| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * adv7511_cec.c - Analog Devices ADV7511/33 cec driver |
| * |
| * Copyright 2017 Cisco Systems, Inc. and/or its affiliates. All rights reserved. |
| */ |
| |
| #include <linux/device.h> |
| #include <linux/module.h> |
| #include <linux/slab.h> |
| #include <linux/clk.h> |
| |
| #include <media/cec.h> |
| |
| #include "adv7511.h" |
| |
| static const u8 ADV7511_REG_CEC_RX_FRAME_HDR[] = { |
| ADV7511_REG_CEC_RX1_FRAME_HDR, |
| ADV7511_REG_CEC_RX2_FRAME_HDR, |
| ADV7511_REG_CEC_RX3_FRAME_HDR, |
| }; |
| |
| static const u8 ADV7511_REG_CEC_RX_FRAME_LEN[] = { |
| ADV7511_REG_CEC_RX1_FRAME_LEN, |
| ADV7511_REG_CEC_RX2_FRAME_LEN, |
| ADV7511_REG_CEC_RX3_FRAME_LEN, |
| }; |
| |
| #define ADV7511_INT1_CEC_MASK \ |
| (ADV7511_INT1_CEC_TX_READY | ADV7511_INT1_CEC_TX_ARBIT_LOST | \ |
| ADV7511_INT1_CEC_TX_RETRY_TIMEOUT | ADV7511_INT1_CEC_RX_READY1 | \ |
| ADV7511_INT1_CEC_RX_READY2 | ADV7511_INT1_CEC_RX_READY3) |
| |
| static void adv_cec_tx_raw_status(struct adv7511 *adv7511, u8 tx_raw_status) |
| { |
| unsigned int offset = adv7511->info->reg_cec_offset; |
| unsigned int val; |
| |
| if (regmap_read(adv7511->regmap_cec, |
| ADV7511_REG_CEC_TX_ENABLE + offset, &val)) |
| return; |
| |
| if ((val & 0x01) == 0) |
| return; |
| |
| if (tx_raw_status & ADV7511_INT1_CEC_TX_ARBIT_LOST) { |
| cec_transmit_attempt_done(adv7511->cec_adap, |
| CEC_TX_STATUS_ARB_LOST); |
| return; |
| } |
| if (tx_raw_status & ADV7511_INT1_CEC_TX_RETRY_TIMEOUT) { |
| u8 status; |
| u8 err_cnt = 0; |
| u8 nack_cnt = 0; |
| u8 low_drive_cnt = 0; |
| unsigned int cnt; |
| |
| /* |
| * We set this status bit since this hardware performs |
| * retransmissions. |
| */ |
| status = CEC_TX_STATUS_MAX_RETRIES; |
| if (regmap_read(adv7511->regmap_cec, |
| ADV7511_REG_CEC_TX_LOW_DRV_CNT + offset, &cnt)) { |
| err_cnt = 1; |
| status |= CEC_TX_STATUS_ERROR; |
| } else { |
| nack_cnt = cnt & 0xf; |
| if (nack_cnt) |
| status |= CEC_TX_STATUS_NACK; |
| low_drive_cnt = cnt >> 4; |
| if (low_drive_cnt) |
| status |= CEC_TX_STATUS_LOW_DRIVE; |
| } |
| cec_transmit_done(adv7511->cec_adap, status, |
| 0, nack_cnt, low_drive_cnt, err_cnt); |
| return; |
| } |
| if (tx_raw_status & ADV7511_INT1_CEC_TX_READY) { |
| cec_transmit_attempt_done(adv7511->cec_adap, CEC_TX_STATUS_OK); |
| return; |
| } |
| } |
| |
| static void adv7511_cec_rx(struct adv7511 *adv7511, int rx_buf) |
| { |
| unsigned int offset = adv7511->info->reg_cec_offset; |
| struct cec_msg msg = {}; |
| unsigned int len; |
| unsigned int val; |
| u8 i; |
| |
| if (regmap_read(adv7511->regmap_cec, |
| ADV7511_REG_CEC_RX_FRAME_LEN[rx_buf] + offset, &len)) |
| return; |
| |
| msg.len = len & 0x1f; |
| |
| if (msg.len > 16) |
| msg.len = 16; |
| |
| if (!msg.len) |
| return; |
| |
| for (i = 0; i < msg.len; i++) { |
| regmap_read(adv7511->regmap_cec, |
