| /****************************************************************************/ |
| |
| /* |
| * fec.h -- Fast Ethernet Controller for Motorola ColdFire SoC |
| * processors. |
| * |
| * (C) Copyright 2000-2005, Greg Ungerer (gerg@snapgear.com) |
| * (C) Copyright 2000-2001, Lineo (www.lineo.com) |
| */ |
| |
| /****************************************************************************/ |
| #ifndef FEC_H |
| #define FEC_H |
| /****************************************************************************/ |
| |
| #include <linux/clocksource.h> |
| #include <linux/net_tstamp.h> |
| #include <linux/ptp_clock_kernel.h> |
| |
| #if defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x) || \ |
| defined(CONFIG_M520x) || defined(CONFIG_M532x) || \ |
| defined(CONFIG_ARCH_MXC) || defined(CONFIG_SOC_IMX28) |
| /* |
| * Just figures, Motorola would have to change the offsets for |
| * registers in the same peripheral device on different models |
| * of the ColdFire! |
| */ |
| #define FEC_IEVENT 0x004 /* Interrupt event reg */ |
| #define FEC_IMASK 0x008 /* Interrupt mask reg */ |
| #define FEC_R_DES_ACTIVE 0x010 /* Receive descriptor reg */ |
| #define FEC_X_DES_ACTIVE 0x014 /* Transmit descriptor reg */ |
| #define FEC_ECNTRL 0x024 /* Ethernet control reg */ |
| #define FEC_MII_DATA 0x040 /* MII manage frame reg */ |
| #define FEC_MII_SPEED 0x044 /* MII speed control reg */ |
| #define FEC_MIB_CTRLSTAT 0x064 /* MIB control/status reg */ |
| #define FEC_R_CNTRL 0x084 /* Receive control reg */ |
| #define FEC_X_CNTRL 0x0c4 /* Transmit Control reg */ |
| #define FEC_ADDR_LOW 0x0e4 /* Low 32bits MAC address */ |
| #define FEC_ADDR_HIGH 0x0e8 /* High 16bits MAC address */ |
| #define FEC_OPD 0x0ec /* Opcode + Pause duration */ |
| #define FEC_HASH_TABLE_HIGH 0x118 /* High 32bits hash table */ |
| #define FEC_HASH_TABLE_LOW 0x11c /* Low 32bits hash table */ |
| #define FEC_GRP_HASH_TABLE_HIGH 0x120 /* High 32bits hash table */ |
| #define FEC_GRP_HASH_TABLE_LOW 0x124 /* Low 32bits hash table */ |
| #define FEC_X_WMRK 0x144 /* FIFO transmit water mark */ |
| #define FEC_R_BOUND 0x14c /* FIFO receive bound reg */ |
| #define FEC_R_FSTART 0x150 /* FIFO receive start reg */ |
| #define FEC_R_DES_START 0x180 /* Receive descriptor ring */ |
| #define FEC_X_DES_START 0x184 /* Transmit descriptor ring */ |
| #define FEC_R_BUFF_SIZE 0x188 /* Maximum receive buff size */ |
| #define FEC_R_FIFO_RSFL 0x190 /* Receive FIFO section full threshold */ |
| #define FEC_R_FIFO_RSEM 0x194 /* Receive FIFO section empty threshold */ |
| #define FEC_R_FIFO_RAEM 0x198 /* Receive FIFO almost empty threshold */ |
| #define FEC_R_FIFO_RAFL 0x19c /* Receive FIFO almost full threshold */ |
| #define FEC_RACC 0x1C4 /* Receive Accelerator function */ |
| #define FEC_MIIGSK_CFGR 0x300 /* MIIGSK Configuration reg */ |
| #define FEC_MIIGSK_ENR 0x308 /* MIIGSK Enable reg */ |
| |
| #define BM_MIIGSK_CFGR_MII 0x00 |
| #define BM_MIIGSK_CFGR_RMII 0x01 |
| #define BM_MIIGSK_CFGR_FRCONT_10M 0x40 |
| |
| #define RMON_T_DROP 0x200 /* Count of frames not cntd correctly */ |
