| // SPDX-License-Identifier: GPL-2.0-only |
| /* Copyright (c) 2014, The Linux Foundation. All rights reserved. |
| */ |
| #include <linux/bits.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/platform_device.h> |
| #include <linux/watchdog.h> |
| #include <linux/of_device.h> |
| |
| enum wdt_reg { |
| WDT_RST, |
| WDT_EN, |
| WDT_STS, |
| WDT_BARK_TIME, |
| WDT_BITE_TIME, |
| }; |
| |
| #define QCOM_WDT_ENABLE BIT(0) |
| |
| static const u32 reg_offset_data_apcs_tmr[] = { |
| [WDT_RST] = 0x38, |
| [WDT_EN] = 0x40, |
| [WDT_STS] = 0x44, |
| [WDT_BARK_TIME] = 0x4C, |
| [WDT_BITE_TIME] = 0x5C, |
| }; |
| |
| static const u32 reg_offset_data_kpss[] = { |
| [WDT_RST] = 0x4, |
| [WDT_EN] = 0x8, |
| [WDT_STS] = 0xC, |
| [WDT_BARK_TIME] = 0x10, |
| [WDT_BITE_TIME] = 0x14, |
| }; |
| |
| struct qcom_wdt_match_data { |
| const u32 *offset; |
| bool pretimeout; |
| }; |
| |
| struct qcom_wdt { |
| struct watchdog_device wdd; |
| unsigned long rate; |
| void __iomem *base; |
| const u32 *layout; |
| }; |
| |
| static void __iomem *wdt_addr(struct qcom_wdt *wdt, enum wdt_reg reg) |
| { |
| return wdt->base + wdt->layout[reg]; |
| } |
| |
| static inline |
| struct qcom_wdt *to_qcom_wdt(struct watchdog_device *wdd) |
| { |
| return container_of(wdd, struct qcom_wdt, wdd); |
| } |
| |
| static irqreturn_t qcom_wdt_isr(int irq, void *arg) |
| { |
| struct watchdog_device *wdd = arg; |
| |
| watchdog_notify_pretimeout(wdd); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int qcom_wdt_start(struct watchdog_device *wdd) |
| { |
| struct qcom_wdt *wdt = to_qcom_wdt(wdd); |
| unsigned int bark = wdd->timeout - wdd->pretimeout; |
| |
| writel(0, wdt_addr(wdt, WDT_EN)); |
| writel(1, wdt_addr(wdt, WDT_RST)); |
| writel(bark * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME)); |
| writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME)); |
| writel(QCOM_WDT_ENABLE, wdt_addr(wdt, WDT_EN)); |
| return 0; |
| } |
| |
| static int qcom_wdt_stop(struct watchdog_device *wdd) |
| { |
| struct qcom_wdt *wdt = to_qcom_wdt(wdd); |
| |
| writel(0, wdt_addr(wdt, WDT_EN)); |
| return 0; |
| } |
| |
| static int qcom_wdt_ping(struct watchdog_device *wdd) |
| { |
| struct qcom_wdt *wdt = to_qcom_wdt(wdd); |
| |
| writel(1, wdt_addr(wdt, WDT_RST)); |
| return 0; |
| } |
| |
| static int qcom_wdt_set_timeout(struct watchdog_device *wdd, |
| unsigned int timeout) |
| { |
| wdd->timeout = timeout; |
| return qcom_wdt_start(wdd); |
| } |
| |
| static int qcom_wdt_set_pretimeout(struct watchdog_device *wdd, |
| unsigned int timeout) |
| { |
| wdd->pretimeout = timeout; |
| return qcom_wdt_start(wdd); |
| } |
| |
| static int qcom_wdt_restart(struct watchdog_device *wdd, unsigned long action, |
| void *data) |
| { |
| struct qcom_wdt *wdt = to_qcom_wdt(wdd); |
| u32 timeout; |
| |
| /* |
| * Trigger watchdog bite: |
| * Setup BITE_TIME to be 128ms, and enable WDT. |
| */ |
| timeout = 128 * wdt->rate / 1000; |
| |
| writel(0, wdt_addr(wdt, WDT_EN)); |
| writel(1, wdt_addr(wdt, WDT_RST)); |
