| // SPDX-License-Identifier: GPL-2.0-only |
| /************************************************************************** |
| * Copyright (c) 2011, Intel Corporation. |
| * All Rights Reserved. |
| * |
| **************************************************************************/ |
| |
| #include <linux/delay.h> |
| |
| #include <drm/drm.h> |
| #include <drm/drm_crtc_helper.h> |
| |
| #include "cdv_device.h" |
| #include "gma_device.h" |
| #include "intel_bios.h" |
| #include "psb_drv.h" |
| #include "psb_intel_reg.h" |
| #include "psb_reg.h" |
| |
| #define VGA_SR_INDEX 0x3c4 |
| #define VGA_SR_DATA 0x3c5 |
| |
| static void cdv_disable_vga(struct drm_device *dev) |
| { |
| u8 sr1; |
| u32 vga_reg; |
| |
| vga_reg = VGACNTRL; |
| |
| outb(1, VGA_SR_INDEX); |
| sr1 = inb(VGA_SR_DATA); |
| outb(sr1 | 1<<5, VGA_SR_DATA); |
| udelay(300); |
| |
| REG_WRITE(vga_reg, VGA_DISP_DISABLE); |
| REG_READ(vga_reg); |
| } |
| |
| static int cdv_output_init(struct drm_device *dev) |
| { |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| |
| drm_mode_create_scaling_mode_property(dev); |
| |
| cdv_disable_vga(dev); |
| |
| cdv_intel_crt_init(dev, &dev_priv->mode_dev); |
| cdv_intel_lvds_init(dev, &dev_priv->mode_dev); |
| |
| /* These bits indicate HDMI not SDVO on CDV */ |
| if (REG_READ(SDVOB) & SDVO_DETECTED) { |
| cdv_hdmi_init(dev, &dev_priv->mode_dev, SDVOB); |
| if (REG_READ(DP_B) & DP_DETECTED) |
| cdv_intel_dp_init(dev, &dev_priv->mode_dev, DP_B); |
| } |
| |
| if (REG_READ(SDVOC) & SDVO_DETECTED) { |
| cdv_hdmi_init(dev, &dev_priv->mode_dev, SDVOC); |
| if (REG_READ(DP_C) & DP_DETECTED) |
| cdv_intel_dp_init(dev, &dev_priv->mode_dev, DP_C); |
| } |
| return 0; |
| } |
| |
| /* |
| * Cedartrail Backlght Interfaces |
| */ |
| |
| static int cdv_backlight_combination_mode(struct drm_device *dev) |
| { |
| return REG_READ(BLC_PWM_CTL2) & PWM_LEGACY_MODE; |
| } |
| |
| static u32 cdv_get_max_backlight(struct drm_device *dev) |
| { |
| u32 max = REG_READ(BLC_PWM_CTL); |
| |
| if (max == 0) { |
| DRM_DEBUG_KMS("LVDS Panel PWM value is 0!\n"); |
| /* i915 does this, I believe which means that we should not |
| * smash PWM control as firmware will take control of it. */ |
| return 1; |
| } |
| |
| max >>= 16; |
| if (cdv_backlight_combination_mode(dev)) |
| max *= 0xff; |
| return max; |
| } |
| |
| static int cdv_get_brightness(struct drm_device *dev) |
| { |
| struct pci_dev *pdev = to_pci_dev(dev->dev); |
| u32 val = REG_READ(BLC_PWM_CTL) & BACKLIGHT_DUTY_CYCLE_MASK; |
| |
| if (cdv_backlight_combination_mode(dev)) { |
| u8 lbpc; |
| |
| val &= ~1; |
| pci_read_config_byte(pdev, 0xF4, &lbpc); |
| val *= lbpc; |
| } |
| return (val * 100)/cdv_get_max_backlight(dev); |
| } |
| |
| static void cdv_set_brightness(struct drm_device *dev, int level) |
| { |
| struct pci_dev *pdev = to_pci_dev(dev->dev); |
| u32 blc_pwm_ctl; |
| |
| level *= cdv_get_max_backlight(dev); |
