| .. SPDX-License-Identifier: GPL-2.0-or-later |
| |
| .. include:: <isonum.txt> |
| |
| Kernel driver dell-smm-hwmon |
| ============================ |
| |
| :Copyright: |copy| 2002-2005 Massimo Dal Zotto <dz@debian.org> |
| :Copyright: |copy| 2019 Giovanni Mascellani <gio@debian.org> |
| |
| Description |
| ----------- |
| |
| On many Dell laptops the System Management Mode (SMM) BIOS can be |
| queried for the status of fans and temperature sensors. Userspace |
| utilities like ``sensors`` can be used to return the readings. The |
| userspace suite `i8kutils`__ can also be used to read the sensors and |
| automatically adjust fan speed (please notice that it currently uses |
| the deprecated ``/proc/i8k`` interface). |
| |
| __ https://github.com/vitorafsr/i8kutils |
| |
| ``sysfs`` interface |
| ------------------- |
| |
| Temperature sensors and fans can be queried and set via the standard |
| ``hwmon`` interface on ``sysfs``, under the directory |
| ``/sys/class/hwmon/hwmonX`` for some value of ``X`` (search for the |
| ``X`` such that ``/sys/class/hwmon/hwmonX/name`` has content |
| ``dell_smm``). A number of other attributes can be read or written: |
| |
| =============================== ======= ======================================= |
| Name Perm Description |
| =============================== ======= ======================================= |
| fan[1-3]_input RO Fan speed in RPM. |
| fan[1-3]_label RO Fan label. |
| fan[1-3]_min RO Minimal Fan speed in RPM |
| fan[1-3]_max RO Maximal Fan speed in RPM |
| fan[1-3]_target RO Expected Fan speed in RPM |
| pwm[1-3] RW Control the fan PWM duty-cycle. |
| pwm1_enable WO Enable or disable automatic BIOS fan |
| control (not supported on all laptops, |
| see below for details). |
| temp[1-10]_input RO Temperature reading in milli-degrees |
| Celsius. |
| temp[1-10]_label RO Temperature sensor label. |
| =============================== ======= ======================================= |
| |
| Disabling automatic BIOS fan control |
| ------------------------------------ |
| |
| On some laptops the BIOS automatically sets fan speed every few |
| seconds. Therefore the fan speed set by mean of this driver is quickly |
| overwritten. |
| |
| There is experimental support for disabling automatic BIOS fan |
| control, at least on laptops where the corresponding SMM command is |
| known, by writing the value ``1`` in the attribute ``pwm1_enable`` |
| (writing ``2`` enables automatic BIOS control again). Even if you have |
| more than one fan, all of them are set to either enabled or disabled |
| automatic fan control at the same time and, notwithstanding the name, |
| ``pwm1_enable`` sets automatic control for all fans. |
| |
| If ``pwm1_enable`` is not available, then it means that SMM codes for |
| enabling and disabling automatic BIOS fan control are not whitelisted |
| for your hardware. It is possible that codes that work for other |
| laptops actually work for yours as well, or that you have to discover |
| new codes. |
| |
| Check the list ``i8k_whitelist_fan_control`` in file |
| ``drivers/hwmon/dell-smm-hwmon.c`` in the kernel tree: as a first |
| attempt you can try to add your machine and use an already-known code |
| pair. If, after recompiling the kernel, you see that ``pwm1_enable`` |
| is present and works (i.e., you can manually control the fan speed), |
| then please submit your finding as a kernel patch, so that other users |
| can benefit from it. Please see |
| :ref:`Documentation/process/submitting-patches.rst <submittingpatches>` |
| for information on submitting patches. |
| |
| If no known code works on your machine, you need to resort to do some |
| probing, because unfortunately Dell does not publish datasheets for |
| its SMM. You can experiment with the code in `this repository`__ to |
| probe the BIOS on your machine and discover the appropriate codes. |
| |
| __ https://github.com/clopez/dellfan/ |
| |
| Again, when you find new codes, we'd be happy to have your patches! |
| |
| Module parameters |
| ----------------- |
| |
| * force:bool |
| Force loading without checking for supported |
| models. (default: 0) |
| |
| * ignore_dmi:bool |
| Continue probing hardware even if DMI data does not |
| match. (default: 0) |
| |
| * restricted:bool |
| Allow fan control only to processes with the |
| ``CAP_SYS_ADMIN`` capability set or processes run |
| as root when using the legacy ``/proc/i8k`` |
| interface. In this case normal users will be able |
