| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (c) 2018, The Linux Foundation. All rights reserved. |
| * Copyright (c) 2019-2020. Linaro Limited. |
| */ |
| |
| #include <linux/firmware.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/i2c.h> |
| #include <linux/interrupt.h> |
| #include <linux/module.h> |
| #include <linux/mutex.h> |
| #include <linux/of_graph.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/wait.h> |
| #include <linux/workqueue.h> |
| |
| #include <sound/hdmi-codec.h> |
| |
| #include <drm/drm_atomic_helper.h> |
| #include <drm/drm_bridge.h> |
| #include <drm/drm_edid.h> |
| #include <drm/drm_mipi_dsi.h> |
| #include <drm/drm_print.h> |
| #include <drm/drm_probe_helper.h> |
| |
| #define EDID_BLOCK_SIZE 128 |
| #define EDID_NUM_BLOCKS 2 |
| |
| #define FW_FILE "lt9611uxc_fw.bin" |
| |
| struct lt9611uxc { |
| struct device *dev; |
| struct drm_bridge bridge; |
| struct drm_connector connector; |
| |
| struct regmap *regmap; |
| /* Protects all accesses to registers by stopping the on-chip MCU */ |
| struct mutex ocm_lock; |
| |
| struct wait_queue_head wq; |
| struct work_struct work; |
| |
| struct device_node *dsi0_node; |
| struct device_node *dsi1_node; |
| struct mipi_dsi_device *dsi0; |
| struct mipi_dsi_device *dsi1; |
| struct platform_device *audio_pdev; |
| |
| struct gpio_desc *reset_gpio; |
| struct gpio_desc *enable_gpio; |
| |
| struct regulator_bulk_data supplies[2]; |
| |
| struct i2c_client *client; |
| |
| bool hpd_supported; |
| bool edid_read; |
| /* can be accessed from different threads, so protect this with ocm_lock */ |
| bool hdmi_connected; |
| uint8_t fw_version; |
| }; |
| |
| #define LT9611_PAGE_CONTROL 0xff |
| |
| static const struct regmap_range_cfg lt9611uxc_ranges[] = { |
| { |
| .name = "register_range", |
| .range_min = 0, |
| .range_max = 0xd0ff, |
| .selector_reg = LT9611_PAGE_CONTROL, |
| .selector_mask = 0xff, |
| .selector_shift = 0, |
| .window_start = 0, |
| .window_len = 0x100, |
| }, |
| }; |
| |
| static const struct regmap_config lt9611uxc_regmap_config = { |
| .reg_bits = 8, |
| .val_bits = 8, |
| .max_register = 0xffff, |
| .ranges = lt9611uxc_ranges, |
| .num_ranges = ARRAY_SIZE(lt9611uxc_ranges), |
| }; |
| |
| struct lt9611uxc_mode { |
| u16 hdisplay; |
| u16 vdisplay; |
| u8 vrefresh; |
| }; |
| |
| /* |
| * This chip supports only a fixed set of modes. |
| * Enumerate them here to check whether the mode is supported. |
| */ |
| static struct lt9611uxc_mode lt9611uxc_modes[] = { |
| { 1920, 1080, 60 }, |
| { 1920, 1080, 30 }, |
| { 1920, 1080, 25 }, |
| { 1366, 768, 60 }, |
| { 1360, 768, 60 }, |
| { 1280, 1024, 60 }, |
| { 1280, 800, 60 }, |
| { 1280, 720, 60 }, |
| { 1280, 720, 50 }, |
| { 1280, 720, 30 }, |
| { 1152, 864, 60 }, |
| { 1024, 768, 60 }, |
| { 800, 600, 60 }, |
| { 720, 576, 50 }, |
| { 720, 480, 60 }, |
| { 640, 480, 60 }, |
| }; |
| |
| static struct lt9611uxc *bridge_to_lt9611uxc(struct drm_bridge *bridge) |
| { |
| return container_of(bridge, struct lt9611uxc, bridge); |
| } |
| |
| static struct lt9611uxc *connector_to_lt9611uxc(struct drm_connector *connector) |
| { |
| return container_of(connector, struct lt9611uxc, connector); |
| } |
| |
| static void lt9611uxc_lock(struct lt9611uxc *lt9611uxc) |
| { |
| mutex_lock(<9611uxc->ocm_lock); |
| regmap_write(lt9611uxc->regmap, 0x80ee, 0x01); |
| } |
| |
| static void lt9611uxc_unlock(struct lt9611uxc *lt9611uxc) |
| { |
| regmap_write(lt9611uxc->regmap, 0x80ee, 0x00); |
| msleep(50); |
| mutex_unlock(<9611uxc->ocm_lock); |
| } |
| |
| static irqreturn_t lt9611uxc_irq_thread_handler(int irq, void *dev_id) |
| { |
