blob: 5be0e8fd2633c20e2d87abc843b53fca437942be [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
// Copyright (c) 2021 Facebook Inc.
/dts-v1/;
#include "aspeed-g6.dtsi"
#include <dt-bindings/gpio/aspeed-gpio.h>
#include <dt-bindings/usb/pd.h>
#include <dt-bindings/leds/leds-pca955x.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/i2c/i2c.h>
/ {
model = "Facebook Bletchley BMC";
compatible = "facebook,bletchley-bmc", "aspeed,ast2600";
aliases {
serial4 = &uart5;
};
chosen {
bootargs = "console=ttyS4,57600n8";
};
memory@80000000 {
device_type = "memory";
reg = <0x80000000 0x80000000>;
};
iio-hwmon {
compatible = "iio-hwmon";
io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
<&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
<&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
};
spi1_gpio: spi1-gpio {
compatible = "spi-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpio-sck = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
gpio-mosi = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
gpio-miso = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
num-chipselects = <1>;
cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
tpm@0 {
compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
spi-max-frequency = <33000000>;
reg = <0>;
};
};
switchphy: ethernet-phy@0 {
// Fixed link
};
front_gpio_leds {
compatible = "gpio-leds";
sys_log_id {
default-state = "off";
gpios = <&front_leds 0 GPIO_ACTIVE_LOW>;
};
};
fan_gpio_leds {
compatible = "gpio-leds";
fan0_blue {
retain-state-shutdown;
default-state = "on";
gpios = <&fan_leds 8 GPIO_ACTIVE_HIGH>;
};
fan1_blue {
retain-state-shutdown;
default-state = "on";
gpios = <&fan_leds 9 GPIO_ACTIVE_HIGH>;
};
fan2_blue {
retain-state-shutdown;
default-state = "on";
gpios = <&fan_leds 10 GPIO_ACTIVE_HIGH>;
};
fan3_blue {
retain-state-shutdown;
default-state = "on";
gpios = <&fan_leds 11 GPIO_ACTIVE_HIGH>;
};
fan0_amber {
retain-state-shutdown;
default-state = "off";
gpios = <&fan_leds 12 GPIO_ACTIVE_HIGH>;
};
fan1_amber {
retain-state-shutdown;
default-state = "off";
gpios = <&fan_leds 13 GPIO_ACTIVE_HIGH>;
};
fan2_amber {
retain-state-shutdown;
default-state = "off";
gpios = <&fan_leds 14 GPIO_ACTIVE_HIGH>;
};
fan3_amber {
retain-state-shutdown;
default-state = "off";
gpios = <&fan_leds 15 GPIO_ACTIVE_HIGH>;
};
};
sled1_gpio_leds {
compatible = "gpio-leds";
sled1_amber {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled1_leds 0 GPIO_ACTIVE_LOW>;
};
sled1_blue {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled1_leds 1 GPIO_ACTIVE_LOW>;
};
};
sled2_gpio_leds {
compatible = "gpio-leds";
sled2_amber {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled2_leds 0 GPIO_ACTIVE_LOW>;
};
sled2_blue {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled2_leds 1 GPIO_ACTIVE_LOW>;
};
};
sled3_gpio_leds {
compatible = "gpio-leds";
sled3_amber {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled3_leds 0 GPIO_ACTIVE_LOW>;
};
sled3_blue {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled3_leds 1 GPIO_ACTIVE_LOW>;
};
};
sled4_gpio_leds {
compatible = "gpio-leds";
sled4_amber {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled4_leds 0 GPIO_ACTIVE_LOW>;
};
sled4_blue {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled4_leds 1 GPIO_ACTIVE_LOW>;
};
};
sled5_gpio_leds {
compatible = "gpio-leds";
sled5_amber {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled5_leds 0 GPIO_ACTIVE_LOW>;
};
sled5_blue {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>;
};
};
sled6_gpio_leds {
compatible = "gpio-leds";
sled6_amber {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled6_leds 0 GPIO_ACTIVE_LOW>;
