| /* |
| * at91sam9rl.dtsi - Device Tree Include file for AT91SAM9RL family SoC |
| * |
| * Copyright (C) 2014 Alexandre Belloni <alexandre.belloni@free-electrons.com> |
| * |
| * Licensed under GPLv2 or later. |
| */ |
| |
| #include "skeleton.dtsi" |
| #include <dt-bindings/pinctrl/at91.h> |
| #include <dt-bindings/clock/at91.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/pwm/pwm.h> |
| |
| / { |
| model = "Atmel AT91SAM9RL family SoC"; |
| compatible = "atmel,at91sam9rl", "atmel,at91sam9"; |
| interrupt-parent = <&aic>; |
| |
| aliases { |
| serial0 = &dbgu; |
| serial1 = &usart0; |
| serial2 = &usart1; |
| serial3 = &usart2; |
| serial4 = &usart3; |
| gpio0 = &pioA; |
| gpio1 = &pioB; |
| gpio2 = &pioC; |
| gpio3 = &pioD; |
| tcb0 = &tcb0; |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| ssc0 = &ssc0; |
| ssc1 = &ssc1; |
| pwm0 = &pwm0; |
| }; |
| |
| cpus { |
| #address-cells = <0>; |
| #size-cells = <0>; |
| |
| cpu { |
| compatible = "arm,arm926ej-s"; |
| device_type = "cpu"; |
| }; |
| }; |
| |
| memory { |
| reg = <0x20000000 0x04000000>; |
| }; |
| |
| clocks { |
| slow_xtal: slow_xtal { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| }; |
| |
| main_xtal: main_xtal { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| }; |
| |
| adc_op_clk: adc_op_clk{ |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <1000000>; |
| }; |
| }; |
| |
| sram: sram@00300000 { |
| compatible = "mmio-sram"; |
| reg = <0x00300000 0x10000>; |
| }; |
| |
| ahb { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| fb0: fb@00500000 { |
| compatible = "atmel,at91sam9rl-lcdc"; |
| reg = <0x00500000 0x1000>; |
| interrupts = <23 IRQ_TYPE_LEVEL_HIGH 3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fb>; |
| clocks = <&lcd_clk>, <&lcd_clk>; |
| clock-names = "hclk", "lcdc_clk"; |
| status = "disabled"; |
| }; |
| |
| nand0: nand@40000000 { |
| compatible = "atmel,at91rm9200-nand"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x40000000 0x10000000>, |
| <0xffffe800 0x200>; |
| atmel,nand-addr-offset = <21>; |
| atmel,nand-cmd-offset = <22>; |
| atmel,nand-has-dma; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_nand>; |
| gpios = <&pioD 17 GPIO_ACTIVE_HIGH>, |
| <&pioB 6 GPIO_ACTIVE_HIGH>, |
| <0>; |
| status = "disabled"; |
| }; |
| |
| apb { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| tcb0: timer@fffa0000 { |
| compatible = "atmel,at91rm9200-tcb"; |
| reg = <0xfffa0000 0x100>; |
| interrupts = <16 IRQ_TYPE_LEVEL_HIGH 0>, |
| <17 IRQ_TYPE_LEVEL_HIGH 0>, |
| <18 IRQ_TYPE_LEVEL_HIGH 0>; |
| clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>; |
| clock-names = "t0_clk", "t1_clk", "t2_clk"; |
| }; |
| |
| mmc0: mmc@fffa4000 { |
| compatible = "atmel,hsmci"; |
| reg = <0xfffa4000 0x600>; |
| interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-names = "default"; |
| clocks = <&mci0_clk>; |
| clock-names = "mci_clk"; |
| status = "disabled"; |
| }; |
| |
| i2c0: i2c@fffa8000 { |
| compatible = "atmel,at91sam9260-i2c"; |
| reg = <0xfffa8000 0x100>; |
| interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&twi0_clk>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@fffac000 { |
| compatible = "atmel,at91sam9260-i2c"; |
| reg = <0xfffac000 0x100>; |
| interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| usart0: serial@fffb0000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xfffb0000 0x200>; |
| interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; |
| atmel,use-dma-rx; |