| struct lt9611uxc *lt9611uxc = dev_id; |
| unsigned int irq_status = 0; |
| unsigned int hpd_status = 0; |
| |
| lt9611uxc_lock(lt9611uxc); |
| |
| regmap_read(lt9611uxc->regmap, 0xb022, &irq_status); |
| regmap_read(lt9611uxc->regmap, 0xb023, &hpd_status); |
| if (irq_status) |
| regmap_write(lt9611uxc->regmap, 0xb022, 0); |
| |
| if (irq_status & BIT(0)) { |
| lt9611uxc->edid_read = !!(hpd_status & BIT(0)); |
| wake_up_all(<9611uxc->wq); |
| } |
| |
| if (irq_status & BIT(1)) { |
| lt9611uxc->hdmi_connected = hpd_status & BIT(1); |
| schedule_work(<9611uxc->work); |
| } |
| |
| lt9611uxc_unlock(lt9611uxc); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void lt9611uxc_hpd_work(struct work_struct *work) |
| { |
| struct lt9611uxc *lt9611uxc = container_of(work, struct lt9611uxc, work); |
| bool connected; |
| |
| if (lt9611uxc->connector.dev) { |
| if (lt9611uxc->connector.dev->mode_config.funcs) |
| drm_kms_helper_hotplug_event(lt9611uxc->connector.dev); |
| } else { |
| |
| mutex_lock(<9611uxc->ocm_lock); |
| connected = lt9611uxc->hdmi_connected; |
| mutex_unlock(<9611uxc->ocm_lock); |
| |
| drm_bridge_hpd_notify(<9611uxc->bridge, |
| connected ? |
| connector_status_connected : |
| connector_status_disconnected); |
| } |
| } |
| |
| static void lt9611uxc_reset(struct lt9611uxc *lt9611uxc) |
| { |
| gpiod_set_value_cansleep(lt9611uxc->reset_gpio, 1); |
| msleep(20); |
| |
| gpiod_set_value_cansleep(lt9611uxc->reset_gpio, 0); |
| msleep(20); |
| |
| gpiod_set_value_cansleep(lt9611uxc->reset_gpio, 1); |
| msleep(300); |
| } |
| |
| static void lt9611uxc_assert_5v(struct lt9611uxc *lt9611uxc) |
| { |
| if (!lt9611uxc->enable_gpio) |
| return; |
| |
| gpiod_set_value_cansleep(lt9611uxc->enable_gpio, 1); |
| msleep(20); |
| } |
| |
| static int lt9611uxc_regulator_init(struct lt9611uxc *lt9611uxc) |
| { |
| int ret; |
| |
| lt9611uxc->supplies[0].supply = "vdd"; |
| lt9611uxc->supplies[1].supply = "vcc"; |
| |
| ret = devm_regulator_bulk_get(lt9611uxc->dev, 2, lt9611uxc->supplies); |
| if (ret < 0) |
| return ret; |
| |
| return regulator_set_load(lt9611uxc->supplies[0].consumer, 200000); |
| } |
| |
| static int lt9611uxc_regulator_enable(struct lt9611uxc *lt9611uxc) |
| { |
| int ret; |
| |
| ret = regulator_enable(lt9611uxc->supplies[0].consumer); |
| if (ret < 0) |
| return ret; |
| |
| usleep_range(1000, 10000); /* 50000 according to dtsi */ |
| |
| ret = regulator_enable(lt9611uxc->supplies[1].consumer); |
| if (ret < 0) { |
| regulator_disable(lt9611uxc->supplies[0].consumer); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static struct lt9611uxc_mode *lt9611uxc_find_mode(const struct drm_display_mode *mode) |
| { |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(lt9611uxc_modes); i++) { |
| if (lt9611uxc_modes[i].hdisplay == mode->hdisplay && |
| lt9611uxc_modes[i].vdisplay == mode->vdisplay && |
| lt9611uxc_modes[i].vrefresh == drm_mode_vrefresh(mode)) { |
| return <9611uxc_modes[i]; |
| } |
| } |
| |
| return NULL; |
| } |
| |
| static struct mipi_dsi_device *lt9611uxc_attach_dsi(struct lt9611uxc *lt9611uxc, |
| struct device_node *dsi_node) |
| { |
| const struct mipi_dsi_device_info info = { "lt9611uxc", 0, NULL }; |
| struct mipi_dsi_device *dsi; |
| struct mipi_dsi_host *host; |
| struct device *dev = lt9611uxc->dev; |
| int ret; |
| |
| host = of_find_mipi_dsi_host_by_node(dsi_node); |
| if (!host) { |
| dev_err(dev, "failed to find dsi host\n"); |
| return ERR_PTR(-EPROBE_DEFER); |
| } |
| |
| dsi = devm_mipi_dsi_device_register_full(dev, host, &info); |
| if (IS_ERR(dsi)) { |
| dev_err(dev, "failed to create dsi device\n"); |
| return dsi; |
| } |
