| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Atmel AT45xxx DataFlash MTD driver for lightweight SPI framework |
| * |
| * Largely derived from at91_dataflash.c: |
| * Copyright (C) 2003-2005 SAN People (Pty) Ltd |
| */ |
| #include <linux/module.h> |
| #include <linux/slab.h> |
| #include <linux/delay.h> |
| #include <linux/device.h> |
| #include <linux/mutex.h> |
| #include <linux/err.h> |
| #include <linux/math64.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| |
| #include <linux/spi/spi.h> |
| #include <linux/spi/flash.h> |
| |
| #include <linux/mtd/mtd.h> |
| #include <linux/mtd/partitions.h> |
| |
| /* |
| * DataFlash is a kind of SPI flash. Most AT45 chips have two buffers in |
| * each chip, which may be used for double buffered I/O; but this driver |
| * doesn't (yet) use these for any kind of i/o overlap or prefetching. |
| * |
| * Sometimes DataFlash is packaged in MMC-format cards, although the |
| * MMC stack can't (yet?) distinguish between MMC and DataFlash |
| * protocols during enumeration. |
| */ |
| |
| /* reads can bypass the buffers */ |
| #define OP_READ_CONTINUOUS 0xE8 |
| #define OP_READ_PAGE 0xD2 |
| |
| /* group B requests can run even while status reports "busy" */ |
| #define OP_READ_STATUS 0xD7 /* group B */ |
| |
| /* move data between host and buffer */ |
| #define OP_READ_BUFFER1 0xD4 /* group B */ |
| #define OP_READ_BUFFER2 0xD6 /* group B */ |
| #define OP_WRITE_BUFFER1 0x84 /* group B */ |
| #define OP_WRITE_BUFFER2 0x87 /* group B */ |
| |
| /* erasing flash */ |
| #define OP_ERASE_PAGE 0x81 |
| #define OP_ERASE_BLOCK 0x50 |
| |
| /* move data between buffer and flash */ |
| #define OP_TRANSFER_BUF1 0x53 |
| #define OP_TRANSFER_BUF2 0x55 |
| #define OP_MREAD_BUFFER1 0xD4 |
| #define OP_MREAD_BUFFER2 0xD6 |
| #define OP_MWERASE_BUFFER1 0x83 |
| #define OP_MWERASE_BUFFER2 0x86 |
| #define OP_MWRITE_BUFFER1 0x88 /* sector must be pre-erased */ |
| #define OP_MWRITE_BUFFER2 0x89 /* sector must be pre-erased */ |
| |
| /* write to buffer, then write-erase to flash */ |
| #define OP_PROGRAM_VIA_BUF1 0x82 |
| #define OP_PROGRAM_VIA_BUF2 0x85 |
| |
| /* compare buffer to flash */ |
| #define OP_COMPARE_BUF1 0x60 |
| #define OP_COMPARE_BUF2 0x61 |
| |
| /* read flash to buffer, then write-erase to flash */ |
| #define OP_REWRITE_VIA_BUF1 0x58 |
| #define OP_REWRITE_VIA_BUF2 0x59 |
| |
| /* newer chips report JEDEC manufacturer and device IDs; chip |
| * serial number and OTP bits; and per-sector writeprotect. |
| */ |
| #define OP_READ_ID 0x9F |
| #define OP_READ_SECURITY 0x77 |
| #define OP_WRITE_SECURITY_REVC 0x9A |
| #define OP_WRITE_SECURITY 0x9B /* revision D */ |
| |
| #define CFI_MFR_ATMEL 0x1F |
| |
| #define DATAFLASH_SHIFT_EXTID 24 |
| #define DATAFLASH_SHIFT_ID 40 |
| |
| struct dataflash { |
| u8 command[4]; |
| char name[24]; |
| |
| unsigned short page_offset; /* offset in flash address */ |
| unsigned int page_size; /* of bytes per page */ |
| |
| struct mutex lock; |
| struct spi_device *spi; |
| |
| struct mtd_info mtd; |
| }; |
| |
| #ifdef CONFIG_OF |
| static const struct of_device_id dataflash_dt_ids[] = { |
| { .compatible = "atmel,at45", }, |
| { .compatible = "atmel,dataflash", }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, dataflash_dt_ids); |
| #endif |
| |
| static const struct spi_device_id dataflash_spi_ids[] = { |
| { .name = "at45", }, |