| #define RMON_T_PACKETS 0x204 /* RMON TX packet count */ |
| #define RMON_T_BC_PKT 0x208 /* RMON TX broadcast pkts */ |
| #define RMON_T_MC_PKT 0x20C /* RMON TX multicast pkts */ |
| #define RMON_T_CRC_ALIGN 0x210 /* RMON TX pkts with CRC align err */ |
| #define RMON_T_UNDERSIZE 0x214 /* RMON TX pkts < 64 bytes, good CRC */ |
| #define RMON_T_OVERSIZE 0x218 /* RMON TX pkts > MAX_FL bytes good CRC */ |
| #define RMON_T_FRAG 0x21C /* RMON TX pkts < 64 bytes, bad CRC */ |
| #define RMON_T_JAB 0x220 /* RMON TX pkts > MAX_FL bytes, bad CRC */ |
| #define RMON_T_COL 0x224 /* RMON TX collision count */ |
| #define RMON_T_P64 0x228 /* RMON TX 64 byte pkts */ |
| #define RMON_T_P65TO127 0x22C /* RMON TX 65 to 127 byte pkts */ |
| #define RMON_T_P128TO255 0x230 /* RMON TX 128 to 255 byte pkts */ |
| #define RMON_T_P256TO511 0x234 /* RMON TX 256 to 511 byte pkts */ |
| #define RMON_T_P512TO1023 0x238 /* RMON TX 512 to 1023 byte pkts */ |
| #define RMON_T_P1024TO2047 0x23C /* RMON TX 1024 to 2047 byte pkts */ |
| #define RMON_T_P_GTE2048 0x240 /* RMON TX pkts > 2048 bytes */ |
| #define RMON_T_OCTETS 0x244 /* RMON TX octets */ |
| #define IEEE_T_DROP 0x248 /* Count of frames not counted crtly */ |
| #define IEEE_T_FRAME_OK 0x24C /* Frames tx'd OK */ |
| #define IEEE_T_1COL 0x250 /* Frames tx'd with single collision */ |
| #define IEEE_T_MCOL 0x254 /* Frames tx'd with multiple collision */ |
| #define IEEE_T_DEF 0x258 /* Frames tx'd after deferral delay */ |
| #define IEEE_T_LCOL 0x25C /* Frames tx'd with late collision */ |
| #define IEEE_T_EXCOL 0x260 /* Frames tx'd with excesv collisions */ |
| #define IEEE_T_MACERR 0x264 /* Frames tx'd with TX FIFO underrun */ |
| #define IEEE_T_CSERR 0x268 /* Frames tx'd with carrier sense err */ |
| #define IEEE_T_SQE 0x26C /* Frames tx'd with SQE err */ |
| #define IEEE_T_FDXFC 0x270 /* Flow control pause frames tx'd */ |
| #define IEEE_T_OCTETS_OK 0x274 /* Octet count for frames tx'd w/o err */ |
| #define RMON_R_PACKETS 0x284 /* RMON RX packet count */ |
| #define RMON_R_BC_PKT 0x288 /* RMON RX broadcast pkts */ |
| #define RMON_R_MC_PKT 0x28C /* RMON RX multicast pkts */ |
| #define RMON_R_CRC_ALIGN 0x290 /* RMON RX pkts with CRC alignment err */ |
| #define RMON_R_UNDERSIZE 0x294 /* RMON RX pkts < 64 bytes, good CRC */ |
| #define RMON_R_OVERSIZE 0x298 /* RMON RX pkts > MAX_FL bytes good CRC */ |
| #define RMON_R_FRAG 0x29C /* RMON RX pkts < 64 bytes, bad CRC */ |
| #define RMON_R_JAB 0x2A0 /* RMON RX pkts > MAX_FL bytes, bad CRC */ |
| #define RMON_R_RESVD_O 0x2A4 /* Reserved */ |
| #define RMON_R_P64 0x2A8 /* RMON RX 64 byte pkts */ |
| #define RMON_R_P65TO127 0x2AC /* RMON RX 65 to 127 byte pkts */ |
| #define RMON_R_P128TO255 0x2B0 /* RMON RX 128 to 255 byte pkts */ |
| #define RMON_R_P256TO511 0x2B4 /* RMON RX 256 to 511 byte pkts */ |
| #define RMON_R_P512TO1023 0x2B8 /* RMON RX 512 to 1023 byte pkts */ |
| #define RMON_R_P1024TO2047 0x2BC /* RMON RX 1024 to 2047 byte pkts */ |
| #define RMON_R_P_GTE2048 0x2C0 /* RMON RX pkts > 2048 bytes */ |
| #define RMON_R_OCTETS 0x2C4 /* RMON RX octets */ |
