| // SPDX-License-Identifier: GPL-2.0-only |
| |
| /dts-v1/; |
| |
| #include "msm8916-pm8916.dtsi" |
| #include "msm8916-modem-qdsp6.dtsi" |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/leds/common.h> |
| |
| / { |
| model = "Longcheer L8150"; |
| compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916"; |
| chassis-type = "handset"; |
| |
| aliases { |
| mmc0 = &sdhc_1; /* eMMC */ |
| mmc1 = &sdhc_2; /* SD card */ |
| serial0 = &blsp_uart2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0"; |
| }; |
| |
| /* |
| * For some reason, the signed wcnss firmware is not relocatable. |
| * It must be loaded at 0x8b600000. Unfortunately, this also means that |
| * mpss_mem does not fit when loaded to the typical address at 0x86800000. |
| * |
| * Load wcnss_mem to the fixed address and relocate mpss_mem to the next |
| * working higher address. For some reason the modem firmware does not |
| * boot when placed at 0x8a800000 to 0x8e800000. |
| */ |
| reserved-memory { |
| /delete-node/ mpss@86800000; |
| /delete-node/ wcnss; |
| |
| wcnss_mem: wcnss@8b600000 { |
| reg = <0x0 0x8b600000 0x0 0x600000>; |
| no-map; |
| }; |
| |
| mpss_mem: mpss@8e800000 { |
| reg = <0x0 0x8e800000 0x0 0x5000000>; |
| no-map; |
| }; |
| }; |
| |
| battery: battery { |
| compatible = "simple-battery"; |
| voltage-min-design-microvolt = <3400000>; |
| voltage-max-design-microvolt = <4350000>; |
| energy-full-design-microwatt-hours = <9500000>; |
| charge-full-design-microamp-hours = <2500000>; |
| |
| ocv-capacity-celsius = <25>; |
| ocv-capacity-table-0 = <4330000 100>, <4265000 95>, |
| <4208000 90>, <4153000 85>, <4100000 80>, <4049000 75>, |
| <4001000 70>, <3962000 65>, <3919000 60>, <3872000 55>, |
| <3839000 50>, <3817000 45>, <3798000 40>, <3783000 35>, |
| <3767000 30>, <3747000 25>, <3729000 20>, <3709000 16>, |
| <3688000 13>, <3681000 11>, <3680000 10>, <3679000 9>, |
| <3677000 8>, <3674000 7>, <3666000 6>, <3641000 5>, |
| <3597000 4>, <3537000 3>, <3457000 2>, <3336000 1>, |
| <3000000 0>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys_default>; |
| |
| label = "GPIO Buttons"; |
| |
| button-volume-up { |
| label = "Volume Up"; |
| gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| }; |
| }; |
| |
| reg_ctp: regulator-ctp { |
| compatible = "regulator-fixed"; |
| regulator-name = "ctp"; |
| |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| |
| gpio = <&tlmm 17 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ctp_pwr_en_default>; |
| }; |
| |
| flash-led-controller { |
| compatible = "sgmicro,sgm3140"; |
| flash-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>; |
| enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&camera_flash_default>; |
| |
| flash_led: led { |
| function = LED_FUNCTION_FLASH; |
| color = <LED_COLOR_ID_WHITE>; |
| flash-max-timeout-us = <250000>; |
| }; |
| }; |
| }; |
| |
| &blsp_i2c1 { |
| status = "okay"; |
| |
| led-controller@45 { |
| compatible = "awinic,aw2013"; |
| reg = <0x45>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vcc-supply = <&pm8916_l17>; |
| vio-supply = <&pm8916_l6>; |
| |
| led@0 { |
| reg = <0>; |
| led-max-microamp = <5000>; |
| function = LED_FUNCTION_INDICATOR; |
| color = <LED_COLOR_ID_RED>; |
| }; |
| |
| led@1 { |
| reg = <1>; |
| led-max-microamp = <5000>; |
| function = LED_FUNCTION_INDICATOR; |
| color = <LED_COLOR_ID_GREEN>; |
| }; |
| |
| led@2 { |
| reg = <2>; |
| led-max-microamp = <5000>; |
| function = LED_FUNCTION_INDICATOR; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| }; |
| |
| &blsp_i2c2 { |
| status = "okay"; |
| |
| accelerometer@10 { |
| compatible = "bosch,bmc156_accel"; |
| reg = <0x10>; |
| |
| /* |
| * For some reason the interrupt line is usually not connected |
| * to the BMC156. However, there are two pads next to the chip |
| * that can be shorted to make it work if needed. |
| * |
| * interrupt-parent = <&tlmm>; |
| * interrupts = <116 IRQ_TYPE_EDGE_RISING>; |
| */ |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&accel_int_default>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vddio-supply = <&pm8916_l6>; |
| |
| mount-matrix = "0", "1", "0", |