};
sled6_blue {
retain-state-shutdown;
default-state = "keep";
gpios = <&sled6_leds 1 GPIO_ACTIVE_LOW>;
};
};
gpio-keys {
compatible = "gpio-keys";
presence-sled1 {
label = "presence-sled1";
gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
linux,code = <ASPEED_GPIO(H, 2)>;
};
presence-sled2 {
label = "presence-sled2";
gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
linux,code = <ASPEED_GPIO(H, 3)>;
};
presence-sled3 {
label = "presence-sled3";
gpios = <&gpio0 ASPEED_GPIO(H, 4) GPIO_ACTIVE_LOW>;
linux,code = <ASPEED_GPIO(H, 4)>;
};
presence-sled4 {
label = "presence-sled4";
gpios = <&gpio0 ASPEED_GPIO(H, 5) GPIO_ACTIVE_LOW>;
linux,code = <ASPEED_GPIO(H, 5)>;
};
presence-sled5 {
label = "presence-sled5";
gpios = <&gpio0 ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
linux,code = <ASPEED_GPIO(H, 6)>;
};
presence-sled6 {
label = "presence-sled6";
gpios = <&gpio0 ASPEED_GPIO(H, 7) GPIO_ACTIVE_LOW>;
linux,code = <ASPEED_GPIO(H, 7)>;
};
};
vbus_sled1: vbus_sled1 {
compatible = "regulator-fixed";
regulator-name = "vbus_sled1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&sled1_ioexp 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vbus_sled2: vbus_sled2 {
compatible = "regulator-fixed";
regulator-name = "vbus_sled2";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&sled2_ioexp 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vbus_sled3: vbus_sled3 {
compatible = "regulator-fixed";
regulator-name = "vbus_sled3";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&sled3_ioexp 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vbus_sled4: vbus_sled4 {
compatible = "regulator-fixed";
regulator-name = "vbus_sled4";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&sled4_ioexp 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vbus_sled5: vbus_sled5 {
compatible = "regulator-fixed";
regulator-name = "vbus_sled5";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&sled5_ioexp 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vbus_sled6: vbus_sled6 {
compatible = "regulator-fixed";
regulator-name = "vbus_sled6";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&sled6_ioexp 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
&mac2 {
status = "okay";
phy-mode = "rgmii";
phy-handle = <&switchphy>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_rgmii3_default>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
&fmc {
status = "okay";
flash@0 {
status = "okay";
m25p,fast-read;
label = "bmc";
spi-max-frequency = <50000000>;
#include "openbmc-flash-layout-128.dtsi"
};
flash@1 {
status = "okay";
m25p,fast-read;
label = "alt-bmc";
spi-max-frequency = <50000000>;
};
};
&spi2 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi2_default>;
flash@0 {
status = "okay";
m25p,fast-read;
label = "pnor";
spi-max-frequency = <50000000>;
};
};
&i2c0 {
status = "okay";
ina230@45 {
compatible = "ti,ina230";
reg = <0x45>;
shunt-resistor = <2000>;
};
mp5023@40 {
compatible = "mps,mp5023";
reg = <0x40>;
};
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
sled1_ioexp41: pca9536@41 {
compatible = "nxp,pca9536";
reg = <0x41>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"SLED1_SWD_MUX", "SLED1_XRES_SWD_N",
"SLED1_CLKREQ_N", "SLED1_PCIE_PWR_EN";
};
sled1_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(M, 0) IRQ_TYPE_LEVEL_LOW>;
gpio-line-names =
"SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
"SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
"SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
"SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
};