| writel(timeout, wdt_addr(wdt, WDT_BARK_TIME)); |
| writel(timeout, wdt_addr(wdt, WDT_BITE_TIME)); |
| writel(QCOM_WDT_ENABLE, wdt_addr(wdt, WDT_EN)); |
| |
| /* |
| * Actually make sure the above sequence hits hardware before sleeping. |
| */ |
| wmb(); |
| |
| mdelay(150); |
| return 0; |
| } |
| |
| static int qcom_wdt_is_running(struct watchdog_device *wdd) |
| { |
| struct qcom_wdt *wdt = to_qcom_wdt(wdd); |
| |
| return (readl(wdt_addr(wdt, WDT_EN)) & QCOM_WDT_ENABLE); |
| } |
| |
| static const struct watchdog_ops qcom_wdt_ops = { |
| .start = qcom_wdt_start, |
| .stop = qcom_wdt_stop, |
| .ping = qcom_wdt_ping, |
| .set_timeout = qcom_wdt_set_timeout, |
| .set_pretimeout = qcom_wdt_set_pretimeout, |
| .restart = qcom_wdt_restart, |
| .owner = THIS_MODULE, |
| }; |
| |
| static const struct watchdog_info qcom_wdt_info = { |
| .options = WDIOF_KEEPALIVEPING |
| | WDIOF_MAGICCLOSE |
| | WDIOF_SETTIMEOUT |
| | WDIOF_CARDRESET, |
| .identity = KBUILD_MODNAME, |
| }; |
| |
| static const struct watchdog_info qcom_wdt_pt_info = { |
| .options = WDIOF_KEEPALIVEPING |
| | WDIOF_MAGICCLOSE |
| | WDIOF_SETTIMEOUT |
| | WDIOF_PRETIMEOUT |
| | WDIOF_CARDRESET, |
| .identity = KBUILD_MODNAME, |
| }; |
| |
| static void qcom_clk_disable_unprepare(void *data) |
| { |
| clk_disable_unprepare(data); |
| } |
| |
| static const struct qcom_wdt_match_data match_data_apcs_tmr = { |
| .offset = reg_offset_data_apcs_tmr, |
| .pretimeout = false, |
| }; |
| |
| static const struct qcom_wdt_match_data match_data_kpss = { |
| .offset = reg_offset_data_kpss, |
| .pretimeout = true, |
| }; |
| |
| static int qcom_wdt_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct qcom_wdt *wdt; |
| struct resource *res; |
| struct device_node *np = dev->of_node; |
| const struct qcom_wdt_match_data *data; |
| u32 percpu_offset; |
| int irq, ret; |
| struct clk *clk; |
| |
| data = of_device_get_match_data(dev); |
| if (!data) { |
| dev_err(dev, "Unsupported QCOM WDT module\n"); |
| return -ENODEV; |
| } |
| |
| wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL); |
| if (!wdt) |
| return -ENOMEM; |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| if (!res) |
| return -ENOMEM; |
| |
| /* We use CPU0's DGT for the watchdog */ |
| if (of_property_read_u32(np, "cpu-offset", &percpu_offset)) |
| percpu_offset = 0; |
| |
| res->start += percpu_offset; |
| res->end += percpu_offset; |
| |
| wdt->base = devm_ioremap_resource(dev, res); |
| if (IS_ERR(wdt->base)) |
| return PTR_ERR(wdt->base); |
| |
| clk = devm_clk_get(dev, NULL); |
| if (IS_ERR(clk)) { |
| dev_err(dev, "failed to get input clock\n"); |
| return PTR_ERR(clk); |
| } |
| |
| ret = clk_prepare_enable(clk); |
| if (ret) { |
| dev_err(dev, "failed to setup clock\n"); |
| return ret; |
| } |
| ret = devm_add_action_or_reset(dev, qcom_clk_disable_unprepare, clk); |
| if (ret) |
| return ret; |
| |
| /* |
| * We use the clock rate to calculate the max timeout, so ensure it's |
| * not zero to avoid a divide-by-zero exception. |
| * |
