drivers/block/Kconfig - linux - Git at Google

 # SPDX-License-Identifier: GPL-2.0
 #
 # Block device driver configuration
 #

 menuconfig BLK_DEV
 	bool "Block devices"
 	depends on BLOCK
 	default y
 	help
 	  Say Y here to get to see options for various different block device
 	  drivers. This option alone does not add any kernel code.

 	  If you say N, all options in this submenu will be skipped and disabled;
 	  only do this if you know what you are doing.

 if BLK_DEV

 source "drivers/block/null_blk/Kconfig"

 config BLK_DEV_FD
 	tristate "Normal floppy disk support"
 	depends on ARCH_MAY_HAVE_PC_FDC
 	help
 	  If you want to use the floppy disk drive(s) of your PC under Linux,
 	  say Y. Information about this driver, especially important for IBM
 	  Thinkpad users, is contained in
 	  <file:Documentation/admin-guide/blockdev/floppy.rst>.
 	  That file also contains the location of the Floppy driver FAQ as
 	  well as location of the fdutils package used to configure additional
 	  parameters of the driver at run time.

 	  To compile this driver as a module, choose M here: the
 	  module will be called floppy.

 config BLK_DEV_FD_RAWCMD
 	bool "Support for raw floppy disk commands (DEPRECATED)"
 	depends on BLK_DEV_FD
 	help
 	  If you want to use actual physical floppies and expect to do
 	  special low-level hardware accesses to them (access and use
 	  non-standard formats, for example), then enable this.

 	  Note that the code enabled by this option is rarely used and
 	  might be unstable or insecure, and distros should not enable it.

 	  Note: FDRAWCMD is deprecated and will be removed from the kernel
 	  in the near future.

 	  If unsure, say N.

 config AMIGA_FLOPPY
 	tristate "Amiga floppy support"
 	depends on AMIGA

 config ATARI_FLOPPY
 	tristate "Atari floppy support"
 	depends on ATARI

 config MAC_FLOPPY
 	tristate "Support for PowerMac floppy"
 	depends on PPC_PMAC && !PPC_PMAC64
 	help
 	  If you have a SWIM-3 (Super Woz Integrated Machine 3; from Apple)
 	  floppy controller, say Y here. Most commonly found in PowerMacs.

 config BLK_DEV_SWIM
 	tristate "Support for SWIM Macintosh floppy"
 	depends on M68K && MAC && !HIGHMEM
 	help
 	  You should select this option if you want floppy support
 	  and you don't have a II, IIfx, Q900, Q950 or AV series.

 config AMIGA_Z2RAM
 	tristate "Amiga Zorro II ramdisk support"
 	depends on ZORRO
 	help
 	  This enables support for using Chip RAM and Zorro II RAM as a
 	  ramdisk or as a swap partition. Say Y if you want to include this
 	  driver in the kernel.

 	  To compile this driver as a module, choose M here: the
 	  module will be called z2ram.

 config N64CART
 	bool "N64 cart support"
 	depends on MACH_NINTENDO64
 	help
 	  Support for the N64 cart.

 config CDROM
 	tristate

 config GDROM
 	tristate "SEGA Dreamcast GD-ROM drive"
 	depends on SH_DREAMCAST
 	select CDROM
 	help
 	  A standard SEGA Dreamcast comes with a modified CD ROM drive called a
 	  "GD-ROM" by SEGA to signify it is capable of reading special disks
 	  with up to 1 GB of data. This drive will also read standard CD ROM
 	  disks. Select this option to access any disks in your GD ROM drive.
 	  Most users will want to say "Y" here.
 	  You can also build this as a module which will be called gdrom.

 source "drivers/block/mtip32xx/Kconfig"

 source "drivers/block/zram/Kconfig"

 config BLK_DEV_UBD
 	bool "Virtual block device"
 	depends on UML
 	help
           The User-Mode Linux port includes a driver called UBD which will let
           you access arbitrary files on the host computer as block devices.
           Unless you know that you do not need such virtual block devices say
           Y here.

 config BLK_DEV_UBD_SYNC
 	bool "Always do synchronous disk IO for UBD"
 	depends on BLK_DEV_UBD
 	help
 	  Writes to the virtual block device are not immediately written to the
 	  host's disk; this may cause problems if, for example, the User-Mode
 	  Linux 'Virtual Machine' uses a journalling filesystem and the host
 	  computer crashes.

