| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * adv7180.c Analog Devices ADV7180 video decoder driver |
| * Copyright (c) 2009 Intel Corporation |
| * Copyright (C) 2013 Cogent Embedded, Inc. |
| * Copyright (C) 2013 Renesas Solutions Corp. |
| */ |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/errno.h> |
| #include <linux/kernel.h> |
| #include <linux/interrupt.h> |
| #include <linux/i2c.h> |
| #include <linux/slab.h> |
| #include <linux/of.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/videodev2.h> |
| #include <media/v4l2-ioctl.h> |
| #include <media/v4l2-event.h> |
| #include <media/v4l2-device.h> |
| #include <media/v4l2-ctrls.h> |
| #include <linux/mutex.h> |
| #include <linux/delay.h> |
| |
| #define ADV7180_STD_AD_PAL_BG_NTSC_J_SECAM 0x0 |
| #define ADV7180_STD_AD_PAL_BG_NTSC_J_SECAM_PED 0x1 |
| #define ADV7180_STD_AD_PAL_N_NTSC_J_SECAM 0x2 |
| #define ADV7180_STD_AD_PAL_N_NTSC_M_SECAM 0x3 |
| #define ADV7180_STD_NTSC_J 0x4 |
| #define ADV7180_STD_NTSC_M 0x5 |
| #define ADV7180_STD_PAL60 0x6 |
| #define ADV7180_STD_NTSC_443 0x7 |
| #define ADV7180_STD_PAL_BG 0x8 |
| #define ADV7180_STD_PAL_N 0x9 |
| #define ADV7180_STD_PAL_M 0xa |
| #define ADV7180_STD_PAL_M_PED 0xb |
| #define ADV7180_STD_PAL_COMB_N 0xc |
| #define ADV7180_STD_PAL_COMB_N_PED 0xd |
| #define ADV7180_STD_PAL_SECAM 0xe |
| #define ADV7180_STD_PAL_SECAM_PED 0xf |
| |
| #define ADV7180_REG_INPUT_CONTROL 0x0000 |
| #define ADV7180_INPUT_CONTROL_INSEL_MASK 0x0f |
| |
| #define ADV7182_REG_INPUT_VIDSEL 0x0002 |
| |
| #define ADV7180_REG_OUTPUT_CONTROL 0x0003 |
| #define ADV7180_REG_EXTENDED_OUTPUT_CONTROL 0x0004 |
| #define ADV7180_EXTENDED_OUTPUT_CONTROL_NTSCDIS 0xC5 |
| |
| #define ADV7180_REG_AUTODETECT_ENABLE 0x0007 |
| #define ADV7180_AUTODETECT_DEFAULT 0x7f |
| /* Contrast */ |
| #define ADV7180_REG_CON 0x0008 /*Unsigned */ |
| #define ADV7180_CON_MIN 0 |
| #define ADV7180_CON_DEF 128 |
| #define ADV7180_CON_MAX 255 |
| /* Brightness*/ |
| #define ADV7180_REG_BRI 0x000a /*Signed */ |
| #define ADV7180_BRI_MIN -128 |
| #define ADV7180_BRI_DEF 0 |
| #define ADV7180_BRI_MAX 127 |
| /* Hue */ |
| #define ADV7180_REG_HUE 0x000b /*Signed, inverted */ |
| #define ADV7180_HUE_MIN -127 |
| #define ADV7180_HUE_DEF 0 |
| #define ADV7180_HUE_MAX 128 |
| |
| #define ADV7180_REG_CTRL 0x000e |
| #define ADV7180_CTRL_IRQ_SPACE 0x20 |
| |
| #define ADV7180_REG_PWR_MAN 0x0f |
| #define ADV7180_PWR_MAN_ON 0x04 |
| #define ADV7180_PWR_MAN_OFF 0x24 |
| #define ADV7180_PWR_MAN_RES 0x80 |
| |
| #define ADV7180_REG_STATUS1 0x0010 |
| #define ADV7180_STATUS1_IN_LOCK 0x01 |
| #define ADV7180_STATUS1_AUTOD_MASK 0x70 |
| #define ADV7180_STATUS1_AUTOD_NTSM_M_J 0x00 |
| #define ADV7180_STATUS1_AUTOD_NTSC_4_43 0x10 |
| #define ADV7180_STATUS1_AUTOD_PAL_M 0x20 |
| #define ADV7180_STATUS1_AUTOD_PAL_60 0x30 |
| #define ADV7180_STATUS1_AUTOD_PAL_B_G 0x40 |
| #define ADV7180_STATUS1_AUTOD_SECAM 0x50 |
| #define ADV7180_STATUS1_AUTOD_PAL_COMB 0x60 |
| #define ADV7180_STATUS1_AUTOD_SECAM_525 0x70 |
| |
| #define ADV7180_REG_IDENT 0x0011 |
| #define ADV7180_ID_7180 0x18 |
| |
| #define ADV7180_REG_STATUS3 0x0013 |
| #define ADV7180_REG_ANALOG_CLAMP_CTL 0x0014 |
| #define ADV7180_REG_SHAP_FILTER_CTL_1 0x0017 |
| #define ADV7180_REG_CTRL_2 0x001d |
| #define ADV7180_REG_VSYNC_FIELD_CTL_1 0x0031 |
| #define ADV7180_VSYNC_FIELD_CTL_1_NEWAV 0x12 |
| #define ADV7180_REG_MANUAL_WIN_CTL_1 0x003d |
| #define ADV7180_REG_MANUAL_WIN_CTL_2 0x003e |
| #define ADV7180_REG_MANUAL_WIN_CTL_3 0x003f |
| #define ADV7180_REG_LOCK_CNT 0x0051 |
| #define ADV7180_REG_CVBS_TRIM 0x0052 |
| #define ADV7180_REG_CLAMP_ADJ 0x005a |
| #define ADV7180_REG_RES_CIR 0x005f |
| #define ADV7180_REG_DIFF_MODE 0x0060 |
| |
| #define ADV7180_REG_ICONF1 0x2040 |
| #define ADV7180_ICONF1_ACTIVE_LOW 0x01 |
| #define ADV7180_ICONF1_PSYNC_ONLY 0x10 |
| #define ADV7180_ICONF1_ACTIVE_TO_CLR 0xC0 |
| /* Saturation */ |
| #define ADV7180_REG_SD_SAT_CB 0x00e3 /*Unsigned */ |
| #define ADV7180_REG_SD_SAT_CR 0x00e4 /*Unsigned */ |
| #define ADV7180_SAT_MIN 0 |
| #define ADV7180_SAT_DEF 128 |
| #define ADV7180_SAT_MAX 255 |
| |
| #define ADV7180_IRQ1_LOCK 0x01 |
| #define ADV7180_IRQ1_UNLOCK 0x02 |
| #define ADV7180_REG_ISR1 0x2042 |
| #define ADV7180_REG_ICR1 0x2043 |
| #define ADV7180_REG_IMR1 0x2044 |
| #define ADV7180_REG_IMR2 0x2048 |
| #define ADV7180_IRQ3_AD_CHANGE 0x08 |
| #define ADV7180_REG_ISR3 0x204A |
| #define ADV7180_REG_ICR3 0x204B |
| #define ADV7180_REG_IMR3 0x204C |
| #define ADV7180_REG_IMR4 0x2050 |
| |
| #define ADV7180_REG_NTSC_V_BIT_END 0x00E6 |
| #define ADV7180_NTSC_V_BIT_END_MANUAL_NVEND 0x4F |
| |
| #define ADV7180_REG_VPP_SLAVE_ADDR 0xFD |
| #define ADV7180_REG_CSI_SLAVE_ADDR 0xFE |
| |
| #define ADV7180_REG_ACE_CTRL1 0x4080 |
| #define ADV7180_REG_ACE_CTRL5 0x4084 |
| #define ADV7180_REG_FLCONTROL 0x40e0 |
| #define ADV7180_FLCONTROL_FL_ENABLE 0x1 |
| |
| #define ADV7180_REG_RST_CLAMP 0x809c |
| #define ADV7180_REG_AGC_ADJ1 0x80b6 |
| #define ADV7180_REG_AGC_ADJ2 0x80c0 |
| |
| #define ADV7180_CSI_REG_PWRDN 0x00 |
| #define ADV7180_CSI_PWRDN 0x80 |
| |
| #define ADV7180_INPUT_CVBS_AIN1 0x00 |
| #define ADV7180_INPUT_CVBS_AIN2 0x01 |
| #define ADV7180_INPUT_CVBS_AIN3 0x02 |
| #define ADV7180_INPUT_CVBS_AIN4 0x03 |
| #define ADV7180_INPUT_CVBS_AIN5 0x04 |
| #define ADV7180_INPUT_CVBS_AIN6 0x05 |
| #define ADV7180_INPUT_SVIDEO_AIN1_AIN2 0x06 |
| #define ADV7180_INPUT_SVIDEO_AIN3_AIN4 0x07 |
| #define ADV7180_INPUT_SVIDEO_AIN5_AIN6 0x08 |
| #define ADV7180_INPUT_YPRPB_AIN1_AIN2_AIN3 0x09 |
| #define ADV7180_INPUT_YPRPB_AIN4_AIN5_AIN6 0x0a |
| |
| #define ADV7182_INPUT_CVBS_AIN1 0x00 |
| #define ADV7182_INPUT_CVBS_AIN2 0x01 |
| #define ADV7182_INPUT_CVBS_AIN3 0x02 |
| #define ADV7182_INPUT_CVBS_AIN4 0x03 |
| #define ADV7182_INPUT_CVBS_AIN5 0x04 |
| #define ADV7182_INPUT_CVBS_AIN6 0x05 |
| #define ADV7182_INPUT_CVBS_AIN7 0x06 |
| #define ADV7182_INPUT_CVBS_AIN8 0x07 |