| atmel,use-dma-tx; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart0>; |
| clocks = <&usart0_clk>; |
| clock-names = "usart"; |
| status = "disabled"; |
| }; |
| |
| usart1: serial@fffb4000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xfffb4000 0x200>; |
| interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; |
| atmel,use-dma-rx; |
| atmel,use-dma-tx; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart1>; |
| clocks = <&usart1_clk>; |
| clock-names = "usart"; |
| status = "disabled"; |
| }; |
| |
| usart2: serial@fffb8000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xfffb8000 0x200>; |
| interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; |
| atmel,use-dma-rx; |
| atmel,use-dma-tx; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart2>; |
| clocks = <&usart2_clk>; |
| clock-names = "usart"; |
| status = "disabled"; |
| }; |
| |
| usart3: serial@fffbc000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xfffbc000 0x200>; |
| interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>; |
| atmel,use-dma-rx; |
| atmel,use-dma-tx; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart3>; |
| clocks = <&usart3_clk>; |
| clock-names = "usart"; |
| status = "disabled"; |
| }; |
| |
| ssc0: ssc@fffc0000 { |
| compatible = "atmel,at91sam9rl-ssc"; |
| reg = <0xfffc0000 0x4000>; |
| interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; |
| status = "disabled"; |
| }; |
| |
| ssc1: ssc@fffc4000 { |
| compatible = "atmel,at91sam9rl-ssc"; |
| reg = <0xfffc4000 0x4000>; |
| interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; |
| status = "disabled"; |
| }; |
| |
| pwm0: pwm@fffc8000 { |
| compatible = "atmel,at91sam9rl-pwm"; |
| reg = <0xfffc8000 0x300>; |
| interrupts = <19 IRQ_TYPE_LEVEL_HIGH 4>; |
| #pwm-cells = <3>; |
| clocks = <&pwm_clk>; |
| clock-names = "pwm_clk"; |
| status = "disabled"; |
| }; |
| |
| spi0: spi@fffcc000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "atmel,at91rm9200-spi"; |
| reg = <0xfffcc000 0x200>; |
| interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi0>; |
| clocks = <&spi0_clk>; |
| clock-names = "spi_clk"; |
| status = "disabled"; |
| }; |
| |
| adc0: adc@fffd0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "atmel,at91sam9rl-adc"; |
| reg = <0xfffd0000 0x100>; |
| interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; |
| clocks = <&adc_clk>, <&adc_op_clk>; |
| clock-names = "adc_clk", "adc_op_clk"; |
| atmel,adc-use-external-triggers; |
| atmel,adc-channels-used = <0x3f>; |
| atmel,adc-vref = <3300>; |
| atmel,adc-startup-time = <40>; |
| atmel,adc-res = <8 10>; |
| atmel,adc-res-names = "lowres", "highres"; |
| atmel,adc-use-res = "highres"; |
| |
| trigger@0 { |
| reg = <0>; |
| trigger-name = "timer-counter-0"; |
| trigger-value = <0x1>; |
| }; |
| trigger@1 { |
| reg = <1>; |
| trigger-name = "timer-counter-1"; |
| trigger-value = <0x3>; |
| }; |
| |
| trigger@2 { |
| reg = <2>; |
| trigger-name = "timer-counter-2"; |
| trigger-value = <0x5>; |
| }; |
| |
| trigger@3 { |
| reg = <3>; |
| trigger-name = "external"; |
| trigger-value = <0x13>; |
| trigger-external; |
| }; |
| }; |
| |
| usb0: gadget@fffd4000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "atmel,at91sam9rl-udc"; |
| reg = <0x00600000 0x100000>, |
| <0xfffd4000 0x4000>; |
| interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>; |
| clocks = <&udphs_clk>, <&utmi>; |
| clock-names = "pclk", "hclk"; |
| status = "disabled"; |
| |
| ep0 { |
| reg = <0>; |
| atmel,fifo-size = <64>; |
| atmel,nb-banks = <1>; |