| |
| dsi->lanes = 4; |
| dsi->format = MIPI_DSI_FMT_RGB888; |
| dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE | |
| MIPI_DSI_MODE_VIDEO_HSE; |
| |
| ret = devm_mipi_dsi_attach(dev, dsi); |
| if (ret < 0) { |
| dev_err(dev, "failed to attach dsi to host\n"); |
| return ERR_PTR(ret); |
| } |
| |
| return dsi; |
| } |
| |
| static int lt9611uxc_connector_get_modes(struct drm_connector *connector) |
| { |
| struct lt9611uxc *lt9611uxc = connector_to_lt9611uxc(connector); |
| unsigned int count; |
| const struct drm_edid *drm_edid; |
| |
| drm_edid = drm_bridge_edid_read(<9611uxc->bridge, connector); |
| drm_edid_connector_update(connector, drm_edid); |
| count = drm_edid_connector_add_modes(connector); |
| drm_edid_free(drm_edid); |
| |
| return count; |
| } |
| |
| static enum drm_connector_status lt9611uxc_connector_detect(struct drm_connector *connector, |
| bool force) |
| { |
| struct lt9611uxc *lt9611uxc = connector_to_lt9611uxc(connector); |
| |
| return lt9611uxc->bridge.funcs->detect(<9611uxc->bridge); |
| } |
| |
| static enum drm_mode_status lt9611uxc_connector_mode_valid(struct drm_connector *connector, |
| struct drm_display_mode *mode) |
| { |
| struct lt9611uxc_mode *lt9611uxc_mode = lt9611uxc_find_mode(mode); |
| |
| return lt9611uxc_mode ? MODE_OK : MODE_BAD; |
| } |
| |
| static const struct drm_connector_helper_funcs lt9611uxc_bridge_connector_helper_funcs = { |
| .get_modes = lt9611uxc_connector_get_modes, |
| .mode_valid = lt9611uxc_connector_mode_valid, |
| }; |
| |
| static const struct drm_connector_funcs lt9611uxc_bridge_connector_funcs = { |
| .fill_modes = drm_helper_probe_single_connector_modes, |
| .detect = lt9611uxc_connector_detect, |
| .destroy = drm_connector_cleanup, |
| .reset = drm_atomic_helper_connector_reset, |
| .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, |
| .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, |
| }; |
| |
| static int lt9611uxc_connector_init(struct drm_bridge *bridge, struct lt9611uxc *lt9611uxc) |
| { |
| int ret; |
| |
| if (!bridge->encoder) { |
| DRM_ERROR("Parent encoder object not found"); |
| return -ENODEV; |
| } |
| |
| lt9611uxc->connector.polled = DRM_CONNECTOR_POLL_HPD; |
| |
| drm_connector_helper_add(<9611uxc->connector, |
| <9611uxc_bridge_connector_helper_funcs); |
| ret = drm_connector_init(bridge->dev, <9611uxc->connector, |
| <9611uxc_bridge_connector_funcs, |
| DRM_MODE_CONNECTOR_HDMIA); |
| if (ret) { |
| DRM_ERROR("Failed to initialize connector with drm\n"); |
| return ret; |
| } |
| |
| return drm_connector_attach_encoder(<9611uxc->connector, bridge->encoder); |
| } |
| |
| static int lt9611uxc_bridge_attach(struct drm_bridge *bridge, |
| enum drm_bridge_attach_flags flags) |
| { |
| struct lt9611uxc *lt9611uxc = bridge_to_lt9611uxc(bridge); |
| int ret; |
| |
| if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) { |
| ret = lt9611uxc_connector_init(bridge, lt9611uxc); |
| if (ret < 0) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static enum drm_mode_status |
| lt9611uxc_bridge_mode_valid(struct drm_bridge *bridge, |
| const struct drm_display_info *info, |
| const struct drm_display_mode *mode) |
| { |
| struct lt9611uxc_mode *lt9611uxc_mode; |
| |
| lt9611uxc_mode = lt9611uxc_find_mode(mode); |
| |
| return lt9611uxc_mode ? MODE_OK : MODE_BAD; |
| } |
| |
| static void lt9611uxc_video_setup(struct lt9611uxc *lt9611uxc, |
| const struct drm_display_mode *mode) |
| { |
| u32 h_total, hactive, hsync_len, hfront_porch; |
| u32 v_total, vactive, vsync_len, vfront_porch; |
| |
| h_total = mode->htotal; |
| v_total = mode->vtotal; |
| |
| hactive = mode->hdisplay; |
