arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (c) 2019 BayLibre, SAS
 * Author: Neil Armstrong <narmstrong@baylibre.com>
 */

/dts-v1/;

#include "meson-sm1.dtsi"
#include "meson-khadas-vim3.dtsi"
#include <dt-bindings/sound/meson-g12a-tohdmitx.h>

/ {
	compatible = "khadas,vim3l", "amlogic,sm1";
	model = "Khadas VIM3L";

	vddcpu: regulator-vddcpu {
		/*
		 * Silergy SY8030DEC Regulator.
		 */
		compatible = "pwm-regulator";

		regulator-name = "VDDCPU";
		regulator-min-microvolt = <690000>;
		regulator-max-microvolt = <1050000>;

		vin-supply = <&vsys_3v3>;

		pwms = <&pwm_AO_cd 1 1250 0>;
		pwm-dutycycle-range = <100 0>;

		regulator-boot-on;
		regulator-always-on;
	};

	sound {
		compatible = "amlogic,axg-sound-card";
		model = "SM1-KHADAS-VIM3L";
		audio-aux-devs = <&tdmout_a>;
		audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0",
				"TDMOUT_A IN 1", "FRDDR_B OUT 0",
				"TDMOUT_A IN 2", "FRDDR_C OUT 0",
				"TDM_A Playback", "TDMOUT_A OUT";

		assigned-clocks = <&clkc CLKID_MPLL2>,
				  <&clkc CLKID_MPLL0>,
				  <&clkc CLKID_MPLL1>;
		assigned-clock-parents = <0>, <0>, <0>;
		assigned-clock-rates = <294912000>,
				       <270950400>,
				       <393216000>;
		status = "okay";

		dai-link-0 {
			sound-dai = <&frddr_a>;
		};

		dai-link-1 {
			sound-dai = <&frddr_b>;
		};

		dai-link-2 {
			sound-dai = <&frddr_c>;
		};

		/* 8ch hdmi interface */
		dai-link-3 {
			sound-dai = <&tdmif_a>;
			dai-format = "i2s";
			dai-tdm-slot-tx-mask-0 = <1 1>;
			dai-tdm-slot-tx-mask-1 = <1 1>;
			dai-tdm-slot-tx-mask-2 = <1 1>;
			dai-tdm-slot-tx-mask-3 = <1 1>;
			mclk-fs = <256>;

			codec {
				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>;
			};
		};

		/* hdmi glue */
		dai-link-4 {
			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;

			codec {
				sound-dai = <&hdmi_tx>;
			};
		};
	};
};

&arb {
	status = "okay";
};

&clkc_audio {
	status = "okay";
};

&cpu0 {
	cpu-supply = <&vddcpu>;
	operating-points-v2 = <&cpu_opp_table>;
	clocks = <&clkc CLKID_CPU_CLK>;
	clock-latency = <50000>;
};

&cpu1 {
	cpu-supply = <&vddcpu>;
	operating-points-v2 = <&cpu_opp_table>;
	clocks = <&clkc CLKID_CPU1_CLK>;
	clock-latency = <50000>;
};

&cpu2 {
	cpu-supply = <&vddcpu>;
	operating-points-v2 = <&cpu_opp_table>;
	clocks = <&clkc CLKID_CPU2_CLK>;
	clock-latency = <50000>;
};

&cpu3 {
	cpu-supply = <&vddcpu>;
	operating-points-v2 = <&cpu_opp_table>;
	clocks = <&clkc CLKID_CPU3_CLK>;
	clock-latency = <50000>;
};

&frddr_a {
	status = "okay";
};

&frddr_b {
	status = "okay";
};

&frddr_c {
	status = "okay";
};

&pwm_AO_cd {
	pinctrl-0 = <&pwm_ao_d_e_pins>;
	pinctrl-names = "default";
	clocks = <&xtal>;
	clock-names = "clkin1";
	status = "okay";
};

/*
 * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
 * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
 * an USB3.0 Type A connector and a M.2 Key M slot.
 * The PHY driving these differential lines is shared between
 * the USB3.0 controller and the PCIe Controller, thus only
 * a single controller can use it.
 * If the MCU is configured to mux the PCIe/USB3.0 differential lines
 * to the M.2 Key M slot, uncomment the following block to disable
 * USB3.0 from the USB Complex and enable the PCIe controller.
 * The End User is not expected to uncomment the following except for
 * testing purposes, but instead rely on the firmware/bootloader to
 * update these nodes accordingly if PCIe mode is selected by the MCU.
 */
/*
&pcie {
	status = "okay";
};

&sd_emmc_a {
	sd-uhs-sdr50;
};

&usb {
	phys = <&usb2_phy0>, <&usb2_phy1>;
	phy-names = "usb2-phy0", "usb2-phy1";
};
 */

&tdmif_a {
	status = "okay";
};

&tdmout_a {
	status = "okay";
};

&tohdmitx {
	status = "okay";
};