| { .name = "dataflash", }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(spi, dataflash_spi_ids); |
| |
| /* ......................................................................... */ |
| |
| /* |
| * Return the status of the DataFlash device. |
| */ |
| static inline int dataflash_status(struct spi_device *spi) |
| { |
| /* NOTE: at45db321c over 25 MHz wants to write |
| * a dummy byte after the opcode... |
| */ |
| return spi_w8r8(spi, OP_READ_STATUS); |
| } |
| |
| /* |
| * Poll the DataFlash device until it is READY. |
| * This usually takes 5-20 msec or so; more for sector erase. |
| */ |
| static int dataflash_waitready(struct spi_device *spi) |
| { |
| int status; |
| |
| for (;;) { |
| status = dataflash_status(spi); |
| if (status < 0) { |
| dev_dbg(&spi->dev, "status %d?\n", status); |
| status = 0; |
| } |
| |
| if (status & (1 << 7)) /* RDY/nBSY */ |
| return status; |
| |
| usleep_range(3000, 4000); |
| } |
| } |
| |
| /* ......................................................................... */ |
| |
| /* |
| * Erase pages of flash. |
| */ |
| static int dataflash_erase(struct mtd_info *mtd, struct erase_info *instr) |
| { |
| struct dataflash *priv = mtd->priv; |
| struct spi_device *spi = priv->spi; |
| struct spi_transfer x = { }; |
| struct spi_message msg; |
| unsigned blocksize = priv->page_size << 3; |
| u8 *command; |
| u32 rem; |
| |
| dev_dbg(&spi->dev, "erase addr=0x%llx len 0x%llx\n", |
| (long long)instr->addr, (long long)instr->len); |
| |
| div_u64_rem(instr->len, priv->page_size, &rem); |
| if (rem) |
| return -EINVAL; |
| div_u64_rem(instr->addr, priv->page_size, &rem); |
| if (rem) |
| return -EINVAL; |
| |
| spi_message_init(&msg); |
| |
| x.tx_buf = command = priv->command; |
| x.len = 4; |
| spi_message_add_tail(&x, &msg); |
| |
| mutex_lock(&priv->lock); |
| while (instr->len > 0) { |
| unsigned int pageaddr; |
| int status; |
| int do_block; |
| |
| /* Calculate flash page address; use block erase (for speed) if |
| * we're at a block boundary and need to erase the whole block. |
| */ |
| pageaddr = div_u64(instr->addr, priv->page_size); |
| do_block = (pageaddr & 0x7) == 0 && instr->len >= blocksize; |
| pageaddr = pageaddr << priv->page_offset; |
| |
| command[0] = do_block ? OP_ERASE_BLOCK : OP_ERASE_PAGE; |
| command[1] = (u8)(pageaddr >> 16); |
| command[2] = (u8)(pageaddr >> 8); |
| command[3] = 0; |
| |
| dev_dbg(&spi->dev, "ERASE %s: (%x) %x %x %x [%i]\n", |
| do_block ? "block" : "page", |
| command[0], command[1], command[2], command[3], |
| pageaddr); |
| |
| status = spi_sync(spi, &msg); |
| (void) dataflash_waitready(spi); |
| |
| if (status < 0) { |
| dev_err(&spi->dev, "erase %x, err %d\n", |
| pageaddr, status); |
| /* REVISIT: can retry instr->retries times; or |
| * giveup and instr->fail_addr = instr->addr; |
| */ |
| continue; |
| } |
| |
| if (do_block) { |
| instr->addr += blocksize; |
| instr->len -= blocksize; |
| } else { |
| instr->addr += priv->page_size; |
| instr->len -= priv->page_size; |
| } |
| } |
| mutex_unlock(&priv->lock); |
| |
| return 0; |
| } |
| |
| /* |
| * Read from the DataFlash device. |
| * from : Start offset in flash device |
| * len : Amount to read |
| * retlen : About of data actually read |
| * buf : Buffer containing the data |
| */ |
| static int dataflash_read(struct mtd_info *mtd, loff_t from, size_t len, |
| size_t *retlen, u_char *buf) |
| { |
