| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Copyright 2012 Linaro Ltd |
| */ |
| |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/mfd/dbx500-prcmu.h> |
| #include <dt-bindings/arm/ux500_pm_domains.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| /* This stablilizes the device enumeration */ |
| aliases { |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; |
| i2c3 = &i2c3; |
| i2c4 = &i2c4; |
| spi0 = &spi0; |
| spi1 = &spi1; |
| spi2 = &spi2; |
| spi3 = &spi3; |
| serial0 = &serial0; |
| serial1 = &serial1; |
| serial2 = &serial2; |
| }; |
| |
| chosen { |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| enable-method = "ste,dbx500-smp"; |
| |
| cpu-map { |
| cluster0 { |
| core0 { |
| cpu = <&CPU0>; |
| }; |
| core1 { |
| cpu = <&CPU1>; |
| }; |
| }; |
| }; |
| CPU0: cpu@300 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| reg = <0x300>; |
| clocks = <&prcmu_clk PRCMU_ARMSS>; |
| clock-names = "cpu"; |
| clock-latency = <20000>; |
| #cooling-cells = <2>; |
| }; |
| CPU1: cpu@301 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| reg = <0x301>; |
| }; |
| }; |
| |
| thermal-zones { |
| /* |
| * Thermal zone for the SoC, using the thermal sensor in the |
| * PRCMU for temperature and the cpufreq driver for passive |
| * cooling. |
| */ |
| cpu_thermal: cpu-thermal { |
| polling-delay-passive = <250>; |
| /* |
| * This sensor fires interrupts to update the thermal |
| * zone, so no polling is needed. |
| */ |
| polling-delay = <0>; |
| |
| thermal-sensors = <&thermal>; |
| |
| trips { |
| cpu_alert: cpu-alert { |
| temperature = <70000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu-crit { |
| temperature = <85000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| trip = <&cpu_alert>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| contribution = <100>; |
| }; |
| }; |
| }; |
| |
| soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "stericsson,db8500", "simple-bus"; |
| interrupt-parent = <&intc>; |
| ranges; |
| |
| ptm@801ae000 { |
| compatible = "arm,coresight-etm3x", "arm,primecell"; |
| reg = <0x801ae000 0x1000>; |
| |
| clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>; |
| clock-names = "apb_pclk", "atclk"; |
| cpu = <&CPU0>; |
| out-ports { |
| port { |
| ptm0_out_port: endpoint { |
| remote-endpoint = <&funnel_in_port0>; |
| }; |
| }; |
| }; |
| }; |
| |
| ptm@801af000 { |
| compatible = "arm,coresight-etm3x", "arm,primecell"; |
| reg = <0x801af000 0x1000>; |
| |
| clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>; |
| clock-names = "apb_pclk", "atclk"; |
| cpu = <&CPU1>; |
| out-ports { |
| port { |
| ptm1_out_port: endpoint { |
| remote-endpoint = <&funnel_in_port1>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@801a6000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0x801a6000 0x1000>; |
| |
| clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>; |
| clock-names = "apb_pclk", "atclk"; |
| out-ports { |
| port { |
| funnel_out_port: endpoint { |
| remote-endpoint = |
| <&replicator_in_port0>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| funnel_in_port0: endpoint { |
| remote-endpoint = <&ptm0_out_port>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| funnel_in_port1: endpoint { |
| remote-endpoint = <&ptm1_out_port>; |
| }; |
| }; |
| }; |
| }; |
| |
| replicator { |
| compatible = "arm,coresight-static-replicator"; |
| clocks = <&prcmu_clk PRCMU_APEATCLK>; |
| clock-names = "atclk"; |
| |
| out-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| replicator_out_port0: endpoint { |
| remote-endpoint = <&tpiu_in_port>; |
| }; |
| }; |
| port@1 { |
| reg = <1>; |
| replicator_out_port1: endpoint { |
| remote-endpoint = <&etb_in_port>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| port { |
| replicator_in_port0: endpoint { |
| remote-endpoint = <&funnel_out_port>; |
| }; |