           Synchronous operation (i.e. always writing data to the host's disk
           immediately) is configurable on a per-UBD basis by using a special
           kernel command line option.  Alternatively, you can say Y here to
           turn on synchronous operation by default for all block devices.

           If you're running a journalling file system (like reiserfs, for
           example) in your virtual machine, you will want to say Y here.  If
           you care for the safety of the data in your virtual machine, Y is a
           wise choice too.  In all other cases (for example, if you're just
           playing around with User-Mode Linux) you can choose N.

 config BLK_DEV_COW_COMMON
 	bool
 	default BLK_DEV_UBD

 config BLK_DEV_LOOP
 	tristate "Loopback device support"
 	help
 	  Saying Y here will allow you to use a regular file as a block
 	  device; you can then create a file system on that block device and
 	  mount it just as you would mount other block devices such as hard
 	  drive partitions, CD-ROM drives or floppy drives. The loop devices
 	  are block special device files with major number 7 and typically
 	  called /dev/loop0, /dev/loop1 etc.

 	  This is useful if you want to check an ISO 9660 file system before
 	  burning the CD, or if you want to use floppy images without first
 	  writing them to floppy. Furthermore, some Linux distributions avoid
 	  the need for a dedicated Linux partition by keeping their complete
 	  root file system inside a DOS FAT file using this loop device
 	  driver.

 	  To use the loop device, you need the losetup utility, found in the
 	  util-linux package, see
 	  <https://www.kernel.org/pub/linux/utils/util-linux/>.

 	  The loop device driver can also be used to "hide" a file system in
 	  a disk partition, floppy, or regular file, either using encryption
 	  (scrambling the data) or steganography (hiding the data in the low
 	  bits of, say, a sound file). This is also safe if the file resides
 	  on a remote file server.

 	  Note that this loop device has nothing to do with the loopback
 	  device used for network connections from the machine to itself.

 	  To compile this driver as a module, choose M here: the
 	  module will be called loop.

 	  Most users will answer N here.

 config BLK_DEV_LOOP_MIN_COUNT
 	int "Number of loop devices to pre-create at init time"
 	depends on BLK_DEV_LOOP
 	default 8
 	help
 	  Static number of loop devices to be unconditionally pre-created
 	  at init time.

 	  This default value can be overwritten on the kernel command
 	  line or with module-parameter loop.max_loop.

 	  The historic default is 8. If a late 2011 version of losetup(8)
 	  is used, it can be set to 0, since needed loop devices can be
 	  dynamically allocated with the /dev/loop-control interface.

 source "drivers/block/drbd/Kconfig"

 config BLK_DEV_NBD
 	tristate "Network block device support"
 	depends on NET
 	help
 	  Saying Y here will allow your computer to be a client for network
 	  block devices, i.e. it will be able to use block devices exported by
 	  servers (mount file systems on them etc.). Communication between
 	  client and server works over TCP/IP networking, but to the client
 	  program this is hidden: it looks like a regular local file access to
 	  a block device special file such as /dev/nd0.

 	  Network block devices also allows you to run a block-device in
 	  userland (making server and client physically the same computer,
 	  communicating using the loopback network device).

 	  Read <file:Documentation/admin-guide/blockdev/nbd.rst> for more information,
 	  especially about where to find the server code, which runs in user
 	  space and does not need special kernel support.

 	  Note that this has nothing to do with the network file systems NFS
 	  or Coda; you can say N here even if you intend to use NFS or Coda.

 	  To compile this driver as a module, choose M here: the
 	  module will be called nbd.