| level /= 100; |
| |
| if (cdv_backlight_combination_mode(dev)) { |
| u32 max = cdv_get_max_backlight(dev); |
| u8 lbpc; |
| |
| lbpc = level * 0xfe / max + 1; |
| level /= lbpc; |
| |
| pci_write_config_byte(pdev, 0xF4, lbpc); |
| } |
| |
| blc_pwm_ctl = REG_READ(BLC_PWM_CTL) & ~BACKLIGHT_DUTY_CYCLE_MASK; |
| REG_WRITE(BLC_PWM_CTL, (blc_pwm_ctl | |
| (level << BACKLIGHT_DUTY_CYCLE_SHIFT))); |
| } |
| |
| static int cdv_backlight_init(struct drm_device *dev) |
| { |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| |
| dev_priv->backlight_level = cdv_get_brightness(dev); |
| cdv_set_brightness(dev, dev_priv->backlight_level); |
| |
| return 0; |
| } |
| |
| /* |
| * Provide the Cedarview specific chip logic and low level methods |
| * for power management |
| * |
| * FIXME: we need to implement the apm/ospm base management bits |
| * for this and the MID devices. |
| */ |
| |
| static inline u32 CDV_MSG_READ32(int domain, uint port, uint offset) |
| { |
| int mcr = (0x10<<24) | (port << 16) | (offset << 8); |
| uint32_t ret_val = 0; |
| struct pci_dev *pci_root = pci_get_domain_bus_and_slot(domain, 0, 0); |
| pci_write_config_dword(pci_root, 0xD0, mcr); |
| pci_read_config_dword(pci_root, 0xD4, &ret_val); |
| pci_dev_put(pci_root); |
| return ret_val; |
| } |
| |
| static inline void CDV_MSG_WRITE32(int domain, uint port, uint offset, |
| u32 value) |
| { |
| int mcr = (0x11<<24) | (port << 16) | (offset << 8) | 0xF0; |
| struct pci_dev *pci_root = pci_get_domain_bus_and_slot(domain, 0, 0); |
| pci_write_config_dword(pci_root, 0xD4, value); |
| pci_write_config_dword(pci_root, 0xD0, mcr); |
| pci_dev_put(pci_root); |
| } |
| |
| #define PSB_PM_SSC 0x20 |
| #define PSB_PM_SSS 0x30 |
| #define PSB_PWRGT_GFX_ON 0x02 |
| #define PSB_PWRGT_GFX_OFF 0x01 |
| #define PSB_PWRGT_GFX_D0 0x00 |
| #define PSB_PWRGT_GFX_D3 0x03 |
| |
| static void cdv_init_pm(struct drm_device *dev) |
| { |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| struct pci_dev *pdev = to_pci_dev(dev->dev); |
| u32 pwr_cnt; |
| int domain = pci_domain_nr(pdev->bus); |
| int i; |
| |
| dev_priv->apm_base = CDV_MSG_READ32(domain, PSB_PUNIT_PORT, |
| PSB_APMBA) & 0xFFFF; |
| dev_priv->ospm_base = CDV_MSG_READ32(domain, PSB_PUNIT_PORT, |
| PSB_OSPMBA) & 0xFFFF; |
| |
| /* Power status */ |
| pwr_cnt = inl(dev_priv->apm_base + PSB_APM_CMD); |
| |
| /* Enable the GPU */ |
| pwr_cnt &= ~PSB_PWRGT_GFX_MASK; |
| pwr_cnt |= PSB_PWRGT_GFX_ON; |
| outl(pwr_cnt, dev_priv->apm_base + PSB_APM_CMD); |
| |
| /* Wait for the GPU power */ |
| for (i = 0; i < 5; i++) { |
| u32 pwr_sts = inl(dev_priv->apm_base + PSB_APM_STS); |
| if ((pwr_sts & PSB_PWRGT_GFX_MASK) == 0) |
| return; |
| udelay(10); |
| } |
| dev_err(dev->dev, "GPU: power management timed out.\n"); |
| } |
| |
| static void cdv_errata(struct drm_device *dev) |
| { |
| struct pci_dev *pdev = to_pci_dev(dev->dev); |