sled1_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","SLED1_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
sled1_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(B, 0) IRQ_TYPE_LEVEL_LOW>;
vbus-supply = <&vbus_sled1>;
connector {
compatible = "usb-c-connector";
label = "USB-C";
power-role = "source";
data-role = "host";
pd-disable;
typec-power-opmode = "default";
};
};
eeprom@54 {
compatible = "atmel,24c64";
reg = <0x54>;
};
};
&i2c1 {
status = "okay";
ina230@45 {
compatible = "ti,ina230";
reg = <0x45>;
shunt-resistor = <2000>;
};
mp5023@40 {
compatible = "mps,mp5023";
reg = <0x40>;
};
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
sled2_ioexp41: pca9536@41 {
compatible = "nxp,pca9536";
reg = <0x41>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"SLED2_SWD_MUX", "SLED2_XRES_SWD_N",
"SLED2_CLKREQ_N", "SLED2_PCIE_PWR_EN";
};
sled2_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(M, 1) IRQ_TYPE_LEVEL_LOW>;
gpio-line-names =
"SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
"SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
"SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
"SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
};
sled2_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","SLED2_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
sled2_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(B, 1) IRQ_TYPE_LEVEL_LOW>;
vbus-supply = <&vbus_sled2>;
connector {
compatible = "usb-c-connector";
label = "USB-C";
power-role = "source";
data-role = "host";
pd-disable;
typec-power-opmode = "default";
};
};
eeprom@54 {
compatible = "atmel,24c64";
reg = <0x54>;
};
};
&i2c2 {
status = "okay";
ina230@45 {
compatible = "ti,ina230";
reg = <0x45>;
shunt-resistor = <2000>;
};
mp5023@40 {
compatible = "mps,mp5023";
reg = <0x40>;
};
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
sled3_ioexp41: pca9536@41 {
compatible = "nxp,pca9536";
reg = <0x41>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"SLED3_SWD_MUX", "SLED3_XRES_SWD_N",
"SLED3_CLKREQ_N", "SLED3_PCIE_PWR_EN";
};
sled3_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(M, 2) IRQ_TYPE_LEVEL_LOW>;
gpio-line-names =
"SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
"SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
"SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
"SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
};
sled3_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","SLED3_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
sled3_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(B, 7) IRQ_TYPE_LEVEL_LOW>;
vbus-supply = <&vbus_sled3>;
connector {
compatible = "usb-c-connector";
label = "USB-C";
power-role = "source";
data-role = "host";
pd-disable;
typec-power-opmode = "default";
};
};
eeprom@54 {
compatible = "atmel,24c64";
reg = <0x54>;
};
};
&i2c3 {
status = "okay";
ina230@45 {
compatible = "ti,ina230";
reg = <0x45>;
shunt-resistor = <2000>;
};
mp5023@40 {
compatible = "mps,mp5023";
reg = <0x40>;
};
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
sled4_ioexp41: pca9536@41 {
compatible = "nxp,pca9536";
reg = <0x41>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"SLED4_SWD_MUX", "SLED4_XRES_SWD_N",
"SLED4_CLKREQ_N", "SLED4_PCIE_PWR_EN";
};
sled4_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(M, 3) IRQ_TYPE_LEVEL_LOW>;
gpio-line-names =
"SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
"SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
"SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
"SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
};