| }; |
| }; |
| }; |
| |
| tpiu@80190000 { |
| compatible = "arm,coresight-tpiu", "arm,primecell"; |
| reg = <0x80190000 0x1000>; |
| |
| clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>; |
| clock-names = "apb_pclk", "atclk"; |
| in-ports { |
| port { |
| tpiu_in_port: endpoint { |
| remote-endpoint = <&replicator_out_port0>; |
| }; |
| }; |
| }; |
| }; |
| |
| etb@801a4000 { |
| compatible = "arm,coresight-etb10", "arm,primecell"; |
| reg = <0x801a4000 0x1000>; |
| |
| clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>; |
| clock-names = "apb_pclk", "atclk"; |
| in-ports { |
| port { |
| etb_in_port: endpoint { |
| remote-endpoint = <&replicator_out_port1>; |
| }; |
| }; |
| }; |
| }; |
| |
| intc: interrupt-controller@a0411000 { |
| compatible = "arm,cortex-a9-gic"; |
| #interrupt-cells = <3>; |
| #address-cells = <1>; |
| interrupt-controller; |
| reg = <0xa0411000 0x1000>, |
| <0xa0410100 0x100>; |
| }; |
| |
| scu@a0410000 { |
| compatible = "arm,cortex-a9-scu"; |
| reg = <0xa0410000 0x100>; |
| }; |
| |
| /* |
| * The backup RAM is used for retention during sleep |
| * and various things like spin tables |
| */ |
| backupram@80150000 { |
| compatible = "ste,dbx500-backupram"; |
| reg = <0x80150000 0x2000>; |
| }; |
| |
| L2: l2-cache { |
| compatible = "arm,pl310-cache"; |
| reg = <0xa0412000 0x1000>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| cache-unified; |
| cache-level = <2>; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a9-pmu"; |
| interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| pm_domains: pm_domains0 { |
| compatible = "stericsson,ux500-pm-domains"; |
| #power-domain-cells = <1>; |
| }; |
| |
| clocks { |
| compatible = "stericsson,u8500-clks"; |
| /* |
| * Registers for the CLKRST block on peripheral |
| * groups 1, 2, 3, 5, 6, |
| */ |
| reg = <0x8012f000 0x1000>, <0x8011f000 0x1000>, |
| <0x8000f000 0x1000>, <0xa03ff000 0x1000>, |
| <0xa03cf000 0x1000>; |
| |
| prcmu_clk: prcmu-clock { |
| #clock-cells = <1>; |
| }; |
| |
| prcc_pclk: prcc-periph-clock { |
| #clock-cells = <2>; |
| }; |
| |
| prcc_kclk: prcc-kernel-clock { |
| #clock-cells = <2>; |
| }; |
| |
| rtc_clk: rtc32k-clock { |
| #clock-cells = <0>; |
| }; |
| |
| smp_twd_clk: smp-twd-clock { |
| #clock-cells = <0>; |
| }; |
| }; |
| |
| mtu@a03c6000 { |
| /* Nomadik System Timer */ |
| compatible = "st,nomadik-mtu"; |
| reg = <0xa03c6000 0x1000>; |
| interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&prcmu_clk PRCMU_TIMCLK>, <&prcc_pclk 6 6>; |
| clock-names = "timclk", "apb_pclk"; |
| }; |
| |
| timer@a0410600 { |
| compatible = "arm,cortex-a9-twd-timer"; |
| reg = <0xa0410600 0x20>; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>; |
| |
| clocks = <&smp_twd_clk>; |
| }; |
| |
| watchdog@a0410620 { |
| compatible = "arm,cortex-a9-twd-wdt"; |
| reg = <0xa0410620 0x20>; |
| interrupts = <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>; |
| clocks = <&smp_twd_clk>; |
| }; |
| |
| rtc@80154000 { |
| compatible = "arm,pl031", "arm,primecell"; |
| reg = <0x80154000 0x1000>; |
| interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&rtc_clk>; |
| clock-names = "apb_pclk"; |
| }; |
| |
| gpio0: gpio@8012e000 { |
| compatible = "stericsson,db8500-gpio", |
| "st,nomadik-gpio"; |
| reg = <0x8012e000 0x80>; |
| interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| st,supports-sleepmode; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-bank = <0>; |
| gpio-ranges = <&pinctrl 0 0 32>; |
| clocks = <&prcc_pclk 1 9>; |
| }; |
| |
| gpio1: gpio@8012e080 { |
| compatible = "stericsson,db8500-gpio", |
| "st,nomadik-gpio"; |
| reg = <0x8012e080 0x80>; |
| interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| st,supports-sleepmode; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-bank = <1>; |
| gpio-ranges = <&pinctrl 0 32 5>; |