| i + ADV7511_REG_CEC_RX_FRAME_HDR[rx_buf] + offset, |
| &val); |
| msg.msg[i] = val; |
| } |
| |
| /* Toggle RX Ready Clear bit to re-enable this RX buffer */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_RX_BUFFERS + offset, BIT(rx_buf), |
| BIT(rx_buf)); |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_RX_BUFFERS + offset, BIT(rx_buf), 0); |
| |
| cec_received_msg(adv7511->cec_adap, &msg); |
| } |
| |
| void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1) |
| { |
| unsigned int offset = adv7511->info->reg_cec_offset; |
| const u32 irq_tx_mask = ADV7511_INT1_CEC_TX_READY | |
| ADV7511_INT1_CEC_TX_ARBIT_LOST | |
| ADV7511_INT1_CEC_TX_RETRY_TIMEOUT; |
| const u32 irq_rx_mask = ADV7511_INT1_CEC_RX_READY1 | |
| ADV7511_INT1_CEC_RX_READY2 | |
| ADV7511_INT1_CEC_RX_READY3; |
| unsigned int rx_status; |
| int rx_order[3] = { -1, -1, -1 }; |
| int i; |
| |
| if (irq1 & irq_tx_mask) |
| adv_cec_tx_raw_status(adv7511, irq1); |
| |
| if (!(irq1 & irq_rx_mask)) |
| return; |
| |
| if (regmap_read(adv7511->regmap_cec, |
| ADV7511_REG_CEC_RX_STATUS + offset, &rx_status)) |
| return; |
| |
| /* |
| * ADV7511_REG_CEC_RX_STATUS[5:0] contains the reception order of RX |
| * buffers 0, 1, and 2 in bits [1:0], [3:2], and [5:4] respectively. |
| * The values are to be interpreted as follows: |
| * |
| * 0 = buffer unused |
| * 1 = buffer contains oldest received frame (if applicable) |
| * 2 = buffer contains second oldest received frame (if applicable) |
| * 3 = buffer contains third oldest received frame (if applicable) |
| * |
| * Fill rx_order with the sequence of RX buffer indices to |
| * read from in order, where -1 indicates that there are no |
| * more buffers to process. |
| */ |
| for (i = 0; i < 3; i++) { |
| unsigned int timestamp = (rx_status >> (2 * i)) & 0x3; |
| |
| if (timestamp) |
| rx_order[timestamp - 1] = i; |
| } |
| |
| /* Read CEC RX buffers in the appropriate order as prescribed above */ |
| for (i = 0; i < 3; i++) { |
| int rx_buf = rx_order[i]; |
| |
| if (rx_buf < 0) |
| break; |
| |
| adv7511_cec_rx(adv7511, rx_buf); |
| } |
| } |
| |
| static int adv7511_cec_adap_enable(struct cec_adapter *adap, bool enable) |
| { |
| struct adv7511 *adv7511 = cec_get_drvdata(adap); |
| unsigned int offset = adv7511->info->reg_cec_offset; |
| |
| if (adv7511->i2c_cec == NULL) |
| return -EIO; |
| |
| if (!adv7511->cec_enabled_adap && enable) { |
| /* power up cec section */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_CLK_DIV + offset, |
| 0x03, 0x01); |
| /* non-legacy mode and clear all rx buffers */ |
| regmap_write(adv7511->regmap_cec, |
| ADV7511_REG_CEC_RX_BUFFERS + offset, 0x0f); |
| regmap_write(adv7511->regmap_cec, |
| ADV7511_REG_CEC_RX_BUFFERS + offset, 0x08); |
| /* initially disable tx */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_TX_ENABLE + offset, 1, 0); |
| /* enabled irqs: */ |
| /* tx: ready */ |
