blob: 835b53302db803817e4d37a03ae3b149ee4e895c [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
%YAML 1.2
---
$id: http://devicetree.org/schemas/regulator/nxp,pca9450-regulator.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: NXP PCA9450A/B/C Power Management Integrated Circuit regulators
maintainers:
- Robin Gong <yibin.gong@nxp.com>
description: |
Regulator nodes should be named to BUCK_<number> and LDO_<number>. The
definition for each of these nodes is defined using the standard
binding for regulators at
Documentation/devicetree/bindings/regulator/regulator.txt.
Datasheet is available at
https://www.nxp.com/docs/en/data-sheet/PCA9450DS.pdf
#The valid names for PCA9450 regulator nodes are:
#BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6,
#LDO1, LDO2, LDO3, LDO4, LDO5
#Note: Buck3 removed on PCA9450B and connect with Buck1 on PCA9450C.
properties:
compatible:
enum:
- nxp,pca9450a
- nxp,pca9450b
- nxp,pca9450c
reg:
maxItems: 1
interrupts:
maxItems: 1
regulators:
type: object
description: |
list of regulators provided by this controller
patternProperties:
"^LDO[1-5]$":
type: object
$ref: regulator.yaml#
description:
Properties for single LDO regulator.
unevaluatedProperties: false
"^BUCK[1-6]$":
type: object
$ref: regulator.yaml#
description:
Properties for single BUCK regulator.
properties:
nxp,dvs-run-voltage:
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 600000
maximum: 2187500
description:
PMIC default "RUN" state voltage in uV. Only Buck1~3 have such
dvs(dynamic voltage scaling) property.
nxp,dvs-standby-voltage:
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 600000
maximum: 2187500
description:
PMIC default "STANDBY" state voltage in uV. Only Buck1~3 have such
dvs(dynamic voltage scaling) property.
unevaluatedProperties: false
additionalProperties: false
sd-vsel-gpios:
description: GPIO that is used to switch LDO5 between being configured by
LDO5CTRL_L or LDO5CTRL_H register. Use this if the SD_VSEL signal is
connected to a host GPIO.
nxp,i2c-lt-enable:
type: boolean
description:
Indicates that the I2C Level Translator is used.
nxp,wdog_b-warm-reset:
type: boolean
description:
When WDOG_B signal is asserted a warm reset will be done instead of cold
reset.
required:
- compatible
- reg
- interrupts
- regulators
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/irq.h>
i2c {
#address-cells = <1>;
#size-cells = <0>;
pmic: pmic@25 {
compatible = "nxp,pca9450b";
reg = <0x25>;
pinctrl-0 = <&pinctrl_pmic>;
interrupt-parent = <&gpio1>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
regulators {
buck1: BUCK1 {
regulator-name = "BUCK1";
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <2187500>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <3125>;
};
buck2: BUCK2 {
regulator-name = "BUCK2";
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <2187500>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <3125>;
nxp,dvs-run-voltage = <950000>;
nxp,dvs-standby-voltage = <850000>;
};
buck4: BUCK4 {
regulator-name = "BUCK4";
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <3400000>;
regulator-boot-on;
regulator-always-on;
};
buck5: BUCK5 {
regulator-name = "BUCK5";
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <3400000>;
regulator-boot-on;
regulator-always-on;
};
buck6: BUCK6 {
regulator-name = "BUCK6";
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <3400000>;
regulator-boot-on;
regulator-always-on;
};
ldo1: LDO1 {
regulator-name = "LDO1";
regulator-min-microvolt = <1600000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
ldo2: LDO2 {
regulator-name = "LDO2";
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1150000>;
regulator-boot-on;
regulator-always-on;
};
ldo3: LDO3 {
regulator-name = "LDO3";
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
ldo4: LDO4 {
regulator-name = "LDO4";
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
ldo5: LDO5 {
regulator-name = "LDO5";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
};
};
};