blob: b6e3c169797f0514fa261bcbadbbe346b5f09a6b [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
// Copyright (c) 2023 ARM Ltd.
/dts-v1/;
#include "sun50i-a64.dtsi"
#include "sun50i-a64-cpu-opp.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "Remix Mini PC";
compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
"allwinner,sun50i-a64";
aliases {
ethernet1 = &rtl8723bs;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
hdmi-connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
reg_vcc5v: regulator-5v {
/* board wide 5V supply directly from the DC input */
compatible = "regulator-fixed";
regulator-name = "vcc-5v";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
post-power-on-delay-ms = <200>;
};
};
&codec {
status = "okay";
};
&codec_analog {
cpvdd-supply = <&reg_eldo1>;
status = "okay";
};
&cpu0 {
cpu-supply = <&reg_dcdc2>;
};
&cpu1 {
cpu-supply = <&reg_dcdc2>;
};
&cpu2 {
cpu-supply = <&reg_dcdc2>;
};
&cpu3 {
cpu-supply = <&reg_dcdc2>;
};
&dai {
status = "okay";
};
&de {
status = "okay";
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&hdmi {
hvcc-supply = <&reg_dldo1>;
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
/* Connects to the AC200 chip */
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "okay";
};
&i2c0_pins {
bias-pull-up;
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <&reg_dcdc1>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
disable-wp;
bus-width = <4>;
status = "okay";
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
vmmc-supply = <&reg_aldo1>;
vqmmc-supply = <&reg_dldo4>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
rtl8723bs: wifi@1 {
reg = <1>;
interrupt-parent = <&r_pio>;
interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
interrupt-names = "host-wake";
};
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
vmmc-supply = <&reg_dcdc1>;
vqmmc-supply = <&reg_eldo1>;
bus-width = <8>;
non-removable;
mmc-hs200-1_8v;
mmc-hs400-1_8v;
cap-mmc-hw-reset;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&pio {
vcc-pb-supply = <&reg_dcdc1>;
vcc-pc-supply = <&reg_dcdc1>;
vcc-pd-supply = <&reg_dcdc1>;
vcc-pe-supply = <&reg_dcdc1>;
vcc-pf-supply = <&reg_dcdc1>;
vcc-pg-supply = <&reg_dldo4>;
vcc-ph-supply = <&reg_dcdc1>;
};
&r_ir {
status = "okay";
};
&r_pio {
/*
* We cannot add that supply for now since it would create a circular
* dependency between pinctrl, the regulator and the RSB Bus.
*
* vcc-pl-supply = <&reg_aldo2>;
*/
};
&r_rsb {
status = "okay";
axp803: pmic@3a3 {
compatible = "x-powers,axp803";
reg = <0x3a3>;
interrupt-parent = <&r_intc>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
x-powers,drive-vbus-en;
vin1-supply = <&reg_vcc5v>;
vin2-supply = <&reg_vcc5v>;
vin3-supply = <&reg_vcc5v>;
vin5-supply = <&reg_vcc5v>;
vin6-supply = <&reg_vcc5v>;
aldoin-supply = <&reg_vcc5v>;
dldoin-supply = <&reg_vcc5v>;
eldoin-supply = <&reg_vcc5v>;
fldoin-supply = <&reg_vcc5v>;
drivevbus-supply = <&reg_vcc5v>;
ips-supply = <&reg_vcc5v>;
status = "okay";
};
};
#include "axp803.dtsi"
&ac_power_supply {
status = "okay";
};
&reg_dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-3v3";
};
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1040000>;
regulator-max-microvolt = <1300000>;
regulator-name = "vdd-cpux";
};
/* DCDC3 is polyphased with DCDC2 */
&reg_dcdc5 {
regulator-always-on;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-name = "vcc-dram";
};
/* Deviates from the reset default of 1.1V. */
&reg_dcdc6 {
regulator-always-on;
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "vdd-sys";
};
&reg_aldo1 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};
&reg_aldo2 {
/* Specifying R_PIO consumer would create circular dependency. */
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-pl";
};
&reg_aldo3 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-pll-avcc";
};
/* AC200 power supply */
&reg_dldo1 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-ave-33";
};
&reg_dldo4 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi-io";
};
&reg_drivevbus {
regulator-name = "usb0-vbus";
status = "okay";
};
&reg_eldo1 {
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-cpvdd-dram-emmc";
};
/* Supplies the arisc management core, needed by TF-A to power off cores. */
&reg_fldo2 {
regulator-always-on;
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpus";
};
&reg_rtc_ldo {
regulator-name = "vcc-rtc";
};
&simplefb_hdmi {
vcc-hdmi-supply = <&reg_dcdc1>;
};
&sound {
simple-audio-card,aux-devs = <&codec_analog>;
simple-audio-card,widgets = "Microphone", "Microphone Jack",
"Headphone", "Headphone Jack";
simple-audio-card,routing =
"Left DAC", "DACL",
"Right DAC", "DACR",
"Headphone Jack", "HP",
"ADCL", "Left ADC",
"ADCR", "Right ADC",
"MIC2", "Microphone Jack";
status = "okay";
};
/* On the (unpopulated) UART pads. */
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
uart-has-rtscts;
status = "okay";
bluetooth {
compatible = "realtek,rtl8723bs-bt";
enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
max-speed = <1500000>;
};
};
&usb_otg {
dr_mode = "host";
status = "okay";
};
&usbphy {
usb0_vbus-supply = <&reg_drivevbus>;
usb1_vbus-supply = <&reg_drivevbus>;
status = "okay";
};