| /* Copyright Statement: |
| * |
| * This software/firmware and related documentation ("MediaTek Software") are |
| * protected under relevant copyright laws. The information contained herein |
| * is confidential and proprietary to MediaTek Inc. and/or its licensors. |
| * Without the prior written permission of MediaTek inc. and/or its licensors, |
| * any reproduction, modification, use or disclosure of MediaTek Software, |
| * and information contained herein, in whole or in part, shall be strictly prohibited. |
| * |
| * MediaTek Inc. (C) 2010. All rights reserved. |
| * |
| * BY OPENING THIS FILE, RECEIVER HEREBY UNEQUIVOCALLY ACKNOWLEDGES AND AGREES |
| * THAT THE SOFTWARE/FIRMWARE AND ITS DOCUMENTATIONS ("MEDIATEK SOFTWARE") |
| * RECEIVED FROM MEDIATEK AND/OR ITS REPRESENTATIVES ARE PROVIDED TO RECEIVER ON |
| * AN "AS-IS" BASIS ONLY. MEDIATEK EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES, |
| * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF |
| * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. |
| * NEITHER DOES MEDIATEK PROVIDE ANY WARRANTY WHATSOEVER WITH RESPECT TO THE |
| * SOFTWARE OF ANY THIRD PARTY WHICH MAY BE USED BY, INCORPORATED IN, OR |
| * SUPPLIED WITH THE MEDIATEK SOFTWARE, AND RECEIVER AGREES TO LOOK ONLY TO SUCH |
| * THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO. RECEIVER EXPRESSLY ACKNOWLEDGES |
| * THAT IT IS RECEIVER'S SOLE RESPONSIBILITY TO OBTAIN FROM ANY THIRD PARTY ALL PROPER LICENSES |
| * CONTAINED IN MEDIATEK SOFTWARE. MEDIATEK SHALL ALSO NOT BE RESPONSIBLE FOR ANY MEDIATEK |
| * SOFTWARE RELEASES MADE TO RECEIVER'S SPECIFICATION OR TO CONFORM TO A PARTICULAR |
| * STANDARD OR OPEN FORUM. RECEIVER'S SOLE AND EXCLUSIVE REMEDY AND MEDIATEK'S ENTIRE AND |
| * CUMULATIVE LIABILITY WITH RESPECT TO THE MEDIATEK SOFTWARE RELEASED HEREUNDER WILL BE, |
| * AT MEDIATEK'S OPTION, TO REVISE OR REPLACE THE MEDIATEK SOFTWARE AT ISSUE, |
| * OR REFUND ANY SOFTWARE LICENSE FEES OR SERVICE CHARGE PAID BY RECEIVER TO |
| * MEDIATEK FOR SUCH MEDIATEK SOFTWARE AT ISSUE. |
| * |
| * The following software/firmware and/or related documentation ("MediaTek Software") |
| * have been modified by MediaTek Inc. All revisions are subject to any receiver's |
| * applicable license agreements with MediaTek Inc. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/delay.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/spinlock.h> |
| #include <linux/platform_device.h> |
| |
| #include <linux/mmc/host.h> |
| #include <linux/mmc/mmc.h> |
| #include <linux/mmc/sd.h> |
| #include <linux/mmc/sdio.h> |
| |
| #include <asm/mach-ralink/ralink_regs.h> |
| |
| #include "board.h" |
| #include "dbg.h" |
| #include "mt6575_sd.h" |
| |
| //#define IRQ_SDC 14 //MT7620 /*FIXME*/ |
| #ifdef CONFIG_SOC_MT7621 |
| #define RALINK_SYSCTL_BASE 0xbe000000 |
| #define RALINK_MSDC_BASE 0xbe130000 |
| #else |
| #define RALINK_SYSCTL_BASE 0xb0000000 |
| #define RALINK_MSDC_BASE 0xb0130000 |
| #endif |
| #define IRQ_SDC 22 /*FIXME*/ |
| |
| #define DRV_NAME "mtk-sd" |
| |
| #if defined(CONFIG_SOC_MT7620) |
| #define HOST_MAX_MCLK (48000000) /* +/- by chhung */ |
| #elif defined(CONFIG_SOC_MT7621) |
| #define HOST_MAX_MCLK (50000000) /* +/- by chhung */ |
| #endif |
| #define HOST_MIN_MCLK (260000) |
| |
| #define HOST_MAX_BLKSZ (2048) |
| |
| #define MSDC_OCR_AVAIL (MMC_VDD_28_29 | MMC_VDD_29_30 | MMC_VDD_30_31 | MMC_VDD_31_32 | MMC_VDD_32_33) |
| |
| #define GPIO_PULL_DOWN (0) |
| #define GPIO_PULL_UP (1) |
| |
| #if 0 /* --- by chhung */ |
| #define MSDC_CLKSRC_REG (0xf100000C) |
| #define PDN_REG (0xF1000010) |
| #endif /* end of --- */ |
| |
| #define DEFAULT_DEBOUNCE (8) /* 8 cycles */ |
| #define DEFAULT_DTOC (40) /* data timeout counter. 65536x40 sclk. */ |
| |
| #define CMD_TIMEOUT (HZ / 10) /* 100ms */ |
| #define DAT_TIMEOUT (HZ / 2 * 5) /* 500ms x5 */ |
| |
| #define MAX_DMA_CNT (64 * 1024 - 512) /* a single transaction for WIFI may be 50K*/ |
| |
| #define MAX_GPD_NUM (1 + 1) /* one null gpd */ |
| #define MAX_BD_NUM (1024) |
| #define MAX_BD_PER_GPD (MAX_BD_NUM) |
| |
| #define MAX_HW_SGMTS (MAX_BD_NUM) |
| #define MAX_PHY_SGMTS (MAX_BD_NUM) |
| #define MAX_SGMT_SZ (MAX_DMA_CNT) |
| #define MAX_REQ_SZ (MAX_SGMT_SZ * 8) |
| |
| static int cd_active_low = 1; |
| |
| //================================= |