| #define ADV7182_INPUT_SVIDEO_AIN1_AIN2 0x08 |
| #define ADV7182_INPUT_SVIDEO_AIN3_AIN4 0x09 |
| #define ADV7182_INPUT_SVIDEO_AIN5_AIN6 0x0a |
| #define ADV7182_INPUT_SVIDEO_AIN7_AIN8 0x0b |
| #define ADV7182_INPUT_YPRPB_AIN1_AIN2_AIN3 0x0c |
| #define ADV7182_INPUT_YPRPB_AIN4_AIN5_AIN6 0x0d |
| #define ADV7182_INPUT_DIFF_CVBS_AIN1_AIN2 0x0e |
| #define ADV7182_INPUT_DIFF_CVBS_AIN3_AIN4 0x0f |
| #define ADV7182_INPUT_DIFF_CVBS_AIN5_AIN6 0x10 |
| #define ADV7182_INPUT_DIFF_CVBS_AIN7_AIN8 0x11 |
| |
| #define ADV7180_DEFAULT_CSI_I2C_ADDR 0x44 |
| #define ADV7180_DEFAULT_VPP_I2C_ADDR 0x42 |
| |
| #define V4L2_CID_ADV_FAST_SWITCH (V4L2_CID_USER_ADV7180_BASE + 0x00) |
| |
| /* Initial number of frames to skip to avoid possible garbage */ |
| #define ADV7180_NUM_OF_SKIP_FRAMES 2 |
| |
| struct adv7180_state; |
| |
| #define ADV7180_FLAG_RESET_POWERED BIT(0) |
| #define ADV7180_FLAG_V2 BIT(1) |
| #define ADV7180_FLAG_MIPI_CSI2 BIT(2) |
| #define ADV7180_FLAG_I2P BIT(3) |
| |
| struct adv7180_chip_info { |
| unsigned int flags; |
| unsigned int valid_input_mask; |
| int (*set_std)(struct adv7180_state *st, unsigned int std); |
| int (*select_input)(struct adv7180_state *st, unsigned int input); |
| int (*init)(struct adv7180_state *state); |
| }; |
| |
| struct adv7180_state { |
| struct v4l2_ctrl_handler ctrl_hdl; |
| struct v4l2_subdev sd; |
| struct media_pad pad; |
| struct mutex mutex; /* mutual excl. when accessing chip */ |
| int irq; |
| struct gpio_desc *pwdn_gpio; |
| struct gpio_desc *rst_gpio; |
| v4l2_std_id curr_norm; |
| bool powered; |
| bool streaming; |
| u8 input; |
| |
| struct i2c_client *client; |
| unsigned int register_page; |
| struct i2c_client *csi_client; |
| struct i2c_client *vpp_client; |
| const struct adv7180_chip_info *chip_info; |
| enum v4l2_field field; |
| bool force_bt656_4; |
| }; |
| #define to_adv7180_sd(_ctrl) (&container_of(_ctrl->handler, \ |
| struct adv7180_state, \ |
| ctrl_hdl)->sd) |
| |
| static int adv7180_select_page(struct adv7180_state *state, unsigned int page) |
| { |
| if (state->register_page != page) { |
| i2c_smbus_write_byte_data(state->client, ADV7180_REG_CTRL, |
| page); |
| state->register_page = page; |
| } |
| |
| return 0; |
| } |
| |
| static int adv7180_write(struct adv7180_state *state, unsigned int reg, |
| unsigned int value) |
| { |
| lockdep_assert_held(&state->mutex); |
| adv7180_select_page(state, reg >> 8); |
| return i2c_smbus_write_byte_data(state->client, reg & 0xff, value); |
| } |
| |
| static int adv7180_read(struct adv7180_state *state, unsigned int reg) |
| { |
| lockdep_assert_held(&state->mutex); |
| adv7180_select_page(state, reg >> 8); |
| return i2c_smbus_read_byte_data(state->client, reg & 0xff); |
| } |
| |
| static int adv7180_csi_write(struct adv7180_state *state, unsigned int reg, |
| unsigned int value) |
| { |
| return i2c_smbus_write_byte_data(state->csi_client, reg, value); |
| } |
| |
| static int adv7180_set_video_standard(struct adv7180_state *state, |
| unsigned int std) |
| { |
| return state->chip_info->set_std(state, std); |
| } |
| |
| static int adv7180_vpp_write(struct adv7180_state *state, unsigned int reg, |
| unsigned int value) |
| { |
| return i2c_smbus_write_byte_data(state->vpp_client, reg, value); |
| } |
| |
| static v4l2_std_id adv7180_std_to_v4l2(u8 status1) |
| { |
| /* in case V4L2_IN_ST_NO_SIGNAL */ |
| if (!(status1 & ADV7180_STATUS1_IN_LOCK)) |
| return V4L2_STD_UNKNOWN; |
| |
| switch (status1 & ADV7180_STATUS1_AUTOD_MASK) { |
| case ADV7180_STATUS1_AUTOD_NTSM_M_J: |
| return V4L2_STD_NTSC; |
| case ADV7180_STATUS1_AUTOD_NTSC_4_43: |
| return V4L2_STD_NTSC_443; |
| case ADV7180_STATUS1_AUTOD_PAL_M: |
| return V4L2_STD_PAL_M; |
| case ADV7180_STATUS1_AUTOD_PAL_60: |
| return V4L2_STD_PAL_60; |
| case ADV7180_STATUS1_AUTOD_PAL_B_G: |
| return V4L2_STD_PAL; |
| case ADV7180_STATUS1_AUTOD_SECAM: |
| return V4L2_STD_SECAM; |
| case ADV7180_STATUS1_AUTOD_PAL_COMB: |
| return V4L2_STD_PAL_Nc | V4L2_STD_PAL_N; |
| case ADV7180_STATUS1_AUTOD_SECAM_525: |
| return V4L2_STD_SECAM; |
| default: |
| return V4L2_STD_UNKNOWN; |
| } |
| } |
| |
| static int v4l2_std_to_adv7180(v4l2_std_id std) |
| { |
| if (std == V4L2_STD_PAL_60) |
| return ADV7180_STD_PAL60; |
| if (std == V4L2_STD_NTSC_443) |
| return ADV7180_STD_NTSC_443; |
| if (std == V4L2_STD_PAL_N) |
| return ADV7180_STD_PAL_N; |
| if (std == V4L2_STD_PAL_M) |
| return ADV7180_STD_PAL_M; |
| if (std == V4L2_STD_PAL_Nc) |
| return ADV7180_STD_PAL_COMB_N; |
| |
| if (std & V4L2_STD_PAL) |
| return ADV7180_STD_PAL_BG; |
| if (std & V4L2_STD_NTSC) |
| return ADV7180_STD_NTSC_M; |
| if (std & V4L2_STD_SECAM) |
| return ADV7180_STD_PAL_SECAM; |
| |
| return -EINVAL; |
| } |
| |
| static u32 adv7180_status_to_v4l2(u8 status1) |
| { |
| if (!(status1 & ADV7180_STATUS1_IN_LOCK)) |
| return V4L2_IN_ST_NO_SIGNAL; |
| |
| return 0; |
| } |
| |
| static int __adv7180_status(struct adv7180_state *state, u32 *status, |
| v4l2_std_id *std) |
| { |
| int status1 = adv7180_read(state, ADV7180_REG_STATUS1); |
| |
| if (status1 < 0) |
| return status1; |
| |
| if (status) |
| *status = adv7180_status_to_v4l2(status1); |
| if (std) |
| *std = adv7180_std_to_v4l2(status1); |
| |
| return 0; |
| } |
| |
| static inline struct adv7180_state *to_state(struct v4l2_subdev *sd) |
| { |
| return container_of(sd, struct adv7180_state, sd); |
| } |
| |
| static int adv7180_querystd(struct v4l2_subdev *sd, v4l2_std_id *std) |
| { |
| struct adv7180_state *state = to_state(sd); |
| int err = mutex_lock_interruptible(&state->mutex); |
| if (err) |
| return err; |
| |
| if (state->streaming) { |
| err = -EBUSY; |
| goto unlock; |
| } |
| |
| err = adv7180_set_video_standard(state, |
| ADV7180_STD_AD_PAL_BG_NTSC_J_SECAM); |
| if (err) |
| goto unlock; |
| |
| msleep(100); |
| __adv7180_status(state, NULL, std); |
| |
| err = v4l2_std_to_adv7180(state->curr_norm); |
