, ELV-TVM-2000-FM)= LR138 (saa713x) |
| |
| Spirit |
| ~~~~~~ |
| |
| - Spirit TV Tuner/Video Capture Card (bt848) |
| |
| Boser www.boser.com.tw |
| ~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - HS-878 Mini PCI Capture Add-on Card |
| - HS-879 Mini PCI 3D Audio and Capture Add-on Card (w/ ES1938 Solo-1) |
| |
| Satelco www.citycom-gmbh.de, www.satelco.de |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - TV-FM =KNC1 saa7134 |
| - Standard PCI (DVB-S) = Technotrend Budget |
| - Standard PCI (DVB-S) w/ CI |
| - Satelco Highend PCI (DVB-S) = Technotrend Premium |
| |
| |
| Sensoray www.sensoray.com |
| ~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - Sensoray 311 (PC/104 bus) |
| - Sensoray 611 (PCI) |
| |
| CEI (Chartered Electronics Industries Pte Ltd [CEI] [FCC ID HBY]) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - TV Tuner - HBY-33A-RAFFLES Brooktree Bt848KPF + Philips |
| - TV Tuner MG9910 - HBY33A-TVO CEI + Philips SAA7110 + OKI M548262 + ST STV8438CV |
| - Primetime TV (ISA) |
| |
| - acquired by Singapore Technologies |
| - now operating as Chartered Semiconductor Manufacturing |
| - Manufacturer of video cards is listed as: |
| |
| - Cogent Electronics Industries [CEI] |
| |
| AITech |
| ~~~~~~ |
| |
| Models: |
| |
| - Wavewatcher TV (ISA) |
| - AITech WaveWatcher TV-PCI = can be LR26 (Bt848) or LR50 (BT878) |
| - WaveWatcher TVR-202 TV/FM Radio Card (ISA) |
| |
| MAXRON |
| ~~~~~~ |
| |
| Maxron MaxTV/FM Radio (KW-TV878-FNT) = Kworld or JW-TV878-FBK |
| |
| www.ids-imaging.de |
| ~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - Falcon Series (capture only) |
| |
| In USA: http://www.theimagingsource.com/ |
| - DFG/LC1 |
| |
| www.sknet-web.co.jp |
| ~~~~~~~~~~~~~~~~~~~ |
| |
| SKnet Monster TV (saa7134) |
| |
| A-Max www.amaxhk.com (Colormax, Amax, Napa) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| APAC Viewcomp 878 |
| |
| Cybertainment |
| ~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - CyberMail AV Video Email Kit w/ PCI Capture Card (capture only) |
| - CyberMail Xtreme |
| |
| These are Flyvideo |
| |
| VCR (http://www.vcrinc.com/) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Video Catcher 16 |
| |
| Twinhan |
| ~~~~~~~ |
| |
| Models: |
| |
| - DST Card/DST-IP (bt878, twinhan asic) VP-1020 |
| - Sold as: |
| |
| - KWorld DVBS Satellite TV-Card |
| - Powercolor DSTV Satellite Tuner Card |
| - Prolink Pixelview DTV2000 |
| - Provideo PV-911 Digital Satellite TV Tuner Card With Common Interface ? |
| |
| - DST-CI Card (DVB Satellite) VP-1030 |
| - DCT Card (DVB cable) |
| |
| MSI |
| ~~~ |
| |
| Models: |
| |
| - MSI TV@nywhere Tuner Card (MS-8876) (CX23881/883) Not Bt878 compatible. |
| - MS-8401 DVB-S |
| |
| Focus www.focusinfo.com |
| ~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| InVideo PCI (bt878) |
| |
| Sdisilk www.sdisilk.com/ |
| ~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - SDI Silk 100 |
| - SDI Silk 200 SDI Input Card |
| |
| www.euresys.com |
| ~~~~~~~~~~~~~~~ |
| |
| PICOLO series |
| |
| PMC/Pace |
| ~~~~~~~~ |
| |
| www.pacecom.co.uk website closed |
| |
| Mercury www.kobian.com (UK and FR) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - LR50 |
| - LR138RBG-Rx == LR138 |
| |
| TEC sound |
| ~~~~~~~~~ |
| |
| TV-Mate = Zoltrix VP-8482 |
| |
| Though educated googling found: www.techmakers.com |
| |
| (package and manuals don't have any other manufacturer info) TecSound |
| |
| Lorenzen www.lorenzen.de |
| ~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| SL DVB-S PCI = Technotrend Budget PCI (su1278 or bsru version) |