| #define PERI_MSDC0_PDN (15) |
| //#define PERI_MSDC1_PDN (16) |
| //#define PERI_MSDC2_PDN (17) |
| //#define PERI_MSDC3_PDN (18) |
| |
| #if 0 /* --- by chhung */ |
| /* gate means clock power down */ |
| static int g_clk_gate = 0; |
| #define msdc_gate_clock(id) \ |
| do { \ |
| g_clk_gate &= ~(1 << ((id) + PERI_MSDC0_PDN)); \ |
| } while (0) |
| /* not like power down register. 1 means clock on. */ |
| #define msdc_ungate_clock(id) \ |
| do { \ |
| g_clk_gate |= 1 << ((id) + PERI_MSDC0_PDN); \ |
| } while (0) |
| |
| // do we need sync object or not |
| void msdc_clk_status(int *status) |
| { |
| *status = g_clk_gate; |
| } |
| #endif /* end of --- */ |
| |
| /* +++ by chhung */ |
| struct msdc_hw msdc0_hw = { |
| .clk_src = 0, |
| .flags = MSDC_CD_PIN_EN | MSDC_REMOVABLE, |
| // .flags = MSDC_WP_PIN_EN | MSDC_CD_PIN_EN | MSDC_REMOVABLE, |
| }; |
| |
| /* end of +++ */ |
| |
| static int msdc_rsp[] = { |
| 0, /* RESP_NONE */ |
| 1, /* RESP_R1 */ |
| 2, /* RESP_R2 */ |
| 3, /* RESP_R3 */ |
| 4, /* RESP_R4 */ |
| 1, /* RESP_R5 */ |
| 1, /* RESP_R6 */ |
| 1, /* RESP_R7 */ |
| 7, /* RESP_R1b */ |
| }; |
| |
| #define msdc_txfifocnt() ((sdr_read32(MSDC_FIFOCS) & MSDC_FIFOCS_TXCNT) >> 16) |
| #define msdc_rxfifocnt() ((sdr_read32(MSDC_FIFOCS) & MSDC_FIFOCS_RXCNT) >> 0) |
| #define msdc_fifo_write32(v) sdr_write32(MSDC_TXDATA, (v)) |
| #define msdc_fifo_write8(v) sdr_write8(MSDC_TXDATA, (v)) |
| #define msdc_fifo_read32() sdr_read32(MSDC_RXDATA) |
| #define msdc_fifo_read8() sdr_read8(MSDC_RXDATA) |
| |
| #define msdc_dma_on() sdr_clr_bits(MSDC_CFG, MSDC_CFG_PIO) |
| |
| #define msdc_retry(expr, retry, cnt) \ |
| do { \ |
| int backup = cnt; \ |
| while (retry) { \ |
| if (!(expr)) \ |
| break; \ |
| if (cnt-- == 0) { \ |
| retry--; mdelay(1); cnt = backup; \ |
| } \ |
| } \ |
| WARN_ON(retry == 0); \ |
| } while (0) |
| |
| static void msdc_reset_hw(struct msdc_host *host) |
| { |
| void __iomem *base = host->base; |
| |
| sdr_set_bits(MSDC_CFG, MSDC_CFG_RST); |
| while (sdr_read32(MSDC_CFG) & MSDC_CFG_RST) |
| cpu_relax(); |
| } |
| |
| #define msdc_clr_int() \ |
| do { \ |
| volatile u32 val = sdr_read32(MSDC_INT); \ |
| sdr_write32(MSDC_INT, val); \ |
| } while (0) |
| |
| #define msdc_clr_fifo() \ |
| do { \ |
| int retry = 3, cnt = 1000; \ |
| sdr_set_bits(MSDC_FIFOCS, MSDC_FIFOCS_CLR); \ |
| msdc_retry(sdr_read32(MSDC_FIFOCS) & MSDC_FIFOCS_CLR, retry, cnt); \ |
| } while (0) |
| |
| #define msdc_irq_save(val) \ |
| do { \ |
| val = sdr_read32(MSDC_INTEN); \ |
| sdr_clr_bits(MSDC_INTEN, val); \ |
| } while (0) |
| |
| #define msdc_irq_restore(val) \ |
| do { \ |
| sdr_set_bits(MSDC_INTEN, val); \ |
| } while (0) |
| |
| /* clock source for host: global */ |
| #if defined(CONFIG_SOC_MT7620) |
| static u32 hclks[] = {48000000}; /* +/- by chhung */ |
| #elif defined(CONFIG_SOC_MT7621) |
| static u32 hclks[] = {50000000}; /* +/- by chhung */ |
| #endif |
| |
| //============================================ |
| // the power for msdc host controller: global |
| // always keep the VMC on. |
| //============================================ |
| #define msdc_vcore_on(host) \ |
| do { \ |
| INIT_MSG("[+]VMC ref. count<%d>", ++host->pwr_ref); \ |
| (void)hwPowerOn(MT65XX_POWER_LDO_VMC, VOL_3300, "SD"); \ |
| } while (0) |
| #define msdc_vcore_off(host) \ |
| do { \ |
| INIT_MSG("[-]VMC ref. count<%d>", --host->pwr_ref); \ |
| (void)hwPowerDown(MT65XX_POWER_LDO_VMC, "SD"); \ |
| } while (0) |
| |
| //==================================== |
| // the vdd output for card: global |
| // always keep the VMCH on. |
| //==================================== |
| #define msdc_vdd_on(host) \ |
| do { \ |
| (void)hwPowerOn(MT65XX_POWER_LDO_VMCH, VOL_3300, "SD"); \ |
| } while (0) |
| #define msdc_vdd_off(host) \ |
| do { \ |
| (void)hwPowerDown(MT65XX_POWER_LDO_VMCH, "SD"); \ |
| } while (0) |
| |
| #define sdc_is_busy() (sdr_read32(SDC_STS) & SDC_STS_SDCBUSY) |
| #define sdc_is_cmd_busy() (sdr_read32(SDC_STS) & SDC_STS_CMDBUSY) |
| |
| #define sdc_send_cmd(cmd, arg) \ |
| do { \ |
| sdr_write32(SDC_ARG, (arg)); \ |
| sdr_write32(SDC_CMD, (cmd)); \ |
| } while (0) |
| |
| // can modify to read h/w register. |
| //#define is_card_present(h) ((sdr_read32(MSDC_PS) & MSDC_PS_CDSTS) ? 0 : 1); |
| #define is_card_present(h) (((struct msdc_host *)(h))->card_inserted) |
| |