| /* tx: arbitration lost */ |
| /* tx: retry timeout */ |
| /* rx: ready 1-3 */ |
| regmap_update_bits(adv7511->regmap, |
| ADV7511_REG_INT_ENABLE(1), 0x3f, |
| ADV7511_INT1_CEC_MASK); |
| } else if (adv7511->cec_enabled_adap && !enable) { |
| regmap_update_bits(adv7511->regmap, |
| ADV7511_REG_INT_ENABLE(1), 0x3f, 0); |
| /* disable address mask 1-3 */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_LOG_ADDR_MASK + offset, |
| 0x70, 0x00); |
| /* power down cec section */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_CLK_DIV + offset, |
| 0x03, 0x00); |
| adv7511->cec_valid_addrs = 0; |
| } |
| adv7511->cec_enabled_adap = enable; |
| return 0; |
| } |
| |
| static int adv7511_cec_adap_log_addr(struct cec_adapter *adap, u8 addr) |
| { |
| struct adv7511 *adv7511 = cec_get_drvdata(adap); |
| unsigned int offset = adv7511->info->reg_cec_offset; |
| unsigned int i, free_idx = ADV7511_MAX_ADDRS; |
| |
| if (!adv7511->cec_enabled_adap) |
| return addr == CEC_LOG_ADDR_INVALID ? 0 : -EIO; |
| |
| if (addr == CEC_LOG_ADDR_INVALID) { |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_LOG_ADDR_MASK + offset, |
| 0x70, 0); |
| adv7511->cec_valid_addrs = 0; |
| return 0; |
| } |
| |
| for (i = 0; i < ADV7511_MAX_ADDRS; i++) { |
| bool is_valid = adv7511->cec_valid_addrs & (1 << i); |
| |
| if (free_idx == ADV7511_MAX_ADDRS && !is_valid) |
| free_idx = i; |
| if (is_valid && adv7511->cec_addr[i] == addr) |
| return 0; |
| } |
| if (i == ADV7511_MAX_ADDRS) { |
| i = free_idx; |
| if (i == ADV7511_MAX_ADDRS) |
| return -ENXIO; |
| } |
| adv7511->cec_addr[i] = addr; |
| adv7511->cec_valid_addrs |= 1 << i; |
| |
| switch (i) { |
| case 0: |
| /* enable address mask 0 */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_LOG_ADDR_MASK + offset, |
| 0x10, 0x10); |
| /* set address for mask 0 */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_LOG_ADDR_0_1 + offset, |
| 0x0f, addr); |
| break; |
| case 1: |
| /* enable address mask 1 */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_LOG_ADDR_MASK + offset, |
| 0x20, 0x20); |
| /* set address for mask 1 */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_LOG_ADDR_0_1 + offset, |
| 0xf0, addr << 4); |
| break; |
| case 2: |
| /* enable address mask 2 */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_LOG_ADDR_MASK + offset, |
| 0x40, 0x40); |
| /* set address for mask 1 */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_LOG_ADDR_2 + offset, |
| 0x0f, addr); |
| break; |
| } |
| return 0; |
| } |
| |
| static int adv7511_cec_adap_transmit(struct cec_adapter *adap, u8 attempts, |
| u32 signal_free_time, struct cec_msg *msg) |
| { |
| struct adv7511 *adv7511 = cec_get_drvdata(adap); |
| unsigned int offset = adv7511->info->reg_cec_offset; |
| u8 len = msg->len; |
| unsigned int i; |
| |
| /* |
| * The number of retries is the number of attempts - 1, but retry |