| if (err < 0) |
| goto unlock; |
| |
| err = adv7180_set_video_standard(state, err); |
| |
| unlock: |
| mutex_unlock(&state->mutex); |
| return err; |
| } |
| |
| static int adv7180_s_routing(struct v4l2_subdev *sd, u32 input, |
| u32 output, u32 config) |
| { |
| struct adv7180_state *state = to_state(sd); |
| int ret = mutex_lock_interruptible(&state->mutex); |
| |
| if (ret) |
| return ret; |
| |
| if (input > 31 || !(BIT(input) & state->chip_info->valid_input_mask)) { |
| ret = -EINVAL; |
| goto out; |
| } |
| |
| ret = state->chip_info->select_input(state, input); |
| |
| if (ret == 0) |
| state->input = input; |
| out: |
| mutex_unlock(&state->mutex); |
| return ret; |
| } |
| |
| static int adv7180_g_input_status(struct v4l2_subdev *sd, u32 *status) |
| { |
| struct adv7180_state *state = to_state(sd); |
| int ret = mutex_lock_interruptible(&state->mutex); |
| if (ret) |
| return ret; |
| |
| ret = __adv7180_status(state, status, NULL); |
| mutex_unlock(&state->mutex); |
| return ret; |
| } |
| |
| static int adv7180_program_std(struct adv7180_state *state) |
| { |
| int ret; |
| |
| ret = v4l2_std_to_adv7180(state->curr_norm); |
| if (ret < 0) |
| return ret; |
| |
| ret = adv7180_set_video_standard(state, ret); |
| if (ret < 0) |
| return ret; |
| return 0; |
| } |
| |
| static int adv7180_s_std(struct v4l2_subdev *sd, v4l2_std_id std) |
| { |
| struct adv7180_state *state = to_state(sd); |
| int ret = mutex_lock_interruptible(&state->mutex); |
| |
| if (ret) |
| return ret; |
| |
| /* Make sure we can support this std */ |
| ret = v4l2_std_to_adv7180(std); |
| if (ret < 0) |
| goto out; |
| |
| state->curr_norm = std; |
| |
| ret = adv7180_program_std(state); |
| out: |
| mutex_unlock(&state->mutex); |
| return ret; |
| } |
| |
| static int adv7180_g_std(struct v4l2_subdev *sd, v4l2_std_id *norm) |
| { |
| struct adv7180_state *state = to_state(sd); |
| |
| *norm = state->curr_norm; |
| |
| return 0; |
| } |
| |
| static int adv7180_g_frame_interval(struct v4l2_subdev *sd, |
| struct v4l2_subdev_frame_interval *fi) |
| { |
| struct adv7180_state *state = to_state(sd); |
| |
| if (state->curr_norm & V4L2_STD_525_60) { |
| fi->interval.numerator = 1001; |
| fi->interval.denominator = 30000; |
| } else { |
| fi->interval.numerator = 1; |
| fi->interval.denominator = 25; |
| } |
| |
| return 0; |
| } |
| |
| static void adv7180_set_power_pin(struct adv7180_state *state, bool on) |
| { |
| if (!state->pwdn_gpio) |
| return; |
| |
| if (on) { |
| gpiod_set_value_cansleep(state->pwdn_gpio, 0); |
| usleep_range(5000, 10000); |
| } else { |
| gpiod_set_value_cansleep(state->pwdn_gpio, 1); |
| } |
| } |
| |
| static void adv7180_set_reset_pin(struct adv7180_state *state, bool on) |
| { |
| if (!state->rst_gpio) |
| return; |
| |
| if (on) { |
| gpiod_set_value_cansleep(state->rst_gpio, 1); |
| } else { |
| gpiod_set_value_cansleep(state->rst_gpio, 0); |
| usleep_range(5000, 10000); |
| } |
| } |
| |
| static int adv7180_set_power(struct adv7180_state *state, bool on) |
| { |
| u8 val; |
| int ret; |
| |
| if (on) |
| val = ADV7180_PWR_MAN_ON; |
| else |
| val = ADV7180_PWR_MAN_OFF; |
| |
| ret = adv7180_write(state, ADV7180_REG_PWR_MAN, val); |
| if (ret) |
| return ret; |
| |
| if (state->chip_info->flags & ADV7180_FLAG_MIPI_CSI2) { |
| if (on) { |
| adv7180_csi_write(state, 0xDE, 0x02); |
| adv7180_csi_write(state, 0xD2, 0xF7); |
| adv7180_csi_write(state, 0xD8, 0x65); |
| adv7180_csi_write(state, 0xE0, 0x09); |
| adv7180_csi_write(state, 0x2C, 0x00); |
| if (state->field == V4L2_FIELD_NONE) |
| adv7180_csi_write(state, 0x1D, 0x80); |
| adv7180_csi_write(state, 0x00, 0x00); |
| } else { |
| adv7180_csi_write(state, 0x00, 0x80); |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int adv7180_s_power(struct v4l2_subdev *sd, int on) |
| { |
| struct adv7180_state *state = to_state(sd); |
| int ret; |
| |
| ret = mutex_lock_interruptible(&state->mutex); |
| if (ret) |
| return ret; |
| |
| ret = adv7180_set_power(state, on); |
| if (ret == 0) |
| state->powered = on; |
| |
| mutex_unlock(&state->mutex); |
| return ret; |
| } |
| |
| static int adv7180_s_ctrl(struct v4l2_ctrl *ctrl) |
| { |
| struct v4l2_subdev *sd = to_adv7180_sd(ctrl); |
| struct adv7180_state *state = to_state(sd); |
| int ret = mutex_lock_interruptible(&state->mutex); |
| int val; |
| |
| if (ret) |
| return ret; |
| val = ctrl->val; |
| switch (ctrl->id) { |
| case V4L2_CID_BRIGHTNESS: |
| ret = adv7180_write(state, ADV7180_REG_BRI, val); |
| break; |
| case V4L2_CID_HUE: |
| /*Hue is inverted according to HSL chart */ |
| ret = adv7180_write(state, ADV7180_REG_HUE, -val); |
| break; |
| case V4L2_CID_CONTRAST: |
| ret = adv7180_write(state, ADV7180_REG_CON, val); |
| break; |
| case V4L2_CID_SATURATION: |
| /* |
| *This could be V4L2_CID_BLUE_BALANCE/V4L2_CID_RED_BALANCE |
| *Let's not confuse the user, everybody understands saturation |
| */ |
| ret = adv7180_write(state, ADV7180_REG_SD_SAT_CB, val); |
| if (ret < 0) |
| break; |
| ret = adv7180_write(state, ADV7180_REG_SD_SAT_CR, val); |
| break; |
| case V4L2_CID_ADV_FAST_SWITCH: |
| if (ctrl->val) { |
| /* ADI required write */ |
| adv7180_write(state, 0x80d9, 0x44); |
| adv7180_write(state, ADV7180_REG_FLCONTROL, |
| ADV7180_FLCONTROL_FL_ENABLE); |
| } else { |
| /* ADI required write */ |
| adv7180_write(state, 0x80d9, 0xc4); |
| adv7180_write(state, ADV7180_REG_FLCONTROL, 0x00); |
| } |
| break; |
| default: |
| ret = -EINVAL; |
| } |
| |
| mutex_unlock(&state->mutex); |
| return ret; |
| } |
| |
| static const struct v4l2_ctrl_ops adv7180_ctrl_ops = { |
| .s_ctrl = adv7180_s_ctrl, |
| }; |
| |
| static const struct v4l2_ctrl_config adv7180_ctrl_fast_switch = { |
| .ops = &adv7180_ctrl_ops, |
| .id = V4L2_CID_ADV_FAST_SWITCH, |
| .name = "Fast Switching", |
| .type = V4L2_CTRL_TYPE_BOOLEAN, |
| .min = 0, |
| .max = 1, |
| .step = 1, |