 	  If unsure, say N.

 config BLK_DEV_RAM
 	tristate "RAM block device support"
 	help
 	  Saying Y here will allow you to use a portion of your RAM memory as
 	  a block device, so that you can make file systems on it, read and
 	  write to it and do all the other things that you can do with normal
 	  block devices (such as hard drives). It is usually used to load and
 	  store a copy of a minimal root file system off of a floppy into RAM
 	  during the initial install of Linux.

 	  Note that the kernel command line option "ramdisk=XX" is now obsolete.
 	  For details, read <file:Documentation/admin-guide/blockdev/ramdisk.rst>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called brd. An alias "rd" has been defined
 	  for historical reasons.

 	  Most normal users won't need the RAM disk functionality, and can
 	  thus say N here.

 config BLK_DEV_RAM_COUNT
 	int "Default number of RAM disks"
 	default "16"
 	depends on BLK_DEV_RAM
 	help
 	  The default value is 16 RAM disks. Change this if you know what you
 	  are doing. If you boot from a filesystem that needs to be extracted
 	  in memory, you will need at least one RAM disk (e.g. root on cramfs).

 config BLK_DEV_RAM_SIZE
 	int "Default RAM disk size (kbytes)"
 	depends on BLK_DEV_RAM
 	default "4096"
 	help
 	  The default value is 4096 kilobytes. Only change this if you know
 	  what you are doing.

 config CDROM_PKTCDVD
 	tristate "Packet writing on CD/DVD media (DEPRECATED)"
 	depends on !UML
 	depends on SCSI
 	select CDROM
 	help
 	  Note: This driver is deprecated and will be removed from the
 	  kernel in the near future!

 	  If you have a CDROM/DVD drive that supports packet writing, say
 	  Y to include support. It should work with any MMC/Mt Fuji
 	  compliant ATAPI or SCSI drive, which is just about any newer
 	  DVD/CD writer.

 	  Currently only writing to CD-RW, DVD-RW, DVD+RW and DVDRAM discs
 	  is possible.
 	  DVD-RW disks must be in restricted overwrite mode.

 	  See the file <file:Documentation/cdrom/packet-writing.rst>
 	  for further information on the use of this driver.

 	  To compile this driver as a module, choose M here: the
 	  module will be called pktcdvd.

 config CDROM_PKTCDVD_BUFFERS
 	int "Free buffers for data gathering"
 	depends on CDROM_PKTCDVD
 	default "8"
 	help
 	  This controls the maximum number of active concurrent packets. More
 	  concurrent packets can increase write performance, but also require
 	  more memory. Each concurrent packet will require approximately 64Kb
 	  of non-swappable kernel memory, memory which will be allocated when
 	  a disc is opened for writing.

 config CDROM_PKTCDVD_WCACHE
 	bool "Enable write caching"
 	depends on CDROM_PKTCDVD
 	help
 	  If enabled, write caching will be set for the CD-R/W device. For now
 	  this option is dangerous unless the CD-RW media is known good, as we
 	  don't do deferred write error handling yet.

 config ATA_OVER_ETH
 	tristate "ATA over Ethernet support"
 	depends on NET
 	help
 	This driver provides Support for ATA over Ethernet block
 	devices like the Coraid EtherDrive (R) Storage Blade.

 config SUNVDC
 	tristate "Sun Virtual Disk Client support"
 	depends on SUN_LDOMS
 	help
 	  Support for virtual disk devices as a client under Sun
 	  Logical Domains.

 source "drivers/s390/block/Kconfig"

 config XEN_BLKDEV_FRONTEND
 	tristate "Xen virtual block device support"
 	depends on XEN
 	default y
 	select XEN_XENBUS_FRONTEND
 	help
 	  This driver implements the front-end of the Xen virtual
 	  block device driver.  It communicates with a back-end driver
 	  in another domain which drives the actual block device.

 config XEN_BLKDEV_BACKEND
 	tristate "Xen block-device backend driver"
 	depends on XEN_BACKEND
 	help
 	  The block-device backend driver allows the kernel to export its
 	  block devices to other guests via a high-performance shared-memory
 	  interface.