| * WATCHDOG_CORE assumes units of seconds, if the WDT is clocked such |
| * that it would bite before a second elapses it's usefulness is |
| * limited. Bail if this is the case. |
| */ |
| wdt->rate = clk_get_rate(clk); |
| if (wdt->rate == 0 || |
| wdt->rate > 0x10000000U) { |
| dev_err(dev, "invalid clock rate\n"); |
| return -EINVAL; |
| } |
| |
| /* check if there is pretimeout support */ |
| irq = platform_get_irq_optional(pdev, 0); |
| if (data->pretimeout && irq > 0) { |
| ret = devm_request_irq(dev, irq, qcom_wdt_isr, 0, |
| "wdt_bark", &wdt->wdd); |
| if (ret) |
| return ret; |
| |
| wdt->wdd.info = &qcom_wdt_pt_info; |
| wdt->wdd.pretimeout = 1; |
| } else { |
| if (irq == -EPROBE_DEFER) |
| return -EPROBE_DEFER; |
| |
| wdt->wdd.info = &qcom_wdt_info; |
| } |
| |
| wdt->wdd.ops = &qcom_wdt_ops; |
| wdt->wdd.min_timeout = 1; |
| wdt->wdd.max_timeout = 0x10000000U / wdt->rate; |
| wdt->wdd.parent = dev; |
| wdt->layout = data->offset; |
| |
| if (readl(wdt_addr(wdt, WDT_STS)) & 1) |
| wdt->wdd.bootstatus = WDIOF_CARDRESET; |
| |
| /* |
| * If 'timeout-sec' unspecified in devicetree, assume a 30 second |
| * default, unless the max timeout is less than 30 seconds, then use |
| * the max instead. |
| */ |
| wdt->wdd.timeout = min(wdt->wdd.max_timeout, 30U); |
| watchdog_init_timeout(&wdt->wdd, 0, dev); |
| |
| /* |
| * If WDT is already running, call WDT start which |
| * will stop the WDT, set timeouts as bootloader |
| * might use different ones and set running bit |
| * to inform the WDT subsystem to ping the WDT |
| */ |
| if (qcom_wdt_is_running(&wdt->wdd)) { |
| qcom_wdt_start(&wdt->wdd); |
| set_bit(WDOG_HW_RUNNING, &wdt->wdd.status); |
| } |
| |
| ret = devm_watchdog_register_device(dev, &wdt->wdd); |
| if (ret) |
| return ret; |
| |
| platform_set_drvdata(pdev, wdt); |
| return 0; |
| } |
| |
| static int __maybe_unused qcom_wdt_suspend(struct device *dev) |
| { |
| struct qcom_wdt *wdt = dev_get_drvdata(dev); |
| |
| if (watchdog_active(&wdt->wdd)) |
| qcom_wdt_stop(&wdt->wdd); |
| |
| return 0; |
| } |
| |
| static int __maybe_unused qcom_wdt_resume(struct device *dev) |
| { |
| struct qcom_wdt *wdt = dev_get_drvdata(dev); |
| |
| if (watchdog_active(&wdt->wdd)) |
| qcom_wdt_start(&wdt->wdd); |
| |
| return 0; |
| } |
| |
| static SIMPLE_DEV_PM_OPS(qcom_wdt_pm_ops, qcom_wdt_suspend, qcom_wdt_resume); |
| |
| static const struct of_device_id qcom_wdt_of_table[] = { |
| { .compatible = "qcom,kpss-timer", .data = &match_data_apcs_tmr }, |
| { .compatible = "qcom,scss-timer", .data = &match_data_apcs_tmr }, |
| { .compatible = "qcom,kpss-wdt", .data = &match_data_kpss }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, qcom_wdt_of_table); |
| |
| static struct platform_driver qcom_watchdog_driver = { |
| .probe = qcom_wdt_probe, |
| .driver = { |
| .name = KBUILD_MODNAME, |
| .of_match_table = qcom_wdt_of_table, |
| .pm = &qcom_wdt_pm_ops, |
| }, |
| }; |
| module_platform_driver(qcom_watchdog_driver); |
| |
| MODULE_DESCRIPTION("QCOM KPSS Watchdog Driver"); |
| MODULE_LICENSE("GPL v2"); |