| |
| /* Disable bonus launch. |
| * CPU and GPU competes for memory and display misses updates and |
| * flickers. Worst with dual core, dual displays. |
| * |
| * Fixes were done to Win 7 gfx driver to disable a feature called |
| * Bonus Launch to work around the issue, by degrading |
| * performance. |
| */ |
| CDV_MSG_WRITE32(pci_domain_nr(pdev->bus), 3, 0x30, 0x08027108); |
| } |
| |
| /** |
| * cdv_save_display_registers - save registers lost on suspend |
| * @dev: our DRM device |
| * |
| * Save the state we need in order to be able to restore the interface |
| * upon resume from suspend |
| */ |
| static int cdv_save_display_registers(struct drm_device *dev) |
| { |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| struct pci_dev *pdev = to_pci_dev(dev->dev); |
| struct psb_save_area *regs = &dev_priv->regs; |
| struct drm_connector_list_iter conn_iter; |
| struct drm_connector *connector; |
| |
| dev_dbg(dev->dev, "Saving GPU registers.\n"); |
| |
| pci_read_config_byte(pdev, 0xF4, ®s->cdv.saveLBB); |
| |
| regs->cdv.saveDSPCLK_GATE_D = REG_READ(DSPCLK_GATE_D); |
| regs->cdv.saveRAMCLK_GATE_D = REG_READ(RAMCLK_GATE_D); |
| |
| regs->cdv.saveDSPARB = REG_READ(DSPARB); |
| regs->cdv.saveDSPFW[0] = REG_READ(DSPFW1); |
| regs->cdv.saveDSPFW[1] = REG_READ(DSPFW2); |
| regs->cdv.saveDSPFW[2] = REG_READ(DSPFW3); |
| regs->cdv.saveDSPFW[3] = REG_READ(DSPFW4); |
| regs->cdv.saveDSPFW[4] = REG_READ(DSPFW5); |
| regs->cdv.saveDSPFW[5] = REG_READ(DSPFW6); |
| |
| regs->cdv.saveADPA = REG_READ(ADPA); |
| |
| regs->cdv.savePP_CONTROL = REG_READ(PP_CONTROL); |
| regs->cdv.savePFIT_PGM_RATIOS = REG_READ(PFIT_PGM_RATIOS); |
| regs->saveBLC_PWM_CTL = REG_READ(BLC_PWM_CTL); |
| regs->saveBLC_PWM_CTL2 = REG_READ(BLC_PWM_CTL2); |
| regs->cdv.saveLVDS = REG_READ(LVDS); |
| |
| regs->cdv.savePFIT_CONTROL = REG_READ(PFIT_CONTROL); |
| |
| regs->cdv.savePP_ON_DELAYS = REG_READ(PP_ON_DELAYS); |
| regs->cdv.savePP_OFF_DELAYS = REG_READ(PP_OFF_DELAYS); |
| regs->cdv.savePP_CYCLE = REG_READ(PP_CYCLE); |
| |
| regs->cdv.saveVGACNTRL = REG_READ(VGACNTRL); |
| |
| regs->cdv.saveIER = REG_READ(PSB_INT_ENABLE_R); |
| regs->cdv.saveIMR = REG_READ(PSB_INT_MASK_R); |
| |
| drm_connector_list_iter_begin(dev, &conn_iter); |
| drm_for_each_connector_iter(connector, &conn_iter) |
| connector->funcs->dpms(connector, DRM_MODE_DPMS_OFF); |
| drm_connector_list_iter_end(&conn_iter); |
| |
| return 0; |
| } |
| |
| /** |
| * cdv_restore_display_registers - restore lost register state |
| * @dev: our DRM device |
| * |
| * Restore register state that was lost during suspend and resume. |
| * |
| * FIXME: review |
| */ |
| static int cdv_restore_display_registers(struct drm_device *dev) |
| { |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| struct pci_dev *pdev = to_pci_dev(dev->dev); |
| struct psb_save_area *regs = &dev_priv->regs; |
| struct drm_connector_list_iter conn_iter; |