| |
| Origo (.uk) www.origo2000.com |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| PC TV Card = LR50 |
| |
| I/O Magic www.iomagic.com |
| ~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| PC PVR - Desktop TV Personal Video Recorder DR-PCTV100 = Pinnacle ROB2D-51009464 4.0 + Cyberlink PowerVCR II |
| |
| Arowana |
| ~~~~~~~ |
| |
| TV-Karte / Poso Power TV (?) = Zoltrix VP-8482 (?) |
| |
| iTVC15 boards |
| ~~~~~~~~~~~~~ |
| |
| kuroutoshikou.com ITVC15 |
| yuan.com MPG160 PCI TV (Internal PCI MPEG2 encoder card plus TV-tuner) |
| |
| Asus www.asuscom.com |
| ~~~~~~~~~~~~~~~~~~~~ |
| |
| Models: |
| |
| - Asus TV Tuner Card 880 NTSC (low profile, cx23880) |
| - Asus TV (saa7134) |
| |
| Hoontech |
| ~~~~~~~~ |
| |
| http://www.hoontech.de/ |
| |
| - HART Vision 848 (H-ART Vision 848) |
| - HART Vision 878 (H-Art Vision 878) |
| |
| |
| |
| Chips used at bttv devices |
| -------------------------- |
| |
| - all boards: |
| |
| - Brooktree Bt848/848A/849/878/879: video capture chip |
| |
| - Board specific |
| |
| - Miro PCTV: |
| |
| - Philips or Temic Tuner |
| |
| - Hauppauge Win/TV pci (version 405): |
| |
| - Microchip 24LC02B or Philips 8582E2Y: |
| |
| - 256 Byte EEPROM with configuration information |
| - I2C 0xa0-0xa1, (24LC02B also responds to 0xa2-0xaf) |
| |
| - Philips SAA5246AGP/E: Videotext decoder chip, I2C 0x22-0x23 |
| |
| - TDA9800: sound decoder |
| |
| - Winbond W24257AS-35: 32Kx8 CMOS static RAM (Videotext buffer mem) |
| |
| - 14052B: analog switch for selection of sound source |
| |
| - PAL: |
| |
| - TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners |
| - TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3 |
| |
| - NTSC: |
| |
| - TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners |
| - TSA5518: no datasheet available on Philips site |
| |
| - STB TV pci: |
| |
| - ??? |
| - if you want better support for STB cards send me info! |
| Look at the board! What chips are on it? |
| |
| |
| |
| |
| Specs |
| ----- |
| |
| Philips http://www.Semiconductors.COM/pip/ |
| |
| Conexant http://www.conexant.com/ |
| |
| Micronas http://www.micronas.com/en/home/index.html |
| |
| Thanks |
| ------ |
| |
| Many thanks to: |
| |
| - Markus Schroeder <schroedm@uni-duesseldorf.de> for information on the Bt848 |
| and tuner programming and his control program xtvc. |
| |
| - Martin Buck <martin-2.buck@student.uni-ulm.de> for his great Videotext |
| package. |
| |
| - Gerd Hoffmann for the MSP3400 support and the modular |
| I2C, tuner, ... support. |
| |
| |
| - MATRIX Vision for giving us 2 cards for free, which made support of |
| single crystal operation possible. |
| |
| - MIRO for providing a free PCTV card and detailed information about the |
| components on their cards. (E.g. how the tuner type is detected) |
| Without their card I could not have debugged the NTSC mode. |
| |
| - Hauppauge for telling how the sound input is selected and what components |
| they do and will use on their radio cards. |
| Also many thanks for faxing me the FM1216 data sheet. |
| |
| Contributors |
| ------------ |
| |
| Michael Chu <mmchu@pobox.com> |
| AverMedia fix and more flexible card recognition |
| |
| Alan Cox <alan@lxorguk.ukuu.org.uk> |
| Video4Linux interface and 2.1.x kernel adaptation |
| |
| Chris Kleitsch |
| Hardware I2C |
| |
| Gerd Hoffmann |
| Radio card (ITT sound processor) |
| |
| bigfoot <bigfoot@net-way.net> |
| |
| Ragnar Hojland Espinosa <ragnar@macula.net> |
| ConferenceTV card |
| |
| |
| + many more (please mail me if you are missing in this list and would |
| like to be mentioned) |