| }; |
| |
| static int adv7180_init_controls(struct adv7180_state *state) |
| { |
| v4l2_ctrl_handler_init(&state->ctrl_hdl, 4); |
| |
| v4l2_ctrl_new_std(&state->ctrl_hdl, &adv7180_ctrl_ops, |
| V4L2_CID_BRIGHTNESS, ADV7180_BRI_MIN, |
| ADV7180_BRI_MAX, 1, ADV7180_BRI_DEF); |
| v4l2_ctrl_new_std(&state->ctrl_hdl, &adv7180_ctrl_ops, |
| V4L2_CID_CONTRAST, ADV7180_CON_MIN, |
| ADV7180_CON_MAX, 1, ADV7180_CON_DEF); |
| v4l2_ctrl_new_std(&state->ctrl_hdl, &adv7180_ctrl_ops, |
| V4L2_CID_SATURATION, ADV7180_SAT_MIN, |
| ADV7180_SAT_MAX, 1, ADV7180_SAT_DEF); |
| v4l2_ctrl_new_std(&state->ctrl_hdl, &adv7180_ctrl_ops, |
| V4L2_CID_HUE, ADV7180_HUE_MIN, |
| ADV7180_HUE_MAX, 1, ADV7180_HUE_DEF); |
| v4l2_ctrl_new_custom(&state->ctrl_hdl, &adv7180_ctrl_fast_switch, NULL); |
| |
| state->sd.ctrl_handler = &state->ctrl_hdl; |
| if (state->ctrl_hdl.error) { |
| int err = state->ctrl_hdl.error; |
| |
| v4l2_ctrl_handler_free(&state->ctrl_hdl); |
| return err; |
| } |
| v4l2_ctrl_handler_setup(&state->ctrl_hdl); |
| |
| return 0; |
| } |
| static void adv7180_exit_controls(struct adv7180_state *state) |
| { |
| v4l2_ctrl_handler_free(&state->ctrl_hdl); |
| } |
| |
| static int adv7180_enum_mbus_code(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_mbus_code_enum *code) |
| { |
| if (code->index != 0) |
| return -EINVAL; |
| |
| code->code = MEDIA_BUS_FMT_UYVY8_2X8; |
| |
| return 0; |
| } |
| |
| static int adv7180_mbus_fmt(struct v4l2_subdev *sd, |
| struct v4l2_mbus_framefmt *fmt) |
| { |
| struct adv7180_state *state = to_state(sd); |
| |
| fmt->code = MEDIA_BUS_FMT_UYVY8_2X8; |
| fmt->colorspace = V4L2_COLORSPACE_SMPTE170M; |
| fmt->width = 720; |
| fmt->height = state->curr_norm & V4L2_STD_525_60 ? 480 : 576; |
| |
| if (state->field == V4L2_FIELD_ALTERNATE) |
| fmt->height /= 2; |
| |
| return 0; |
| } |
| |
| static int adv7180_set_field_mode(struct adv7180_state *state) |
| { |
| if (!(state->chip_info->flags & ADV7180_FLAG_I2P)) |
| return 0; |
| |
| if (state->field == V4L2_FIELD_NONE) { |
| if (state->chip_info->flags & ADV7180_FLAG_MIPI_CSI2) { |
| adv7180_csi_write(state, 0x01, 0x20); |
| adv7180_csi_write(state, 0x02, 0x28); |
| adv7180_csi_write(state, 0x03, 0x38); |
| adv7180_csi_write(state, 0x04, 0x30); |
| adv7180_csi_write(state, 0x05, 0x30); |
| adv7180_csi_write(state, 0x06, 0x80); |
| adv7180_csi_write(state, 0x07, 0x70); |
| adv7180_csi_write(state, 0x08, 0x50); |
| } |
| adv7180_vpp_write(state, 0xa3, 0x00); |
| adv7180_vpp_write(state, 0x5b, 0x00); |
| adv7180_vpp_write(state, 0x55, 0x80); |
| } else { |
| if (state->chip_info->flags & ADV7180_FLAG_MIPI_CSI2) { |
| adv7180_csi_write(state, 0x01, 0x18); |
| adv7180_csi_write(state, 0x02, 0x18); |
| adv7180_csi_write(state, 0x03, 0x30); |
| adv7180_csi_write(state, 0x04, 0x20); |
| adv7180_csi_write(state, 0x05, 0x28); |
| adv7180_csi_write(state, 0x06, 0x40); |
| adv7180_csi_write(state, 0x07, 0x58); |
| adv7180_csi_write(state, 0x08, 0x30); |
| } |
| adv7180_vpp_write(state, 0xa3, 0x70); |
| adv7180_vpp_write(state, 0x5b, 0x80); |
| adv7180_vpp_write(state, 0x55, 0x00); |
| } |
| |
| return 0; |
| } |
| |
| static int adv7180_get_pad_format(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_format *format) |
| { |
| struct adv7180_state *state = to_state(sd); |
| |
| if (format->which == V4L2_SUBDEV_FORMAT_TRY) { |
| format->format = *v4l2_subdev_get_try_format(sd, sd_state, 0); |
| } else { |
| adv7180_mbus_fmt(sd, &format->format); |
| format->format.field = state->field; |
| } |
| |
| return 0; |
| } |
| |
| static int adv7180_set_pad_format(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_format *format) |
| { |
| struct adv7180_state *state = to_state(sd); |
| struct v4l2_mbus_framefmt *framefmt; |
| int ret; |
| |
| switch (format->format.field) { |
| case V4L2_FIELD_NONE: |
| if (state->chip_info->flags & ADV7180_FLAG_I2P) |
| break; |
| fallthrough; |
| default: |
| format->format.field = V4L2_FIELD_ALTERNATE; |
| break; |
| } |
| |
| ret = adv7180_mbus_fmt(sd, &format->format); |
| |
| if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE) { |
| if (state->field != format->format.field) { |
| state->field = format->format.field; |
| adv7180_set_power(state, false); |
| adv7180_set_field_mode(state); |
| adv7180_set_power(state, true); |
| } |
| } else { |
| framefmt = v4l2_subdev_get_try_format(sd, sd_state, 0); |
| *framefmt = format->format; |
| } |
| |
| return ret; |
| } |
| |
| static int adv7180_init_cfg(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state) |
| { |
| struct v4l2_subdev_format fmt = { |
| .which = sd_state ? V4L2_SUBDEV_FORMAT_TRY |
| : V4L2_SUBDEV_FORMAT_ACTIVE, |
| }; |
| |
| return adv7180_set_pad_format(sd, sd_state, &fmt); |
| } |
| |
| static int adv7180_get_mbus_config(struct v4l2_subdev *sd, |
| unsigned int pad, |
| struct v4l2_mbus_config *cfg) |
| { |
| struct adv7180_state *state = to_state(sd); |
| |
| if (state->chip_info->flags & ADV7180_FLAG_MIPI_CSI2) { |
| cfg->type = V4L2_MBUS_CSI2_DPHY; |
| cfg->bus.mipi_csi2.num_data_lanes = 1; |
| cfg->bus.mipi_csi2.flags = 0; |
| } else { |
| /* |
| * The ADV7180 sensor supports BT.601/656 output modes. |
| * The BT.656 is default and not yet configurable by s/w. |
| */ |
| cfg->bus.parallel.flags = V4L2_MBUS_MASTER | |
| V4L2_MBUS_PCLK_SAMPLE_RISING | |
| V4L2_MBUS_DATA_ACTIVE_HIGH; |
| cfg->type = V4L2_MBUS_BT656; |
| } |
| |
| return 0; |
| } |
| |
| static int adv7180_get_skip_frames(struct v4l2_subdev *sd, u32 *frames) |
| { |
| *frames = ADV7180_NUM_OF_SKIP_FRAMES; |
| |
| return 0; |
| } |
| |
| static int adv7180_g_pixelaspect(struct v4l2_subdev *sd, struct v4l2_fract *aspect) |
| { |
| struct adv7180_state *state = to_state(sd); |
| |
| if (state->curr_norm & V4L2_STD_525_60) { |
| aspect->numerator = 11; |
| aspect->denominator = 10; |
| } else { |
| aspect->numerator = 54; |
| aspect->denominator = 59; |