| hsync_len = mode->hsync_end - mode->hsync_start; |
| hfront_porch = mode->hsync_start - mode->hdisplay; |
| |
| vactive = mode->vdisplay; |
| vsync_len = mode->vsync_end - mode->vsync_start; |
| vfront_porch = mode->vsync_start - mode->vdisplay; |
| |
| regmap_write(lt9611uxc->regmap, 0xd00d, (u8)(v_total / 256)); |
| regmap_write(lt9611uxc->regmap, 0xd00e, (u8)(v_total % 256)); |
| |
| regmap_write(lt9611uxc->regmap, 0xd00f, (u8)(vactive / 256)); |
| regmap_write(lt9611uxc->regmap, 0xd010, (u8)(vactive % 256)); |
| |
| regmap_write(lt9611uxc->regmap, 0xd011, (u8)(h_total / 256)); |
| regmap_write(lt9611uxc->regmap, 0xd012, (u8)(h_total % 256)); |
| |
| regmap_write(lt9611uxc->regmap, 0xd013, (u8)(hactive / 256)); |
| regmap_write(lt9611uxc->regmap, 0xd014, (u8)(hactive % 256)); |
| |
| regmap_write(lt9611uxc->regmap, 0xd015, (u8)(vsync_len % 256)); |
| |
| regmap_update_bits(lt9611uxc->regmap, 0xd016, 0xf, (u8)(hsync_len / 256)); |
| regmap_write(lt9611uxc->regmap, 0xd017, (u8)(hsync_len % 256)); |
| |
| regmap_update_bits(lt9611uxc->regmap, 0xd018, 0xf, (u8)(vfront_porch / 256)); |
| regmap_write(lt9611uxc->regmap, 0xd019, (u8)(vfront_porch % 256)); |
| |
| regmap_update_bits(lt9611uxc->regmap, 0xd01a, 0xf, (u8)(hfront_porch / 256)); |
| regmap_write(lt9611uxc->regmap, 0xd01b, (u8)(hfront_porch % 256)); |
| } |
| |
| static void lt9611uxc_bridge_mode_set(struct drm_bridge *bridge, |
| const struct drm_display_mode *mode, |
| const struct drm_display_mode *adj_mode) |
| { |
| struct lt9611uxc *lt9611uxc = bridge_to_lt9611uxc(bridge); |
| |
| lt9611uxc_lock(lt9611uxc); |
| lt9611uxc_video_setup(lt9611uxc, mode); |
| lt9611uxc_unlock(lt9611uxc); |
| } |
| |
| static enum drm_connector_status lt9611uxc_bridge_detect(struct drm_bridge *bridge) |
| { |
| struct lt9611uxc *lt9611uxc = bridge_to_lt9611uxc(bridge); |
| unsigned int reg_val = 0; |
| int ret; |
| bool connected = true; |
| |
| lt9611uxc_lock(lt9611uxc); |
| |
| if (lt9611uxc->hpd_supported) { |
| ret = regmap_read(lt9611uxc->regmap, 0xb023, ®_val); |
| |
| if (ret) |
| dev_err(lt9611uxc->dev, "failed to read hpd status: %d\n", ret); |
| else |
| connected = reg_val & BIT(1); |
| } |
| lt9611uxc->hdmi_connected = connected; |
| |
| lt9611uxc_unlock(lt9611uxc); |
| |
| return connected ? connector_status_connected : |
| connector_status_disconnected; |
| } |
| |
| static int lt9611uxc_wait_for_edid(struct lt9611uxc *lt9611uxc) |
| { |
| return wait_event_interruptible_timeout(lt9611uxc->wq, lt9611uxc->edid_read, |
| msecs_to_jiffies(500)); |
| } |
| |
| static int lt9611uxc_get_edid_block(void *data, u8 *buf, unsigned int block, size_t len) |
| { |
| struct lt9611uxc *lt9611uxc = data; |
| int ret; |
| |
| if (len > EDID_BLOCK_SIZE) |
| return -EINVAL; |
| |
| if (block >= EDID_NUM_BLOCKS) |
| return -EINVAL; |
| |
| lt9611uxc_lock(lt9611uxc); |
| |
| regmap_write(lt9611uxc->regmap, 0xb00b, 0x10); |
| |
| regmap_write(lt9611uxc->regmap, 0xb00a, block * EDID_BLOCK_SIZE); |
| |
| ret = regmap_noinc_read(lt9611uxc->regmap, 0xb0b0, buf, len); |
| if (ret) |
| dev_err(lt9611uxc->dev, "edid read failed: %d\n", ret); |
| |
| lt9611uxc_unlock(lt9611uxc); |
| |
| return 0; |
| }; |
| |
| static const struct drm_edid *lt9611uxc_bridge_edid_read(struct drm_bridge *bridge, |
| struct drm_connector *connector) |
| { |
| struct lt9611uxc *lt9611uxc = bridge_to_lt9611uxc(bridge); |
| int ret; |
| |
| ret = lt9611uxc_wait_for_edid(lt9611uxc); |
| if (ret < 0) { |
| dev_err(lt9611uxc->dev, "wait for EDID failed: %d\n", ret); |
| return NULL; |
| } else if (ret == 0) { |
| dev_err(lt9611uxc->dev, "wait for EDID timeout\n"); |