| struct dataflash *priv = mtd->priv; |
| struct spi_transfer x[2] = { }; |
| struct spi_message msg; |
| unsigned int addr; |
| u8 *command; |
| int status; |
| |
| dev_dbg(&priv->spi->dev, "read 0x%x..0x%x\n", |
| (unsigned int)from, (unsigned int)(from + len)); |
| |
| /* Calculate flash page/byte address */ |
| addr = (((unsigned)from / priv->page_size) << priv->page_offset) |
| + ((unsigned)from % priv->page_size); |
| |
| command = priv->command; |
| |
| dev_dbg(&priv->spi->dev, "READ: (%x) %x %x %x\n", |
| command[0], command[1], command[2], command[3]); |
| |
| spi_message_init(&msg); |
| |
| x[0].tx_buf = command; |
| x[0].len = 8; |
| spi_message_add_tail(&x[0], &msg); |
| |
| x[1].rx_buf = buf; |
| x[1].len = len; |
| spi_message_add_tail(&x[1], &msg); |
| |
| mutex_lock(&priv->lock); |
| |
| /* Continuous read, max clock = f(car) which may be less than |
| * the peak rate available. Some chips support commands with |
| * fewer "don't care" bytes. Both buffers stay unchanged. |
| */ |
| command[0] = OP_READ_CONTINUOUS; |
| command[1] = (u8)(addr >> 16); |
| command[2] = (u8)(addr >> 8); |
| command[3] = (u8)(addr >> 0); |
| /* plus 4 "don't care" bytes */ |
| |
| status = spi_sync(priv->spi, &msg); |
| mutex_unlock(&priv->lock); |
| |
| if (status >= 0) { |
| *retlen = msg.actual_length - 8; |
| status = 0; |
| } else |
| dev_dbg(&priv->spi->dev, "read %x..%x --> %d\n", |
| (unsigned)from, (unsigned)(from + len), |
| status); |
| return status; |
| } |
| |
| /* |
| * Write to the DataFlash device. |
| * to : Start offset in flash device |
| * len : Amount to write |
| * retlen : Amount of data actually written |
| * buf : Buffer containing the data |
| */ |
| static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, |
| size_t * retlen, const u_char * buf) |
| { |
| struct dataflash *priv = mtd->priv; |
| struct spi_device *spi = priv->spi; |
| struct spi_transfer x[2] = { }; |
| struct spi_message msg; |
| unsigned int pageaddr, addr, offset, writelen; |
| size_t remaining = len; |
| u_char *writebuf = (u_char *) buf; |
| int status = -EINVAL; |
| u8 *command; |
| |
| dev_dbg(&spi->dev, "write 0x%x..0x%x\n", |
| (unsigned int)to, (unsigned int)(to + len)); |
| |
| spi_message_init(&msg); |
| |
| x[0].tx_buf = command = priv->command; |
| x[0].len = 4; |
| spi_message_add_tail(&x[0], &msg); |
| |
| pageaddr = ((unsigned)to / priv->page_size); |
| offset = ((unsigned)to % priv->page_size); |
| if (offset + len > priv->page_size) |
| writelen = priv->page_size - offset; |
| else |
| writelen = len; |
| |
| mutex_lock(&priv->lock); |
| while (remaining > 0) { |
| dev_dbg(&spi->dev, "write @ %i:%i len=%i\n", |
| pageaddr, offset, writelen); |
| |
| /* REVISIT: |
| * (a) each page in a sector must be rewritten at least |
| * once every 10K sibling erase/program operations. |
| * (b) for pages that are already erased, we could |
| * use WRITE+MWRITE not PROGRAM for ~30% speedup. |
| * (c) WRITE to buffer could be done while waiting for |
| * a previous MWRITE/MWERASE to complete ... |
| * (d) error handling here seems to be mostly missing. |
| * |
| * Two persistent bits per page, plus a per-sector counter, |
| * could support (a) and (b) ... we might consider using |
| * the second half of sector zero, which is just one block, |
| * to track that state. (On AT91, that sector should also |
| * support boot-from-DataFlash.) |
