blob: 5a77286136c7293c56edcd222c2a29e72c7a171d [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* Marvell 88F6281 GTW GE Board
*
* Lennert Buytenhek <buytenh@marvell.com>
* Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
*
* This file contains the definitions that are common between the 6281
* and 6282 variants of the Marvell Kirkwood Development Board.
*/
/dts-v1/;
#include "kirkwood.dtsi"
#include "kirkwood-6281.dtsi"
/ {
model = "Marvell 88F6281 GTW GE Board";
compatible = "marvell,mv88f6281gtw-ge", "marvell,kirkwood-88f6281", "marvell,kirkwood";
memory {
device_type = "memory";
reg = <0x00000000 0x20000000>; /* 512 MB */
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
stdout-path = &uart0;
};
ocp@f1000000 {
pin-controller@10000 {
pmx_usb_led: pmx-usb-led {
marvell,pins = "mpp12";
marvell,function = "gpo";
};
pmx_leds: pmx-leds {
marvell,pins = "mpp20", "mpp21";
marvell,function = "gpio";
};
pmx_keys: pmx-keys {
marvell,pins = "mpp46", "mpp47";
marvell,function = "gpio";
};
};
spi@10600 {
status = "okay";
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "mxicy,mx25l12805d", "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
mode = <0>;
};
};
serial@12000 {
status = "okay";
};
ehci@50000 {
status = "okay";
};
};
gpio-leds {
compatible = "gpio-leds";
pinctrl-0 = <&pmx_leds &pmx_usb_led>;
pinctrl-names = "default";
green-status {
label = "gtw:green:Status";
gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
};
red-status {
label = "gtw:red:Status";
gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
};
green-usb {
label = "gtw:green:USB";
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = <&pmx_keys>;
pinctrl-names = "default";
restart {
label = "SWR Button";
linux,code = <KEY_RESTART>;
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
};
wps {
label = "WPS Button";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
};
};
};
&mdio {
status = "okay";
switch@0 {
compatible = "marvell,mv88e6085";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "lan1";
};
port@1 {
reg = <1>;
label = "lan2";
};
port@2 {
reg = <2>;
label = "lan3";
};
port@3 {
reg = <3>;
label = "lan4";
};
port@4 {
reg = <4>;
label = "wan";
};
port@5 {
reg = <5>;
phy-mode = "rgmii-id";
ethernet = <&eth0port>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
};
&eth0 {
status = "okay";
ethernet0-port@0 {
speed = <1000>;
duplex = <1>;
phy-mode = "rgmii";
};
};
&pciec {
status = "okay";
};
&pcie0 {
status = "okay";
};