| return NULL; |
| } |
| |
| return drm_edid_read_custom(connector, lt9611uxc_get_edid_block, lt9611uxc); |
| } |
| |
| static const struct drm_bridge_funcs lt9611uxc_bridge_funcs = { |
| .attach = lt9611uxc_bridge_attach, |
| .mode_valid = lt9611uxc_bridge_mode_valid, |
| .mode_set = lt9611uxc_bridge_mode_set, |
| .detect = lt9611uxc_bridge_detect, |
| .edid_read = lt9611uxc_bridge_edid_read, |
| }; |
| |
| static int lt9611uxc_parse_dt(struct device *dev, |
| struct lt9611uxc *lt9611uxc) |
| { |
| lt9611uxc->dsi0_node = of_graph_get_remote_node(dev->of_node, 0, -1); |
| if (!lt9611uxc->dsi0_node) { |
| dev_err(lt9611uxc->dev, "failed to get remote node for primary dsi\n"); |
| return -ENODEV; |
| } |
| |
| lt9611uxc->dsi1_node = of_graph_get_remote_node(dev->of_node, 1, -1); |
| |
| return 0; |
| } |
| |
| static int lt9611uxc_gpio_init(struct lt9611uxc *lt9611uxc) |
| { |
| struct device *dev = lt9611uxc->dev; |
| |
| lt9611uxc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); |
| if (IS_ERR(lt9611uxc->reset_gpio)) { |
| dev_err(dev, "failed to acquire reset gpio\n"); |
| return PTR_ERR(lt9611uxc->reset_gpio); |
| } |
| |
| lt9611uxc->enable_gpio = devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW); |
| if (IS_ERR(lt9611uxc->enable_gpio)) { |
| dev_err(dev, "failed to acquire enable gpio\n"); |
| return PTR_ERR(lt9611uxc->enable_gpio); |
| } |
| |
| return 0; |
| } |
| |
| static int lt9611uxc_read_device_rev(struct lt9611uxc *lt9611uxc) |
| { |
| unsigned int rev0, rev1, rev2; |
| int ret; |
| |
| lt9611uxc_lock(lt9611uxc); |
| |
| ret = regmap_read(lt9611uxc->regmap, 0x8100, &rev0); |
| ret |= regmap_read(lt9611uxc->regmap, 0x8101, &rev1); |
| ret |= regmap_read(lt9611uxc->regmap, 0x8102, &rev2); |
| if (ret) |
| dev_err(lt9611uxc->dev, "failed to read revision: %d\n", ret); |
| else |
| dev_info(lt9611uxc->dev, "LT9611 revision: 0x%02x.%02x.%02x\n", rev0, rev1, rev2); |
| |
| lt9611uxc_unlock(lt9611uxc); |
| |
| return ret; |
| } |
| |
| static int lt9611uxc_read_version(struct lt9611uxc *lt9611uxc) |
| { |
| unsigned int rev; |
| int ret; |
| |
| lt9611uxc_lock(lt9611uxc); |
| |
| ret = regmap_read(lt9611uxc->regmap, 0xb021, &rev); |
| if (ret) |
| dev_err(lt9611uxc->dev, "failed to read revision: %d\n", ret); |
| else |
| dev_info(lt9611uxc->dev, "LT9611 version: 0x%02x\n", rev); |
| |
| lt9611uxc_unlock(lt9611uxc); |
| |
| return ret < 0 ? ret : rev; |
| } |
| |
| static int lt9611uxc_hdmi_hw_params(struct device *dev, void *data, |
| struct hdmi_codec_daifmt *fmt, |
| struct hdmi_codec_params *hparms) |
| { |
| /* |
| * LT9611UXC will automatically detect rate and sample size, so no need |
| * to setup anything here. |
| */ |
| return 0; |
| } |
| |
| static void lt9611uxc_audio_shutdown(struct device *dev, void *data) |
| { |
| } |
| |
| static int lt9611uxc_hdmi_i2s_get_dai_id(struct snd_soc_component *component, |
| struct device_node *endpoint) |
| { |
| struct of_endpoint of_ep; |
| int ret; |
| |
| ret = of_graph_parse_endpoint(endpoint, &of_ep); |
| if (ret < 0) |
| return ret; |
| |
| /* |
| * HDMI sound should be located as reg = <2> |
| * Then, it is sound port 0 |
| */ |
| if (of_ep.port == 2) |
| return 0; |
| |
| return -EINVAL; |
| } |
| |
| static const struct hdmi_codec_ops lt9611uxc_codec_ops = { |
| .hw_params = lt9611uxc_hdmi_hw_params, |
| .audio_shutdown = lt9611uxc_audio_shutdown, |
| .get_dai_id = lt9611uxc_hdmi_i2s_get_dai_id, |
| }; |
| |
| static int lt9611uxc_audio_init(struct device *dev, struct lt9611uxc *lt9611uxc) |
| { |
| struct hdmi_codec_pdata codec_data = { |
| .ops = <9611uxc_codec_ops, |
| .max_i2s_channels = 2, |