| } |
| |
| return 0; |
| } |
| |
| static int adv7180_g_tvnorms(struct v4l2_subdev *sd, v4l2_std_id *norm) |
| { |
| *norm = V4L2_STD_ALL; |
| return 0; |
| } |
| |
| static int adv7180_s_stream(struct v4l2_subdev *sd, int enable) |
| { |
| struct adv7180_state *state = to_state(sd); |
| int ret; |
| |
| /* It's always safe to stop streaming, no need to take the lock */ |
| if (!enable) { |
| state->streaming = enable; |
| return 0; |
| } |
| |
| /* Must wait until querystd released the lock */ |
| ret = mutex_lock_interruptible(&state->mutex); |
| if (ret) |
| return ret; |
| state->streaming = enable; |
| mutex_unlock(&state->mutex); |
| return 0; |
| } |
| |
| static int adv7180_subscribe_event(struct v4l2_subdev *sd, |
| struct v4l2_fh *fh, |
| struct v4l2_event_subscription *sub) |
| { |
| switch (sub->type) { |
| case V4L2_EVENT_SOURCE_CHANGE: |
| return v4l2_src_change_event_subdev_subscribe(sd, fh, sub); |
| case V4L2_EVENT_CTRL: |
| return v4l2_ctrl_subdev_subscribe_event(sd, fh, sub); |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static const struct v4l2_subdev_video_ops adv7180_video_ops = { |
| .s_std = adv7180_s_std, |
| .g_std = adv7180_g_std, |
| .g_frame_interval = adv7180_g_frame_interval, |
| .querystd = adv7180_querystd, |
| .g_input_status = adv7180_g_input_status, |
| .s_routing = adv7180_s_routing, |
| .g_pixelaspect = adv7180_g_pixelaspect, |
| .g_tvnorms = adv7180_g_tvnorms, |
| .s_stream = adv7180_s_stream, |
| }; |
| |
| static const struct v4l2_subdev_core_ops adv7180_core_ops = { |
| .s_power = adv7180_s_power, |
| .subscribe_event = adv7180_subscribe_event, |
| .unsubscribe_event = v4l2_event_subdev_unsubscribe, |
| }; |
| |
| static const struct v4l2_subdev_pad_ops adv7180_pad_ops = { |
| .init_cfg = adv7180_init_cfg, |
| .enum_mbus_code = adv7180_enum_mbus_code, |
| .set_fmt = adv7180_set_pad_format, |
| .get_fmt = adv7180_get_pad_format, |
| .get_mbus_config = adv7180_get_mbus_config, |
| }; |
| |
| static const struct v4l2_subdev_sensor_ops adv7180_sensor_ops = { |
| .g_skip_frames = adv7180_get_skip_frames, |
| }; |
| |
| static const struct v4l2_subdev_ops adv7180_ops = { |
| .core = &adv7180_core_ops, |
| .video = &adv7180_video_ops, |
| .pad = &adv7180_pad_ops, |
| .sensor = &adv7180_sensor_ops, |
| }; |
| |
| static irqreturn_t adv7180_irq(int irq, void *devid) |
| { |
| struct adv7180_state *state = devid; |
| u8 isr3; |
| |
| mutex_lock(&state->mutex); |
| isr3 = adv7180_read(state, ADV7180_REG_ISR3); |
| /* clear */ |
| adv7180_write(state, ADV7180_REG_ICR3, isr3); |
| |
| if (isr3 & ADV7180_IRQ3_AD_CHANGE) { |
| static const struct v4l2_event src_ch = { |
| .type = V4L2_EVENT_SOURCE_CHANGE, |
| .u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION, |
| }; |
| |
| v4l2_subdev_notify_event(&state->sd, &src_ch); |
| } |
| mutex_unlock(&state->mutex); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int adv7180_init(struct adv7180_state *state) |
| { |
| int ret; |
| |
| /* ITU-R BT.656-4 compatible */ |
| ret = adv7180_write(state, ADV7180_REG_EXTENDED_OUTPUT_CONTROL, |
| ADV7180_EXTENDED_OUTPUT_CONTROL_NTSCDIS); |
| if (ret < 0) |
| return ret; |
| |
| /* Manually set V bit end position in NTSC mode */ |
| return adv7180_write(state, ADV7180_REG_NTSC_V_BIT_END, |
| ADV7180_NTSC_V_BIT_END_MANUAL_NVEND); |
| } |
| |
| static int adv7180_set_std(struct adv7180_state *state, unsigned int std) |
| { |
| return adv7180_write(state, ADV7180_REG_INPUT_CONTROL, |
| (std << 4) | state->input); |
| } |
| |
| static int adv7180_select_input(struct adv7180_state *state, unsigned int input) |
| { |
| int ret; |
| |
| ret = adv7180_read(state, ADV7180_REG_INPUT_CONTROL); |
| if (ret < 0) |
| return ret; |
| |
| ret &= ~ADV7180_INPUT_CONTROL_INSEL_MASK; |
| ret |= input; |
| return adv7180_write(state, ADV7180_REG_INPUT_CONTROL, ret); |
| } |
| |
| static int adv7182_init(struct adv7180_state *state) |
| { |
| if (state->chip_info->flags & ADV7180_FLAG_MIPI_CSI2) |
| adv7180_write(state, ADV7180_REG_CSI_SLAVE_ADDR, |
| ADV7180_DEFAULT_CSI_I2C_ADDR << 1); |
| |
| if (state->chip_info->flags & ADV7180_FLAG_I2P) |
| adv7180_write(state, ADV7180_REG_VPP_SLAVE_ADDR, |
| ADV7180_DEFAULT_VPP_I2C_ADDR << 1); |
| |
| if (state->chip_info->flags & ADV7180_FLAG_V2) { |
| /* ADI recommended writes for improved video quality */ |
| adv7180_write(state, 0x0080, 0x51); |
| adv7180_write(state, 0x0081, 0x51); |
| adv7180_write(state, 0x0082, 0x68); |
| } |
| |
| /* ADI required writes */ |
| if (state->chip_info->flags & ADV7180_FLAG_MIPI_CSI2) { |
| adv7180_write(state, ADV7180_REG_OUTPUT_CONTROL, 0x4e); |
| adv7180_write(state, ADV7180_REG_EXTENDED_OUTPUT_CONTROL, 0x57); |
| adv7180_write(state, ADV7180_REG_CTRL_2, 0xc0); |
| } else { |
| if (state->chip_info->flags & ADV7180_FLAG_V2) { |
| if (state->force_bt656_4) { |
| /* ITU-R BT.656-4 compatible */ |
| adv7180_write(state, |
| ADV7180_REG_EXTENDED_OUTPUT_CONTROL, |
| ADV7180_EXTENDED_OUTPUT_CONTROL_NTSCDIS); |
| /* Manually set NEWAVMODE */ |
| adv7180_write(state, |
| ADV7180_REG_VSYNC_FIELD_CTL_1, |
| ADV7180_VSYNC_FIELD_CTL_1_NEWAV); |
| /* Manually set V bit end position in NTSC mode */ |
| adv7180_write(state, |
| ADV7180_REG_NTSC_V_BIT_END, |
| ADV7180_NTSC_V_BIT_END_MANUAL_NVEND); |
| } else { |
| adv7180_write(state, |
| ADV7180_REG_EXTENDED_OUTPUT_CONTROL, |
| 0x17); |
| } |
| } |
| else |
| adv7180_write(state, |
| ADV7180_REG_EXTENDED_OUTPUT_CONTROL, |
| 0x07); |
| adv7180_write(state, ADV7180_REG_OUTPUT_CONTROL, 0x0c); |
| adv7180_write(state, ADV7180_REG_CTRL_2, 0x40); |
| } |
| |
| adv7180_write(state, 0x0013, 0x00); |
| |
| return 0; |
| } |
| |
| static int adv7182_set_std(struct adv7180_state *state, unsigned int std) |
| { |
| return adv7180_write(state, ADV7182_REG_INPUT_VIDSEL, std << 4); |
| } |
| |
| enum adv7182_input_type { |
| ADV7182_INPUT_TYPE_CVBS, |