| }; |
| |
| ep1 { |
| reg = <1>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <2>; |
| atmel,can-dma; |
| atmel,can-isoc; |
| }; |
| |
| ep2 { |
| reg = <2>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <2>; |
| atmel,can-dma; |
| atmel,can-isoc; |
| }; |
| |
| ep3 { |
| reg = <3>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <3>; |
| atmel,can-dma; |
| }; |
| |
| ep4 { |
| reg = <4>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <3>; |
| atmel,can-dma; |
| }; |
| |
| ep5 { |
| reg = <5>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <3>; |
| atmel,can-dma; |
| atmel,can-isoc; |
| }; |
| |
| ep6 { |
| reg = <6>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <3>; |
| atmel,can-dma; |
| atmel,can-isoc; |
| }; |
| }; |
| |
| dma0: dma-controller@ffffe600 { |
| compatible = "atmel,at91sam9rl-dma"; |
| reg = <0xffffe600 0x200>; |
| interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>; |
| #dma-cells = <2>; |
| clocks = <&dma0_clk>; |
| clock-names = "dma_clk"; |
| }; |
| |
| ramc0: ramc@ffffea00 { |
| compatible = "atmel,at91sam9260-sdramc"; |
| reg = <0xffffea00 0x200>; |
| }; |
| |
| aic: interrupt-controller@fffff000 { |
| #interrupt-cells = <3>; |
| compatible = "atmel,at91rm9200-aic"; |
| interrupt-controller; |
| reg = <0xfffff000 0x200>; |
| atmel,external-irqs = <31>; |
| }; |
| |
| dbgu: serial@fffff200 { |
| compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; |
| reg = <0xfffff200 0x200>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_dbgu>; |
| clocks = <&mck>; |
| clock-names = "usart"; |
| status = "disabled"; |
| }; |
| |
| pinctrl@fffff400 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; |
| ranges = <0xfffff400 0xfffff400 0x800>; |
| |
| atmel,mux-mask = |
| /* A B */ |
| <0xffffffff 0xe05c6738>, /* pioA */ |
| <0xffffffff 0x0000c780>, /* pioB */ |
| <0xffffffff 0xe3ffff0e>, /* pioC */ |
| <0x003fffff 0x0001ff3c>; /* pioD */ |
| |
| /* shared pinctrl settings */ |
| adc0 { |
| pinctrl_adc0_ts: adc0_ts-0 { |
| atmel,pins = |
| <AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_adc0_ad0: adc0_ad0-0 { |
| atmel,pins = <AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_adc0_ad1: adc0_ad1-0 { |
| atmel,pins = <AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_adc0_ad2: adc0_ad2-0 { |
| atmel,pins = <AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_adc0_ad3: adc0_ad3-0 { |
| atmel,pins = <AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_adc0_ad4: adc0_ad4-0 { |
| atmel,pins = <AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_adc0_ad5: adc0_ad5-0 { |
| atmel,pins = <AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_adc0_adtrg: adc0_adtrg-0 { |
| atmel,pins = <AT91_PIOB 15 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| dbgu { |
| pinctrl_dbgu: dbgu-0 { |
| atmel,pins = |
| <AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOA 22 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; |
| }; |
| }; |
| |
| fb { |
| pinctrl_fb: fb-0 { |
| atmel,pins = |
| <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 12 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 13 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 15 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 16 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 17 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 18 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 19 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 20 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 21 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOC 25 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| i2c_gpio0 { |