| .i2s = 1, |
| .data = lt9611uxc, |
| }; |
| |
| lt9611uxc->audio_pdev = |
| platform_device_register_data(dev, HDMI_CODEC_DRV_NAME, |
| PLATFORM_DEVID_AUTO, |
| &codec_data, sizeof(codec_data)); |
| |
| return PTR_ERR_OR_ZERO(lt9611uxc->audio_pdev); |
| } |
| |
| static void lt9611uxc_audio_exit(struct lt9611uxc *lt9611uxc) |
| { |
| if (lt9611uxc->audio_pdev) { |
| platform_device_unregister(lt9611uxc->audio_pdev); |
| lt9611uxc->audio_pdev = NULL; |
| } |
| } |
| |
| #define LT9611UXC_FW_PAGE_SIZE 32 |
| static void lt9611uxc_firmware_write_page(struct lt9611uxc *lt9611uxc, u16 addr, const u8 *buf) |
| { |
| struct reg_sequence seq_write_prepare[] = { |
| REG_SEQ0(0x805a, 0x04), |
| REG_SEQ0(0x805a, 0x00), |
| |
| REG_SEQ0(0x805e, 0xdf), |
| REG_SEQ0(0x805a, 0x20), |
| REG_SEQ0(0x805a, 0x00), |
| REG_SEQ0(0x8058, 0x21), |
| }; |
| |
| struct reg_sequence seq_write_addr[] = { |
| REG_SEQ0(0x805b, (addr >> 16) & 0xff), |
| REG_SEQ0(0x805c, (addr >> 8) & 0xff), |
| REG_SEQ0(0x805d, addr & 0xff), |
| REG_SEQ0(0x805a, 0x10), |
| REG_SEQ0(0x805a, 0x00), |
| }; |
| |
| regmap_write(lt9611uxc->regmap, 0x8108, 0xbf); |
| msleep(20); |
| regmap_write(lt9611uxc->regmap, 0x8108, 0xff); |
| msleep(20); |
| regmap_multi_reg_write(lt9611uxc->regmap, seq_write_prepare, ARRAY_SIZE(seq_write_prepare)); |
| regmap_noinc_write(lt9611uxc->regmap, 0x8059, buf, LT9611UXC_FW_PAGE_SIZE); |
| regmap_multi_reg_write(lt9611uxc->regmap, seq_write_addr, ARRAY_SIZE(seq_write_addr)); |
| msleep(20); |
| } |
| |
| static void lt9611uxc_firmware_read_page(struct lt9611uxc *lt9611uxc, u16 addr, char *buf) |
| { |
| struct reg_sequence seq_read_page[] = { |
| REG_SEQ0(0x805a, 0xa0), |
| REG_SEQ0(0x805a, 0x80), |
| REG_SEQ0(0x805b, (addr >> 16) & 0xff), |
| REG_SEQ0(0x805c, (addr >> 8) & 0xff), |
| REG_SEQ0(0x805d, addr & 0xff), |
| REG_SEQ0(0x805a, 0x90), |
| REG_SEQ0(0x805a, 0x80), |
| REG_SEQ0(0x8058, 0x21), |
| }; |
| |
| regmap_multi_reg_write(lt9611uxc->regmap, seq_read_page, ARRAY_SIZE(seq_read_page)); |
| regmap_noinc_read(lt9611uxc->regmap, 0x805f, buf, LT9611UXC_FW_PAGE_SIZE); |
| } |
| |
| static char *lt9611uxc_firmware_read(struct lt9611uxc *lt9611uxc, size_t size) |
| { |
| struct reg_sequence seq_read_setup[] = { |
| REG_SEQ0(0x805a, 0x84), |
| REG_SEQ0(0x805a, 0x80), |
| }; |
| |
| char *readbuf; |
| u16 offset; |
| |
| readbuf = kzalloc(ALIGN(size, 32), GFP_KERNEL); |
| if (!readbuf) |
| return NULL; |
| |
| regmap_multi_reg_write(lt9611uxc->regmap, seq_read_setup, ARRAY_SIZE(seq_read_setup)); |
| |
| for (offset = 0; |
| offset < size; |
| offset += LT9611UXC_FW_PAGE_SIZE) |
| lt9611uxc_firmware_read_page(lt9611uxc, offset, &readbuf[offset]); |
| |
| return readbuf; |
| } |
| |
| static int lt9611uxc_firmware_update(struct lt9611uxc *lt9611uxc) |
| { |
| int ret; |
| u16 offset; |
| size_t remain; |
| char *readbuf; |
| const struct firmware *fw; |
| |
| struct reg_sequence seq_setup[] = { |
| REG_SEQ0(0x805e, 0xdf), |
| REG_SEQ0(0x8058, 0x00), |
| REG_SEQ0(0x8059, 0x50), |
| REG_SEQ0(0x805a, 0x10), |
| REG_SEQ0(0x805a, 0x00), |
| }; |
| |
| |
| struct reg_sequence seq_block_erase[] = { |
| REG_SEQ0(0x805a, 0x04), |
| REG_SEQ0(0x805a, 0x00), |
| REG_SEQ0(0x805b, 0x00), |
| REG_SEQ0(0x805c, 0x00), |
| REG_SEQ0(0x805d, 0x00), |
| REG_SEQ0(0x805a, 0x01), |
| REG_SEQ0(0x805a, 0x00), |
| }; |
| |
| ret = request_firmware(&fw, FW_FILE, lt9611uxc->dev); |
| if (ret < 0) |
| return ret; |
| |
| dev_info(lt9611uxc->dev, "Updating firmware\n"); |
| lt9611uxc_lock(lt9611uxc); |
| |
| regmap_multi_reg_write(lt9611uxc->regmap, seq_setup, ARRAY_SIZE(seq_setup)); |
| |
| /* |