| clocks = <&prcc_pclk 1 9>; |
| }; |
| |
| gpio2: gpio@8000e000 { |
| compatible = "stericsson,db8500-gpio", |
| "st,nomadik-gpio"; |
| reg = <0x8000e000 0x80>; |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| st,supports-sleepmode; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-bank = <2>; |
| gpio-ranges = <&pinctrl 0 64 32>; |
| clocks = <&prcc_pclk 3 8>; |
| }; |
| |
| gpio3: gpio@8000e080 { |
| compatible = "stericsson,db8500-gpio", |
| "st,nomadik-gpio"; |
| reg = <0x8000e080 0x80>; |
| interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| st,supports-sleepmode; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-bank = <3>; |
| gpio-ranges = <&pinctrl 0 96 2>; |
| clocks = <&prcc_pclk 3 8>; |
| }; |
| |
| gpio4: gpio@8000e100 { |
| compatible = "stericsson,db8500-gpio", |
| "st,nomadik-gpio"; |
| reg = <0x8000e100 0x80>; |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| st,supports-sleepmode; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-bank = <4>; |
| gpio-ranges = <&pinctrl 0 128 32>; |
| clocks = <&prcc_pclk 3 8>; |
| }; |
| |
| gpio5: gpio@8000e180 { |
| compatible = "stericsson,db8500-gpio", |
| "st,nomadik-gpio"; |
| reg = <0x8000e180 0x80>; |
| interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| st,supports-sleepmode; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-bank = <5>; |
| gpio-ranges = <&pinctrl 0 160 12>; |
| clocks = <&prcc_pclk 3 8>; |
| }; |
| |
| gpio6: gpio@8011e000 { |
| compatible = "stericsson,db8500-gpio", |
| "st,nomadik-gpio"; |
| reg = <0x8011e000 0x80>; |
| interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| st,supports-sleepmode; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-bank = <6>; |
| gpio-ranges = <&pinctrl 0 192 32>; |
| clocks = <&prcc_pclk 2 11>; |
| }; |
| |
| gpio7: gpio@8011e080 { |
| compatible = "stericsson,db8500-gpio", |
| "st,nomadik-gpio"; |
| reg = <0x8011e080 0x80>; |
| interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| st,supports-sleepmode; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-bank = <7>; |
| gpio-ranges = <&pinctrl 0 224 7>; |
| clocks = <&prcc_pclk 2 11>; |
| }; |
| |
| gpio8: gpio@a03fe000 { |
| compatible = "stericsson,db8500-gpio", |
| "st,nomadik-gpio"; |
| reg = <0xa03fe000 0x80>; |
| interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| st,supports-sleepmode; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-bank = <8>; |
| gpio-ranges = <&pinctrl 0 256 12>; |
| clocks = <&prcc_pclk 5 1>; |
| }; |
| |
| pinctrl: pinctrl { |
| compatible = "stericsson,db8500-pinctrl"; |
| nomadik-gpio-chips = <&gpio0>, <&gpio1>, <&gpio2>, <&gpio3>, |
| <&gpio4>, <&gpio5>, <&gpio6>, <&gpio7>, |
| <&gpio8>; |
| prcm = <&prcmu>; |
| }; |
| |
| usb_per5@a03e0000 { |
| compatible = "stericsson,db8500-musb"; |
| reg = <0xa03e0000 0x10000>; |
| interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "mc"; |
| |
| dr_mode = "otg"; |
| |
| dmas = <&dma 38 0 0x2>, /* Logical - DevToMem */ |
| <&dma 38 0 0x0>, /* Logical - MemToDev */ |
| <&dma 37 0 0x2>, /* Logical - DevToMem */ |
| <&dma 37 0 0x0>, /* Logical - MemToDev */ |
| <&dma 36 0 0x2>, /* Logical - DevToMem */ |
| <&dma 36 0 0x0>, /* Logical - MemToDev */ |
| <&dma 19 0 0x2>, /* Logical - DevToMem */ |
| <&dma 19 0 0x0>, /* Logical - MemToDev */ |
| <&dma 18 0 0x2>, /* Logical - DevToMem */ |
| <&dma 18 0 0x0>, /* Logical - MemToDev */ |
| <&dma 17 0 0x2>, /* Logical - DevToMem */ |
| <&dma 17 0 0x0>, /* Logical - MemToDev */ |
| <&dma 16 0 0x2>, /* Logical - DevToMem */ |
| <&dma 16 0 0x0>, /* Logical - MemToDev */ |
| <&dma 39 0 0x2>, /* Logical - DevToMem */ |
| <&dma 39 0 0x0>; /* Logical - MemToDev */ |
| |
| dma-names = "iep_1_9", "oep_1_9", |
| "iep_2_10", "oep_2_10", |
| "iep_3_11", "oep_3_11", |
| "iep_4_12", "oep_4_12", |
| "iep_5_13", "oep_5_13", |
| "iep_6_14", "oep_6_14", |
