| config MTD_NAND_ECC |
| tristate |
| |
| config MTD_NAND_ECC_SMC |
| bool "NAND ECC Smart Media byte order" |
| depends on MTD_NAND_ECC |
| default n |
| help |
| Software ECC according to the Smart Media Specification. |
| The original Linux implementation had byte 0 and 1 swapped. |
| |
| |
| menuconfig MTD_NAND |
| tristate "Raw/Parallel NAND Device Support" |
| depends on MTD |
| select MTD_NAND_ECC |
| help |
| This enables support for accessing all type of raw/parallel |
| NAND flash devices. For further information see |
| <http://www.linux-mtd.infradead.org/doc/nand.html>. |
| |
| if MTD_NAND |
| |
| config MTD_NAND_BCH |
| tristate |
| select BCH |
| depends on MTD_NAND_ECC_BCH |
| default MTD_NAND |
| |
| config MTD_NAND_ECC_BCH |
| bool "Support software BCH ECC" |
| default n |
| help |
| This enables support for software BCH error correction. Binary BCH |
| codes are more powerful and cpu intensive than traditional Hamming |
| ECC codes. They are used with NAND devices requiring more than 1 bit |
| of error correction. |
| |
| config MTD_SM_COMMON |
| tristate |
| default n |
| |
| config MTD_NAND_DENALI |
| tristate |
| |
| config MTD_NAND_DENALI_PCI |
| tristate "Support Denali NAND controller on Intel Moorestown" |
| select MTD_NAND_DENALI |
| depends on PCI |
| help |
| Enable the driver for NAND flash on Intel Moorestown, using the |
| Denali NAND controller core. |
| |
| config MTD_NAND_DENALI_DT |
| tristate "Support Denali NAND controller as a DT device" |
| select MTD_NAND_DENALI |
| depends on HAS_DMA && HAVE_CLK && OF |
| help |
| Enable the driver for NAND flash on platforms using a Denali NAND |
| controller as a DT device. |
| |
| config MTD_NAND_GPIO |
| tristate "GPIO assisted NAND Flash driver" |
| depends on GPIOLIB || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| This enables a NAND flash driver where control signals are |
| connected to GPIO pins, and commands and data are communicated |
| via a memory mapped interface. |
| |
| config MTD_NAND_AMS_DELTA |
| tristate "NAND Flash device on Amstrad E3" |
| depends on MACH_AMS_DELTA |
| default y |
| help |
| Support for NAND flash on Amstrad E3 (Delta). |
| |
| config MTD_NAND_OMAP2 |
| tristate "NAND Flash device on OMAP2, OMAP3, OMAP4 and Keystone" |
| depends on ARCH_OMAP2PLUS || ARCH_KEYSTONE || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Support for NAND flash on Texas Instruments OMAP2, OMAP3, OMAP4 |
| and Keystone platforms. |
| |
| config MTD_NAND_OMAP_BCH |
| depends on MTD_NAND_OMAP2 |
| bool "Support hardware based BCH error correction" |
| default n |
| select BCH |
| help |
| This config enables the ELM hardware engine, which can be used to |
| locate and correct errors when using BCH ECC scheme. This offloads |
| the cpu from doing ECC error searching and correction. However some |
| legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine |
| so this is optional for them. |
| |
| config MTD_NAND_OMAP_BCH_BUILD |
| def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH |
| |
| config MTD_NAND_RICOH |
| tristate "Ricoh xD card reader" |
| default n |
| depends on PCI |
| select MTD_SM_COMMON |
| help |
| Enable support for Ricoh R5C852 xD card reader |
| You also need to enable ether |
| NAND SSFDC (SmartMedia) read only translation layer' or new |
| expermental, readwrite |
| 'SmartMedia/xD new translation layer' |
| |
| config MTD_NAND_AU1550 |
| tristate "Au1550/1200 NAND support" |
| depends on MIPS_ALCHEMY |
| help |
| This enables the driver for the NAND flash controller on the |
| AMD/Alchemy 1550 SOC. |
| |
| config MTD_NAND_S3C2410 |
| tristate "NAND Flash support for Samsung S3C SoCs" |
| depends on ARCH_S3C24XX || ARCH_S3C64XX |
| help |
| This enables the NAND flash controller on the S3C24xx and S3C64xx |