| * Need erase block 2 timess here. Sometimes, block erase can fail. |
| * This is a workaroud. |
| */ |
| regmap_multi_reg_write(lt9611uxc->regmap, seq_block_erase, ARRAY_SIZE(seq_block_erase)); |
| msleep(3000); |
| regmap_multi_reg_write(lt9611uxc->regmap, seq_block_erase, ARRAY_SIZE(seq_block_erase)); |
| msleep(3000); |
| |
| for (offset = 0, remain = fw->size; |
| remain >= LT9611UXC_FW_PAGE_SIZE; |
| offset += LT9611UXC_FW_PAGE_SIZE, remain -= LT9611UXC_FW_PAGE_SIZE) |
| lt9611uxc_firmware_write_page(lt9611uxc, offset, fw->data + offset); |
| |
| if (remain > 0) { |
| char buf[LT9611UXC_FW_PAGE_SIZE]; |
| |
| memset(buf, 0xff, LT9611UXC_FW_PAGE_SIZE); |
| memcpy(buf, fw->data + offset, remain); |
| lt9611uxc_firmware_write_page(lt9611uxc, offset, buf); |
| } |
| msleep(20); |
| |
| readbuf = lt9611uxc_firmware_read(lt9611uxc, fw->size); |
| if (!readbuf) { |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| if (!memcmp(readbuf, fw->data, fw->size)) { |
| dev_err(lt9611uxc->dev, "Firmware update failed\n"); |
| print_hex_dump(KERN_ERR, "fw: ", DUMP_PREFIX_OFFSET, 16, 1, readbuf, fw->size, false); |
| ret = -EINVAL; |
| } else { |
| dev_info(lt9611uxc->dev, "Firmware updates successfully\n"); |
| ret = 0; |
| } |
| kfree(readbuf); |
| |
| out: |
| lt9611uxc_unlock(lt9611uxc); |
| lt9611uxc_reset(lt9611uxc); |
| release_firmware(fw); |
| |
| return ret; |
| } |
| |
| static ssize_t lt9611uxc_firmware_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t len) |
| { |
| struct lt9611uxc *lt9611uxc = dev_get_drvdata(dev); |
| int ret; |
| |
| ret = lt9611uxc_firmware_update(lt9611uxc); |
| if (ret < 0) |
| return ret; |
| return len; |
| } |
| |
| static ssize_t lt9611uxc_firmware_show(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct lt9611uxc *lt9611uxc = dev_get_drvdata(dev); |
| |
| return sysfs_emit(buf, "%02x\n", lt9611uxc->fw_version); |
| } |
| |
| static DEVICE_ATTR_RW(lt9611uxc_firmware); |
| |
| static struct attribute *lt9611uxc_attrs[] = { |
| &dev_attr_lt9611uxc_firmware.attr, |
| NULL, |
| }; |
| |
| static const struct attribute_group lt9611uxc_attr_group = { |
| .attrs = lt9611uxc_attrs, |
| }; |
| |
| static const struct attribute_group *lt9611uxc_attr_groups[] = { |
| <9611uxc_attr_group, |
| NULL, |
| }; |
| |
| static int lt9611uxc_probe(struct i2c_client *client) |
| { |
| struct lt9611uxc *lt9611uxc; |
| struct device *dev = &client->dev; |
| int ret; |
| bool fw_updated = false; |
| |
| if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { |
| dev_err(dev, "device doesn't support I2C\n"); |
| return -ENODEV; |
| } |
| |
| lt9611uxc = devm_kzalloc(dev, sizeof(*lt9611uxc), GFP_KERNEL); |
| if (!lt9611uxc) |
| return -ENOMEM; |
| |
| lt9611uxc->dev = dev; |
| lt9611uxc->client = client; |
| mutex_init(<9611uxc->ocm_lock); |
| |
| lt9611uxc->regmap = devm_regmap_init_i2c(client, <9611uxc_regmap_config); |
| if (IS_ERR(lt9611uxc->regmap)) { |
| dev_err(lt9611uxc->dev, "regmap i2c init failed\n"); |
| return PTR_ERR(lt9611uxc->regmap); |
| } |
| |
| ret = lt9611uxc_parse_dt(dev, lt9611uxc); |
| if (ret) { |
| dev_err(dev, "failed to parse device tree\n"); |
| return ret; |
| } |
| |
| ret = lt9611uxc_gpio_init(lt9611uxc); |
| if (ret < 0) |
| goto err_of_put; |
| |
| ret = lt9611uxc_regulator_init(lt9611uxc); |
| if (ret < 0) |
| goto err_of_put; |
| |
| lt9611uxc_assert_5v(lt9611uxc); |
| |
| ret = lt9611uxc_regulator_enable(lt9611uxc); |
| if (ret) |
| goto err_of_put; |
| |
| lt9611uxc_reset(lt9611uxc); |
| |
| ret = lt9611uxc_read_device_rev(lt9611uxc); |
| if (ret) { |
| dev_err(dev, "failed to read chip rev\n"); |
| goto err_disable_regulators; |
| } |
| |
| retry: |