| */ |
| |
| addr = pageaddr << priv->page_offset; |
| |
| /* (1) Maybe transfer partial page to Buffer1 */ |
| if (writelen != priv->page_size) { |
| command[0] = OP_TRANSFER_BUF1; |
| command[1] = (addr & 0x00FF0000) >> 16; |
| command[2] = (addr & 0x0000FF00) >> 8; |
| command[3] = 0; |
| |
| dev_dbg(&spi->dev, "TRANSFER: (%x) %x %x %x\n", |
| command[0], command[1], command[2], command[3]); |
| |
| status = spi_sync(spi, &msg); |
| if (status < 0) |
| dev_dbg(&spi->dev, "xfer %u -> %d\n", |
| addr, status); |
| |
| (void) dataflash_waitready(priv->spi); |
| } |
| |
| /* (2) Program full page via Buffer1 */ |
| addr += offset; |
| command[0] = OP_PROGRAM_VIA_BUF1; |
| command[1] = (addr & 0x00FF0000) >> 16; |
| command[2] = (addr & 0x0000FF00) >> 8; |
| command[3] = (addr & 0x000000FF); |
| |
| dev_dbg(&spi->dev, "PROGRAM: (%x) %x %x %x\n", |
| command[0], command[1], command[2], command[3]); |
| |
| x[1].tx_buf = writebuf; |
| x[1].len = writelen; |
| spi_message_add_tail(x + 1, &msg); |
| status = spi_sync(spi, &msg); |
| spi_transfer_del(x + 1); |
| if (status < 0) |
| dev_dbg(&spi->dev, "pgm %u/%u -> %d\n", |
| addr, writelen, status); |
| |
| (void) dataflash_waitready(priv->spi); |
| |
| |
| #ifdef CONFIG_MTD_DATAFLASH_WRITE_VERIFY |
| |
| /* (3) Compare to Buffer1 */ |
| addr = pageaddr << priv->page_offset; |
| command[0] = OP_COMPARE_BUF1; |
| command[1] = (addr & 0x00FF0000) >> 16; |
| command[2] = (addr & 0x0000FF00) >> 8; |
| command[3] = 0; |
| |
| dev_dbg(&spi->dev, "COMPARE: (%x) %x %x %x\n", |
| command[0], command[1], command[2], command[3]); |
| |
| status = spi_sync(spi, &msg); |
| if (status < 0) |
| dev_dbg(&spi->dev, "compare %u -> %d\n", |
| addr, status); |
| |
| status = dataflash_waitready(priv->spi); |
| |
| /* Check result of the compare operation */ |
| if (status & (1 << 6)) { |
| dev_err(&spi->dev, "compare page %u, err %d\n", |
| pageaddr, status); |
| remaining = 0; |
| status = -EIO; |
| break; |
| } else |
| status = 0; |
| |
| #endif /* CONFIG_MTD_DATAFLASH_WRITE_VERIFY */ |
| |
| remaining = remaining - writelen; |
| pageaddr++; |
| offset = 0; |
| writebuf += writelen; |
| *retlen += writelen; |
| |
| if (remaining > priv->page_size) |
| writelen = priv->page_size; |
| else |
| writelen = remaining; |
| } |
| mutex_unlock(&priv->lock); |
| |
| return status; |
| } |
| |
| /* ......................................................................... */ |
| |
| #ifdef CONFIG_MTD_DATAFLASH_OTP |
| |
| static int dataflash_get_otp_info(struct mtd_info *mtd, size_t len, |
| size_t *retlen, struct otp_info *info) |
| { |
| /* Report both blocks as identical: bytes 0..64, locked. |
| * Unless the user block changed from all-ones, we can't |
| * tell whether it's still writable; so we assume it isn't. |
| */ |
| info->start = 0; |
| info->length = 64; |
| info->locked = 1; |
| *retlen = sizeof(*info); |
| return 0; |
| } |
| |
| static ssize_t otp_read(struct spi_device *spi, unsigned base, |
| u8 *buf, loff_t off, size_t len) |
| { |
| struct spi_message m; |
| size_t l; |
| u8 *scratch; |
| struct spi_transfer t; |
| int status; |
| |
| if (off > 64) |
| return -EINVAL; |
| |
| if ((off + len) > 64) |
| len = 64 - off; |
| |
| spi_message_init(&m); |
| |
| l = 4 + base + off + len; |
| scratch = kzalloc(l, GFP_KERNEL); |
| if (!scratch) |
| return -ENOMEM; |
| |
| /* OUT: OP_READ_SECURITY, 3 don't-care bytes, zeroes |