| /* +++ by chhung */ |
| #ifndef __ASSEMBLY__ |
| #define PHYSADDR(a) (((unsigned long)(a)) & 0x1fffffff) |
| #else |
| #define PHYSADDR(a) ((a) & 0x1fffffff) |
| #endif |
| /* end of +++ */ |
| static unsigned int msdc_do_command(struct msdc_host *host, |
| struct mmc_command *cmd, |
| int tune, |
| unsigned long timeout); |
| |
| static int msdc_tune_cmdrsp(struct msdc_host *host, struct mmc_command *cmd); |
| |
| #ifdef MT6575_SD_DEBUG |
| static void msdc_dump_card_status(struct msdc_host *host, u32 status) |
| { |
| /* N_MSG is currently a no-op */ |
| #if 0 |
| static char *state[] = { |
| "Idle", /* 0 */ |
| "Ready", /* 1 */ |
| "Ident", /* 2 */ |
| "Stby", /* 3 */ |
| "Tran", /* 4 */ |
| "Data", /* 5 */ |
| "Rcv", /* 6 */ |
| "Prg", /* 7 */ |
| "Dis", /* 8 */ |
| "Reserved", /* 9 */ |
| "Reserved", /* 10 */ |
| "Reserved", /* 11 */ |
| "Reserved", /* 12 */ |
| "Reserved", /* 13 */ |
| "Reserved", /* 14 */ |
| "I/O mode", /* 15 */ |
| }; |
| #endif |
| if (status & R1_OUT_OF_RANGE) |
| N_MSG(RSP, "[CARD_STATUS] Out of Range"); |
| if (status & R1_ADDRESS_ERROR) |
| N_MSG(RSP, "[CARD_STATUS] Address Error"); |
| if (status & R1_BLOCK_LEN_ERROR) |
| N_MSG(RSP, "[CARD_STATUS] Block Len Error"); |
| if (status & R1_ERASE_SEQ_ERROR) |
| N_MSG(RSP, "[CARD_STATUS] Erase Seq Error"); |
| if (status & R1_ERASE_PARAM) |
| N_MSG(RSP, "[CARD_STATUS] Erase Param"); |
| if (status & R1_WP_VIOLATION) |
| N_MSG(RSP, "[CARD_STATUS] WP Violation"); |
| if (status & R1_CARD_IS_LOCKED) |
| N_MSG(RSP, "[CARD_STATUS] Card is Locked"); |
| if (status & R1_LOCK_UNLOCK_FAILED) |
| N_MSG(RSP, "[CARD_STATUS] Lock/Unlock Failed"); |
| if (status & R1_COM_CRC_ERROR) |
| N_MSG(RSP, "[CARD_STATUS] Command CRC Error"); |
| if (status & R1_ILLEGAL_COMMAND) |
| N_MSG(RSP, "[CARD_STATUS] Illegal Command"); |
| if (status & R1_CARD_ECC_FAILED) |
| N_MSG(RSP, "[CARD_STATUS] Card ECC Failed"); |
| if (status & R1_CC_ERROR) |
| N_MSG(RSP, "[CARD_STATUS] CC Error"); |
| if (status & R1_ERROR) |
| N_MSG(RSP, "[CARD_STATUS] Error"); |
| if (status & R1_UNDERRUN) |
| N_MSG(RSP, "[CARD_STATUS] Underrun"); |
| if (status & R1_OVERRUN) |
| N_MSG(RSP, "[CARD_STATUS] Overrun"); |
| if (status & R1_CID_CSD_OVERWRITE) |
| N_MSG(RSP, "[CARD_STATUS] CID/CSD Overwrite"); |
| if (status & R1_WP_ERASE_SKIP) |
| N_MSG(RSP, "[CARD_STATUS] WP Eraser Skip"); |
| if (status & R1_CARD_ECC_DISABLED) |
| N_MSG(RSP, "[CARD_STATUS] Card ECC Disabled"); |
| if (status & R1_ERASE_RESET) |
| N_MSG(RSP, "[CARD_STATUS] Erase Reset"); |
| if (status & R1_READY_FOR_DATA) |
| N_MSG(RSP, "[CARD_STATUS] Ready for Data"); |
| if (status & R1_SWITCH_ERROR) |
| N_MSG(RSP, "[CARD_STATUS] Switch error"); |
| if (status & R1_APP_CMD) |
| N_MSG(RSP, "[CARD_STATUS] App Command"); |
| |
| N_MSG(RSP, "[CARD_STATUS] '%s' State", state[R1_CURRENT_STATE(status)]); |
| } |
| |
| static void msdc_dump_ocr_reg(struct msdc_host *host, u32 resp) |
| { |
| if (resp & (1 << 7)) |
| N_MSG(RSP, "[OCR] Low Voltage Range"); |
| if (resp & (1 << 15)) |
| N_MSG(RSP, "[OCR] 2.7-2.8 volt"); |
| if (resp & (1 << 16)) |
| N_MSG(RSP, "[OCR] 2.8-2.9 volt"); |
| if (resp & (1 << 17)) |
| N_MSG(RSP, "[OCR] 2.9-3.0 volt"); |
| if (resp & (1 << 18)) |
| N_MSG(RSP, "[OCR] 3.0-3.1 volt"); |
| if (resp & (1 << 19)) |
| N_MSG(RSP, "[OCR] 3.1-3.2 volt"); |
| if (resp & (1 << 20)) |
| N_MSG(RSP, "[OCR] 3.2-3.3 volt"); |
| if (resp & (1 << 21)) |
| N_MSG(RSP, "[OCR] 3.3-3.4 volt"); |
| if (resp & (1 << 22)) |
| N_MSG(RSP, "[OCR] 3.4-3.5 volt"); |
| if (resp & (1 << 23)) |
| N_MSG(RSP, "[OCR] 3.5-3.6 volt"); |
| if (resp & (1 << 24)) |
| N_MSG(RSP, "[OCR] Switching to 1.8V Accepted (S18A)"); |
| if (resp & (1 << 30)) |
| N_MSG(RSP, "[OCR] Card Capacity Status (CCS)"); |
| if (resp & (1 << 31)) |
| N_MSG(RSP, "[OCR] Card Power Up Status (Idle)"); |
| else |
| N_MSG(RSP, "[OCR] Card Power Up Status (Busy)"); |
| } |
| |
| static void msdc_dump_rca_resp(struct msdc_host *host, u32 resp) |
| { |
| u32 status = (((resp >> 15) & 0x1) << 23) | |
| (((resp >> 14) & 0x1) << 22) | |
| (((resp >> 13) & 0x1) << 19) | |
| (resp & 0x1fff); |
| |
| N_MSG(RSP, "[RCA] 0x%.4x", resp >> 16); |
| msdc_dump_card_status(host, status); |
| } |
| |
| static void msdc_dump_io_resp(struct msdc_host *host, u32 resp) |
| { |
| u32 flags = (resp >> 8) & 0xFF; |
| #if 0 |