| struct drm_connector *connector; |
| u32 temp; |
| |
| pci_write_config_byte(pdev, 0xF4, regs->cdv.saveLBB); |
| |
| REG_WRITE(DSPCLK_GATE_D, regs->cdv.saveDSPCLK_GATE_D); |
| REG_WRITE(RAMCLK_GATE_D, regs->cdv.saveRAMCLK_GATE_D); |
| |
| /* BIOS does below anyway */ |
| REG_WRITE(DPIO_CFG, 0); |
| REG_WRITE(DPIO_CFG, DPIO_MODE_SELECT_0 | DPIO_CMN_RESET_N); |
| |
| temp = REG_READ(DPLL_A); |
| if ((temp & DPLL_SYNCLOCK_ENABLE) == 0) { |
| REG_WRITE(DPLL_A, temp | DPLL_SYNCLOCK_ENABLE); |
| REG_READ(DPLL_A); |
| } |
| |
| temp = REG_READ(DPLL_B); |
| if ((temp & DPLL_SYNCLOCK_ENABLE) == 0) { |
| REG_WRITE(DPLL_B, temp | DPLL_SYNCLOCK_ENABLE); |
| REG_READ(DPLL_B); |
| } |
| |
| udelay(500); |
| |
| REG_WRITE(DSPFW1, regs->cdv.saveDSPFW[0]); |
| REG_WRITE(DSPFW2, regs->cdv.saveDSPFW[1]); |
| REG_WRITE(DSPFW3, regs->cdv.saveDSPFW[2]); |
| REG_WRITE(DSPFW4, regs->cdv.saveDSPFW[3]); |
| REG_WRITE(DSPFW5, regs->cdv.saveDSPFW[4]); |
| REG_WRITE(DSPFW6, regs->cdv.saveDSPFW[5]); |
| |
| REG_WRITE(DSPARB, regs->cdv.saveDSPARB); |
| REG_WRITE(ADPA, regs->cdv.saveADPA); |
| |
| REG_WRITE(BLC_PWM_CTL2, regs->saveBLC_PWM_CTL2); |
| REG_WRITE(LVDS, regs->cdv.saveLVDS); |
| REG_WRITE(PFIT_CONTROL, regs->cdv.savePFIT_CONTROL); |
| REG_WRITE(PFIT_PGM_RATIOS, regs->cdv.savePFIT_PGM_RATIOS); |
| REG_WRITE(BLC_PWM_CTL, regs->saveBLC_PWM_CTL); |
| REG_WRITE(PP_ON_DELAYS, regs->cdv.savePP_ON_DELAYS); |
| REG_WRITE(PP_OFF_DELAYS, regs->cdv.savePP_OFF_DELAYS); |
| REG_WRITE(PP_CYCLE, regs->cdv.savePP_CYCLE); |
| REG_WRITE(PP_CONTROL, regs->cdv.savePP_CONTROL); |
| |
| REG_WRITE(VGACNTRL, regs->cdv.saveVGACNTRL); |
| |
| REG_WRITE(PSB_INT_ENABLE_R, regs->cdv.saveIER); |
| REG_WRITE(PSB_INT_MASK_R, regs->cdv.saveIMR); |
| |
| /* Fix arbitration bug */ |
| cdv_errata(dev); |
| |
| drm_mode_config_reset(dev); |
| |
| drm_connector_list_iter_begin(dev, &conn_iter); |
| drm_for_each_connector_iter(connector, &conn_iter) |
| connector->funcs->dpms(connector, DRM_MODE_DPMS_ON); |
| drm_connector_list_iter_end(&conn_iter); |
| |
| /* Resume the modeset for every activated CRTC */ |
| drm_helper_resume_force_mode(dev); |
| return 0; |
| } |
| |
| static int cdv_power_down(struct drm_device *dev) |
| { |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| u32 pwr_cnt, pwr_mask, pwr_sts; |
| int tries = 5; |
| |
| pwr_cnt = inl(dev_priv->apm_base + PSB_APM_CMD); |
| pwr_cnt &= ~PSB_PWRGT_GFX_MASK; |
| pwr_cnt |= PSB_PWRGT_GFX_OFF; |
| pwr_mask = PSB_PWRGT_GFX_MASK; |
| |
| outl(pwr_cnt, dev_priv->apm_base + PSB_APM_CMD); |
| |
| while (tries--) { |
| pwr_sts = inl(dev_priv->apm_base + PSB_APM_STS); |
| if ((pwr_sts & pwr_mask) == PSB_PWRGT_GFX_D3) |
| return 0; |
| udelay(10); |
| } |
| return 0; |
| } |
| |
| static int cdv_power_up(struct drm_device *dev) |
| { |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| u32 pwr_cnt, pwr_mask, pwr_sts; |