| SoCs |
| |
| No board specific support is done by this driver, each board |
| must advertise a platform_device for the driver to attach. |
| |
| config MTD_NAND_S3C2410_DEBUG |
| bool "Samsung S3C NAND driver debug" |
| depends on MTD_NAND_S3C2410 |
| help |
| Enable debugging of the S3C NAND driver |
| |
| config MTD_NAND_NDFC |
| tristate "NDFC NanD Flash Controller" |
| depends on 4xx |
| select MTD_NAND_ECC_SMC |
| help |
| NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs |
| |
| config MTD_NAND_S3C2410_CLKSTOP |
| bool "Samsung S3C NAND IDLE clock stop" |
| depends on MTD_NAND_S3C2410 |
| default n |
| help |
| Stop the clock to the NAND controller when there is no chip |
| selected to save power. This will mean there is a small delay |
| when the is NAND chip selected or released, but will save |
| approximately 5mA of power when there is nothing happening. |
| |
| config MTD_NAND_TANGO |
| tristate "NAND Flash support for Tango chips" |
| depends on ARCH_TANGO || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Enables the NAND Flash controller on Tango chips. |
| |
| config MTD_NAND_DISKONCHIP |
| tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)" |
| depends on HAS_IOMEM |
| select REED_SOLOMON |
| select REED_SOLOMON_DEC16 |
| help |
| This is a reimplementation of M-Systems DiskOnChip 2000, |
| Millennium and Millennium Plus as a standard NAND device driver, |
| as opposed to the earlier self-contained MTD device drivers. |
| This should enable, among other things, proper JFFS2 operation on |
| these devices. |
| |
| config MTD_NAND_DISKONCHIP_PROBE_ADVANCED |
| bool "Advanced detection options for DiskOnChip" |
| depends on MTD_NAND_DISKONCHIP |
| help |
| This option allows you to specify nonstandard address at which to |
| probe for a DiskOnChip, or to change the detection options. You |
| are unlikely to need any of this unless you are using LinuxBIOS. |
| Say 'N'. |
| |
| config MTD_NAND_DISKONCHIP_PROBE_ADDRESS |
| hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED |
| depends on MTD_NAND_DISKONCHIP |
| default "0" |
| help |
| By default, the probe for DiskOnChip devices will look for a |
| DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. |
| This option allows you to specify a single address at which to probe |
| for the device, which is useful if you have other devices in that |
| range which get upset when they are probed. |
| |
| (Note that on PowerPC, the normal probe will only check at |
| 0xE4000000.) |
| |
| Normally, you should leave this set to zero, to allow the probe at |
| the normal addresses. |
| |
| config MTD_NAND_DISKONCHIP_PROBE_HIGH |
| bool "Probe high addresses" |
| depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED |
| help |
| By default, the probe for DiskOnChip devices will look for a |
| DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. |
| This option changes to make it probe between 0xFFFC8000 and |
| 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be |
| useful to you. Say 'N'. |
| |
| config MTD_NAND_DISKONCHIP_BBTWRITE |
| bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP" |
| depends on MTD_NAND_DISKONCHIP |
| help |
| On DiskOnChip devices shipped with the INFTL filesystem (Millennium |
| and 2000 TSOP/Alon), Linux reserves some space at the end of the |
| device for the Bad Block Table (BBT). If you have existing INFTL |
| data on your device (created by non-Linux tools such as M-Systems' |
| DOS drivers), your data might overlap the area Linux wants to use for |
| the BBT. If this is a concern for you, leave this option disabled and |
| Linux will not write BBT data into this area. |
| The downside of leaving this option disabled is that if bad blocks |