| pinctrl_i2c_gpio0: i2c_gpio0-0 { |
| atmel,pins = |
| <AT91_PIOA 23 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>, |
| <AT91_PIOA 24 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>; |
| }; |
| }; |
| |
| i2c_gpio1 { |
| pinctrl_i2c_gpio1: i2c_gpio1-0 { |
| atmel,pins = |
| <AT91_PIOD 10 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>, |
| <AT91_PIOD 11 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>; |
| }; |
| }; |
| |
| mmc0 { |
| pinctrl_mmc0_clk: mmc0_clk-0 { |
| atmel,pins = |
| <AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_mmc0_slot0_cmd_dat0: mmc0_slot0_cmd_dat0-0 { |
| atmel,pins = |
| <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>, |
| <AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; |
| }; |
| |
| pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 { |
| atmel,pins = |
| <AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>, |
| <AT91_PIOA 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>, |
| <AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; |
| }; |
| }; |
| |
| nand { |
| pinctrl_nand: nand-0 { |
| atmel,pins = |
| <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>, |
| <AT91_PIOB 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; |
| }; |
| |
| pinctrl_nand0_ale_cle: nand_ale_cle-0 { |
| atmel,pins = |
| <AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_nand0_oe_we: nand_oe_we-0 { |
| atmel,pins = |
| <AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_nand0_cs: nand_cs-0 { |
| atmel,pins = |
| <AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| pwm0 { |
| pinctrl_pwm0_pwm0_0: pwm0_pwm0-0 { |
| atmel,pins = <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_pwm0_pwm0_1: pwm0_pwm0-1 { |
| atmel,pins = <AT91_PIOC 2 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_pwm0_pwm0_2: pwm0_pwm0-2 { |
| atmel,pins = <AT91_PIOD 14 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_pwm0_pwm1_0: pwm0_pwm1-0 { |
| atmel,pins = <AT91_PIOB 9 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_pwm0_pwm1_1: pwm0_pwm1-1 { |
| atmel,pins = <AT91_PIOC 3 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_pwm0_pwm1_2: pwm0_pwm1-2 { |
| atmel,pins = <AT91_PIOD 15 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_pwm0_pwm2_0: pwm0_pwm2-0 { |
| atmel,pins = <AT91_PIOD 5 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_pwm0_pwm2_1: pwm0_pwm2-1 { |
| atmel,pins = <AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_pwm0_pwm2_2: pwm0_pwm2-2 { |
| atmel,pins = <AT91_PIOD 16 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_pwm0_pwm3_0: pwm0_pwm3-0 { |
| atmel,pins = <AT91_PIOD 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_pwm0_pwm3_1: pwm0_pwm3-1 { |
| atmel,pins = <AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| spi0 { |
| pinctrl_spi0: spi0-0 { |
| atmel,pins = |
| <AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| ssc0 { |
| pinctrl_ssc0_tx: ssc0_tx-0 { |
| atmel,pins = |
| <AT91_PIOA 15 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOC 0 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOC 1 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_ssc0_rx: ssc0_rx-0 { |
| atmel,pins = |
| <AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOA 16 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| ssc1 { |
| pinctrl_ssc1_tx: ssc1_tx-0 { |
| atmel,pins = |