| ADV7182_INPUT_TYPE_DIFF_CVBS, |
| ADV7182_INPUT_TYPE_SVIDEO, |
| ADV7182_INPUT_TYPE_YPBPR, |
| }; |
| |
| static enum adv7182_input_type adv7182_get_input_type(unsigned int input) |
| { |
| switch (input) { |
| case ADV7182_INPUT_CVBS_AIN1: |
| case ADV7182_INPUT_CVBS_AIN2: |
| case ADV7182_INPUT_CVBS_AIN3: |
| case ADV7182_INPUT_CVBS_AIN4: |
| case ADV7182_INPUT_CVBS_AIN5: |
| case ADV7182_INPUT_CVBS_AIN6: |
| case ADV7182_INPUT_CVBS_AIN7: |
| case ADV7182_INPUT_CVBS_AIN8: |
| return ADV7182_INPUT_TYPE_CVBS; |
| case ADV7182_INPUT_SVIDEO_AIN1_AIN2: |
| case ADV7182_INPUT_SVIDEO_AIN3_AIN4: |
| case ADV7182_INPUT_SVIDEO_AIN5_AIN6: |
| case ADV7182_INPUT_SVIDEO_AIN7_AIN8: |
| return ADV7182_INPUT_TYPE_SVIDEO; |
| case ADV7182_INPUT_YPRPB_AIN1_AIN2_AIN3: |
| case ADV7182_INPUT_YPRPB_AIN4_AIN5_AIN6: |
| return ADV7182_INPUT_TYPE_YPBPR; |
| case ADV7182_INPUT_DIFF_CVBS_AIN1_AIN2: |
| case ADV7182_INPUT_DIFF_CVBS_AIN3_AIN4: |
| case ADV7182_INPUT_DIFF_CVBS_AIN5_AIN6: |
| case ADV7182_INPUT_DIFF_CVBS_AIN7_AIN8: |
| return ADV7182_INPUT_TYPE_DIFF_CVBS; |
| default: /* Will never happen */ |
| return 0; |
| } |
| } |
| |
| /* ADI recommended writes to registers 0x52, 0x53, 0x54 */ |
| static unsigned int adv7182_lbias_settings[][3] = { |
| [ADV7182_INPUT_TYPE_CVBS] = { 0xCB, 0x4E, 0x80 }, |
| [ADV7182_INPUT_TYPE_DIFF_CVBS] = { 0xC0, 0x4E, 0x80 }, |
| [ADV7182_INPUT_TYPE_SVIDEO] = { 0x0B, 0xCE, 0x80 }, |
| [ADV7182_INPUT_TYPE_YPBPR] = { 0x0B, 0x4E, 0xC0 }, |
| }; |
| |
| static unsigned int adv7280_lbias_settings[][3] = { |
| [ADV7182_INPUT_TYPE_CVBS] = { 0xCD, 0x4E, 0x80 }, |
| [ADV7182_INPUT_TYPE_DIFF_CVBS] = { 0xC0, 0x4E, 0x80 }, |
| [ADV7182_INPUT_TYPE_SVIDEO] = { 0x0B, 0xCE, 0x80 }, |
| [ADV7182_INPUT_TYPE_YPBPR] = { 0x0B, 0x4E, 0xC0 }, |
| }; |
| |
| static int adv7182_select_input(struct adv7180_state *state, unsigned int input) |
| { |
| enum adv7182_input_type input_type; |
| unsigned int *lbias; |
| unsigned int i; |
| int ret; |
| |
| ret = adv7180_write(state, ADV7180_REG_INPUT_CONTROL, input); |
| if (ret) |
| return ret; |
| |
| /* Reset clamp circuitry - ADI recommended writes */ |
| adv7180_write(state, ADV7180_REG_RST_CLAMP, 0x00); |
| adv7180_write(state, ADV7180_REG_RST_CLAMP, 0xff); |
| |
| input_type = adv7182_get_input_type(input); |
| |
| switch (input_type) { |
| case ADV7182_INPUT_TYPE_CVBS: |
| case ADV7182_INPUT_TYPE_DIFF_CVBS: |
| /* ADI recommends to use the SH1 filter */ |
| adv7180_write(state, ADV7180_REG_SHAP_FILTER_CTL_1, 0x41); |
| break; |
| default: |
| adv7180_write(state, ADV7180_REG_SHAP_FILTER_CTL_1, 0x01); |
| break; |
| } |
| |
| if (state->chip_info->flags & ADV7180_FLAG_V2) |
| lbias = adv7280_lbias_settings[input_type]; |
| else |
| lbias = adv7182_lbias_settings[input_type]; |
| |
| for (i = 0; i < ARRAY_SIZE(adv7182_lbias_settings[0]); i++) |
| adv7180_write(state, ADV7180_REG_CVBS_TRIM + i, lbias[i]); |
| |
| if (input_type == ADV7182_INPUT_TYPE_DIFF_CVBS) { |
| /* ADI required writes to make differential CVBS work */ |
| adv7180_write(state, ADV7180_REG_RES_CIR, 0xa8); |
| adv7180_write(state, ADV7180_REG_CLAMP_ADJ, 0x90); |
| adv7180_write(state, ADV7180_REG_DIFF_MODE, 0xb0); |
| adv7180_write(state, ADV7180_REG_AGC_ADJ1, 0x08); |
| adv7180_write(state, ADV7180_REG_AGC_ADJ2, 0xa0); |
| } else { |
| adv7180_write(state, ADV7180_REG_RES_CIR, 0xf0); |
| adv7180_write(state, ADV7180_REG_CLAMP_ADJ, 0xd0); |
| adv7180_write(state, ADV7180_REG_DIFF_MODE, 0x10); |
| adv7180_write(state, ADV7180_REG_AGC_ADJ1, 0x9c); |
| adv7180_write(state, ADV7180_REG_AGC_ADJ2, 0x00); |
| } |
| |
| return 0; |
| } |
| |
| static const struct adv7180_chip_info adv7180_info = { |
| .flags = ADV7180_FLAG_RESET_POWERED, |
| /* We cannot discriminate between LQFP and 40-pin LFCSP, so accept |
| * all inputs and let the card driver take care of validation |
| */ |
| .valid_input_mask = BIT(ADV7180_INPUT_CVBS_AIN1) | |
| BIT(ADV7180_INPUT_CVBS_AIN2) | |
| BIT(ADV7180_INPUT_CVBS_AIN3) | |
| BIT(ADV7180_INPUT_CVBS_AIN4) | |
| BIT(ADV7180_INPUT_CVBS_AIN5) | |
| BIT(ADV7180_INPUT_CVBS_AIN6) | |
| BIT(ADV7180_INPUT_SVIDEO_AIN1_AIN2) | |
| BIT(ADV7180_INPUT_SVIDEO_AIN3_AIN4) | |
| BIT(ADV7180_INPUT_SVIDEO_AIN5_AIN6) | |
| BIT(ADV7180_INPUT_YPRPB_AIN1_AIN2_AIN3) | |
| BIT(ADV7180_INPUT_YPRPB_AIN4_AIN5_AIN6), |
| .init = adv7180_init, |
| .set_std = adv7180_set_std, |
| .select_input = adv7180_select_input, |
| }; |
| |
| static const struct adv7180_chip_info adv7182_info = { |
| .valid_input_mask = BIT(ADV7182_INPUT_CVBS_AIN1) | |
| BIT(ADV7182_INPUT_CVBS_AIN2) | |
| BIT(ADV7182_INPUT_CVBS_AIN3) | |
| BIT(ADV7182_INPUT_CVBS_AIN4) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN3_AIN4) | |
| BIT(ADV7182_INPUT_YPRPB_AIN1_AIN2_AIN3) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN3_AIN4), |
| .init = adv7182_init, |
| .set_std = adv7182_set_std, |
| .select_input = adv7182_select_input, |
| }; |
| |
| static const struct adv7180_chip_info adv7280_info = { |
| .flags = ADV7180_FLAG_V2 | ADV7180_FLAG_I2P, |
| .valid_input_mask = BIT(ADV7182_INPUT_CVBS_AIN1) | |
| BIT(ADV7182_INPUT_CVBS_AIN2) | |
| BIT(ADV7182_INPUT_CVBS_AIN3) | |
| BIT(ADV7182_INPUT_CVBS_AIN4) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN3_AIN4) | |
| BIT(ADV7182_INPUT_YPRPB_AIN1_AIN2_AIN3), |
| .init = adv7182_init, |
| .set_std = adv7182_set_std, |
| .select_input = adv7182_select_input, |
| }; |
| |
| static const struct adv7180_chip_info adv7280_m_info = { |
| .flags = ADV7180_FLAG_V2 | ADV7180_FLAG_MIPI_CSI2 | ADV7180_FLAG_I2P, |
| .valid_input_mask = BIT(ADV7182_INPUT_CVBS_AIN1) | |
| BIT(ADV7182_INPUT_CVBS_AIN2) | |
| BIT(ADV7182_INPUT_CVBS_AIN3) | |
| BIT(ADV7182_INPUT_CVBS_AIN4) | |
| BIT(ADV7182_INPUT_CVBS_AIN5) | |
| BIT(ADV7182_INPUT_CVBS_AIN6) | |
| BIT(ADV7182_INPUT_CVBS_AIN7) | |
| BIT(ADV7182_INPUT_CVBS_AIN8) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN3_AIN4) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN5_AIN6) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN7_AIN8) | |