| are detected by Linux, they will not be recorded in the BBT, which |
| could cause future problems. |
| Once you enable this option, new filesystems (INFTL or others, created |
| in Linux or other operating systems) will not use the reserved area. |
| The only reason not to enable this option is to prevent damage to |
| preexisting filesystems. |
| Even if you leave this disabled, you can enable BBT writes at module |
| load time (assuming you build diskonchip as a module) with the module |
| parameter "inftl_bbt_write=1". |
| |
| config MTD_NAND_SHARPSL |
| tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)" |
| depends on ARCH_PXA || COMPILE_TEST |
| depends on HAS_IOMEM |
| |
| config MTD_NAND_CAFE |
| tristate "NAND support for OLPC CAFÉ chip" |
| depends on PCI |
| select REED_SOLOMON |
| select REED_SOLOMON_DEC16 |
| help |
| Use NAND flash attached to the CAFÉ chip designed for the OLPC |
| laptop. |
| |
| config MTD_NAND_CS553X |
| tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)" |
| depends on X86_32 |
| depends on !UML && HAS_IOMEM |
| help |
| The CS553x companion chips for the AMD Geode processor |
| include NAND flash controllers with built-in hardware ECC |
| capabilities; enabling this option will allow you to use |
| these. The driver will check the MSRs to verify that the |
| controller is enabled for NAND, and currently requires that |
| the controller be in MMIO mode. |
| |
| If you say "m", the module will be called cs553x_nand. |
| |
| config MTD_NAND_ATMEL |
| tristate "Support for NAND Flash / SmartMedia on AT91" |
| depends on ARCH_AT91 || COMPILE_TEST |
| depends on HAS_IOMEM |
| select GENERIC_ALLOCATOR |
| select MFD_ATMEL_SMC |
| help |
| Enables support for NAND Flash / Smart Media Card interface |
| on Atmel AT91 processors. |
| |
| config MTD_NAND_MARVELL |
| tristate "NAND controller support on Marvell boards" |
| depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \ |
| COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| This enables the NAND flash controller driver for Marvell boards, |
| including: |
| - PXA3xx processors (NFCv1) |
| - 32-bit Armada platforms (XP, 37x, 38x, 39x) (NFCv2) |
| - 64-bit Aramda platforms (7k, 8k) (NFCv2) |
| |
| config MTD_NAND_SLC_LPC32XX |
| tristate "NXP LPC32xx SLC Controller" |
| depends on ARCH_LPC32XX || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell |
| chips) NAND controller. This is the default for the PHYTEC 3250 |
| reference board which contains a NAND256R3A2CZA6 chip. |
| |
| Please check the actual NAND chip connected and its support |
| by the SLC NAND controller. |
| |
| config MTD_NAND_MLC_LPC32XX |
| tristate "NXP LPC32xx MLC Controller" |
| depends on ARCH_LPC32XX || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND |
| controller. This is the default for the WORK92105 controller |
| board. |
| |
| Please check the actual NAND chip connected and its support |
| by the MLC NAND controller. |
| |
| config MTD_NAND_CM_X270 |
| tristate "Support for NAND Flash on CM-X270 modules" |
| depends on MACH_ARMCORE |
| |
| config MTD_NAND_PASEMI |
| tristate "NAND support for PA Semi PWRficient" |
| depends on PPC_PASEMI |
| help |
| Enables support for NAND Flash interface on PA Semi PWRficient |
| based boards |
| |
| config MTD_NAND_TMIO |
| tristate "NAND Flash device on Toshiba Mobile IO Controller" |
| depends on MFD_TMIO |
| help |
| Support for NAND flash connected to a Toshiba Mobile IO |
| Controller in some PDAs, including the Sharp SL6000x. |
| |
| config MTD_NAND_NANDSIM |
| tristate "Support for NAND Flash Simulator" |
| help |
| The simulator may simulate various NAND flash chips for the |
| MTD nand layer. |
| |
| config MTD_NAND_GPMI_NAND |
| tristate "GPMI NAND Flash Controller driver" |
| depends on MXS_DMA |