| int tries = 5; |
| |
| pwr_cnt = inl(dev_priv->apm_base + PSB_APM_CMD); |
| pwr_cnt &= ~PSB_PWRGT_GFX_MASK; |
| pwr_cnt |= PSB_PWRGT_GFX_ON; |
| pwr_mask = PSB_PWRGT_GFX_MASK; |
| |
| outl(pwr_cnt, dev_priv->apm_base + PSB_APM_CMD); |
| |
| while (tries--) { |
| pwr_sts = inl(dev_priv->apm_base + PSB_APM_STS); |
| if ((pwr_sts & pwr_mask) == PSB_PWRGT_GFX_D0) |
| return 0; |
| udelay(10); |
| } |
| return 0; |
| } |
| |
| static void cdv_hotplug_work_func(struct work_struct *work) |
| { |
| struct drm_psb_private *dev_priv = container_of(work, struct drm_psb_private, |
| hotplug_work); |
| struct drm_device *dev = &dev_priv->dev; |
| |
| /* Just fire off a uevent and let userspace tell us what to do */ |
| drm_helper_hpd_irq_event(dev); |
| } |
| |
| /* The core driver has received a hotplug IRQ. We are in IRQ context |
| so extract the needed information and kick off queued processing */ |
| |
| static int cdv_hotplug_event(struct drm_device *dev) |
| { |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| schedule_work(&dev_priv->hotplug_work); |
| REG_WRITE(PORT_HOTPLUG_STAT, REG_READ(PORT_HOTPLUG_STAT)); |
| return 1; |
| } |
| |
| static void cdv_hotplug_enable(struct drm_device *dev, bool on) |
| { |
| if (on) { |
| u32 hotplug = REG_READ(PORT_HOTPLUG_EN); |
| hotplug |= HDMIB_HOTPLUG_INT_EN | HDMIC_HOTPLUG_INT_EN | |
| HDMID_HOTPLUG_INT_EN | CRT_HOTPLUG_INT_EN; |
| REG_WRITE(PORT_HOTPLUG_EN, hotplug); |
| } else { |
| REG_WRITE(PORT_HOTPLUG_EN, 0); |
| REG_WRITE(PORT_HOTPLUG_STAT, REG_READ(PORT_HOTPLUG_STAT)); |
| } |
| } |
| |
| static const char *force_audio_names[] = { |
| "off", |
| "auto", |
| "on", |
| }; |
| |
| void cdv_intel_attach_force_audio_property(struct drm_connector *connector) |
| { |
| struct drm_device *dev = connector->dev; |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| struct drm_property *prop; |
| int i; |
| |
| prop = dev_priv->force_audio_property; |
| if (prop == NULL) { |
| prop = drm_property_create(dev, DRM_MODE_PROP_ENUM, |
| "audio", |
| ARRAY_SIZE(force_audio_names)); |
| if (prop == NULL) |
| return; |
| |
| for (i = 0; i < ARRAY_SIZE(force_audio_names); i++) |
| drm_property_add_enum(prop, i-1, force_audio_names[i]); |
| |
| dev_priv->force_audio_property = prop; |
| } |
| drm_object_attach_property(&connector->base, prop, 0); |
| } |
| |
| |
| static const char *broadcast_rgb_names[] = { |
| "Full", |
| "Limited 16:235", |
| }; |
| |
| void cdv_intel_attach_broadcast_rgb_property(struct drm_connector *connector) |
| { |
| struct drm_device *dev = connector->dev; |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| struct drm_property *prop; |
| int i; |
| |
| prop = dev_priv->broadcast_rgb_property; |
| if (prop == NULL) { |
| prop = drm_property_create(dev, DRM_MODE_PROP_ENUM, |
| "Broadcast RGB", |
| ARRAY_SIZE(broadcast_rgb_names)); |
| if (prop == NULL) |
| return; |
| |