| ret = lt9611uxc_read_version(lt9611uxc); |
| if (ret < 0) { |
| dev_err(dev, "failed to read FW version\n"); |
| goto err_disable_regulators; |
| } else if (ret == 0) { |
| if (!fw_updated) { |
| fw_updated = true; |
| dev_err(dev, "FW version 0, enforcing firmware update\n"); |
| ret = lt9611uxc_firmware_update(lt9611uxc); |
| if (ret < 0) |
| goto err_disable_regulators; |
| else |
| goto retry; |
| } else { |
| dev_err(dev, "FW version 0, update failed\n"); |
| ret = -EOPNOTSUPP; |
| goto err_disable_regulators; |
| } |
| } else if (ret < 0x40) { |
| dev_info(dev, "FW version 0x%x, HPD not supported\n", ret); |
| } else { |
| lt9611uxc->hpd_supported = true; |
| } |
| lt9611uxc->fw_version = ret; |
| |
| init_waitqueue_head(<9611uxc->wq); |
| INIT_WORK(<9611uxc->work, lt9611uxc_hpd_work); |
| |
| ret = request_threaded_irq(client->irq, NULL, |
| lt9611uxc_irq_thread_handler, |
| IRQF_ONESHOT, "lt9611uxc", lt9611uxc); |
| if (ret) { |
| dev_err(dev, "failed to request irq\n"); |
| goto err_disable_regulators; |
| } |
| |
| i2c_set_clientdata(client, lt9611uxc); |
| |
| lt9611uxc->bridge.funcs = <9611uxc_bridge_funcs; |
| lt9611uxc->bridge.of_node = client->dev.of_node; |
| lt9611uxc->bridge.ops = DRM_BRIDGE_OP_DETECT | DRM_BRIDGE_OP_EDID; |
| if (lt9611uxc->hpd_supported) |
| lt9611uxc->bridge.ops |= DRM_BRIDGE_OP_HPD; |
| lt9611uxc->bridge.type = DRM_MODE_CONNECTOR_HDMIA; |
| |
| drm_bridge_add(<9611uxc->bridge); |
| |
| /* Attach primary DSI */ |
| lt9611uxc->dsi0 = lt9611uxc_attach_dsi(lt9611uxc, lt9611uxc->dsi0_node); |
| if (IS_ERR(lt9611uxc->dsi0)) { |
| ret = PTR_ERR(lt9611uxc->dsi0); |
| goto err_remove_bridge; |
| } |
| |
| /* Attach secondary DSI, if specified */ |
| if (lt9611uxc->dsi1_node) { |
| lt9611uxc->dsi1 = lt9611uxc_attach_dsi(lt9611uxc, lt9611uxc->dsi1_node); |
| if (IS_ERR(lt9611uxc->dsi1)) { |
| ret = PTR_ERR(lt9611uxc->dsi1); |
| goto err_remove_bridge; |
| } |
| } |
| |
| return lt9611uxc_audio_init(dev, lt9611uxc); |
| |
| err_remove_bridge: |
| free_irq(client->irq, lt9611uxc); |
| cancel_work_sync(<9611uxc->work); |
| drm_bridge_remove(<9611uxc->bridge); |
| |
| err_disable_regulators: |
| regulator_bulk_disable(ARRAY_SIZE(lt9611uxc->supplies), lt9611uxc->supplies); |
| |
| err_of_put: |
| of_node_put(lt9611uxc->dsi1_node); |
| of_node_put(lt9611uxc->dsi0_node); |
| |
| return ret; |
| } |
| |
| static void lt9611uxc_remove(struct i2c_client *client) |
| { |
| struct lt9611uxc *lt9611uxc = i2c_get_clientdata(client); |
| |
| free_irq(client->irq, lt9611uxc); |
| cancel_work_sync(<9611uxc->work); |
| lt9611uxc_audio_exit(lt9611uxc); |
| drm_bridge_remove(<9611uxc->bridge); |
| |
| mutex_destroy(<9611uxc->ocm_lock); |
| |
| regulator_bulk_disable(ARRAY_SIZE(lt9611uxc->supplies), lt9611uxc->supplies); |
| |
| of_node_put(lt9611uxc->dsi1_node); |
| of_node_put(lt9611uxc->dsi0_node); |
| } |
| |
| static struct i2c_device_id lt9611uxc_id[] = { |
| { "lontium,lt9611uxc", 0 }, |
| { /* sentinel */ } |
| }; |
| |
| static const struct of_device_id lt9611uxc_match_table[] = { |
| { .compatible = "lontium,lt9611uxc" }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, lt9611uxc_match_table); |
| |
| static struct i2c_driver lt9611uxc_driver = { |
| .driver = { |
| .name = "lt9611uxc", |
| .of_match_table = lt9611uxc_match_table, |
| .dev_groups = lt9611uxc_attr_groups, |
| }, |
| .probe = lt9611uxc_probe, |
| .remove = lt9611uxc_remove, |
| .id_table = lt9611uxc_id, |
| }; |
| module_i2c_driver(lt9611uxc_driver); |
| |
| MODULE_AUTHOR("Dmitry Baryshkov <dmitry.baryshkov@linaro.org>"); |
| MODULE_LICENSE("GPL v2"); |
| |
| MODULE_FIRMWARE(FW_FILE); |