| # |
| # Light sensors |
| # |
| # When adding new entries keep the list in alphabetical order |
| |
| menu "Light sensors" |
| |
| config ADJD_S311 |
| tristate "ADJD-S311-CR999 digital color sensor" |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| depends on I2C |
| help |
| If you say yes here you get support for the Avago ADJD-S311-CR999 |
| digital color light sensor. |
| |
| This driver can also be built as a module. If so, the module |
| will be called adjd_s311. |
| |
| config APDS9300 |
| tristate "APDS9300 ambient light sensor" |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Avago APDS9300 |
| ambient light sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called apds9300. |
| |
| config CM36651 |
| depends on I2C |
| tristate "CM36651 driver" |
| help |
| Say Y here if you use cm36651. |
| This option enables proximity & RGB sensor using |
| Capella cm36651 device driver. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called cm36651. |
| |
| config GP2AP020A00F |
| tristate "Sharp GP2AP020A00F Proximity/ALS sensor" |
| depends on I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| select IRQ_WORK |
| help |
| Say Y here if you have a Sharp GP2AP020A00F proximity/ALS combo-chip |
| hooked to an I2C bus. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called gp2ap020a00f. |
| |
| config HID_SENSOR_ALS |
| depends on HID_SENSOR_HUB |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| select HID_SENSOR_IIO_COMMON |
| select HID_SENSOR_IIO_TRIGGER |
| tristate "HID ALS" |
| help |
| Say yes here to build support for the HID SENSOR |
| Ambient light sensor. |
| |
| config SENSORS_LM3533 |
| tristate "LM3533 ambient light sensor" |
| depends on MFD_LM3533 |
| help |
| If you say yes here you get support for the ambient light sensor |
| interface on National Semiconductor / TI LM3533 Lighting Power |
| chips. |
| |
| The sensor interface can be used to control the LEDs and backlights |
| of the chip through defining five light zones and three sets of |
| corresponding output-current values. |
| |
| The driver provides raw and mean adc readings along with the current |
| light zone through sysfs. A threshold event can be generated on zone |
| changes. The ALS-control output values can be set per zone for the |
| three current output channels. |
| |
| config TCS3472 |
| tristate "TAOS TCS3472 color light-to-digital converter" |
| depends on I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| If you say yes here you get support for the TAOS TCS3472 |
| family of color light-to-digital converters with IR filter. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tcs3472. |
| |
| config SENSORS_TSL2563 |
| tristate "TAOS TSL2560, TSL2561, TSL2562 and TSL2563 ambient light sensors" |
| depends on I2C |
| help |
| If you say yes here you get support for the Taos TSL2560, |
| TSL2561, TSL2562 and TSL2563 ambient light sensors. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tsl2563. |
| |
| config TSL4531 |
| tristate "TAOS TSL4531 ambient light sensors" |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the TAOS TSL4531 family |
| of ambient light sensors with direct lux output. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tsl4531. |
| |
| config VCNL4000 |
| tristate "VCNL4000 combined ALS and proximity sensor" |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Vishay VCNL4000 |
| combined ambient light and proximity sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called vcnl4000. |
| |
| endmenu |