| <AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOA 29 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOA 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_ssc1_rx: ssc1_rx-0 { |
| atmel,pins = |
| <AT91_PIOA 8 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE>, |
| <AT91_PIOA 14 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| tcb0 { |
| pinctrl_tcb0_tclk0: tcb0_tclk0-0 { |
| atmel,pins = <AT91_PIOA 3 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tclk1: tcb0_tclk1-0 { |
| atmel,pins = <AT91_PIOC 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tclk2: tcb0_tclk2-0 { |
| atmel,pins = <AT91_PIOD 21 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tioa0: tcb0_tioa0-0 { |
| atmel,pins = <AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tioa1: tcb0_tioa1-0 { |
| atmel,pins = <AT91_PIOC 29 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tioa2: tcb0_tioa2-0 { |
| atmel,pins = <AT91_PIOD 10 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tiob0: tcb0_tiob0-0 { |
| atmel,pins = <AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tiob1: tcb0_tiob1-0 { |
| atmel,pins = <AT91_PIOC 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tiob2: tcb0_tiob2-0 { |
| atmel,pins = <AT91_PIOD 11 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| usart0 { |
| pinctrl_usart0: usart0-0 { |
| atmel,pins = |
| <AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; |
| }; |
| |
| pinctrl_usart0_rts: usart0_rts-0 { |
| atmel,pins = |
| <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart0_cts: usart0_cts-0 { |
| atmel,pins = |
| <AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart0_dtr_dsr: usart0_dtr_dsr-0 { |
| atmel,pins = |
| <AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_NONE>, |
| <AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart0_dcd: usart0_dcd-0 { |
| atmel,pins = |
| <AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart0_ri: usart0_ri-0 { |
| atmel,pins = |
| <AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart0_sck: usart0_sck-0 { |
| atmel,pins = |
| <AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| usart1 { |
| pinctrl_usart1: usart1-0 { |
| atmel,pins = |
| <AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>, |
| <AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart1_rts: usart1_rts-0 { |
| atmel,pins = |
| <AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart1_cts: usart1_cts-0 { |
| atmel,pins = |
| <AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart1_sck: usart1_sck-0 { |
| atmel,pins = |
| <AT91_PIOD 2 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| usart2 { |
| pinctrl_usart2: usart2-0 { |
| atmel,pins = |
| <AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>, |
| <AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart2_rts: usart2_rts-0 { |
| atmel,pins = |
| <AT91_PIOA 29 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart2_cts: usart2_cts-0 { |
| atmel,pins = |
| <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart2_sck: usart2_sck-0 { |
| atmel,pins = |
| <AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| usart3 { |
| pinctrl_usart3: usart3-0 { |
| atmel,pins = |
| <AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>, |
| <AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart3_rts: usart3_rts-0 { |
| atmel,pins = |
| <AT91_PIOD 4 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart3_cts: usart3_cts-0 { |
| atmel,pins = |
| <AT91_PIOD 3 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_usart3_sck: usart3_sck-0 { |