| help |
| Enables NAND Flash support for IMX23, IMX28 or IMX6. |
| The GPMI controller is very powerful, with the help of BCH |
| module, it can do the hardware ECC. The GPMI supports several |
| NAND flashs at the same time. |
| |
| config MTD_NAND_BRCMNAND |
| tristate "Broadcom STB NAND controller" |
| depends on ARM || ARM64 || MIPS || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Enables the Broadcom NAND controller driver. The controller was |
| originally designed for Set-Top Box but is used on various BCM7xxx, |
| BCM3xxx, BCM63xxx, iProc/Cygnus and more. |
| |
| config MTD_NAND_BCM47XXNFLASH |
| tristate "Support for NAND flash on BCM4706 BCMA bus" |
| depends on BCMA_NFLASH |
| depends on BCMA |
| help |
| BCMA bus can have various flash memories attached, they are |
| registered by bcma as platform devices. This enables driver for |
| NAND flash memories. For now only BCM4706 is supported. |
| |
| config MTD_NAND_PLATFORM |
| tristate "Support for generic platform NAND driver" |
| depends on HAS_IOMEM |
| help |
| This implements a generic NAND driver for on-SOC platform |
| devices. You will need to provide platform-specific functions |
| via platform_data. |
| |
| config MTD_NAND_ORION |
| tristate "NAND Flash support for Marvell Orion SoC" |
| depends on PLAT_ORION |
| help |
| This enables the NAND flash controller on Orion machines. |
| |
| No board specific support is done by this driver, each board |
| must advertise a platform_device for the driver to attach. |
| |
| config MTD_NAND_OXNAS |
| tristate "NAND Flash support for Oxford Semiconductor SoC" |
| depends on ARCH_OXNAS || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| This enables the NAND flash controller on Oxford Semiconductor SoCs. |
| |
| config MTD_NAND_FSL_ELBC |
| tristate "NAND support for Freescale eLBC controllers" |
| depends on FSL_SOC |
| select FSL_LBC |
| help |
| Various Freescale chips, including the 8313, include a NAND Flash |
| Controller Module with built-in hardware ECC capabilities. |
| Enabling this option will enable you to use this to control |
| external NAND devices. |
| |
| config MTD_NAND_FSL_IFC |
| tristate "NAND support for Freescale IFC controller" |
| depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A || COMPILE_TEST |
| depends on HAS_IOMEM |
| select FSL_IFC |
| select MEMORY |
| help |
| Various Freescale chips e.g P1010, include a NAND Flash machine |
| with built-in hardware ECC capabilities. |
| Enabling this option will enable you to use this to control |
| external NAND devices. |
| |
| config MTD_NAND_FSL_UPM |
| tristate "Support for NAND on Freescale UPM" |
| depends on PPC_83xx || PPC_85xx |
| select FSL_LBC |
| help |
| Enables support for NAND Flash chips wired onto Freescale PowerPC |
| processor localbus with User-Programmable Machine support. |
| |
| config MTD_NAND_MPC5121_NFC |
| tristate "MPC5121 built-in NAND Flash Controller support" |
| depends on PPC_MPC512x |
| help |
| This enables the driver for the NAND flash controller on the |
| MPC5121 SoC. |
| |
| config MTD_NAND_VF610_NFC |
| tristate "Support for Freescale NFC for VF610/MPC5125" |
| depends on (SOC_VF610 || COMPILE_TEST) |
| depends on HAS_IOMEM |
| help |
| Enables support for NAND Flash Controller on some Freescale |
| processors like the VF610, MPC5125, MCF54418 or Kinetis K70. |
| The driver supports a maximum 2k page size. With 2k pages and |
| 64 bytes or more of OOB, hardware ECC with up to 32-bit error |
| correction is supported. Hardware ECC is only enabled through |
| device tree. |
| |
| config MTD_NAND_MXC |
| tristate "MXC NAND support" |
| depends on ARCH_MXC || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| This enables the driver for the NAND flash controller on the |