| to read temperature and fan status but not to |
| control the fan. If your notebook is shared with |
| other users and you don't trust them you may want |
| to use this option. (default: 1, only available |
| with ``CONFIG_I8K``) |
| |
| * power_status:bool |
| Report AC status in ``/proc/i8k``. (default: 0, |
| only available with ``CONFIG_I8K``) |
| |
| * fan_mult:uint |
| Factor to multiply fan speed with. (default: |
| autodetect) |
| |
| * fan_max:uint |
| Maximum configurable fan speed. (default: |
| autodetect) |
| |
| Legacy ``/proc`` interface |
| -------------------------- |
| |
| .. warning:: This interface is obsolete and deprecated and should not |
| used in new applications. This interface is only |
| available when kernel is compiled with option |
| ``CONFIG_I8K``. |
| |
| The information provided by the kernel driver can be accessed by |
| simply reading the ``/proc/i8k`` file. For example:: |
| |
| $ cat /proc/i8k |
| 1.0 A17 2J59L02 52 2 1 8040 6420 1 2 |
| |
| The fields read from ``/proc/i8k`` are:: |
| |
| 1.0 A17 2J59L02 52 2 1 8040 6420 1 2 |
| | | | | | | | | | | |
| | | | | | | | | | +------- 10. buttons status |
| | | | | | | | | +--------- 9. AC status |
| | | | | | | | +-------------- 8. fan0 RPM |
| | | | | | | +------------------- 7. fan1 RPM |
| | | | | | +--------------------- 6. fan0 status |
| | | | | +----------------------- 5. fan1 status |
| | | | +-------------------------- 4. temp0 reading (Celsius) |
| | | +---------------------------------- 3. Dell service tag (later known as 'serial number') |
| | +-------------------------------------- 2. BIOS version |
| +------------------------------------------ 1. /proc/i8k format version |
| |
| A negative value, for example -22, indicates that the BIOS doesn't |
| return the corresponding information. This is normal on some |
| models/BIOSes. |
| |
| For performance reasons the ``/proc/i8k`` doesn't report by default |
| the AC status since this SMM call takes a long time to execute and is |
| not really needed. If you want to see the ac status in ``/proc/i8k`` |
| you must explictitly enable this option by passing the |
| ``power_status=1`` parameter to insmod. If AC status is not |
| available -1 is printed instead. |
| |
| The driver provides also an ioctl interface which can be used to |
| obtain the same information and to control the fan status. The ioctl |
| interface can be accessed from C programs or from shell using the |
| i8kctl utility. See the source file of ``i8kutils`` for more |
| information on how to use the ioctl interface. |
| |
| SMM Interface |
| ------------- |
| |
| .. warning:: The SMM interface was reverse-engineered by trial-and-error |
| since Dell did not provide any Documentation, |
| please keep that in mind. |
| |
| The driver uses the SMM interface to send commands to the system BIOS. |
| This interface is normally used by Dell's 32-bit diagnostic program or |
| on newer notebook models by the buildin BIOS diagnostics. |
| The SMM is triggered by writing to the special ioports ``0xb2`` and ``0x84``, |
| and may cause short hangs when the BIOS code is taking too long to |
| execute. |
| |
| The SMM handler inside the system BIOS looks at the contents of the |
| ``eax``, ``ebx``, ``ecx``, ``edx``, ``esi`` and ``edi`` registers. |
| Each register has a special purpose: |
| |
| =============== ================================== |
| Register Purpose |
| =============== ================================== |
| eax Holds the command code before SMM, |
| holds the first result after SMM. |
| ebx Holds the arguments. |
| ecx Unknown, set to 0. |
| edx Holds the second result after SMM. |
| esi Unknown, set to 0. |
| edi Unknown, set to 0. |
| =============== ================================== |
| |
| The SMM handler can signal a failure by either: |
| |
| - setting the lower sixteen bits of ``eax`` to ``0xffff`` |
| - not modifying ``eax`` at all |
| - setting the carry flag |
| |
| SMM command codes |
| ----------------- |
| |
| =============== ======================= ================================================ |
| Command Code Command Name Description |
| =============== ======================= ================================================ |
| ``0x0025`` Get Fn key status Returns the Fn key pressed after SMM: |
| |
| - 9th bit in ``eax`` indicates Volume up |
| - 10th bit in ``eax`` indicates Volume down |
| - both bits indicate Volume mute |
| |
| ``0xa069`` Get power status Returns current power status after SMM: |