 	  The corresponding Linux frontend driver is enabled by the
 	  CONFIG_XEN_BLKDEV_FRONTEND configuration option.

 	  The backend driver attaches itself to a any block device specified
 	  in the XenBus configuration. There are no limits to what the block
 	  device as long as it has a major and minor.

 	  If you are compiling a kernel to run in a Xen block backend driver
 	  domain (often this is domain 0) you should say Y here. To
 	  compile this driver as a module, chose M here: the module
 	  will be called xen-blkback.


 config VIRTIO_BLK
 	tristate "Virtio block driver"
 	depends on VIRTIO
 	select SG_POOL
 	help
 	  This is the virtual block driver for virtio.  It can be used with
           QEMU based VMMs (like KVM or Xen).  Say Y or M.

 config BLK_DEV_RBD
 	tristate "Rados block device (RBD)"
 	depends on INET && BLOCK
 	select CEPH_LIB
 	select LIBCRC32C
 	select CRYPTO_AES
 	select CRYPTO
 	help
 	  Say Y here if you want include the Rados block device, which stripes
 	  a block device over objects stored in the Ceph distributed object
 	  store.

 	  More information at http://ceph.newdream.net/.

 	  If unsure, say N.

 config BLK_DEV_UBLK
 	tristate "Userspace block driver (Experimental)"
 	select IO_URING
 	help
 	  io_uring based userspace block driver. Together with ublk server, ublk
 	  has been working well, but interface with userspace or command data
 	  definition isn't finalized yet, and might change according to future
 	  requirement, so mark is as experimental now.

 	  Say Y if you want to get better performance because task_work_add()
 	  can be used in IO path for replacing io_uring cmd, which will become
 	  shared between IO tasks and ubq daemon, meantime task_work_add() can
 	  can handle batch more effectively, but task_work_add() isn't exported
 	  for module, so ublk has to be built to kernel.

 config BLKDEV_UBLK_LEGACY_OPCODES
 	bool "Support legacy command opcode"
 	depends on BLK_DEV_UBLK
 	default y
 	help
 	  ublk driver started to take plain command encoding, which turns out
 	  one bad way. The traditional ioctl command opcode encodes more
 	  info and basically defines each code uniquely, so opcode conflict
 	  is avoided, and driver can handle wrong command easily, meantime it
 	  may help security subsystem to audit io_uring command.

 	  Say Y if your application still uses legacy command opcode.

 	  Say N if you don't want to support legacy command opcode. It is
 	  suggested to enable N if your application(ublk server) switches to
 	  ioctl command encoding.

 source "drivers/block/rnbd/Kconfig"

 endif # BLK_DEV
	# SPDX-License-Identifier: GPL-2.0
	#
	# Block device driver configuration
	#

	menuconfig BLK_DEV
	bool "Block devices"
	depends on BLOCK
	default y
	help
	Say Y here to get to see options for various different block device
	drivers. This option alone does not add any kernel code.

	If you say N, all options in this submenu will be skipped and disabled;
	only do this if you know what you are doing.

	if BLK_DEV

	source "drivers/block/null_blk/Kconfig"

	config BLK_DEV_FD
	tristate "Normal floppy disk support"
	depends on ARCH_MAY_HAVE_PC_FDC
	help
	If you want to use the floppy disk drive(s) of your PC under Linux,
	say Y. Information about this driver, especially important for IBM
	Thinkpad users, is contained in
	<file:Documentation/admin-guide/blockdev/floppy.rst>.
	That file also contains the location of the Floppy driver FAQ as
	well as location of the fdutils package used to configure additional
	parameters of the driver at run time.

	To compile this driver as a module, choose M here: the
	module will be called floppy.

	config BLK_DEV_FD_RAWCMD
	bool "Support for raw floppy disk commands (DEPRECATED)"
	depends on BLK_DEV_FD
	help
	If you want to use actual physical floppies and expect to do
	special low-level hardware accesses to them (access and use
	non-standard formats, for example), then enable this.

	Note that the code enabled by this option is rarely used and
	might be unstable or insecure, and distros should not enable it.