| char *state[] = {"DIS", "CMD", "TRN", "RFU"}; |
| #endif |
| if (flags & (1 << 7)) |
| N_MSG(RSP, "[IO] COM_CRC_ERR"); |
| if (flags & (1 << 6)) |
| N_MSG(RSP, "[IO] Illegal command"); |
| if (flags & (1 << 3)) |
| N_MSG(RSP, "[IO] Error"); |
| if (flags & (1 << 2)) |
| N_MSG(RSP, "[IO] RFU"); |
| if (flags & (1 << 1)) |
| N_MSG(RSP, "[IO] Function number error"); |
| if (flags & (1 << 0)) |
| N_MSG(RSP, "[IO] Out of range"); |
| |
| N_MSG(RSP, "[IO] State: %s, Data:0x%x", state[(resp >> 12) & 0x3], resp & 0xFF); |
| } |
| #endif |
| |
| static void msdc_set_timeout(struct msdc_host *host, u32 ns, u32 clks) |
| { |
| void __iomem *base = host->base; |
| u32 timeout, clk_ns; |
| |
| host->timeout_ns = ns; |
| host->timeout_clks = clks; |
| |
| clk_ns = 1000000000UL / host->sclk; |
| timeout = ns / clk_ns + clks; |
| timeout = timeout >> 16; /* in 65536 sclk cycle unit */ |
| timeout = timeout > 1 ? timeout - 1 : 0; |
| timeout = timeout > 255 ? 255 : timeout; |
| |
| sdr_set_field(SDC_CFG, SDC_CFG_DTOC, timeout); |
| |
| N_MSG(OPS, "Set read data timeout: %dns %dclks -> %d x 65536 cycles", |
| ns, clks, timeout + 1); |
| } |
| |
| static void msdc_tasklet_card(struct work_struct *work) |
| { |
| struct msdc_host *host = (struct msdc_host *)container_of(work, |
| struct msdc_host, card_delaywork.work); |
| void __iomem *base = host->base; |
| u32 inserted; |
| u32 status = 0; |
| //u32 change = 0; |
| |
| spin_lock(&host->lock); |
| |
| status = sdr_read32(MSDC_PS); |
| if (cd_active_low) |
| inserted = (status & MSDC_PS_CDSTS) ? 0 : 1; |
| else |
| inserted = (status & MSDC_PS_CDSTS) ? 1 : 0; |
| |
| #if 0 |
| change = host->card_inserted ^ inserted; |
| host->card_inserted = inserted; |
| |
| if (change && !host->suspend) { |
| if (inserted) |
| host->mmc->f_max = HOST_MAX_MCLK; // work around |
| mmc_detect_change(host->mmc, msecs_to_jiffies(20)); |
| } |
| #else /* Make sure: handle the last interrupt */ |
| host->card_inserted = inserted; |
| |
| if (!host->suspend) { |
| host->mmc->f_max = HOST_MAX_MCLK; |
| mmc_detect_change(host->mmc, msecs_to_jiffies(20)); |
| } |
| |
| IRQ_MSG("card found<%s>", inserted ? "inserted" : "removed"); |
| #endif |
| |
| spin_unlock(&host->lock); |
| } |
| |
| #if 0 /* --- by chhung */ |
| /* For E2 only */ |
| static u8 clk_src_bit[4] = { |
| 0, 3, 5, 7 |
| }; |
| |
| static void msdc_select_clksrc(struct msdc_host *host, unsigned char clksrc) |
| { |
| u32 val; |
| void __iomem *base = host->base; |
| |
| BUG_ON(clksrc > 3); |
| INIT_MSG("set clock source to <%d>", clksrc); |
| |
| val = sdr_read32(MSDC_CLKSRC_REG); |
| if (sdr_read32(MSDC_ECO_VER) >= 4) { |
| val &= ~(0x3 << clk_src_bit[host->id]); |
| val |= clksrc << clk_src_bit[host->id]; |
| } else { |
| val &= ~0x3; val |= clksrc; |
| } |
| sdr_write32(MSDC_CLKSRC_REG, val); |
| |
| host->hclk = hclks[clksrc]; |
| host->hw->clk_src = clksrc; |
| } |
| #endif /* end of --- */ |
| |
| static void msdc_set_mclk(struct msdc_host *host, int ddr, unsigned int hz) |
| { |
| //struct msdc_hw *hw = host->hw; |
| void __iomem *base = host->base; |
| u32 mode; |
| u32 flags; |
| u32 div; |
| u32 sclk; |
| u32 hclk = host->hclk; |
| //u8 clksrc = hw->clk_src; |
| |
| if (!hz) { // set mmc system clock to 0 ? |
| //ERR_MSG("set mclk to 0!!!"); |
| msdc_reset_hw(host); |
| return; |
| } |
| |
| msdc_irq_save(flags); |
| |
| if (ddr) { |
| mode = 0x2; /* ddr mode and use divisor */ |
| if (hz >= (hclk >> 2)) { |
| div = 1; /* mean div = 1/4 */ |
| sclk = hclk >> 2; /* sclk = clk / 4 */ |
| } else { |
| div = (hclk + ((hz << 2) - 1)) / (hz << 2); |
| sclk = (hclk >> 2) / div; |
| } |
| } else if (hz >= hclk) { /* bug fix */ |
| mode = 0x1; /* no divisor and divisor is ignored */ |
| div = 0; |
| sclk = hclk; |
| } else { |
| mode = 0x0; /* use divisor */ |
| if (hz >= (hclk >> 1)) { |
| div = 0; /* mean div = 1/2 */ |
| sclk = hclk >> 1; /* sclk = clk / 2 */ |
| } else { |
| div = (hclk + ((hz << 2) - 1)) / (hz << 2); |
| sclk = (hclk >> 2) / div; |
| } |
| } |
| |
| /* set clock mode and divisor */ |
| sdr_set_field(MSDC_CFG, MSDC_CFG_CKMOD, mode); |
| sdr_set_field(MSDC_CFG, MSDC_CFG_CKDIV, div); |
| |
| /* wait clock stable */ |
| while (!(sdr_read32(MSDC_CFG) & MSDC_CFG_CKSTB)) |
| cpu_relax(); |
| |
| host->sclk = sclk; |
| host->mclk = hz; |