| atmel,pins = |
| <AT91_PIOA 20 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| pioA: gpio@fffff400 { |
| compatible = "atmel,at91rm9200-gpio"; |
| reg = <0xfffff400 0x200>; |
| interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pioA_clk>; |
| }; |
| |
| pioB: gpio@fffff600 { |
| compatible = "atmel,at91rm9200-gpio"; |
| reg = <0xfffff600 0x200>; |
| interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pioB_clk>; |
| }; |
| |
| pioC: gpio@fffff800 { |
| compatible = "atmel,at91rm9200-gpio"; |
| reg = <0xfffff800 0x200>; |
| interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pioC_clk>; |
| }; |
| |
| pioD: gpio@fffffa00 { |
| compatible = "atmel,at91rm9200-gpio"; |
| reg = <0xfffffa00 0x200>; |
| interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pioD_clk>; |
| }; |
| }; |
| |
| pmc: pmc@fffffc00 { |
| compatible = "atmel,at91sam9g45-pmc"; |
| reg = <0xfffffc00 0x100>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| interrupt-controller; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| main: mainck { |
| compatible = "atmel,at91rm9200-clk-main"; |
| #clock-cells = <0>; |
| interrupts-extended = <&pmc AT91_PMC_MOSCS>; |
| clocks = <&main_xtal>; |
| }; |
| |
| plla: pllack { |
| compatible = "atmel,at91rm9200-clk-pll"; |
| #clock-cells = <0>; |
| interrupts-extended = <&pmc AT91_PMC_LOCKA>; |
| clocks = <&main>; |
| reg = <0>; |
| atmel,clk-input-range = <1000000 32000000>; |
| #atmel,pll-clk-output-range-cells = <3>; |
| atmel,pll-clk-output-ranges = <80000000 200000000 0>, |
| <190000000 240000000 2>; |
| }; |
| |
| utmi: utmick { |
| compatible = "atmel,at91sam9x5-clk-utmi"; |
| #clock-cells = <0>; |
| interrupt-parent = <&pmc>; |
| interrupts = <AT91_PMC_LOCKU>; |
| clocks = <&main>; |
| }; |
| |
| mck: masterck { |
| compatible = "atmel,at91rm9200-clk-master"; |
| #clock-cells = <0>; |
| interrupts-extended = <&pmc AT91_PMC_MCKRDY>; |
| clocks = <&clk32k>, <&main>, <&plla>, <&utmi>; |
| atmel,clk-output-range = <0 94000000>; |
| atmel,clk-divisors = <1 2 4 0>; |
| }; |
| |
| prog: progck { |
| compatible = "atmel,at91rm9200-clk-programmable"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupt-parent = <&pmc>; |
| clocks = <&clk32k>, <&main>, <&plla>, <&utmi>, <&mck>; |
| |
| prog0: prog0 { |
| #clock-cells = <0>; |
| reg = <0>; |
| interrupts = <AT91_PMC_PCKRDY(0)>; |
| }; |
| |
| prog1: prog1 { |
| #clock-cells = <0>; |
| reg = <1>; |
| interrupts = <AT91_PMC_PCKRDY(1)>; |
| }; |
| }; |
| |
| systemck { |
| compatible = "atmel,at91rm9200-clk-system"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pck0: pck0 { |
| #clock-cells = <0>; |
| reg = <8>; |
| clocks = <&prog0>; |
| }; |
| |
| pck1: pck1 { |
| #clock-cells = <0>; |
| reg = <9>; |
| clocks = <&prog1>; |
| }; |
| |
| }; |
| |
| periphck { |
| compatible = "atmel,at91rm9200-clk-peripheral"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&mck>; |
| |
| pioA_clk: pioA_clk { |
| #clock-cells = <0>; |
| reg = <2>; |
| }; |
| |
| pioB_clk: pioB_clk { |
| #clock-cells = <0>; |
| reg = <3>; |
| }; |
| |
| pioC_clk: pioC_clk { |
| #clock-cells = <0>; |
| reg = <4>; |
| }; |
| |
| pioD_clk: pioD_clk { |
| #clock-cells = <0>; |
| reg = <5>; |
| }; |
| |
| usart0_clk: usart0_clk { |
| #clock-cells = <0>; |
| reg = <6>; |
| }; |
| |
| usart1_clk: usart1_clk { |
| #clock-cells = <0>; |
| reg = <7>; |
| }; |
| |
| usart2_clk: usart2_clk { |
| #clock-cells = <0>; |
| reg = <8>; |
| }; |
| |
| usart3_clk: usart3_clk { |