	Note: FDRAWCMD is deprecated and will be removed from the kernel
	in the near future.

	If unsure, say N.

	config AMIGA_FLOPPY
	tristate "Amiga floppy support"
	depends on AMIGA

	config ATARI_FLOPPY
	tristate "Atari floppy support"
	depends on ATARI

	config MAC_FLOPPY
	tristate "Support for PowerMac floppy"
	depends on PPC_PMAC && !PPC_PMAC64
	help
	If you have a SWIM-3 (Super Woz Integrated Machine 3; from Apple)
	floppy controller, say Y here. Most commonly found in PowerMacs.

	config BLK_DEV_SWIM
	tristate "Support for SWIM Macintosh floppy"
	depends on M68K && MAC && !HIGHMEM
	help
	You should select this option if you want floppy support
	and you don't have a II, IIfx, Q900, Q950 or AV series.

	config AMIGA_Z2RAM
	tristate "Amiga Zorro II ramdisk support"
	depends on ZORRO
	help
	This enables support for using Chip RAM and Zorro II RAM as a
	ramdisk or as a swap partition. Say Y if you want to include this
	driver in the kernel.

	To compile this driver as a module, choose M here: the
	module will be called z2ram.

	config N64CART
	bool "N64 cart support"
	depends on MACH_NINTENDO64
	help
	Support for the N64 cart.

	config CDROM
	tristate

	config GDROM
	tristate "SEGA Dreamcast GD-ROM drive"
	depends on SH_DREAMCAST
	select CDROM
	help
	A standard SEGA Dreamcast comes with a modified CD ROM drive called a
	"GD-ROM" by SEGA to signify it is capable of reading special disks
	with up to 1 GB of data. This drive will also read standard CD ROM
	disks. Select this option to access any disks in your GD ROM drive.
	Most users will want to say "Y" here.
	You can also build this as a module which will be called gdrom.

	source "drivers/block/mtip32xx/Kconfig"

	source "drivers/block/zram/Kconfig"

	config BLK_DEV_UBD
	bool "Virtual block device"
	depends on UML
	help
	The User-Mode Linux port includes a driver called UBD which will let
	you access arbitrary files on the host computer as block devices.
	Unless you know that you do not need such virtual block devices say
	Y here.

	config BLK_DEV_UBD_SYNC
	bool "Always do synchronous disk IO for UBD"
	depends on BLK_DEV_UBD
	help
	Writes to the virtual block device are not immediately written to the
	host's disk; this may cause problems if, for example, the User-Mode
	Linux 'Virtual Machine' uses a journalling filesystem and the host
	computer crashes.

	Synchronous operation (i.e. always writing data to the host's disk
	immediately) is configurable on a per-UBD basis by using a special
	kernel command line option. Alternatively, you can say Y here to
	turn on synchronous operation by default for all block devices.

	If you're running a journalling file system (like reiserfs, for
	example) in your virtual machine, you will want to say Y here. If
	you care for the safety of the data in your virtual machine, Y is a
	wise choice too. In all other cases (for example, if you're just
	playing around with User-Mode Linux) you can choose N.

	config BLK_DEV_COW_COMMON
	bool
	default BLK_DEV_UBD

	config BLK_DEV_LOOP
	tristate "Loopback device support"
	help
	Saying Y here will allow you to use a regular file as a block
	device; you can then create a file system on that block device and
	mount it just as you would mount other block devices such as hard
	drive partitions, CD-ROM drives or floppy drives. The loop devices
	are block special device files with major number 7 and typically
	called /dev/loop0, /dev/loop1 etc.

	This is useful if you want to check an ISO 9660 file system before
	burning the CD, or if you want to use floppy images without first
	writing them to floppy. Furthermore, some Linux distributions avoid
	the need for a dedicated Linux partition by keeping their complete
	root file system inside a DOS FAT file using this loop device
	driver.

	To use the loop device, you need the losetup utility, found in the
	util-linux package, see
	<https://www.kernel.org/pub/linux/utils/util-linux/>.