| msdc_set_timeout(host, host->timeout_ns, host->timeout_clks); // need? |
| |
| INIT_MSG("================"); |
| INIT_MSG("!!! Set<%dKHz> Source<%dKHz> -> sclk<%dKHz>", hz / 1000, hclk / 1000, sclk / 1000); |
| INIT_MSG("================"); |
| |
| msdc_irq_restore(flags); |
| } |
| |
| /* Fix me. when need to abort */ |
| static void msdc_abort_data(struct msdc_host *host) |
| { |
| void __iomem *base = host->base; |
| struct mmc_command *stop = host->mrq->stop; |
| |
| ERR_MSG("Need to Abort."); |
| |
| msdc_reset_hw(host); |
| msdc_clr_fifo(); |
| msdc_clr_int(); |
| |
| // need to check FIFO count 0 ? |
| |
| if (stop) { /* try to stop, but may not success */ |
| ERR_MSG("stop when abort CMD<%d>", stop->opcode); |
| (void)msdc_do_command(host, stop, 0, CMD_TIMEOUT); |
| } |
| |
| //if (host->mclk >= 25000000) { |
| // msdc_set_mclk(host, 0, host->mclk >> 1); |
| //} |
| } |
| |
| #if 0 /* --- by chhung */ |
| static void msdc_pin_config(struct msdc_host *host, int mode) |
| { |
| struct msdc_hw *hw = host->hw; |
| void __iomem *base = host->base; |
| int pull = (mode == MSDC_PIN_PULL_UP) ? GPIO_PULL_UP : GPIO_PULL_DOWN; |
| |
| /* Config WP pin */ |
| if (hw->flags & MSDC_WP_PIN_EN) { |
| if (hw->config_gpio_pin) /* NULL */ |
| hw->config_gpio_pin(MSDC_WP_PIN, pull); |
| } |
| |
| switch (mode) { |
| case MSDC_PIN_PULL_UP: |
| //sdr_set_field(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKPU, 1); /* Check & FIXME */ |
| //sdr_set_field(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKPD, 0); /* Check & FIXME */ |
| sdr_set_field(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDPU, 1); |
| sdr_set_field(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDPD, 0); |
| sdr_set_field(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATPU, 1); |
| sdr_set_field(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATPD, 0); |
| break; |
| case MSDC_PIN_PULL_DOWN: |
| //sdr_set_field(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKPU, 0); /* Check & FIXME */ |
| //sdr_set_field(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKPD, 1); /* Check & FIXME */ |
| sdr_set_field(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDPU, 0); |
| sdr_set_field(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDPD, 1); |
| sdr_set_field(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATPU, 0); |
| sdr_set_field(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATPD, 1); |
| break; |
| case MSDC_PIN_PULL_NONE: |
| default: |
| //sdr_set_field(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKPU, 0); /* Check & FIXME */ |
| //sdr_set_field(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKPD, 0); /* Check & FIXME */ |
| sdr_set_field(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDPU, 0); |
| sdr_set_field(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDPD, 0); |
| sdr_set_field(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATPU, 0); |
| sdr_set_field(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATPD, 0); |
| break; |
| } |
| |
| N_MSG(CFG, "Pins mode(%d), down(%d), up(%d)", |
| mode, MSDC_PIN_PULL_DOWN, MSDC_PIN_PULL_UP); |
| } |
| |
| void msdc_pin_reset(struct msdc_host *host, int mode) |
| { |
| struct msdc_hw *hw = (struct msdc_hw *)host->hw; |
| void __iomem *base = host->base; |
| int pull = (mode == MSDC_PIN_PULL_UP) ? GPIO_PULL_UP : GPIO_PULL_DOWN; |
| |
| /* Config reset pin */ |
| if (hw->flags & MSDC_RST_PIN_EN) { |
| if (hw->config_gpio_pin) /* NULL */ |
| hw->config_gpio_pin(MSDC_RST_PIN, pull); |
| |
| if (mode == MSDC_PIN_PULL_UP) |
| sdr_clr_bits(EMMC_IOCON, EMMC_IOCON_BOOTRST); |
| else |
| sdr_set_bits(EMMC_IOCON, EMMC_IOCON_BOOTRST); |
| } |
| } |
| |
| static void msdc_core_power(struct msdc_host *host, int on) |
| { |
| N_MSG(CFG, "Turn %s %s power (copower: %d -> %d)", |
| on ? "on" : "off", "core", host->core_power, on); |
| |
| if (on && host->core_power == 0) { |
| msdc_vcore_on(host); |
| host->core_power = 1; |
| msleep(1); |
| } else if (!on && host->core_power == 1) { |
| msdc_vcore_off(host); |
| host->core_power = 0; |
| msleep(1); |
| } |
| } |
| |
| static void msdc_host_power(struct msdc_host *host, int on) |
| { |
| N_MSG(CFG, "Turn %s %s power ", on ? "on" : "off", "host"); |
| |
| if (on) { |
| //msdc_core_power(host, 1); // need do card detection. |