sled4_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","SLED4_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
sled4_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(S, 7) IRQ_TYPE_LEVEL_LOW>;
vbus-supply = <&vbus_sled4>;
connector {
compatible = "usb-c-connector";
label = "USB-C";
power-role = "source";
data-role = "host";
pd-disable;
typec-power-opmode = "default";
};
};
eeprom@54 {
compatible = "atmel,24c64";
reg = <0x54>;
};
};
&i2c4 {
status = "okay";
ina230@45 {
compatible = "ti,ina230";
reg = <0x45>;
shunt-resistor = <2000>;
};
mp5023@40 {
compatible = "mps,mp5023";
reg = <0x40>;
};
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
sled5_ioexp41: pca9536@41 {
compatible = "nxp,pca9536";
reg = <0x41>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"SLED5_SWD_MUX", "SLED5_XRES_SWD_N",
"SLED5_CLKREQ_N", "SLED5_PCIE_PWR_EN";
};
sled5_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(M, 4) IRQ_TYPE_LEVEL_LOW>;
gpio-line-names =
"SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
"SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
"SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
"SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
};
sled5_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","SLED5_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
sled5_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(Y, 3) IRQ_TYPE_LEVEL_LOW>;
vbus-supply = <&vbus_sled5>;
connector {
compatible = "usb-c-connector";
label = "USB-C";
power-role = "source";
data-role = "host";
pd-disable;
typec-power-opmode = "default";
};
};
eeprom@54 {
compatible = "atmel,24c64";
reg = <0x54>;
};
};
&i2c5 {
status = "okay";
ina230@45 {
compatible = "ti,ina230";
reg = <0x45>;
shunt-resistor = <2000>;
};
mp5023@40 {
compatible = "mps,mp5023";
reg = <0x40>;
};
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
sled6_ioexp41: pca9536@41 {
compatible = "nxp,pca9536";
reg = <0x41>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"SLED6_SWD_MUX", "SLED6_XRES_SWD_N",
"SLED6_CLKREQ_N", "SLED6_PCIE_PWR_EN";
};
sled6_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>;
gpio-line-names =
"SLED6_MS_DETECT1","SLED6_VBUS_BMC_EN","SLED6_INA230_ALERT","SLED6_P12V_STBY_ALERT",
"SLED6_SSD_ALERT","SLED6_MS_DETECT0","SLED6_RST_CCG5","SLED6_FUSB302_INT",
"SLED6_MD_STBY_RESET","SLED6_MD_IOEXP_EN_FAULT","SLED6_MD_DIR","SLED6_MD_DECAY",
"SLED6_MD_MODE1","SLED6_MD_MODE2","SLED6_MD_MODE3","power-host6";
};
sled6_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"led-sled6-amber","led-sled6-blue","SLED6_RST_IOEXP","SLED6_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
sled6_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
interrupts = <ASPEED_GPIO(I, 7) IRQ_TYPE_LEVEL_LOW>;
vbus-supply = <&vbus_sled6>;
connector {
compatible = "usb-c-connector";
label = "USB-C";
power-role = "source";
data-role = "host";
pd-disable;
typec-power-opmode = "default";
};
};
eeprom@54 {
compatible = "atmel,24c64";
reg = <0x54>;
};
};
&i2c6 {
status = "okay";
eeprom@56 {
compatible = "atmel,24c64";
reg = <0x56>;
};
rtc@51 {
/* in-chip rtc disabled, use external rtc (battery-backed) */
compatible = "nxp,pcf85263";
reg = <0x51>;
};
};
&i2c7 {
status = "okay";
eeprom@54 {
compatible = "atmel,24c64";
reg = <0x54>;
};
};
&i2c9 {
status = "okay";
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
};
&i2c10 {
status = "okay";
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
front_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"led-fault-identify","power-p5v-stby-good",
"power-p1v0-dvdd-good","power-p1v0-avdd-good",
"","","","",
"","","","",
"","","","";
};
};
&i2c12 {
status = "okay";
adm1278@11 {