	The loop device driver can also be used to "hide" a file system in
	a disk partition, floppy, or regular file, either using encryption
	(scrambling the data) or steganography (hiding the data in the low
	bits of, say, a sound file). This is also safe if the file resides
	on a remote file server.

	Note that this loop device has nothing to do with the loopback
	device used for network connections from the machine to itself.

	To compile this driver as a module, choose M here: the
	module will be called loop.

	Most users will answer N here.

	config BLK_DEV_LOOP_MIN_COUNT
	int "Number of loop devices to pre-create at init time"
	depends on BLK_DEV_LOOP
	default 8
	help
	Static number of loop devices to be unconditionally pre-created
	at init time.

	This default value can be overwritten on the kernel command
	line or with module-parameter loop.max_loop.

	The historic default is 8. If a late 2011 version of losetup(8)
	is used, it can be set to 0, since needed loop devices can be
	dynamically allocated with the /dev/loop-control interface.

	source "drivers/block/drbd/Kconfig"

	config BLK_DEV_NBD
	tristate "Network block device support"
	depends on NET
	help
	Saying Y here will allow your computer to be a client for network
	block devices, i.e. it will be able to use block devices exported by
	servers (mount file systems on them etc.). Communication between
	client and server works over TCP/IP networking, but to the client
	program this is hidden: it looks like a regular local file access to
	a block device special file such as /dev/nd0.

	Network block devices also allows you to run a block-device in
	userland (making server and client physically the same computer,
	communicating using the loopback network device).

	Read <file:Documentation/admin-guide/blockdev/nbd.rst> for more information,
	especially about where to find the server code, which runs in user
	space and does not need special kernel support.

	Note that this has nothing to do with the network file systems NFS
	or Coda; you can say N here even if you intend to use NFS or Coda.

	To compile this driver as a module, choose M here: the
	module will be called nbd.

	If unsure, say N.

	config BLK_DEV_RAM
	tristate "RAM block device support"
	help
	Saying Y here will allow you to use a portion of your RAM memory as
	a block device, so that you can make file systems on it, read and
	write to it and do all the other things that you can do with normal
	block devices (such as hard drives). It is usually used to load and
	store a copy of a minimal root file system off of a floppy into RAM
	during the initial install of Linux.

	Note that the kernel command line option "ramdisk=XX" is now obsolete.
	For details, read <file:Documentation/admin-guide/blockdev/ramdisk.rst>.

	To compile this driver as a module, choose M here: the
	module will be called brd. An alias "rd" has been defined
	for historical reasons.

	Most normal users won't need the RAM disk functionality, and can
	thus say N here.

	config BLK_DEV_RAM_COUNT
	int "Default number of RAM disks"
	default "16"
	depends on BLK_DEV_RAM
	help
	The default value is 16 RAM disks. Change this if you know what you
	are doing. If you boot from a filesystem that needs to be extracted
	in memory, you will need at least one RAM disk (e.g. root on cramfs).

	config BLK_DEV_RAM_SIZE
	int "Default RAM disk size (kbytes)"
	depends on BLK_DEV_RAM
	default "4096"
	help
	The default value is 4096 kilobytes. Only change this if you know
	what you are doing.

	config CDROM_PKTCDVD
	tristate "Packet writing on CD/DVD media (DEPRECATED)"
	depends on !UML
	depends on SCSI
	select CDROM
	help
	Note: This driver is deprecated and will be removed from the
	kernel in the near future!

	If you have a CDROM/DVD drive that supports packet writing, say
	Y to include support. It should work with any MMC/Mt Fuji
	compliant ATAPI or SCSI drive, which is just about any newer
	DVD/CD writer.

	Currently only writing to CD-RW, DVD-RW, DVD+RW and DVDRAM discs
	is possible.
	DVD-RW disks must be in restricted overwrite mode.

	See the file <file:Documentation/cdrom/packet-writing.rst>
	for further information on the use of this driver.