| msdc_pin_reset(host, MSDC_PIN_PULL_UP); |
| } else { |
| msdc_pin_reset(host, MSDC_PIN_PULL_DOWN); |
| //msdc_core_power(host, 0); |
| } |
| } |
| |
| static void msdc_card_power(struct msdc_host *host, int on) |
| { |
| N_MSG(CFG, "Turn %s %s power ", on ? "on" : "off", "card"); |
| |
| if (on) { |
| msdc_pin_config(host, MSDC_PIN_PULL_UP); |
| //msdc_vdd_on(host); // need todo card detection. |
| msleep(1); |
| } else { |
| //msdc_vdd_off(host); |
| msdc_pin_config(host, MSDC_PIN_PULL_DOWN); |
| msleep(1); |
| } |
| } |
| |
| static void msdc_set_power_mode(struct msdc_host *host, u8 mode) |
| { |
| N_MSG(CFG, "Set power mode(%d)", mode); |
| |
| if (host->power_mode == MMC_POWER_OFF && mode != MMC_POWER_OFF) { |
| msdc_host_power(host, 1); |
| msdc_card_power(host, 1); |
| } else if (host->power_mode != MMC_POWER_OFF && mode == MMC_POWER_OFF) { |
| msdc_card_power(host, 0); |
| msdc_host_power(host, 0); |
| } |
| host->power_mode = mode; |
| } |
| #endif /* end of --- */ |
| |
| #ifdef CONFIG_PM |
| /* |
| register as callback function of WIFI(combo_sdio_register_pm) . |
| can called by msdc_drv_suspend/resume too. |
| */ |
| static void msdc_pm(pm_message_t state, void *data) |
| { |
| struct msdc_host *host = (struct msdc_host *)data; |
| int evt = state.event; |
| |
| if (evt == PM_EVENT_USER_RESUME || evt == PM_EVENT_USER_SUSPEND) { |
| INIT_MSG("USR_%s: suspend<%d> power<%d>", |
| evt == PM_EVENT_USER_RESUME ? "EVENT_USER_RESUME" : "EVENT_USER_SUSPEND", |
| host->suspend, host->power_mode); |
| } |
| |
| if (evt == PM_EVENT_SUSPEND || evt == PM_EVENT_USER_SUSPEND) { |
| if (host->suspend) /* already suspend */ /* default 0*/ |
| return; |
| |
| /* for memory card. already power off by mmc */ |
| if (evt == PM_EVENT_SUSPEND && host->power_mode == MMC_POWER_OFF) |
| return; |
| |
| host->suspend = 1; |
| host->pm_state = state; /* default PMSG_RESUME */ |
| |
| } else if (evt == PM_EVENT_RESUME || evt == PM_EVENT_USER_RESUME) { |
| if (!host->suspend) { |
| //ERR_MSG("warning: already resume"); |
| return; |
| } |
| |
| /* No PM resume when USR suspend */ |
| if (evt == PM_EVENT_RESUME && host->pm_state.event == PM_EVENT_USER_SUSPEND) { |
| ERR_MSG("PM Resume when in USR Suspend"); /* won't happen. */ |
| return; |
| } |
| |
| host->suspend = 0; |
| host->pm_state = state; |
| |
| } |
| } |
| #endif |
| |
| /*--------------------------------------------------------------------------*/ |
| /* mmc_host_ops members */ |
| /*--------------------------------------------------------------------------*/ |
| static unsigned int msdc_command_start(struct msdc_host *host, |
| struct mmc_command *cmd, |
| int tune, /* not used */ |
| unsigned long timeout) |
| { |
| void __iomem *base = host->base; |
| u32 opcode = cmd->opcode; |
| u32 rawcmd; |
| u32 wints = MSDC_INT_CMDRDY | MSDC_INT_RSPCRCERR | MSDC_INT_CMDTMO | |
| MSDC_INT_ACMDRDY | MSDC_INT_ACMDCRCERR | MSDC_INT_ACMDTMO | |
| MSDC_INT_ACMD19_DONE; |
| |
| u32 resp; |
| unsigned long tmo; |
| |
| /* Protocol layer does not provide response type, but our hardware needs |
| * to know exact type, not just size! |
| */ |
| if (opcode == MMC_SEND_OP_COND || opcode == SD_APP_OP_COND) { |
| resp = RESP_R3; |
| } else if (opcode == MMC_SET_RELATIVE_ADDR) { |
| resp = (mmc_cmd_type(cmd) == MMC_CMD_BCR) ? RESP_R6 : RESP_R1; |
| } else if (opcode == MMC_FAST_IO) { |
| resp = RESP_R4; |
| } else if (opcode == MMC_GO_IRQ_STATE) { |
| resp = RESP_R5; |
| } else if (opcode == MMC_SELECT_CARD) { |
| resp = (cmd->arg != 0) ? RESP_R1B : RESP_NONE; |
| } else if (opcode == SD_IO_RW_DIRECT || opcode == SD_IO_RW_EXTENDED) { |
| resp = RESP_R1; /* SDIO workaround. */ |
| } else if (opcode == SD_SEND_IF_COND && (mmc_cmd_type(cmd) == MMC_CMD_BCR)) { |
| resp = RESP_R1; |
| } else { |
| switch (mmc_resp_type(cmd)) { |
| case MMC_RSP_R1: |
| resp = RESP_R1; |
| break; |
| case MMC_RSP_R1B: |
| resp = RESP_R1B; |
| break; |
| case MMC_RSP_R2: |
| resp = RESP_R2; |
| break; |
| case MMC_RSP_R3: |
| resp = RESP_R3; |
| break; |
| case MMC_RSP_NONE: |
| default: |
| resp = RESP_NONE; |
| break; |
| } |
| } |
| |
| cmd->error = 0; |
| /* rawcmd : |
| * vol_swt << 30 | auto_cmd << 28 | blklen << 16 | go_irq << 15 | |
| * stop << 14 | rw << 13 | dtype << 11 | rsptyp << 7 | brk << 6 | opcode |
| */ |