| * IN: ignore 4 bytes, data bytes 0..N (max 127) |
| */ |
| scratch[0] = OP_READ_SECURITY; |
| |
| memset(&t, 0, sizeof t); |
| t.tx_buf = scratch; |
| t.rx_buf = scratch; |
| t.len = l; |
| spi_message_add_tail(&t, &m); |
| |
| dataflash_waitready(spi); |
| |
| status = spi_sync(spi, &m); |
| if (status >= 0) { |
| memcpy(buf, scratch + 4 + base + off, len); |
| status = len; |
| } |
| |
| kfree(scratch); |
| return status; |
| } |
| |
| static int dataflash_read_fact_otp(struct mtd_info *mtd, |
| loff_t from, size_t len, size_t *retlen, u_char *buf) |
| { |
| struct dataflash *priv = mtd->priv; |
| int status; |
| |
| /* 64 bytes, from 0..63 ... start at 64 on-chip */ |
| mutex_lock(&priv->lock); |
| status = otp_read(priv->spi, 64, buf, from, len); |
| mutex_unlock(&priv->lock); |
| |
| if (status < 0) |
| return status; |
| *retlen = status; |
| return 0; |
| } |
| |
| static int dataflash_read_user_otp(struct mtd_info *mtd, |
| loff_t from, size_t len, size_t *retlen, u_char *buf) |
| { |
| struct dataflash *priv = mtd->priv; |
| int status; |
| |
| /* 64 bytes, from 0..63 ... start at 0 on-chip */ |
| mutex_lock(&priv->lock); |
| status = otp_read(priv->spi, 0, buf, from, len); |
| mutex_unlock(&priv->lock); |
| |
| if (status < 0) |
| return status; |
| *retlen = status; |
| return 0; |
| } |
| |
| static int dataflash_write_user_otp(struct mtd_info *mtd, |
| loff_t from, size_t len, size_t *retlen, const u_char *buf) |
| { |
| struct spi_message m; |
| const size_t l = 4 + 64; |
| u8 *scratch; |
| struct spi_transfer t; |
| struct dataflash *priv = mtd->priv; |
| int status; |
| |
| if (from >= 64) { |
| /* |
| * Attempting to write beyond the end of OTP memory, |
| * no data can be written. |
| */ |
| *retlen = 0; |
| return 0; |
| } |
| |
| /* Truncate the write to fit into OTP memory. */ |
| if ((from + len) > 64) |
| len = 64 - from; |
| |
| /* OUT: OP_WRITE_SECURITY, 3 zeroes, 64 data-or-zero bytes |
| * IN: ignore all |
| */ |
| scratch = kzalloc(l, GFP_KERNEL); |
| if (!scratch) |
| return -ENOMEM; |
| scratch[0] = OP_WRITE_SECURITY; |
| memcpy(scratch + 4 + from, buf, len); |
| |
| spi_message_init(&m); |
| |
| memset(&t, 0, sizeof t); |
| t.tx_buf = scratch; |
| t.len = l; |
| spi_message_add_tail(&t, &m); |
| |
| /* Write the OTP bits, if they've not yet been written. |
| * This modifies SRAM buffer1. |
| */ |
| mutex_lock(&priv->lock); |
| dataflash_waitready(priv->spi); |
| status = spi_sync(priv->spi, &m); |
| mutex_unlock(&priv->lock); |
| |
| kfree(scratch); |
| |
| if (status >= 0) { |
| status = 0; |
| *retlen = len; |
| } |
| return status; |
| } |
| |
| static char *otp_setup(struct mtd_info *device, char revision) |
| { |
| device->_get_fact_prot_info = dataflash_get_otp_info; |
| device->_read_fact_prot_reg = dataflash_read_fact_otp; |
| device->_get_user_prot_info = dataflash_get_otp_info; |
| device->_read_user_prot_reg = dataflash_read_user_otp; |
| |
| /* rev c parts (at45db321c and at45db1281 only!) use a |
| * different write procedure; not (yet?) implemented. |
| */ |
| if (revision > 'c') |
| device->_write_user_prot_reg = dataflash_write_user_otp; |
| |
| return ", OTP"; |
| } |
| |
| #else |
| |
| static char *otp_setup(struct mtd_info *device, char revision) |
| { |
| return " (OTP)"; |
| } |
| |
| #endif |
| |
| /* ......................................................................... */ |