compatible = "adi,adm1278";
reg = <0x11>;
shunt-resistor-micro-ohms = <300>;
adi,volt-curr-sample-average = <128>;
adi,power-sample-average = <128>;
};
tmp421@4c {
compatible = "ti,tmp421";
reg = <0x4c>;
};
tmp421@4d {
compatible = "ti,tmp421";
reg = <0x4d>;
};
fan_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
"presence-fan0","presence-fan1",
"presence-fan2","presence-fan3",
"power-fan0-good","power-fan1-good",
"power-fan2-good","power-fan3-good",
"","","","",
"","","","";
};
};
&i2c13 {
multi-master;
aspeed,hw-timeout-ms = <1000>;
status = "okay";
//USB Debug Connector
ipmb13@10 {
compatible = "ipmb-dev";
reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
i2c-protocol;
};
};
&gpio0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpiov2_unbiased_default>;
gpio-line-names =
/*A0-A7*/ "","","","","","","","",
/*B0-B7*/ "FUSB302_SLED1_INT_N","FUSB302_SLED2_INT_N",
"SEL_SPI2_MUX","SPI2_MUX1",
"SPI2_MUX2","SPI2_MUX3",
"","FUSB302_SLED3_INT_N",
/*C0-C7*/ "","","","","","","","",
/*D0-D7*/ "","","","","","","","",
/*E0-E7*/ "","","","","","","","",
/*F0-F7*/ "BMC_SLED1_STCK","BMC_SLED2_STCK",
"BMC_SLED3_STCK","BMC_SLED4_STCK",
"BMC_SLED5_STCK","BMC_SLED6_STCK",
"","",
/*G0-G7*/ "BSM_FRU_WP","SWITCH_FRU_MUX","","FM_SOL_UART_CH_SEL",
"PWRGD_P1V05_VDDCORE","PWRGD_P1V5_VDD","","",
/*H0-H7*/ "presence-riser1","presence-riser2",
"presence-sled1","presence-sled2",
"presence-sled3","presence-sled4",
"presence-sled5","presence-sled6",
/*I0-I7*/ "REV_ID0","",
"REV_ID1","REV_ID2",
"","BSM_FLASH_WP_STATUS",
"BMC_TPM_PRES_N","FUSB302_SLED6_INT_N",
/*J0-J7*/ "","","","","","","","",
/*K0-K7*/ "","","","","","","","",
/*L0-L7*/ "","","","","","BMC_RTC_INT","","",
/*M0-M7*/ "ALERT_SLED1_N","ALERT_SLED2_N",
"ALERT_SLED3_N","ALERT_SLED4_N",
"ALERT_SLED5_N","ALERT_SLED6_N",
"","USB_DEBUG_PWR_BTN_N",
/*N0-N7*/ "LED_POSTCODE_0","LED_POSTCODE_1",
"LED_POSTCODE_2","LED_POSTCODE_3",
"LED_POSTCODE_4","LED_POSTCODE_5",
"LED_POSTCODE_6","LED_POSTCODE_7",
/*O0-O7*/ "","","","",
"","BOARD_ID0","BOARD_ID1","BOARD_ID2",
/*P0-P7*/ "","","","","","","","BMC_HEARTBEAT",
/*Q0-Q7*/ "","","","","","","","",
/*R0-R7*/ "","","","","","","","",
/*S0-S7*/ "","","","BAT_DETECT",
"BMC_BT_WP0_N","BMC_BT_WP1_N","","FUSB302_SLED4_INT_N",
/*T0-T7*/ "","","","","","","","",
/*U0-U7*/ "","","","","","","","",
/*V0-V7*/ "PWRGD_CNS_PSU","RST_BMC_MVL_N",
"P12V_AUX_ALERT1_N","PSU_PRSNT",
"USB2_SEL0_A","USB2_SEL1_A",
"USB2_SEL0_B","USB2_SEL1_B",
/*W0-W7*/ "RST_FRONT_IOEXP_N","","","","","","","",
/*X0-X7*/ "","","","","","","","",
/*Y0-Y7*/ "BMC_SELF_HW_RST","BSM_PRSNT_N",
"BSM_FLASH_LATCH_N","FUSB302_SLED5_INT_N",
"","","","",
/*Z0-Z7*/ "","","","","","","","";
};
&adc0 {
vref = <1800>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
&pinctrl_adc2_default &pinctrl_adc3_default
&pinctrl_adc4_default &pinctrl_adc5_default
&pinctrl_adc6_default &pinctrl_adc7_default>;
};
&adc1 {
vref = <2500>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
&pinctrl_adc10_default &pinctrl_adc11_default
&pinctrl_adc12_default &pinctrl_adc13_default
&pinctrl_adc14_default &pinctrl_adc15_default>;
};
&mdio0 {
status = "okay";
/* TODO: Add Marvell 88E6191X */
};
&mdio3 {
status = "okay";
/* TODO: Add Marvell 88X3310 */
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&emmc_controller {
status = "okay";
};
&emmc {
status = "okay";
};
&pinctrl {
pinctrl_gpiov2_unbiased_default: gpiov2 {
pins = "AD14";
bias-disable;
};
};
&wdt1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wdtrst1_default>;
aspeed,reset-type = "soc";
aspeed,external-signal;
aspeed,ext-push-pull;
aspeed,ext-active-high;
aspeed,ext-pulse-duration = <256>;
};