| rawcmd = opcode | msdc_rsp[resp] << 7 | host->blksz << 16; |
| |
| if (opcode == MMC_READ_MULTIPLE_BLOCK) { |
| rawcmd |= (2 << 11); |
| } else if (opcode == MMC_READ_SINGLE_BLOCK) { |
| rawcmd |= (1 << 11); |
| } else if (opcode == MMC_WRITE_MULTIPLE_BLOCK) { |
| rawcmd |= ((2 << 11) | (1 << 13)); |
| } else if (opcode == MMC_WRITE_BLOCK) { |
| rawcmd |= ((1 << 11) | (1 << 13)); |
| } else if (opcode == SD_IO_RW_EXTENDED) { |
| if (cmd->data->flags & MMC_DATA_WRITE) |
| rawcmd |= (1 << 13); |
| if (cmd->data->blocks > 1) |
| rawcmd |= (2 << 11); |
| else |
| rawcmd |= (1 << 11); |
| } else if (opcode == SD_IO_RW_DIRECT && cmd->flags == (unsigned int)-1) { |
| rawcmd |= (1 << 14); |
| } else if ((opcode == SD_APP_SEND_SCR) || |
| (opcode == SD_APP_SEND_NUM_WR_BLKS) || |
| (opcode == SD_SWITCH && (mmc_cmd_type(cmd) == MMC_CMD_ADTC)) || |
| (opcode == SD_APP_SD_STATUS && (mmc_cmd_type(cmd) == MMC_CMD_ADTC)) || |
| (opcode == MMC_SEND_EXT_CSD && (mmc_cmd_type(cmd) == MMC_CMD_ADTC))) { |
| rawcmd |= (1 << 11); |
| } else if (opcode == MMC_STOP_TRANSMISSION) { |
| rawcmd |= (1 << 14); |
| rawcmd &= ~(0x0FFF << 16); |
| } |
| |
| N_MSG(CMD, "CMD<%d><0x%.8x> Arg<0x%.8x>", opcode, rawcmd, cmd->arg); |
| |
| tmo = jiffies + timeout; |
| |
| if (opcode == MMC_SEND_STATUS) { |
| for (;;) { |
| if (!sdc_is_cmd_busy()) |
| break; |
| |
| if (time_after(jiffies, tmo)) { |
| ERR_MSG("XXX cmd_busy timeout: before CMD<%d>", opcode); |
| cmd->error = -ETIMEDOUT; |
| msdc_reset_hw(host); |
| goto end; |
| } |
| } |
| } else { |
| for (;;) { |
| if (!sdc_is_busy()) |
| break; |
| if (time_after(jiffies, tmo)) { |
| ERR_MSG("XXX sdc_busy timeout: before CMD<%d>", opcode); |
| cmd->error = -ETIMEDOUT; |
| msdc_reset_hw(host); |
| goto end; |
| } |
| } |
| } |
| |
| //BUG_ON(in_interrupt()); |
| host->cmd = cmd; |
| host->cmd_rsp = resp; |
| |
| init_completion(&host->cmd_done); |
| |
| sdr_set_bits(MSDC_INTEN, wints); |
| sdc_send_cmd(rawcmd, cmd->arg); |
| |
| end: |
| return cmd->error; |
| } |
| |
| static unsigned int msdc_command_resp(struct msdc_host *host, |
| struct mmc_command *cmd, |
| int tune, |
| unsigned long timeout) |
| __must_hold(&host->lock) |
| { |
| void __iomem *base = host->base; |
| u32 opcode = cmd->opcode; |
| //u32 rawcmd; |
| u32 resp; |
| u32 wints = MSDC_INT_CMDRDY | MSDC_INT_RSPCRCERR | MSDC_INT_CMDTMO | |
| MSDC_INT_ACMDRDY | MSDC_INT_ACMDCRCERR | MSDC_INT_ACMDTMO | |
| MSDC_INT_ACMD19_DONE; |
| |
| resp = host->cmd_rsp; |
| |
| BUG_ON(in_interrupt()); |
| //init_completion(&host->cmd_done); |
| //sdr_set_bits(MSDC_INTEN, wints); |
| |
| spin_unlock(&host->lock); |
| if (!wait_for_completion_timeout(&host->cmd_done, 10 * timeout)) { |
| ERR_MSG("XXX CMD<%d> wait_for_completion timeout ARG<0x%.8x>", opcode, cmd->arg); |
| cmd->error = -ETIMEDOUT; |
| msdc_reset_hw(host); |
| } |
| spin_lock(&host->lock); |
| |
| sdr_clr_bits(MSDC_INTEN, wints); |
| host->cmd = NULL; |
| |
| //end: |
| #ifdef MT6575_SD_DEBUG |
| switch (resp) { |
| case RESP_NONE: |
| N_MSG(RSP, "CMD_RSP(%d): %d RSP(%d)", opcode, cmd->error, resp); |
| break; |
| case RESP_R2: |
| N_MSG(RSP, "CMD_RSP(%d): %d RSP(%d)= %.8x %.8x %.8x %.8x", |
| opcode, cmd->error, resp, cmd->resp[0], cmd->resp[1], |
| cmd->resp[2], cmd->resp[3]); |
| break; |
| default: /* Response types 1, 3, 4, 5, 6, 7(1b) */ |
| N_MSG(RSP, "CMD_RSP(%d): %d RSP(%d)= 0x%.8x", |
| opcode, cmd->error, resp, cmd->resp[0]); |
| if (cmd->error == 0) { |
| switch (resp) { |
| case RESP_R1: |
| case RESP_R1B: |
| msdc_dump_card_status(host, cmd->resp[0]); |
| break; |
| case RESP_R3: |
| msdc_dump_ocr_reg(host, cmd->resp[0]); |
| break; |
| case RESP_R5: |
| msdc_dump_io_resp(host, cmd->resp[0]); |
| break; |
| case RESP_R6: |
| msdc_dump_rca_resp(host, cmd->resp[0]); |
| break; |
| } |
| } |
| break; |
| } |
| #endif |
| |
| /* do we need to save card's RCA when SD_SEND_RELATIVE_ADDR */ |
| |
| if (!tune) |
| return cmd->error; |
| |
| /* memory card CRC */ |
| if (host->hw->flags & MSDC_REMOVABLE && cmd->error == -EIO) { |
| if (sdr_read32(SDC_CMD) & 0x1800) { /* check if has data phase */ |
| msdc_abort_data(host); |
| } else { |
| /* do basic: reset*/ |
| msdc_reset_hw(host); |
| msdc_clr_fifo(); |
| msdc_clr_int(); |
| } |
| cmd->error = msdc_tune_cmdrsp(host, cmd); |
| } |
| |
| // check DAT0 |
| /* if (resp == RESP_R1B) { |