| "iep_7_15", "oep_7_15", |
| "iep_8", "oep_8"; |
| |
| clocks = <&prcc_pclk 5 0>; |
| }; |
| |
| dma: dma-controller@801C0000 { |
| compatible = "stericsson,db8500-dma40", "stericsson,dma40"; |
| reg = <0x801C0000 0x1000 0x40010000 0x800>; |
| reg-names = "base", "lcpa"; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| |
| #dma-cells = <3>; |
| memcpy-channels = <56 57 58 59 60>; |
| |
| clocks = <&prcmu_clk PRCMU_DMACLK>; |
| }; |
| |
| prcmu: prcmu@80157000 { |
| compatible = "stericsson,db8500-prcmu", "syscon"; |
| reg = <0x80157000 0x2000>, <0x801b0000 0x8000>, <0x801b8000 0x1000>; |
| reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm"; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| ranges; |
| |
| prcmu-timer-4@80157450 { |
| compatible = "stericsson,db8500-prcmu-timer-4"; |
| reg = <0x80157450 0xC>; |
| }; |
| |
| thermal: thermal@801573c0 { |
| compatible = "stericsson,db8500-thermal"; |
| reg = <0x801573c0 0x40>; |
| interrupt-parent = <&prcmu>; |
| interrupts = <21 IRQ_TYPE_LEVEL_HIGH>, |
| <22 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "IRQ_HOTMON_LOW", "IRQ_HOTMON_HIGH"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| db8500-prcmu-regulators { |
| compatible = "stericsson,db8500-prcmu-regulator"; |
| |
| // DB8500_REGULATOR_VAPE |
| db8500_vape_reg: db8500_vape { |
| regulator-always-on; |
| }; |
| |
| // DB8500_REGULATOR_VARM |
| db8500_varm_reg: db8500_varm { |
| }; |
| |
| // DB8500_REGULATOR_VMODEM |
| db8500_vmodem_reg: db8500_vmodem { |
| }; |
| |
| // DB8500_REGULATOR_VPLL |
| db8500_vpll_reg: db8500_vpll { |
| }; |
| |
| // DB8500_REGULATOR_VSMPS1 |
| db8500_vsmps1_reg: db8500_vsmps1 { |
| }; |
| |
| // DB8500_REGULATOR_VSMPS2 |
| db8500_vsmps2_reg: db8500_vsmps2 { |
| }; |
| |
| // DB8500_REGULATOR_VSMPS3 |
| db8500_vsmps3_reg: db8500_vsmps3 { |
| }; |
| |
| // DB8500_REGULATOR_VRF1 |
| db8500_vrf1_reg: db8500_vrf1 { |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_SVAMMDSP |
| db8500_sva_mmdsp_reg: db8500_sva_mmdsp { |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_SVAMMDSPRET |
| db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret { |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_SVAPIPE |
| db8500_sva_pipe_reg: db8500_sva_pipe { |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_SIAMMDSP |
| db8500_sia_mmdsp_reg: db8500_sia_mmdsp { |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_SIAMMDSPRET |
| db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret { |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_SIAPIPE |
| db8500_sia_pipe_reg: db8500_sia_pipe { |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_SGA |
| db8500_sga_reg: db8500_sga { |
| vin-supply = <&db8500_vape_reg>; |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_B2R2_MCDE |
| db8500_b2r2_mcde_reg: db8500_b2r2_mcde { |
| vin-supply = <&db8500_vape_reg>; |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_ESRAM12 |
| db8500_esram12_reg: db8500_esram12 { |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_ESRAM12RET |
| db8500_esram12_ret_reg: db8500_esram12_ret { |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_ESRAM34 |
| db8500_esram34_reg: db8500_esram34 { |
| }; |
| |
| // DB8500_REGULATOR_SWITCH_ESRAM34RET |
| db8500_esram34_ret_reg: db8500_esram34_ret { |
| }; |
| }; |
| }; |
| |
| i2c0: i2c@80004000 { |
| compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell"; |
| reg = <0x80004000 0x1000>; |
| interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| v-i2c-supply = <&db8500_vape_reg>; |
| |
| clock-frequency = <400000>; |
| clocks = <&prcc_kclk 3 3>, <&prcc_pclk 3 3>; |
| clock-names = "i2cclk", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@80122000 { |
| compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell"; |
| reg = <0x80122000 0x1000>; |
| interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| v-i2c-supply = <&db8500_vape_reg>; |
| |
| clock-frequency = <400000>; |
| |
| clocks = <&prcc_kclk 1 2>, <&prcc_pclk 1 2>; |
| clock-names = "i2cclk", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@80128000 { |
| compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell"; |
| reg = <0x80128000 0x1000>; |
| interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| v-i2c-supply = <&db8500_vape_reg>; |
| |
| clock-frequency = <400000>; |
| |
| clocks = <&prcc_kclk 1 6>, <&prcc_pclk 1 6>; |
| clock-names = "i2cclk", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@80110000 { |
| compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell"; |
| reg = <0x80110000 0x1000>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| v-i2c-supply = <&db8500_vape_reg>; |
| |
| clock-frequency = <400000>; |
| |
| clocks = <&prcc_kclk 2 0>, <&prcc_pclk 2 0>; |
| clock-names = "i2cclk", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@8012a000 { |
| compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell"; |
| reg = <0x8012a000 0x1000>; |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| v-i2c-supply = <&db8500_vape_reg>; |
| |
| clock-frequency = <400000>; |
| |
| clocks = <&prcc_kclk 1 9>, <&prcc_pclk 1 10>; |
| clock-names = "i2cclk", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| ssp0: spi@80002000 { |
| compatible = "arm,pl022", "arm,primecell"; |
| reg = <0x80002000 0x1000>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&prcc_kclk 3 1>, <&prcc_pclk 3 1>; |
| clock-names = "SSPCLK", "apb_pclk"; |
| dmas = <&dma 8 0 0x2>, /* Logical - DevToMem */ |
| <&dma 8 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| ssp1: spi@80003000 { |
| compatible = "arm,pl022", "arm,primecell"; |
| reg = <0x80003000 0x1000>; |
| interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&prcc_kclk 3 2>, <&prcc_pclk 3 2>; |
| clock-names = "SSPCLK", "apb_pclk"; |
| dmas = <&dma 9 0 0x2>, /* Logical - DevToMem */ |
| <&dma 9 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| spi0: spi@8011a000 { |
| compatible = "arm,pl022", "arm,primecell"; |
| reg = <0x8011a000 0x1000>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| /* Same clock wired to kernel and pclk */ |
| clocks = <&prcc_pclk 2 8>, <&prcc_pclk 2 8>; |
| clock-names = "SSPCLK", "apb_pclk"; |
| dmas = <&dma 0 0 0x2>, /* Logical - DevToMem */ |
| <&dma 0 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| spi1: spi@80112000 { |
| compatible = "arm,pl022", "arm,primecell"; |
| reg = <0x80112000 0x1000>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| /* Same clock wired to kernel and pclk */ |
| clocks = <&prcc_pclk 2 2>, <&prcc_pclk 2 2>; |
| clock-names = "SSPCLK", "apb_pclk"; |
| dmas = <&dma 35 0 0x2>, /* Logical - DevToMem */ |
| <&dma 35 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| spi2: spi@80111000 { |
| compatible = "arm,pl022", "arm,primecell"; |
| reg = <0x80111000 0x1000>; |
| interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| /* Same clock wired to kernel and pclk */ |
| clocks = <&prcc_pclk 2 1>, <&prcc_pclk 2 1>; |
| clock-names = "SSPCLK", "apb_pclk"; |
| dmas = <&dma 33 0 0x2>, /* Logical - DevToMem */ |
| <&dma 33 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| spi3: spi@80129000 { |
| compatible = "arm,pl022", "arm,primecell"; |
| reg = <0x80129000 0x1000>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| /* Same clock wired to kernel and pclk */ |
| clocks = <&prcc_pclk 1 7>, <&prcc_pclk 1 7>; |
| clock-names = "SSPCLK", "apb_pclk"; |
| dmas = <&dma 40 0 0x2>, /* Logical - DevToMem */ |
| <&dma 40 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| serial0: uart@80120000 { |
| compatible = "arm,pl011", "arm,primecell"; |
| reg = <0x80120000 0x1000>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */ |
| <&dma 13 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 1 0>, <&prcc_pclk 1 0>; |
| clock-names = "uart", "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| serial1: uart@80121000 { |
| compatible = "arm,pl011", "arm,primecell"; |
| reg = <0x80121000 0x1000>; |
| interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dmas = <&dma 12 0 0x2>, /* Logical - DevToMem */ |
| <&dma 12 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 1 1>, <&prcc_pclk 1 1>; |
| clock-names = "uart", "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| serial2: uart@80007000 { |
| compatible = "arm,pl011", "arm,primecell"; |
| reg = <0x80007000 0x1000>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dmas = <&dma 11 0 0x2>, /* Logical - DevToMem */ |
| <&dma 11 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 3 6>, <&prcc_pclk 3 6>; |
| clock-names = "uart", "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| sdi0_per1@80126000 { |
| compatible = "arm,pl18x", "arm,primecell"; |
| reg = <0x80126000 0x1000>; |
| interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dmas = <&dma 29 0 0x2>, /* Logical - DevToMem */ |
| <&dma 29 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>; |
| clock-names = "sdi", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| sdi1_per2@80118000 { |
| compatible = "arm,pl18x", "arm,primecell"; |
| reg = <0x80118000 0x1000>; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dmas = <&dma 32 0 0x2>, /* Logical - DevToMem */ |
| <&dma 32 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 2 4>, <&prcc_pclk 2 6>; |
| clock-names = "sdi", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| sdi2_per3@80005000 { |
| compatible = "arm,pl18x", "arm,primecell"; |
| reg = <0x80005000 0x1000>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dmas = <&dma 28 0 0x2>, /* Logical - DevToMem */ |
| <&dma 28 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 3 4>, <&prcc_pclk 3 4>; |
| clock-names = "sdi", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| sdi3_per2@80119000 { |
| compatible = "arm,pl18x", "arm,primecell"; |
| reg = <0x80119000 0x1000>; |
| interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dmas = <&dma 41 0 0x2>, /* Logical - DevToMem */ |
| <&dma 41 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 2 5>, <&prcc_pclk 2 7>; |
| clock-names = "sdi", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| sdi4_per2@80114000 { |
| compatible = "arm,pl18x", "arm,primecell"; |
| reg = <0x80114000 0x1000>; |
| interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dmas = <&dma 42 0 0x2>, /* Logical - DevToMem */ |
| <&dma 42 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 2 2>, <&prcc_pclk 2 4>; |
| clock-names = "sdi", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| sdi5_per3@80008000 { |
| compatible = "arm,pl18x", "arm,primecell"; |
| reg = <0x80008000 0x1000>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dmas = <&dma 43 0 0x2>, /* Logical - DevToMem */ |
| <&dma 43 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 3 7>, <&prcc_pclk 3 7>; |
| clock-names = "sdi", "apb_pclk"; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| |
| status = "disabled"; |
| }; |
| |
| sound { |
| compatible = "stericsson,snd-soc-mop500"; |
| stericsson,cpu-dai = <&msp1 &msp3>; |
| }; |
| |
| msp0: msp@80123000 { |
| compatible = "stericsson,ux500-msp-i2s"; |
| reg = <0x80123000 0x1000>; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; |
| v-ape-supply = <&db8500_vape_reg>; |
| |
| dmas = <&dma 31 0 0x12>, /* Logical - DevToMem - HighPrio */ |
| <&dma 31 0 0x10>; /* Logical - MemToDev - HighPrio */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 1 3>, <&prcc_pclk 1 3>; |
| clock-names = "msp", "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| msp1: msp@80124000 { |
| compatible = "stericsson,ux500-msp-i2s"; |
| reg = <0x80124000 0x1000>; |
| interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; |
| v-ape-supply = <&db8500_vape_reg>; |
| |
| /* This DMA channel only exist on DB8500 v1 */ |
| dmas = <&dma 30 0 0x10>; /* Logical - MemToDev - HighPrio */ |
| dma-names = "tx"; |
| |
| clocks = <&prcc_kclk 1 4>, <&prcc_pclk 1 4>; |
| clock-names = "msp", "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| // HDMI sound |
| msp2: msp@80117000 { |
| compatible = "stericsson,ux500-msp-i2s"; |
| reg = <0x80117000 0x1000>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| v-ape-supply = <&db8500_vape_reg>; |
| |
| dmas = <&dma 14 0 0x12>, /* Logical - DevToMem - HighPrio */ |
| <&dma 14 1 0x19>; /* Physical Chan 1 - MemToDev |
| HighPrio - Fixed */ |
| dma-names = "rx", "tx"; |
| |
| clocks = <&prcc_kclk 2 3>, <&prcc_pclk 2 5>; |
| clock-names = "msp", "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| msp3: msp@80125000 { |
| compatible = "stericsson,ux500-msp-i2s"; |
| reg = <0x80125000 0x1000>; |
| interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; |
| v-ape-supply = <&db8500_vape_reg>; |
| |
| /* This DMA channel only exist on DB8500 v2 */ |
| dmas = <&dma 30 0 0x12>; /* Logical - DevToMem - HighPrio */ |
| dma-names = "rx"; |
| |
| clocks = <&prcc_kclk 1 10>, <&prcc_pclk 1 11>; |
| clock-names = "msp", "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| external-bus@50000000 { |
| compatible = "simple-bus"; |
| reg = <0x50000000 0x4000000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x50000000 0x4000000>; |
| status = "disabled"; |
| }; |
| |
| gpu@a0300000 { |
| /* |
| * This block is referred to as "Smart Graphics Adapter SGA500" |
| * in documentation but is in practice a pretty straight-forward |
| * MALI-400 GPU block. |
| */ |
| compatible = "stericsson,db8500-mali", "arm,mali-400"; |
| reg = <0xa0300000 0x10000>; |
| interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "gp", |
| "gpmmu", |
| "pp0", |
| "ppmmu0", |
| "combined"; |
| clocks = <&prcmu_clk PRCMU_ACLK>, <&prcmu_clk PRCMU_SGACLK>; |
| clock-names = "bus", "core"; |
| mali-supply = <&db8500_sga_reg>; |
| power-domains = <&pm_domains DOMAIN_VAPE>; |
| }; |
| |
| mcde@a0350000 { |
| compatible = "ste,mcde"; |
| reg = <0xa0350000 0x1000>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| epod-supply = <&db8500_b2r2_mcde_reg>; |
| clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */ |
| <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */ |
| <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */ |
| clock-names = "mcde", "lcd", "hdmi"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| status = "disabled"; |
| |
| dsi0: dsi-controller@a0351000 { |
| compatible = "ste,mcde-dsi"; |
| reg = <0xa0351000 0x1000>; |
| clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>; |
| clock-names = "hs", "lp"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| dsi1: dsi-controller@a0352000 { |
| compatible = "ste,mcde-dsi"; |
| reg = <0xa0352000 0x1000>; |
| clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>; |
| clock-names = "hs", "lp"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| dsi2: dsi-controller@a0353000 { |
| compatible = "ste,mcde-dsi"; |
| reg = <0xa0353000 0x1000>; |
| /* This DSI port only has the Low Power / Energy Save clock */ |
| clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>; |
| clock-names = "lp"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| cryp@a03cb000 { |
| compatible = "stericsson,ux500-cryp"; |
| reg = <0xa03cb000 0x1000>; |
| interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| |
| v-ape-supply = <&db8500_vape_reg>; |
| clocks = <&prcc_pclk 6 1>; |
| }; |
| |
| hash@a03c2000 { |
| compatible = "stericsson,ux500-hash"; |
| reg = <0xa03c2000 0x1000>; |
| |
| v-ape-supply = <&db8500_vape_reg>; |
| clocks = <&prcc_pclk 6 2>; |
| }; |
| }; |
| }; |