| #define IEEE_R_DROP 0x2C8 /* Count frames not counted correctly */ |
| #define IEEE_R_FRAME_OK 0x2CC /* Frames rx'd OK */ |
| #define IEEE_R_CRC 0x2D0 /* Frames rx'd with CRC err */ |
| #define IEEE_R_ALIGN 0x2D4 /* Frames rx'd with alignment err */ |
| #define IEEE_R_MACERR 0x2D8 /* Receive FIFO overflow count */ |
| #define IEEE_R_FDXFC 0x2DC /* Flow control pause frames rx'd */ |
| #define IEEE_R_OCTETS_OK 0x2E0 /* Octet cnt for frames rx'd w/o err */ |
| |
| #else |
| |
| #define FEC_ECNTRL 0x000 /* Ethernet control reg */ |
| #define FEC_IEVENT 0x004 /* Interrupt even reg */ |
| #define FEC_IMASK 0x008 /* Interrupt mask reg */ |
| #define FEC_IVEC 0x00c /* Interrupt vec status reg */ |
| #define FEC_R_DES_ACTIVE 0x010 /* Receive descriptor reg */ |
| #define FEC_X_DES_ACTIVE 0x014 /* Transmit descriptor reg */ |
| #define FEC_MII_DATA 0x040 /* MII manage frame reg */ |
| #define FEC_MII_SPEED 0x044 /* MII speed control reg */ |
| #define FEC_R_BOUND 0x08c /* FIFO receive bound reg */ |
| #define FEC_R_FSTART 0x090 /* FIFO receive start reg */ |
| #define FEC_X_WMRK 0x0a4 /* FIFO transmit water mark */ |
| #define FEC_X_FSTART 0x0ac /* FIFO transmit start reg */ |
| #define FEC_R_CNTRL 0x104 /* Receive control reg */ |
| #define FEC_MAX_FRM_LEN 0x108 /* Maximum frame length reg */ |
| #define FEC_X_CNTRL 0x144 /* Transmit Control reg */ |
| #define FEC_ADDR_LOW 0x3c0 /* Low 32bits MAC address */ |
| #define FEC_ADDR_HIGH 0x3c4 /* High 16bits MAC address */ |
| #define FEC_GRP_HASH_TABLE_HIGH 0x3c8 /* High 32bits hash table */ |
| #define FEC_GRP_HASH_TABLE_LOW 0x3cc /* Low 32bits hash table */ |
| #define FEC_R_DES_START 0x3d0 /* Receive descriptor ring */ |
| #define FEC_X_DES_START 0x3d4 /* Transmit descriptor ring */ |
| #define FEC_R_BUFF_SIZE 0x3d8 /* Maximum receive buff size */ |
| #define FEC_FIFO_RAM 0x400 /* FIFO RAM buffer */ |
| |
| #endif /* CONFIG_M5272 */ |
| |
| |
| /* |
| * Define the buffer descriptor structure. |
| */ |
| #if defined(CONFIG_ARCH_MXC) || defined(CONFIG_SOC_IMX28) |
| struct bufdesc { |
| unsigned short cbd_datlen; /* Data length */ |
| unsigned short cbd_sc; /* Control and status info */ |
| unsigned long cbd_bufaddr; /* Buffer address */ |
| }; |
| #else |
| struct bufdesc { |
| unsigned short cbd_sc; /* Control and status info */ |
| unsigned short cbd_datlen; /* Data length */ |
| unsigned long cbd_bufaddr; /* Buffer address */ |
| }; |
| #endif |
| |
| struct bufdesc_ex { |
| struct bufdesc desc; |
| unsigned long cbd_esc; |
| unsigned long cbd_prot; |
| unsigned long cbd_bdu; |
| unsigned long ts; |
| unsigned short res0[4]; |
| }; |
| |
| /* |
| * The following definitions courtesy of commproc.h, which where |
| * Copyright (c) 1997 Dan Malek (dmalek@jlc.net). |
| */ |
| #define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */ |
| #define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */ |
| #define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */ |
| #define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */ |
| #define BD_SC_CM ((ushort)0x0200) /* Continuous mode */ |
| #define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */ |
| #define BD_SC_P ((ushort)0x0100) /* xmt preamble */ |
| #define BD_SC_BR ((ushort)0x0020) /* Break received */ |
| #define BD_SC_FR ((ushort)0x0010) /* Framing error */ |
| #define BD_SC_PR ((ushort)0x0008) /* Parity error */ |
| #define BD_SC_OV ((ushort)0x0002) /* Overrun */ |
| #define BD_SC_CD ((ushort)0x0001) /* ?? */ |
| |
| /* Buffer descriptor control/status used by Ethernet receive. |
| */ |
| #define BD_ENET_RX_EMPTY ((ushort)0x8000) |
| #define BD_ENET_RX_WRAP ((ushort)0x2000) |
| #define BD_ENET_RX_INTR ((ushort)0x1000) |
| #define BD_ENET_RX_LAST ((ushort)0x0800) |
| #define BD_ENET_RX_FIRST ((ushort)0x0400) |
| #define BD_ENET_RX_MISS ((ushort)0x0100) |
| #define BD_ENET_RX_LG ((ushort)0x0020) |
| #define BD_ENET_RX_NO ((ushort)0x0010) |
| #define BD_ENET_RX_SH ((ushort)0x0008) |
| #define BD_ENET_RX_CR ((ushort)0x0004) |
| #define BD_ENET_RX_OV ((ushort)0x0002) |
| #define BD_ENET_RX_CL ((ushort)0x0001) |
| #define BD_ENET_RX_STATS ((ushort)0x013f) /* All status bits */ |
| |
| /* Enhanced buffer descriptor control/status used by Ethernet receive */ |
| #define BD_ENET_RX_VLAN 0x00000004 |
| |
| /* Buffer descriptor control/status used by Ethernet transmit. |
| */ |
| #define BD_ENET_TX_READY ((ushort)0x8000) |
| #define BD_ENET_TX_PAD ((ushort)0x4000) |
| #define BD_ENET_TX_WRAP ((ushort)0x2000) |
| #define BD_ENET_TX_INTR ((ushort)0x1000) |
| #define BD_ENET_TX_LAST ((ushort)0x0800) |
| #define BD_ENET_TX_TC ((ushort)0x0400) |
| #define BD_ENET_TX_DEF ((ushort)0x0200) |
| #define BD_ENET_TX_HB ((ushort)0x0100) |
| #define BD_ENET_TX_LC ((ushort)0x0080) |
| #define BD_ENET_TX_RL ((ushort)0x0040) |
| #define BD_ENET_TX_RCMASK ((ushort)0x003c) |
| #define BD_ENET_TX_UN ((ushort)0x0002) |
| #define BD_ENET_TX_CSL ((ushort)0x0001) |
| #define BD_ENET_TX_STATS ((ushort)0x0fff) /* All status bits */ |
| |
| /*enhanced buffer descriptor control/status used by Ethernet transmit*/ |
| #define BD_ENET_TX_INT 0x40000000 |
| #define BD_ENET_TX_TS 0x20000000 |
| #define BD_ENET_TX_PINS 0x10000000 |
| #define BD_ENET_TX_IINS 0x08000000 |
| |
| |
| /* This device has up to three irqs on some platforms */ |
| #define FEC_IRQ_NUM 3 |
| |
| /* The number of Tx and Rx buffers. These are allocated from the page |
| * pool. The code may assume these are power of two, so it it best |
| * to keep them that size. |
| * We don't need to allocate pages for the transmitter. We just use |
| * the skbuffer directly. |
| */ |
| |
| #define FEC_ENET_RX_PAGES 8 |
| #define FEC_ENET_RX_FRSIZE 2048 |
| #define FEC_ENET_RX_FRPPG (PAGE_SIZE / FEC_ENET_RX_FRSIZE) |
| #define RX_RING_SIZE (FEC_ENET_RX_FRPPG * FEC_ENET_RX_PAGES) |
| #define FEC_ENET_TX_FRSIZE 2048 |
| #define FEC_ENET_TX_FRPPG (PAGE_SIZE / FEC_ENET_TX_FRSIZE) |
| #define TX_RING_SIZE 512 /* Must be power of two */ |
| #define TX_RING_MOD_MASK 511 /* for this to work */ |
| |
| #define BD_ENET_RX_INT 0x00800000 |
| #define BD_ENET_RX_PTP ((ushort)0x0400) |
| #define BD_ENET_RX_ICE 0x00000020 |