| MXC processors. |
| |
| config MTD_NAND_SH_FLCTL |
| tristate "Support for NAND on Renesas SuperH FLCTL" |
| depends on SUPERH || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Several Renesas SuperH CPU has FLCTL. This option enables support |
| for NAND Flash using FLCTL. |
| |
| config MTD_NAND_DAVINCI |
| tristate "Support NAND on DaVinci/Keystone SoC" |
| depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF) || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Enable the driver for NAND flash chips on Texas Instruments |
| DaVinci/Keystone processors. |
| |
| config MTD_NAND_TXX9NDFMC |
| tristate "NAND Flash support for TXx9 SoC" |
| depends on SOC_TX4938 || SOC_TX4939 || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| This enables the NAND flash controller on the TXx9 SoCs. |
| |
| config MTD_NAND_SOCRATES |
| tristate "Support for NAND on Socrates board" |
| depends on SOCRATES |
| help |
| Enables support for NAND Flash chips wired onto Socrates board. |
| |
| config MTD_NAND_NUC900 |
| tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards." |
| depends on ARCH_W90X900 || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| This enables the driver for the NAND Flash on evaluation board based |
| on w90p910 / NUC9xx. |
| |
| config MTD_NAND_JZ4740 |
| tristate "Support for JZ4740 SoC NAND controller" |
| depends on MACH_JZ4740 || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Enables support for NAND Flash on JZ4740 SoC based boards. |
| |
| config MTD_NAND_JZ4780 |
| tristate "Support for NAND on JZ4780 SoC" |
| depends on JZ4780_NEMC |
| help |
| Enables support for NAND Flash connected to the NEMC on JZ4780 SoC |
| based boards, using the BCH controller for hardware error correction. |
| |
| config MTD_NAND_FSMC |
| tristate "Support for NAND on ST Micros FSMC" |
| depends on OF && HAS_IOMEM |
| depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300 || \ |
| COMPILE_TEST |
| help |
| Enables support for NAND Flash chips on the ST Microelectronics |
| Flexible Static Memory Controller (FSMC) |
| |
| config MTD_NAND_XWAY |
| bool "Support for NAND on Lantiq XWAY SoC" |
| depends on LANTIQ && SOC_TYPE_XWAY |
| help |
| Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached |
| to the External Bus Unit (EBU). |
| |
| config MTD_NAND_SUNXI |
| tristate "Support for NAND on Allwinner SoCs" |
| depends on ARCH_SUNXI || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Enables support for NAND Flash chips on Allwinner SoCs. |
| |
| config MTD_NAND_HISI504 |
| tristate "Support for NAND controller on Hisilicon SoC Hip04" |
| depends on ARCH_HISI || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Enables support for NAND controller on Hisilicon SoC Hip04. |
| |
| config MTD_NAND_QCOM |
| tristate "Support for NAND on QCOM SoCs" |
| depends on ARCH_QCOM || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Enables support for NAND flash chips on SoCs containing the EBI2 NAND |
| controller. This controller is found on IPQ806x SoC. |
| |
| config MTD_NAND_MTK |
| tristate "Support for NAND controller on MTK SoCs" |
| depends on ARCH_MEDIATEK || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Enables support for NAND controller on MTK SoCs. |
| This controller is found on mt27xx, mt81xx, mt65xx SoCs. |
| |
| config MTD_NAND_TEGRA |
| tristate "Support for NAND controller on NVIDIA Tegra" |
| depends on ARCH_TEGRA || COMPILE_TEST |
| depends on HAS_IOMEM |
| help |
| Enables support for NAND flash controller on NVIDIA Tegra SoC. |
| The driver has been developed and tested on a Tegra 2 SoC. DMA |
| support, raw read/write page as well as HW ECC read/write page |
| is supported. Extra OOB bytes when using HW ECC are currently |
| not supported. |
| |
| endif # MTD_NAND |