	To compile this driver as a module, choose M here: the
	module will be called pktcdvd.

	config CDROM_PKTCDVD_BUFFERS
	int "Free buffers for data gathering"
	depends on CDROM_PKTCDVD
	default "8"
	help
	This controls the maximum number of active concurrent packets. More
	concurrent packets can increase write performance, but also require
	more memory. Each concurrent packet will require approximately 64Kb
	of non-swappable kernel memory, memory which will be allocated when
	a disc is opened for writing.

	config CDROM_PKTCDVD_WCACHE
	bool "Enable write caching"
	depends on CDROM_PKTCDVD
	help
	If enabled, write caching will be set for the CD-R/W device. For now
	this option is dangerous unless the CD-RW media is known good, as we
	don't do deferred write error handling yet.

	config ATA_OVER_ETH
	tristate "ATA over Ethernet support"
	depends on NET
	help
	This driver provides Support for ATA over Ethernet block
	devices like the Coraid EtherDrive (R) Storage Blade.

	config SUNVDC
	tristate "Sun Virtual Disk Client support"
	depends on SUN_LDOMS
	help
	Support for virtual disk devices as a client under Sun
	Logical Domains.

	source "drivers/s390/block/Kconfig"

	config XEN_BLKDEV_FRONTEND
	tristate "Xen virtual block device support"
	depends on XEN
	default y
	select XEN_XENBUS_FRONTEND
	help
	This driver implements the front-end of the Xen virtual
	block device driver. It communicates with a back-end driver
	in another domain which drives the actual block device.

	config XEN_BLKDEV_BACKEND
	tristate "Xen block-device backend driver"
	depends on XEN_BACKEND
	help
	The block-device backend driver allows the kernel to export its
	block devices to other guests via a high-performance shared-memory
	interface.

	The corresponding Linux frontend driver is enabled by the
	CONFIG_XEN_BLKDEV_FRONTEND configuration option.

	The backend driver attaches itself to a any block device specified
	in the XenBus configuration. There are no limits to what the block
	device as long as it has a major and minor.

	If you are compiling a kernel to run in a Xen block backend driver
	domain (often this is domain 0) you should say Y here. To
	compile this driver as a module, chose M here: the module
	will be called xen-blkback.


	config VIRTIO_BLK
	tristate "Virtio block driver"
	depends on VIRTIO
	select SG_POOL
	help
	This is the virtual block driver for virtio. It can be used with
	QEMU based VMMs (like KVM or Xen). Say Y or M.

	config BLK_DEV_RBD
	tristate "Rados block device (RBD)"
	depends on INET && BLOCK
	select CEPH_LIB
	select LIBCRC32C
	select CRYPTO_AES
	select CRYPTO
	help
	Say Y here if you want include the Rados block device, which stripes
	a block device over objects stored in the Ceph distributed object
	store.

	More information at http://ceph.newdream.net/.

	If unsure, say N.

	config BLK_DEV_UBLK
	tristate "Userspace block driver (Experimental)"
	select IO_URING
	help
	io_uring based userspace block driver. Together with ublk server, ublk
	has been working well, but interface with userspace or command data
	definition isn't finalized yet, and might change according to future
	requirement, so mark is as experimental now.

	Say Y if you want to get better performance because task_work_add()
	can be used in IO path for replacing io_uring cmd, which will become
	shared between IO tasks and ubq daemon, meantime task_work_add() can
	can handle batch more effectively, but task_work_add() isn't exported
	for module, so ublk has to be built to kernel.

	config BLKDEV_UBLK_LEGACY_OPCODES
	bool "Support legacy command opcode"
	depends on BLK_DEV_UBLK
	default y
	help
	ublk driver started to take plain command encoding, which turns out
	one bad way. The traditional ioctl command opcode encodes more
	info and basically defines each code uniquely, so opcode conflict
	is avoided, and driver can handle wrong command easily, meantime it
	may help security subsystem to audit io_uring command.

	Say Y if your application still uses legacy command opcode.

	Say N if you don't want to support legacy command opcode. It is
	suggested to enable N if your application(ublk server) switches to
	ioctl command encoding.

	source "drivers/block/rnbd/Kconfig"

	endif # BLK_DEV