| BIT(ADV7182_INPUT_YPRPB_AIN1_AIN2_AIN3) | |
| BIT(ADV7182_INPUT_YPRPB_AIN4_AIN5_AIN6), |
| .init = adv7182_init, |
| .set_std = adv7182_set_std, |
| .select_input = adv7182_select_input, |
| }; |
| |
| static const struct adv7180_chip_info adv7281_info = { |
| .flags = ADV7180_FLAG_V2 | ADV7180_FLAG_MIPI_CSI2, |
| .valid_input_mask = BIT(ADV7182_INPUT_CVBS_AIN1) | |
| BIT(ADV7182_INPUT_CVBS_AIN2) | |
| BIT(ADV7182_INPUT_CVBS_AIN7) | |
| BIT(ADV7182_INPUT_CVBS_AIN8) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN7_AIN8) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN7_AIN8), |
| .init = adv7182_init, |
| .set_std = adv7182_set_std, |
| .select_input = adv7182_select_input, |
| }; |
| |
| static const struct adv7180_chip_info adv7281_m_info = { |
| .flags = ADV7180_FLAG_V2 | ADV7180_FLAG_MIPI_CSI2, |
| .valid_input_mask = BIT(ADV7182_INPUT_CVBS_AIN1) | |
| BIT(ADV7182_INPUT_CVBS_AIN2) | |
| BIT(ADV7182_INPUT_CVBS_AIN3) | |
| BIT(ADV7182_INPUT_CVBS_AIN4) | |
| BIT(ADV7182_INPUT_CVBS_AIN7) | |
| BIT(ADV7182_INPUT_CVBS_AIN8) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN3_AIN4) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN7_AIN8) | |
| BIT(ADV7182_INPUT_YPRPB_AIN1_AIN2_AIN3) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN3_AIN4) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN7_AIN8), |
| .init = adv7182_init, |
| .set_std = adv7182_set_std, |
| .select_input = adv7182_select_input, |
| }; |
| |
| static const struct adv7180_chip_info adv7281_ma_info = { |
| .flags = ADV7180_FLAG_V2 | ADV7180_FLAG_MIPI_CSI2, |
| .valid_input_mask = BIT(ADV7182_INPUT_CVBS_AIN1) | |
| BIT(ADV7182_INPUT_CVBS_AIN2) | |
| BIT(ADV7182_INPUT_CVBS_AIN3) | |
| BIT(ADV7182_INPUT_CVBS_AIN4) | |
| BIT(ADV7182_INPUT_CVBS_AIN5) | |
| BIT(ADV7182_INPUT_CVBS_AIN6) | |
| BIT(ADV7182_INPUT_CVBS_AIN7) | |
| BIT(ADV7182_INPUT_CVBS_AIN8) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN3_AIN4) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN5_AIN6) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN7_AIN8) | |
| BIT(ADV7182_INPUT_YPRPB_AIN1_AIN2_AIN3) | |
| BIT(ADV7182_INPUT_YPRPB_AIN4_AIN5_AIN6) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN3_AIN4) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN5_AIN6) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN7_AIN8), |
| .init = adv7182_init, |
| .set_std = adv7182_set_std, |
| .select_input = adv7182_select_input, |
| }; |
| |
| static const struct adv7180_chip_info adv7282_info = { |
| .flags = ADV7180_FLAG_V2 | ADV7180_FLAG_I2P, |
| .valid_input_mask = BIT(ADV7182_INPUT_CVBS_AIN1) | |
| BIT(ADV7182_INPUT_CVBS_AIN2) | |
| BIT(ADV7182_INPUT_CVBS_AIN7) | |
| BIT(ADV7182_INPUT_CVBS_AIN8) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN7_AIN8) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN7_AIN8), |
| .init = adv7182_init, |
| .set_std = adv7182_set_std, |
| .select_input = adv7182_select_input, |
| }; |
| |
| static const struct adv7180_chip_info adv7282_m_info = { |
| .flags = ADV7180_FLAG_V2 | ADV7180_FLAG_MIPI_CSI2 | ADV7180_FLAG_I2P, |
| .valid_input_mask = BIT(ADV7182_INPUT_CVBS_AIN1) | |
| BIT(ADV7182_INPUT_CVBS_AIN2) | |
| BIT(ADV7182_INPUT_CVBS_AIN3) | |
| BIT(ADV7182_INPUT_CVBS_AIN4) | |
| BIT(ADV7182_INPUT_CVBS_AIN7) | |
| BIT(ADV7182_INPUT_CVBS_AIN8) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN3_AIN4) | |
| BIT(ADV7182_INPUT_SVIDEO_AIN7_AIN8) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN1_AIN2) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN3_AIN4) | |
| BIT(ADV7182_INPUT_DIFF_CVBS_AIN7_AIN8), |
| .init = adv7182_init, |
| .set_std = adv7182_set_std, |
| .select_input = adv7182_select_input, |
| }; |
| |
| static int init_device(struct adv7180_state *state) |
| { |
| int ret; |
| |
| mutex_lock(&state->mutex); |
| |
| adv7180_set_power_pin(state, true); |
| adv7180_set_reset_pin(state, false); |
| |
| adv7180_write(state, ADV7180_REG_PWR_MAN, ADV7180_PWR_MAN_RES); |
| usleep_range(5000, 10000); |
| |
| ret = state->chip_info->init(state); |
| if (ret) |
| goto out_unlock; |
| |
| ret = adv7180_program_std(state); |
| if (ret) |
| goto out_unlock; |
| |
| adv7180_set_field_mode(state); |
| |
| /* register for interrupts */ |
| if (state->irq > 0) { |
| /* config the Interrupt pin to be active low */ |
| ret = adv7180_write(state, ADV7180_REG_ICONF1, |
| ADV7180_ICONF1_ACTIVE_LOW | |
| ADV7180_ICONF1_PSYNC_ONLY); |
| if (ret < 0) |
| goto out_unlock; |
| |
| ret = adv7180_write(state, ADV7180_REG_IMR1, 0); |
| if (ret < 0) |
| goto out_unlock; |
| |
| ret = adv7180_write(state, ADV7180_REG_IMR2, 0); |
| if (ret < 0) |
| goto out_unlock; |
| |
| /* enable AD change interrupts interrupts */ |
| ret = adv7180_write(state, ADV7180_REG_IMR3, |
| ADV7180_IRQ3_AD_CHANGE); |
| if (ret < 0) |
| goto out_unlock; |
| |
| ret = adv7180_write(state, ADV7180_REG_IMR4, 0); |
| if (ret < 0) |
| goto out_unlock; |
| } |
| |
| out_unlock: |
| mutex_unlock(&state->mutex); |
| |
| return ret; |
| } |
| |
| static int adv7180_probe(struct i2c_client *client, |
| const struct i2c_device_id *id) |
| { |
| struct device_node *np = client->dev.of_node; |
| struct adv7180_state *state; |
| struct v4l2_subdev *sd; |
| int ret; |
| |
| /* Check if the adapter supports the needed features */ |
| if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) |
| return -EIO; |
| |
| state = devm_kzalloc(&client->dev, sizeof(*state), GFP_KERNEL); |
| if (state == NULL) |
| return -ENOMEM; |
| |
| state->client = client; |
| state->field = V4L2_FIELD_ALTERNATE; |
| state->chip_info = (struct adv7180_chip_info *)id->driver_data; |
| |
| state->pwdn_gpio = devm_gpiod_get_optional(&client->dev, "powerdown", |
| GPIOD_OUT_HIGH); |
| if (IS_ERR(state->pwdn_gpio)) { |
| ret = PTR_ERR(state->pwdn_gpio); |