| * at least once. It's not clear if a value of 0 is allowed, so |
| * let's do at least one retry. |
| */ |
| regmap_update_bits(adv7511->regmap_cec, |
| ADV7511_REG_CEC_TX_RETRY + offset, |
| 0x70, max(1, attempts - 1) << 4); |
| |
| /* blocking, clear cec tx irq status */ |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_INT(1), 0x38, 0x38); |
| |
| /* write data */ |
| for (i = 0; i < len; i++) |
| regmap_write(adv7511->regmap_cec, |
| i + ADV7511_REG_CEC_TX_FRAME_HDR + offset, |
| msg->msg[i]); |
| |
| /* set length (data + header) */ |
| regmap_write(adv7511->regmap_cec, |
| ADV7511_REG_CEC_TX_FRAME_LEN + offset, len); |
| /* start transmit, enable tx */ |
| regmap_write(adv7511->regmap_cec, |
| ADV7511_REG_CEC_TX_ENABLE + offset, 0x01); |
| return 0; |
| } |
| |
| static const struct cec_adap_ops adv7511_cec_adap_ops = { |
| .adap_enable = adv7511_cec_adap_enable, |
| .adap_log_addr = adv7511_cec_adap_log_addr, |
| .adap_transmit = adv7511_cec_adap_transmit, |
| }; |
| |
| static int adv7511_cec_parse_dt(struct device *dev, struct adv7511 *adv7511) |
| { |
| adv7511->cec_clk = devm_clk_get(dev, "cec"); |
| if (IS_ERR(adv7511->cec_clk)) { |
| int ret = PTR_ERR(adv7511->cec_clk); |
| |
| adv7511->cec_clk = NULL; |
| return ret; |
| } |
| clk_prepare_enable(adv7511->cec_clk); |
| adv7511->cec_clk_freq = clk_get_rate(adv7511->cec_clk); |
| return 0; |
| } |
| |
| int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511) |
| { |
| unsigned int offset = adv7511->info->reg_cec_offset; |
| int ret = adv7511_cec_parse_dt(dev, adv7511); |
| |
| if (ret) |
| goto err_cec_parse_dt; |
| |
| adv7511->cec_adap = cec_allocate_adapter(&adv7511_cec_adap_ops, |
| adv7511, dev_name(dev), CEC_CAP_DEFAULTS, ADV7511_MAX_ADDRS); |
| if (IS_ERR(adv7511->cec_adap)) { |
| ret = PTR_ERR(adv7511->cec_adap); |
| goto err_cec_alloc; |
| } |
| |
| regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL, 0); |
| /* cec soft reset */ |
| regmap_write(adv7511->regmap_cec, |
| ADV7511_REG_CEC_SOFT_RESET + offset, 0x01); |
| regmap_write(adv7511->regmap_cec, |
| ADV7511_REG_CEC_SOFT_RESET + offset, 0x00); |
| |
| /* non-legacy mode - use all three RX buffers */ |
| regmap_write(adv7511->regmap_cec, |
| ADV7511_REG_CEC_RX_BUFFERS + offset, 0x08); |
| |
| regmap_write(adv7511->regmap_cec, |
| ADV7511_REG_CEC_CLK_DIV + offset, |
| ((adv7511->cec_clk_freq / 750000) - 1) << 2); |
| |
| ret = cec_register_adapter(adv7511->cec_adap, dev); |
| if (ret) |
| goto err_cec_register; |
| return 0; |
| |
| err_cec_register: |
| cec_delete_adapter(adv7511->cec_adap); |
| adv7511->cec_adap = NULL; |
| err_cec_alloc: |
| dev_info(dev, "Initializing CEC failed with error %d, disabling CEC\n", |
| ret); |
| err_cec_parse_dt: |
| regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL, |
| ADV7511_CEC_CTRL_POWER_DOWN); |
| return ret == -EPROBE_DEFER ? ret : 0; |
| } |