| |
| /* |
| * Register DataFlash device with MTD subsystem. |
| */ |
| static int add_dataflash_otp(struct spi_device *spi, char *name, int nr_pages, |
| int pagesize, int pageoffset, char revision) |
| { |
| struct dataflash *priv; |
| struct mtd_info *device; |
| struct flash_platform_data *pdata = dev_get_platdata(&spi->dev); |
| char *otp_tag = ""; |
| int err = 0; |
| |
| priv = kzalloc(sizeof *priv, GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| mutex_init(&priv->lock); |
| priv->spi = spi; |
| priv->page_size = pagesize; |
| priv->page_offset = pageoffset; |
| |
| /* name must be usable with cmdlinepart */ |
| sprintf(priv->name, "spi%d.%d-%s", |
| spi->master->bus_num, spi->chip_select, |
| name); |
| |
| device = &priv->mtd; |
| device->name = (pdata && pdata->name) ? pdata->name : priv->name; |
| device->size = nr_pages * pagesize; |
| device->erasesize = pagesize; |
| device->writesize = pagesize; |
| device->type = MTD_DATAFLASH; |
| device->flags = MTD_WRITEABLE; |
| device->_erase = dataflash_erase; |
| device->_read = dataflash_read; |
| device->_write = dataflash_write; |
| device->priv = priv; |
| |
| device->dev.parent = &spi->dev; |
| mtd_set_of_node(device, spi->dev.of_node); |
| |
| if (revision >= 'c') |
| otp_tag = otp_setup(device, revision); |
| |
| dev_info(&spi->dev, "%s (%lld KBytes) pagesize %d bytes%s\n", |
| name, (long long)((device->size + 1023) >> 10), |
| pagesize, otp_tag); |
| spi_set_drvdata(spi, priv); |
| |
| err = mtd_device_register(device, |
| pdata ? pdata->parts : NULL, |
| pdata ? pdata->nr_parts : 0); |
| |
| if (!err) |
| return 0; |
| |
| kfree(priv); |
| return err; |
| } |
| |
| static inline int add_dataflash(struct spi_device *spi, char *name, |
| int nr_pages, int pagesize, int pageoffset) |
| { |
| return add_dataflash_otp(spi, name, nr_pages, pagesize, |
| pageoffset, 0); |
| } |
| |
| struct flash_info { |
| char *name; |
| |
| /* JEDEC id has a high byte of zero plus three data bytes: |
| * the manufacturer id, then a two byte device id. |
| */ |
| u64 jedec_id; |
| |
| /* The size listed here is what works with OP_ERASE_PAGE. */ |
| unsigned nr_pages; |
| u16 pagesize; |
| u16 pageoffset; |
| |
| u16 flags; |
| #define SUP_EXTID 0x0004 /* supports extended ID data */ |
| #define SUP_POW2PS 0x0002 /* supports 2^N byte pages */ |
| #define IS_POW2PS 0x0001 /* uses 2^N byte pages */ |
| }; |
| |
| static struct flash_info dataflash_data[] = { |
| |
| /* |
| * NOTE: chips with SUP_POW2PS (rev D and up) need two entries, |
| * one with IS_POW2PS and the other without. The entry with the |
| * non-2^N byte page size can't name exact chip revisions without |
| * losing backwards compatibility for cmdlinepart. |
| * |
| * These newer chips also support 128-byte security registers (with |
| * 64 bytes one-time-programmable) and software write-protection. |
| */ |
| { "AT45DB011B", 0x1f2200, 512, 264, 9, SUP_POW2PS}, |
| { "at45db011d", 0x1f2200, 512, 256, 8, SUP_POW2PS | IS_POW2PS}, |
| |
| { "AT45DB021B", 0x1f2300, 1024, 264, 9, SUP_POW2PS}, |
| { "at45db021d", 0x1f2300, 1024, 256, 8, SUP_POW2PS | IS_POW2PS}, |
| |
| { "AT45DB041x", 0x1f2400, 2048, 264, 9, SUP_POW2PS}, |
| { "at45db041d", 0x1f2400, 2048, 256, 8, SUP_POW2PS | IS_POW2PS}, |
| |
| { "AT45DB081B", 0x1f2500, 4096, 264, 9, SUP_POW2PS}, |
| { "at45db081d", 0x1f2500, 4096, 256, 8, SUP_POW2PS | IS_POW2PS}, |