| |
| - 1st bit in ``eax`` indicates Battery connected |
| - 3th bit in ``eax`` indicates AC connected |
| |
| ``0x00a3`` Get fan state Returns current fan state after SMM: |
| |
| - 1st byte in ``eax`` holds the current |
| fan state (0 - 2 or 3) |
| |
| ``0x01a3`` Set fan state Sets the fan speed: |
| |
| - 1st byte in ``ebx`` holds the fan number |
| - 2nd byte in ``ebx`` holds the desired |
| fan state (0 - 2 or 3) |
| |
| ``0x02a3`` Get fan speed Returns the current fan speed in RPM: |
| |
| - 1st byte in ``ebx`` holds the fan number |
| - 1st word in ``eax`` holds the current |
| fan speed in RPM (after SMM) |
| |
| ``0x03a3`` Get fan type Returns the fan type: |
| |
| - 1st byte in ``ebx`` holds the fan number |
| - 1st byte in ``eax`` holds the |
| fan type (after SMM): |
| |
| - 5th bit indicates docking fan |
| - 1 indicates Processor fan |
| - 2 indicates Motherboard fan |
| - 3 indicates Video fan |
| - 4 indicates Power supply fan |
| - 5 indicates Chipset fan |
| - 6 indicates other fan type |
| |
| ``0x04a3`` Get nominal fan speed Returns the nominal RPM in each fan state: |
| |
| - 1st byte in ``ebx`` holds the fan number |
| - 2nd byte in ``ebx`` holds the fan state |
| in question (0 - 2 or 3) |
| - 1st word in ``eax`` holds the nominal |
| fan speed in RPM (after SMM) |
| |
| ``0x05a3`` Get fan speed tolerance Returns the speed tolerance for each fan state: |
| |
| - 1st byte in ``ebx`` holds the fan number |
| - 2nd byte in ``ebx`` holds the fan state |
| in question (0 - 2 or 3) |
| - 1st byte in ``eax`` returns the speed |
| tolerance |
| |
| ``0x10a3`` Get sensor temperature Returns the measured temperature: |
| |
| - 1st byte in ``ebx`` holds the sensor number |
| - 1st byte in ``eax`` holds the measured |
| temperature (after SMM) |
| |
| ``0x11a3`` Get sensor type Returns the sensor type: |
| |
| - 1st byte in ``ebx`` holds the sensor number |
| - 1st byte in ``eax`` holds the |
| temperature type (after SMM): |
| |
| - 1 indicates CPU sensor |
| - 2 indicates GPU sensor |
| - 3 indicates SODIMM sensor |
| - 4 indicates other sensor type |
| - 5 indicates Ambient sensor |
| - 6 indicates other sensor type |
| |
| ``0xfea3`` Get SMM signature Returns Dell signature if interface |
| is supported (after SMM): |
| |
| - ``eax`` holds 1145651527 |
| (0x44494147 or "DIAG") |
| - ``edx`` holds 1145392204 |
| (0x44454c4c or "DELL") |
| |
| ``0xffa3`` Get SMM signature Same as ``0xfea3``, check both. |
| =============== ======================= ================================================ |
| |
| There are additional commands for enabling (``0x31a3`` or ``0x35a3``) and |
| disabling (``0x30a3`` or ``0x34a3``) automatic fan speed control. |
| The commands are however causing severe sideeffects on many machines, so |
| they are not used by default. |
| |
| On several machines (Inspiron 3505, Precision 490, Vostro 1720, ...), the |
| fans supports a 4th "magic" state, which signals the BIOS that automatic |
| fan control should be enabled for a specific fan. |
| However there are also some machines who do support a 4th regular fan state too, |
| but in case of the "magic" state, the nominal RPM reported for this state is a |
| placeholder value, which however is not always detectable. |
| |
| Firmware Bugs |
| ------------- |
| |
| The SMM calls can behave erratic on some machines: |
| |
| ======================================================= ================= |
| Firmware Bug Affected Machines |
| ======================================================= ================= |
| Reading of fan states return spurious errors. Precision 490 |
| |
| Reading of fan types causes erratic fan behaviour. Studio XPS 8000 |
| |
| Studio XPS 8100 |
| |
| Inspiron 580 |
| |
| Fan-related SMM calls take too long (about 500ms). Inspiron 7720 |
| |
| Vostro 3360 |
| |
| XPS 13 9333 |
| |
| XPS 15 L502X |
| ======================================================= ================= |
| |
| In case you experience similar issues on your Dell machine, please |
| submit a bugreport on bugzilla to we can apply workarounds. |
| |
| Limitations |
| ----------- |
| |
| The SMM calls can take too long to execute on some machines, causing |
| short hangs and/or audio glitches. |
| Also the fan state needs to be restored after suspend, as well as |
| the automatic mode settings. |
| When reading a temperature sensor, values above 127 degrees indicate |
| a BIOS read error or a deactivated sensor. |