| "-1", "0", "0", |
| "0", "0", "1"; |
| }; |
| |
| magnetometer@12 { |
| compatible = "bosch,bmc156_magn"; |
| reg = <0x12>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <113 IRQ_TYPE_EDGE_RISING>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&magn_int_default>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vddio-supply = <&pm8916_l6>; |
| }; |
| |
| light-sensor@23 { |
| compatible = "liteon,ltr559"; |
| reg = <0x23>; |
| proximity-near-level = <75>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <115 IRQ_TYPE_EDGE_FALLING>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&light_int_default>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vddio-supply = <&pm8916_l6>; |
| }; |
| |
| gyroscope@68 { |
| compatible = "bosch,bmg160"; |
| reg = <0x68>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <23 IRQ_TYPE_EDGE_RISING>, |
| <22 IRQ_TYPE_EDGE_RISING>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gyro_int_default>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vddio-supply = <&pm8916_l6>; |
| }; |
| }; |
| |
| &blsp_i2c5 { |
| status = "okay"; |
| |
| rmi4@20 { |
| compatible = "syna,rmi4-i2c"; |
| reg = <0x20>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <13 IRQ_TYPE_EDGE_FALLING>; |
| |
| vdd-supply = <®_ctp>; |
| vio-supply = <&pm8916_l6>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&tp_int_default>; |
| |
| syna,startup-delay-ms = <10>; |
| |
| rmi4-f01@1 { |
| reg = <0x1>; |
| syna,nosleep-mode = <1>; /* Allow sleeping */ |
| }; |
| |
| rmi4-f12@12 { |
| reg = <0x12>; |
| syna,sensor-type = <1>; /* Touchscreen */ |
| }; |
| }; |
| }; |
| |
| &blsp_uart2 { |
| status = "okay"; |
| }; |
| |
| &pm8916_bms { |
| status = "okay"; |
| |
| monitored-battery = <&battery>; |
| power-supplies = <&pm8916_charger>; |
| }; |
| |
| &pm8916_charger { |
| status = "okay"; |
| |
| monitored-battery = <&battery>; |
| |
| qcom,fast-charge-safe-current = <900000>; |
| qcom,fast-charge-safe-voltage = <4300000>; |
| }; |
| |
| &pm8916_codec { |
| qcom,micbias-lvl = <2800>; |
| qcom,mbhc-vthreshold-low = <75 150 237 450 500>; |
| qcom,mbhc-vthreshold-high = <75 150 237 450 500>; |
| qcom,hphl-jack-type-normally-open; |
| }; |
| |
| &pm8916_resin { |
| status = "okay"; |
| linux,code = <KEY_VOLUMEDOWN>; |
| }; |
| |
| &pm8916_rpm_regulators { |
| pm8916_l17: l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| }; |
| |
| &pm8916_vib { |
| status = "okay"; |
| }; |
| |
| &sdhc_1 { |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| status = "okay"; |
| non-removable; |
| }; |
| |
| &sound { |
| audio-routing = |
| "AMIC1", "MIC BIAS Internal1", |
| "AMIC2", "MIC BIAS Internal2", |
| "AMIC3", "MIC BIAS Internal3"; |
| }; |
| |
| &usb { |
| status = "okay"; |
| dr_mode = "peripheral"; |
| extcon = <&pm8916_charger>; |
| }; |
| |
| &usb_hs_phy { |
| extcon = <&pm8916_charger>; |
| }; |
| |
| &venus { |
| status = "okay"; |
| }; |
| |
| &venus_mem { |
| status = "okay"; |
| }; |
| |
| &wcnss { |
| status = "okay"; |
| }; |
| |
| &wcnss_iris { |
| compatible = "qcom,wcn3620"; |
| }; |
| |
| &wcnss_mem { |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| accel_int_default: accel-int-default-state { |
| pins = "gpio116"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| camera_flash_default: camera-flash-default-state { |
| pins = "gpio31", "gpio32"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| ctp_pwr_en_default: ctp-pwr-en-default-state { |
| pins = "gpio17"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| gpio_keys_default: gpio-keys-default-state { |
| pins = "gpio107"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| gyro_int_default: gyro-int-default-state { |
| pins = "gpio22", "gpio23"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| light_int_default: light-int-default-state { |
| pins = "gpio115"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| magn_int_default: magn-int-default-state { |
| pins = "gpio113"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| tp_int_default: tp-int-default-state { |
| pins = "gpio13"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
