blob: 5bbe81862c8f981891155574b3b5705b15861e87 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/display/bridge/adi,adv7511.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Analog Devices ADV7511/11W/13 HDMI Encoders
maintainers:
- Laurent Pinchart <laurent.pinchart@ideasonboard.com>
description: |
The ADV7511, ADV7511W and ADV7513 are HDMI audio and video
transmitters compatible with HDMI 1.4 and DVI 1.0. They support color
space conversion, S/PDIF, CEC and HDCP. The transmitter input is
parallel RGB or YUV data.
properties:
compatible:
enum:
- adi,adv7511
- adi,adv7511w
- adi,adv7513
reg:
description: |
I2C slave addresses.
The ADV7511/11W/13 internal registers are split into four pages
exposed through different I2C addresses, creating four register
maps. Each map has it own I2C address and acts as a standard slave
device on the I2C bus. The main address is mandatory, others are
optional and revert to defaults if not specified.
minItems: 1
maxItems: 4
reg-names:
description:
Names of maps with programmable addresses. It can contain any map
needing a non-default address.
minItems: 1
items:
- const: main
- const: edid
- const: cec
- const: packet
clocks:
description: Reference to the CEC clock.
maxItems: 1
clock-names:
const: cec
interrupts:
maxItems: 1
pd-gpios:
description: GPIO connected to the power down signal.
maxItems: 1
avdd-supply:
description: A 1.8V supply that powers up the AVDD pin.
dvdd-supply:
description: A 1.8V supply that powers up the DVDD pin.
pvdd-supply:
description: A 1.8V supply that powers up the PVDD pin.
dvdd-3v-supply:
description: A 3.3V supply that powers up the DVDD_3V pin.
bgvdd-supply:
description: A 1.8V supply that powers up the BGVDD pin.
adi,input-depth:
description: Number of bits per color component at the input.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [ 8, 10, 12 ]
adi,input-colorspace:
description: Input color space.
enum: [ rgb, yuv422, yuv444 ]
adi,input-clock:
description: |
Input clock type.
"1x": one clock cycle per pixel
"2x": two clock cycles per pixel
"dd": one clock cycle per pixel, data driven on both edges
enum: [ 1x, 2x, dd ]
adi,clock-delay:
description:
Video data clock delay relative to the pixel clock, in ps
(-1200ps .. 1600 ps).
$ref: /schemas/types.yaml#/definitions/uint32
default: 0
adi,embedded-sync:
description:
If defined, the input uses synchronization signals embedded in the
data stream (similar to BT.656).
type: boolean
adi,input-style:
description:
Input components arrangement variant as listed in the input
format tables in the datasheet.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [ 1, 2, 3 ]
adi,input-justification:
description: Input bit justification.
enum: [ left, evenly, right ]
ports:
description:
The ADV7511(W)/13 has two video ports and one audio port.
$ref: /schemas/graph.yaml#/properties/ports
properties:
port@0:
description: Video port for the RGB or YUV input.
$ref: /schemas/graph.yaml#/properties/port
port@1:
description: Video port for the HDMI output.
$ref: /schemas/graph.yaml#/properties/port
port@2:
description: Audio port for the HDMI output.
$ref: /schemas/graph.yaml#/properties/port
# adi,input-colorspace and adi,input-clock are required except in
# "rgb 1x" and "yuv444 1x" modes, in which case they must not be
# specified.
if:
not:
properties:
adi,input-colorspace:
contains:
enum: [ rgb, yuv444 ]
adi,input-clock:
contains:
const: 1x
then:
required:
- adi,input-style
- adi,input-justification
else:
properties:
adi,input-style: false
adi,input-justification: false
required:
- compatible
- reg
- ports
- adi,input-depth
- adi,input-colorspace
- adi,input-clock
- avdd-supply
- dvdd-supply
- pvdd-supply
- dvdd-3v-supply
- bgvdd-supply
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/irq.h>
i2c@e6500000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0 0xe6500000>;
adv7511w: hdmi@39 {
compatible = "adi,adv7511w";
/*
* The EDID page will be accessible on address 0x66 on the I2C
* bus. All other maps continue to use their default addresses.
*/
reg = <0x39>, <0x66>;
reg-names = "main", "edid";
interrupt-parent = <&gpio3>;
interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
clocks = <&cec_clock>;
clock-names = "cec";
avdd-supply = <&v1v8>;
dvdd-supply = <&v1v8>;
pvdd-supply = <&v1v8>;
dvdd-3v-supply = <&v3v3>;
bgvdd-supply = <&v1v8>;
adi,input-depth = <8>;
adi,input-colorspace = "yuv422";
adi,input-clock = "1x";
adi,input-style = <3>;
adi,input-justification = "right";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511w_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
port@2 {
reg = <2>;
codec_endpoint: endpoint {
remote-endpoint = <&i2s0_cpu_endpoint>;
};
};
};
};
};
...