| #define BD_ENET_RX_PCR 0x00000010 |
| #define FLAG_RX_CSUM_ENABLED (BD_ENET_RX_ICE | BD_ENET_RX_PCR) |
| #define FLAG_RX_CSUM_ERROR (BD_ENET_RX_ICE | BD_ENET_RX_PCR) |
| |
| struct fec_enet_delayed_work { |
| struct delayed_work delay_work; |
| bool timeout; |
| bool trig_tx; |
| }; |
| |
| /* The FEC buffer descriptors track the ring buffers. The rx_bd_base and |
| * tx_bd_base always point to the base of the buffer descriptors. The |
| * cur_rx and cur_tx point to the currently available buffer. |
| * The dirty_tx tracks the current buffer that is being sent by the |
| * controller. The cur_tx and dirty_tx are equal under both completely |
| * empty and completely full conditions. The empty/ready indicator in |
| * the buffer descriptor determines the actual condition. |
| */ |
| struct fec_enet_private { |
| /* Hardware registers of the FEC device */ |
| void __iomem *hwp; |
| |
| struct net_device *netdev; |
| |
| struct clk *clk_ipg; |
| struct clk *clk_ahb; |
| struct clk *clk_enet_out; |
| struct clk *clk_ptp; |
| |
| /* The saved address of a sent-in-place packet/buffer, for skfree(). */ |
| unsigned char *tx_bounce[TX_RING_SIZE]; |
| struct sk_buff *tx_skbuff[TX_RING_SIZE]; |
| struct sk_buff *rx_skbuff[RX_RING_SIZE]; |
| |
| /* CPM dual port RAM relative addresses */ |
| dma_addr_t bd_dma; |
| /* Address of Rx and Tx buffers */ |
| struct bufdesc *rx_bd_base; |
| struct bufdesc *tx_bd_base; |
| /* The next free ring entry */ |
| struct bufdesc *cur_rx, *cur_tx; |
| /* The ring entries to be free()ed */ |
| struct bufdesc *dirty_tx; |
| |
| unsigned short bufdesc_size; |
| unsigned short tx_ring_size; |
| unsigned short rx_ring_size; |
| unsigned short tx_stop_threshold; |
| unsigned short tx_wake_threshold; |
| |
| /* Software TSO */ |
| char *tso_hdrs; |
| dma_addr_t tso_hdrs_dma; |
| |
| struct platform_device *pdev; |
| |
| int opened; |
| int dev_id; |
| |
| /* Phylib and MDIO interface */ |
| struct mii_bus *mii_bus; |
| struct phy_device *phy_dev; |
| int mii_timeout; |
| uint phy_speed; |
| phy_interface_t phy_interface; |
| int link; |
| int full_duplex; |
| int speed; |
| struct completion mdio_done; |
| int irq[FEC_IRQ_NUM]; |
| int bufdesc_ex; |
| int pause_flag; |
| |
| struct napi_struct napi; |
| int csum_flags; |
| |
| struct ptp_clock *ptp_clock; |
| struct ptp_clock_info ptp_caps; |
| unsigned long last_overflow_check; |
| spinlock_t tmreg_lock; |
| struct cyclecounter cc; |
| struct timecounter tc; |
| int rx_hwtstamp_filter; |
| u32 base_incval; |
| u32 cycle_speed; |
| int hwts_rx_en; |
| int hwts_tx_en; |
| struct timer_list time_keep; |
| struct fec_enet_delayed_work delay_work; |
| struct regulator *reg_phy; |
| }; |
| |
| void fec_ptp_init(struct platform_device *pdev); |
| void fec_ptp_start_cyclecounter(struct net_device *ndev); |
| int fec_ptp_set(struct net_device *ndev, struct ifreq *ifr); |
| int fec_ptp_get(struct net_device *ndev, struct ifreq *ifr); |
| |
| /****************************************************************************/ |
| #endif /* FEC_H */ |