| |
| { "AT45DB161x", 0x1f2600, 4096, 528, 10, SUP_POW2PS}, |
| { "at45db161d", 0x1f2600, 4096, 512, 9, SUP_POW2PS | IS_POW2PS}, |
| |
| { "AT45DB321x", 0x1f2700, 8192, 528, 10, 0}, /* rev C */ |
| |
| { "AT45DB321x", 0x1f2701, 8192, 528, 10, SUP_POW2PS}, |
| { "at45db321d", 0x1f2701, 8192, 512, 9, SUP_POW2PS | IS_POW2PS}, |
| |
| { "AT45DB642x", 0x1f2800, 8192, 1056, 11, SUP_POW2PS}, |
| { "at45db642d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS}, |
| |
| { "AT45DB641E", 0x1f28000100ULL, 32768, 264, 9, SUP_EXTID | SUP_POW2PS}, |
| { "at45db641e", 0x1f28000100ULL, 32768, 256, 8, SUP_EXTID | SUP_POW2PS | IS_POW2PS}, |
| }; |
| |
| static struct flash_info *jedec_lookup(struct spi_device *spi, |
| u64 jedec, bool use_extid) |
| { |
| struct flash_info *info; |
| int status; |
| |
| for (info = dataflash_data; |
| info < dataflash_data + ARRAY_SIZE(dataflash_data); |
| info++) { |
| if (use_extid && !(info->flags & SUP_EXTID)) |
| continue; |
| |
| if (info->jedec_id == jedec) { |
| dev_dbg(&spi->dev, "OTP, sector protect%s\n", |
| (info->flags & SUP_POW2PS) ? |
| ", binary pagesize" : ""); |
| if (info->flags & SUP_POW2PS) { |
| status = dataflash_status(spi); |
| if (status < 0) { |
| dev_dbg(&spi->dev, "status error %d\n", |
| status); |
| return ERR_PTR(status); |
| } |
| if (status & 0x1) { |
| if (info->flags & IS_POW2PS) |
| return info; |
| } else { |
| if (!(info->flags & IS_POW2PS)) |
| return info; |
| } |
| } else |
| return info; |
| } |
| } |
| |
| return ERR_PTR(-ENODEV); |
| } |
| |
| static struct flash_info *jedec_probe(struct spi_device *spi) |
| { |
| int ret; |
| u8 code = OP_READ_ID; |
| u64 jedec; |
| u8 id[sizeof(jedec)] = {0}; |
| const unsigned int id_size = 5; |
| struct flash_info *info; |
| |
| /* |
| * JEDEC also defines an optional "extended device information" |
| * string for after vendor-specific data, after the three bytes |
| * we use here. Supporting some chips might require using it. |
| * |
| * If the vendor ID isn't Atmel's (0x1f), assume this call failed. |
| * That's not an error; only rev C and newer chips handle it, and |
| * only Atmel sells these chips. |
| */ |
| ret = spi_write_then_read(spi, &code, 1, id, id_size); |
| if (ret < 0) { |
| dev_dbg(&spi->dev, "error %d reading JEDEC ID\n", ret); |
| return ERR_PTR(ret); |
| } |
| |
| if (id[0] != CFI_MFR_ATMEL) |
| return NULL; |
| |
| jedec = be64_to_cpup((__be64 *)id); |
| |
| /* |
| * First, try to match device using extended device |
| * information |
| */ |
| info = jedec_lookup(spi, jedec >> DATAFLASH_SHIFT_EXTID, true); |
| if (!IS_ERR(info)) |
| return info; |
| /* |
| * If that fails, make another pass using regular ID |
| * information |
| */ |
| info = jedec_lookup(spi, jedec >> DATAFLASH_SHIFT_ID, false); |
| if (!IS_ERR(info)) |
| return info; |
| /* |
| * Treat other chips as errors ... we won't know the right page |
| * size (it might be binary) even when we can tell which density |
| * class is involved (legacy chip id scheme). |
| */ |
| dev_warn(&spi->dev, "JEDEC id %016llx not handled\n", jedec); |
| return ERR_PTR(-ENODEV); |
| } |
| |
| /* |
| * Detect and initialize DataFlash device, using JEDEC IDs on newer chips |
| * or else the ID code embedded in the status bits: |
| * |
| * Device Density ID code #Pages PageSize Offset |
| * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9 |
| * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1024 264 9 |
| * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9 |
| * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9 |
| * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10 |
| * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10 |
| * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11 |
| * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11 |
| */ |
| static int dataflash_probe(struct spi_device *spi) |
| { |
| int status; |
| struct flash_info *info; |
| |
| /* |
| * Try to detect dataflash by JEDEC ID. |
| * If it succeeds we know we have either a C or D part. |
| * D will support power of 2 pagesize option. |
| * Both support the security register, though with different |
| * write procedures. |
| */ |
| info = jedec_probe(spi); |
| if (IS_ERR(info)) |
| return PTR_ERR(info); |
| if (info != NULL) |
| return add_dataflash_otp(spi, info->name, info->nr_pages, |
| info->pagesize, info->pageoffset, |
| (info->flags & SUP_POW2PS) ? 'd' : 'c'); |
| |
| /* |
| * Older chips support only legacy commands, identifing |
| * capacity using bits in the status byte. |
| */ |
| status = dataflash_status(spi); |
| if (status <= 0 || status == 0xff) { |
| dev_dbg(&spi->dev, "status error %d\n", status); |
| if (status == 0 || status == 0xff) |
| status = -ENODEV; |
| return status; |
| } |
| |
| /* if there's a device there, assume it's dataflash. |
| * board setup should have set spi->max_speed_max to |
| * match f(car) for continuous reads, mode 0 or 3. |
| */ |
| switch (status & 0x3c) { |
| case 0x0c: /* 0 0 1 1 x x */ |
| status = add_dataflash(spi, "AT45DB011B", 512, 264, 9); |
| break; |
| case 0x14: /* 0 1 0 1 x x */ |
| status = add_dataflash(spi, "AT45DB021B", 1024, 264, 9); |
| break; |
| case 0x1c: /* 0 1 1 1 x x */ |
| status = add_dataflash(spi, "AT45DB041x", 2048, 264, 9); |
| break; |
| case 0x24: /* 1 0 0 1 x x */ |
| status = add_dataflash(spi, "AT45DB081B", 4096, 264, 9); |
| break; |
| case 0x2c: /* 1 0 1 1 x x */ |
| status = add_dataflash(spi, "AT45DB161x", 4096, 528, 10); |
| break; |
| case 0x34: /* 1 1 0 1 x x */ |
| status = add_dataflash(spi, "AT45DB321x", 8192, 528, 10); |
| break; |
| case 0x38: /* 1 1 1 x x x */ |
| case 0x3c: |
| status = add_dataflash(spi, "AT45DB642x", 8192, 1056, 11); |
| break; |
| /* obsolete AT45DB1282 not (yet?) supported */ |
| default: |
| dev_info(&spi->dev, "unsupported device (%x)\n", |
| status & 0x3c); |
| status = -ENODEV; |
| } |
| |
| if (status < 0) |
| dev_dbg(&spi->dev, "add_dataflash --> %d\n", status); |
| |
| return status; |
| } |
| |
| static void dataflash_remove(struct spi_device *spi) |
| { |
| struct dataflash *flash = spi_get_drvdata(spi); |
| |
| dev_dbg(&spi->dev, "remove\n"); |
| |
| WARN_ON(mtd_device_unregister(&flash->mtd)); |
| |
| kfree(flash); |
| } |
| |
| static struct spi_driver dataflash_driver = { |
| .driver = { |
| .name = "mtd_dataflash", |
| .of_match_table = of_match_ptr(dataflash_dt_ids), |
| }, |
| .probe = dataflash_probe, |
| .remove = dataflash_remove, |
| .id_table = dataflash_spi_ids, |
| |
| /* FIXME: investigate suspend and resume... */ |
| }; |
| |
| module_spi_driver(dataflash_driver); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_AUTHOR("Andrew Victor, David Brownell"); |
| MODULE_DESCRIPTION("MTD DataFlash driver"); |
| MODULE_ALIAS("spi:mtd_dataflash"); |