| for (i = 0; i < ARRAY_SIZE(broadcast_rgb_names); i++) |
| drm_property_add_enum(prop, i, broadcast_rgb_names[i]); |
| |
| dev_priv->broadcast_rgb_property = prop; |
| } |
| |
| drm_object_attach_property(&connector->base, prop, 0); |
| } |
| |
| /* Cedarview */ |
| static const struct psb_offset cdv_regmap[2] = { |
| { |
| .fp0 = FPA0, |
| .fp1 = FPA1, |
| .cntr = DSPACNTR, |
| .conf = PIPEACONF, |
| .src = PIPEASRC, |
| .dpll = DPLL_A, |
| .dpll_md = DPLL_A_MD, |
| .htotal = HTOTAL_A, |
| .hblank = HBLANK_A, |
| .hsync = HSYNC_A, |
| .vtotal = VTOTAL_A, |
| .vblank = VBLANK_A, |
| .vsync = VSYNC_A, |
| .stride = DSPASTRIDE, |
| .size = DSPASIZE, |
| .pos = DSPAPOS, |
| .base = DSPABASE, |
| .surf = DSPASURF, |
| .addr = DSPABASE, |
| .status = PIPEASTAT, |
| .linoff = DSPALINOFF, |
| .tileoff = DSPATILEOFF, |
| .palette = PALETTE_A, |
| }, |
| { |
| .fp0 = FPB0, |
| .fp1 = FPB1, |
| .cntr = DSPBCNTR, |
| .conf = PIPEBCONF, |
| .src = PIPEBSRC, |
| .dpll = DPLL_B, |
| .dpll_md = DPLL_B_MD, |
| .htotal = HTOTAL_B, |
| .hblank = HBLANK_B, |
| .hsync = HSYNC_B, |
| .vtotal = VTOTAL_B, |
| .vblank = VBLANK_B, |
| .vsync = VSYNC_B, |
| .stride = DSPBSTRIDE, |
| .size = DSPBSIZE, |
| .pos = DSPBPOS, |
| .base = DSPBBASE, |
| .surf = DSPBSURF, |
| .addr = DSPBBASE, |
| .status = PIPEBSTAT, |
| .linoff = DSPBLINOFF, |
| .tileoff = DSPBTILEOFF, |
| .palette = PALETTE_B, |
| } |
| }; |
| |
| static int cdv_chip_setup(struct drm_device *dev) |
| { |
| struct drm_psb_private *dev_priv = to_drm_psb_private(dev); |
| INIT_WORK(&dev_priv->hotplug_work, cdv_hotplug_work_func); |
| |
| dev_priv->use_msi = true; |
| dev_priv->regmap = cdv_regmap; |
| gma_get_core_freq(dev); |
| psb_intel_opregion_init(dev); |
| psb_intel_init_bios(dev); |
| cdv_hotplug_enable(dev, false); |
| return 0; |
| } |
| |
| /* CDV is much like Poulsbo but has MID like SGX offsets and PM */ |
| |
| const struct psb_ops cdv_chip_ops = { |
| .name = "GMA3600/3650", |
| .pipes = 2, |
| .crtcs = 2, |
| .hdmi_mask = (1 << 0) | (1 << 1), |
| .lvds_mask = (1 << 1), |
| .sdvo_mask = (1 << 0), |
| .cursor_needs_phys = 0, |
| .sgx_offset = MRST_SGX_OFFSET, |
| .chip_setup = cdv_chip_setup, |
| .errata = cdv_errata, |
| |
| .crtc_helper = &cdv_intel_helper_funcs, |
| .clock_funcs = &cdv_clock_funcs, |
| |
| .output_init = cdv_output_init, |
| .hotplug = cdv_hotplug_event, |
| .hotplug_enable = cdv_hotplug_enable, |
| |
| .backlight_init = cdv_backlight_init, |
| .backlight_get = cdv_get_brightness, |
| .backlight_set = cdv_set_brightness, |
| .backlight_name = "psb-bl", |
| |
| .init_pm = cdv_init_pm, |
| .save_regs = cdv_save_display_registers, |
| .restore_regs = cdv_restore_display_registers, |
| .save_crtc = gma_crtc_save, |
| .restore_crtc = gma_crtc_restore, |
| .power_down = cdv_power_down, |
| .power_up = cdv_power_up, |
| .update_wm = cdv_update_wm, |
| .disable_sr = cdv_disable_sr, |
| }; |