| #clock-cells = <0>; |
| reg = <9>; |
| }; |
| |
| mci0_clk: mci0_clk { |
| #clock-cells = <0>; |
| reg = <10>; |
| }; |
| |
| twi0_clk: twi0_clk { |
| #clock-cells = <0>; |
| reg = <11>; |
| }; |
| |
| twi1_clk: twi1_clk { |
| #clock-cells = <0>; |
| reg = <12>; |
| }; |
| |
| spi0_clk: spi0_clk { |
| #clock-cells = <0>; |
| reg = <13>; |
| }; |
| |
| ssc0_clk: ssc0_clk { |
| #clock-cells = <0>; |
| reg = <14>; |
| }; |
| |
| ssc1_clk: ssc1_clk { |
| #clock-cells = <0>; |
| reg = <15>; |
| }; |
| |
| tc0_clk: tc0_clk { |
| #clock-cells = <0>; |
| reg = <16>; |
| }; |
| |
| tc1_clk: tc1_clk { |
| #clock-cells = <0>; |
| reg = <17>; |
| }; |
| |
| tc2_clk: tc2_clk { |
| #clock-cells = <0>; |
| reg = <18>; |
| }; |
| |
| pwm_clk: pwm_clk { |
| #clock-cells = <0>; |
| reg = <19>; |
| }; |
| |
| adc_clk: adc_clk { |
| #clock-cells = <0>; |
| reg = <20>; |
| }; |
| |
| dma0_clk: dma0_clk { |
| #clock-cells = <0>; |
| reg = <21>; |
| }; |
| |
| udphs_clk: udphs_clk { |
| #clock-cells = <0>; |
| reg = <22>; |
| }; |
| |
| lcd_clk: lcd_clk { |
| #clock-cells = <0>; |
| reg = <23>; |
| }; |
| }; |
| }; |
| |
| rstc@fffffd00 { |
| compatible = "atmel,at91sam9260-rstc"; |
| reg = <0xfffffd00 0x10>; |
| }; |
| |
| shdwc@fffffd10 { |
| compatible = "atmel,at91sam9260-shdwc"; |
| reg = <0xfffffd10 0x10>; |
| }; |
| |
| pit: timer@fffffd30 { |
| compatible = "atmel,at91sam9260-pit"; |
| reg = <0xfffffd30 0xf>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| clocks = <&mck>; |
| }; |
| |
| watchdog@fffffd40 { |
| compatible = "atmel,at91sam9260-wdt"; |
| reg = <0xfffffd40 0x10>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| status = "disabled"; |
| }; |
| |
| sckc@fffffd50 { |
| compatible = "atmel,at91sam9x5-sckc"; |
| reg = <0xfffffd50 0x4>; |
| |
| slow_osc: slow_osc { |
| compatible = "atmel,at91sam9x5-clk-slow-osc"; |
| #clock-cells = <0>; |
| atmel,startup-time-usec = <1200000>; |
| clocks = <&slow_xtal>; |
| }; |
| |
| slow_rc_osc: slow_rc_osc { |
| compatible = "atmel,at91sam9x5-clk-slow-rc-osc"; |
| #clock-cells = <0>; |
| atmel,startup-time-usec = <75>; |
| clock-frequency = <32768>; |
| clock-accuracy = <50000000>; |
| }; |
| |
| clk32k: slck { |
| compatible = "atmel,at91sam9x5-clk-slow"; |
| #clock-cells = <0>; |
| clocks = <&slow_rc_osc &slow_osc>; |
| }; |
| }; |
| |
| rtc@fffffeb0 { |
| compatible = "atmel,at91rm9200-rtc"; |
| reg = <0xfffffeb0 0x40>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| status = "disabled"; |
| }; |
| |
| rtc@fffffd20 { |
| compatible = "atmel,at91sam9260-rtt"; |
| reg = <0xfffffd20 0x10>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| clocks = <&clk32k>; |
| status = "disabled"; |
| }; |
| |
| gpbr: syscon@fffffd60 { |
| compatible = "atmel,at91sam9260-gpbr", "syscon"; |
| reg = <0xfffffd60 0x10>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| i2c@0 { |
| compatible = "i2c-gpio"; |
| gpios = <&pioA 23 GPIO_ACTIVE_HIGH>, /* sda */ |
| <&pioA 24 GPIO_ACTIVE_HIGH>; /* scl */ |
| i2c-gpio,sda-open-drain; |
| i2c-gpio,scl-open-drain; |
| i2c-gpio,delay-us = <2>; /* ~100 kHz */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c_gpio0>; |
| status = "disabled"; |
| }; |
| |
| i2c@1 { |
| compatible = "i2c-gpio"; |
| gpios = <&pioD 10 GPIO_ACTIVE_HIGH>, /* sda */ |
| <&pioD 11 GPIO_ACTIVE_HIGH>; /* scl */ |
| i2c-gpio,sda-open-drain; |
| i2c-gpio,scl-open-drain; |
| i2c-gpio,delay-us = <2>; /* ~100 kHz */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c_gpio1>; |
| status = "disabled"; |
| }; |
| }; |