| v4l_err(client, "request for power pin failed: %d\n", ret); |
| return ret; |
| } |
| |
| state->rst_gpio = devm_gpiod_get_optional(&client->dev, "reset", |
| GPIOD_OUT_HIGH); |
| if (IS_ERR(state->rst_gpio)) { |
| ret = PTR_ERR(state->rst_gpio); |
| v4l_err(client, "request for reset pin failed: %d\n", ret); |
| return ret; |
| } |
| |
| if (of_property_read_bool(np, "adv,force-bt656-4")) |
| state->force_bt656_4 = true; |
| |
| if (state->chip_info->flags & ADV7180_FLAG_MIPI_CSI2) { |
| state->csi_client = i2c_new_dummy_device(client->adapter, |
| ADV7180_DEFAULT_CSI_I2C_ADDR); |
| if (IS_ERR(state->csi_client)) |
| return PTR_ERR(state->csi_client); |
| } |
| |
| if (state->chip_info->flags & ADV7180_FLAG_I2P) { |
| state->vpp_client = i2c_new_dummy_device(client->adapter, |
| ADV7180_DEFAULT_VPP_I2C_ADDR); |
| if (IS_ERR(state->vpp_client)) { |
| ret = PTR_ERR(state->vpp_client); |
| goto err_unregister_csi_client; |
| } |
| } |
| |
| state->irq = client->irq; |
| mutex_init(&state->mutex); |
| state->curr_norm = V4L2_STD_NTSC; |
| if (state->chip_info->flags & ADV7180_FLAG_RESET_POWERED) |
| state->powered = true; |
| else |
| state->powered = false; |
| state->input = 0; |
| sd = &state->sd; |
| v4l2_i2c_subdev_init(sd, client, &adv7180_ops); |
| sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS; |
| |
| ret = adv7180_init_controls(state); |
| if (ret) |
| goto err_unregister_vpp_client; |
| |
| state->pad.flags = MEDIA_PAD_FL_SOURCE; |
| sd->entity.function = MEDIA_ENT_F_ATV_DECODER; |
| ret = media_entity_pads_init(&sd->entity, 1, &state->pad); |
| if (ret) |
| goto err_free_ctrl; |
| |
| ret = init_device(state); |
| if (ret) |
| goto err_media_entity_cleanup; |
| |
| if (state->irq) { |
| ret = request_threaded_irq(client->irq, NULL, adv7180_irq, |
| IRQF_ONESHOT | IRQF_TRIGGER_FALLING, |
| KBUILD_MODNAME, state); |
| if (ret) |
| goto err_media_entity_cleanup; |
| } |
| |
| ret = v4l2_async_register_subdev(sd); |
| if (ret) |
| goto err_free_irq; |
| |
| mutex_lock(&state->mutex); |
| ret = adv7180_read(state, ADV7180_REG_IDENT); |
| mutex_unlock(&state->mutex); |
| if (ret < 0) |
| goto err_v4l2_async_unregister; |
| |
| v4l_info(client, "chip id 0x%x found @ 0x%02x (%s)\n", |
| ret, client->addr, client->adapter->name); |
| |
| return 0; |
| |
| err_v4l2_async_unregister: |
| v4l2_async_unregister_subdev(sd); |
| err_free_irq: |
| if (state->irq > 0) |
| free_irq(client->irq, state); |
| err_media_entity_cleanup: |
| media_entity_cleanup(&sd->entity); |
| err_free_ctrl: |
| adv7180_exit_controls(state); |
| err_unregister_vpp_client: |
| i2c_unregister_device(state->vpp_client); |
| err_unregister_csi_client: |
| i2c_unregister_device(state->csi_client); |
| mutex_destroy(&state->mutex); |
| return ret; |
| } |
| |
| static int adv7180_remove(struct i2c_client *client) |
| { |
| struct v4l2_subdev *sd = i2c_get_clientdata(client); |
| struct adv7180_state *state = to_state(sd); |
| |
| v4l2_async_unregister_subdev(sd); |
| |
| if (state->irq > 0) |
| free_irq(client->irq, state); |
| |
| media_entity_cleanup(&sd->entity); |
| adv7180_exit_controls(state); |
| |
| i2c_unregister_device(state->vpp_client); |
| i2c_unregister_device(state->csi_client); |
| |
| adv7180_set_reset_pin(state, true); |
| adv7180_set_power_pin(state, false); |
| |
| mutex_destroy(&state->mutex); |
| |
| return 0; |
| } |
| |
| static const struct i2c_device_id adv7180_id[] = { |
| { "adv7180", (kernel_ulong_t)&adv7180_info }, |
| { "adv7180cp", (kernel_ulong_t)&adv7180_info }, |
| { "adv7180st", (kernel_ulong_t)&adv7180_info }, |
| { "adv7182", (kernel_ulong_t)&adv7182_info }, |
| { "adv7280", (kernel_ulong_t)&adv7280_info }, |
| { "adv7280-m", (kernel_ulong_t)&adv7280_m_info }, |
| { "adv7281", (kernel_ulong_t)&adv7281_info }, |
| { "adv7281-m", (kernel_ulong_t)&adv7281_m_info }, |
| { "adv7281-ma", (kernel_ulong_t)&adv7281_ma_info }, |
| { "adv7282", (kernel_ulong_t)&adv7282_info }, |
| { "adv7282-m", (kernel_ulong_t)&adv7282_m_info }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(i2c, adv7180_id); |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int adv7180_suspend(struct device *dev) |
| { |
| struct v4l2_subdev *sd = dev_get_drvdata(dev); |
| struct adv7180_state *state = to_state(sd); |
| |
| return adv7180_set_power(state, false); |
| } |
| |
| static int adv7180_resume(struct device *dev) |
| { |
| struct v4l2_subdev *sd = dev_get_drvdata(dev); |
| struct adv7180_state *state = to_state(sd); |
| int ret; |
| |
| ret = init_device(state); |
| if (ret < 0) |
| return ret; |
| |
| ret = adv7180_set_power(state, state->powered); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static SIMPLE_DEV_PM_OPS(adv7180_pm_ops, adv7180_suspend, adv7180_resume); |
| #define ADV7180_PM_OPS (&adv7180_pm_ops) |
| |
| #else |
| #define ADV7180_PM_OPS NULL |
| #endif |
| |
| #ifdef CONFIG_OF |
| static const struct of_device_id adv7180_of_id[] = { |
| { .compatible = "adi,adv7180", }, |
| { .compatible = "adi,adv7180cp", }, |
| { .compatible = "adi,adv7180st", }, |
| { .compatible = "adi,adv7182", }, |
| { .compatible = "adi,adv7280", }, |
| { .compatible = "adi,adv7280-m", }, |
| { .compatible = "adi,adv7281", }, |
| { .compatible = "adi,adv7281-m", }, |
| { .compatible = "adi,adv7281-ma", }, |
| { .compatible = "adi,adv7282", }, |
| { .compatible = "adi,adv7282-m", }, |
| { }, |
| }; |
| |
| MODULE_DEVICE_TABLE(of, adv7180_of_id); |
| #endif |
| |
| static struct i2c_driver adv7180_driver = { |
| .driver = { |
| .name = KBUILD_MODNAME, |
| .pm = ADV7180_PM_OPS, |
| .of_match_table = of_match_ptr(adv7180_of_id), |
| }, |
| .probe = adv7180_probe, |
| .remove = adv7180_remove, |
| .id_table = adv7180_id, |
| }; |
| |
| module_i2c_driver(adv7180_driver); |
| |
| MODULE_DESCRIPTION("Analog Devices ADV7180 video decoder driver"); |
| MODULE_AUTHOR("Mocean Laboratories"); |
| MODULE_LICENSE("GPL v2"); |