| while ((sdr_read32(MSDC_PS) & 0x10000) != 0x10000); |
| } */ |
| /* CMD12 Error Handle */ |
| |
| return cmd->error; |
| } |
| |
| static unsigned int msdc_do_command(struct msdc_host *host, |
| struct mmc_command *cmd, |
| int tune, |
| unsigned long timeout) |
| { |
| if (msdc_command_start(host, cmd, tune, timeout)) |
| goto end; |
| |
| if (msdc_command_resp(host, cmd, tune, timeout)) |
| goto end; |
| |
| end: |
| |
| N_MSG(CMD, " return<%d> resp<0x%.8x>", cmd->error, cmd->resp[0]); |
| return cmd->error; |
| } |
| |
| #if 0 /* --- by chhung */ |
| // DMA resume / start / stop |
| static void msdc_dma_resume(struct msdc_host *host) |
| { |
| void __iomem *base = host->base; |
| |
| sdr_set_field(MSDC_DMA_CTRL, MSDC_DMA_CTRL_RESUME, 1); |
| |
| N_MSG(DMA, "DMA resume"); |
| } |
| #endif /* end of --- */ |
| |
| static void msdc_dma_start(struct msdc_host *host) |
| { |
| void __iomem *base = host->base; |
| u32 wints = MSDC_INTEN_XFER_COMPL | MSDC_INTEN_DATTMO | MSDC_INTEN_DATCRCERR; |
| |
| sdr_set_bits(MSDC_INTEN, wints); |
| //dsb(); /* --- by chhung */ |
| sdr_set_field(MSDC_DMA_CTRL, MSDC_DMA_CTRL_START, 1); |
| |
| N_MSG(DMA, "DMA start"); |
| } |
| |
| static void msdc_dma_stop(struct msdc_host *host) |
| { |
| void __iomem *base = host->base; |
| //u32 retries=500; |
| u32 wints = MSDC_INTEN_XFER_COMPL | MSDC_INTEN_DATTMO | MSDC_INTEN_DATCRCERR; |
| |
| N_MSG(DMA, "DMA status: 0x%.8x", sdr_read32(MSDC_DMA_CFG)); |
| //while (sdr_read32(MSDC_DMA_CFG) & MSDC_DMA_CFG_STS); |
| |
| sdr_set_field(MSDC_DMA_CTRL, MSDC_DMA_CTRL_STOP, 1); |
| while (sdr_read32(MSDC_DMA_CFG) & MSDC_DMA_CFG_STS) |
| ; |
| |
| //dsb(); /* --- by chhung */ |
| sdr_clr_bits(MSDC_INTEN, wints); /* Not just xfer_comp */ |
| |
| N_MSG(DMA, "DMA stop"); |
| } |
| |
| /* calc checksum */ |
| static u8 msdc_dma_calcs(u8 *buf, u32 len) |
| { |
| u32 i, sum = 0; |
| |
| for (i = 0; i < len; i++) |
| sum += buf[i]; |
| return 0xFF - (u8)sum; |
| } |
| |
| /* gpd bd setup + dma registers */ |
| static void msdc_dma_config(struct msdc_host *host, struct msdc_dma *dma) |
| { |
| void __iomem *base = host->base; |
| //u32 i, j, num, bdlen, arg, xfersz; |
| u32 j, num; |
| struct scatterlist *sg; |
| struct gpd *gpd; |
| struct bd *bd; |
| |
| switch (dma->mode) { |
| case MSDC_MODE_DMA_BASIC: |
| BUG_ON(host->xfer_size > 65535); |
| BUG_ON(dma->sglen != 1); |
| sdr_write32(MSDC_DMA_SA, PHYSADDR(sg_dma_address(sg))); |
| sdr_set_field(MSDC_DMA_CTRL, MSDC_DMA_CTRL_LASTBUF, 1); |
| //#if defined (CONFIG_RALINK_MT7620) |
| if (ralink_soc == MT762X_SOC_MT7620A) |
| sdr_set_field(MSDC_DMA_CTRL, MSDC_DMA_CTRL_XFERSZ, sg_dma_len(sg)); |
| //#elif defined (CONFIG_RALINK_MT7621) || defined (CONFIG_RALINK_MT7628) |
| else |
| sdr_write32((void __iomem *)(RALINK_MSDC_BASE + 0xa8), sg_dma_len(sg)); |
| //#endif |
| sdr_set_field(MSDC_DMA_CTRL, MSDC_DMA_CTRL_BRUSTSZ, |
| MSDC_BRUST_64B); |
| sdr_set_field(MSDC_DMA_CTRL, MSDC_DMA_CTRL_MODE, 0); |
| break; |
| case MSDC_MODE_DMA_DESC: |
| |
| /* calculate the required number of gpd */ |
| num = (dma->sglen + MAX_BD_PER_GPD - 1) / MAX_BD_PER_GPD; |
| BUG_ON(num != 1); |
| |
| gpd = dma->gpd; |
| bd = dma->bd; |
| |
| /* modify gpd*/ |
| //gpd->intr = 0; |
| gpd->hwo = 1; /* hw will clear it */ |
| gpd->bdp = 1; |
| gpd->chksum = 0; /* need to clear first. */ |
| gpd->chksum = msdc_dma_calcs((u8 *)gpd, 16); |
| |
| /* modify bd*/ |
| for_each_sg(dma->sg, sg, dma->sglen, j) { |
| bd[j].blkpad = 0; |
| bd[j].dwpad = 0; |
| bd[j].ptr = (void *)sg_dma_address(sg); |
| bd[j].buflen = sg_dma_len(sg); |
| |
| if (j == dma->sglen - 1) |
| bd[j].eol = 1; /* the last bd */ |
| else |
| bd[j].eol = 0; |
| |
| bd[j].chksum = 0; /* checksume need to clear first */ |
| bd[j].chksum = msdc_dma_calcs((u8 *)(&bd[j]), 16); |
| } |
| |
| sdr_set_field(MSDC_DMA_CFG, MSDC_DMA_CFG_DECSEN, 1); |
| sdr_set_field(MSDC_DMA_CTRL, MSDC_DMA_CTRL_BRUSTSZ, |
| MSDC_BRUST_64B); |
| sdr_set_field(MSDC_DMA_CTRL, MSDC_DMA_CTRL_MODE, 1); |
| |
| sdr_write32(MSDC_DMA_SA, PHYSADDR((u32)dma->gpd_addr)); |
| break; |
| |
| default: |
| break; |
| } |
| |
| N_MSG(DMA, "DMA_CTRL = 0x%x", sdr_read32(MSDC_DMA_CTRL)); |
| N_MSG(DMA, "DMA_CFG = 0x%x", sdr_read32(MSDC_DMA_CFG)); |
| N_MSG(DMA, "DMA_SA = 0x%x", sdr_read32(MSDC_DMA_SA)); |
| |
| } |
| |
| static void msdc_dma_setup(struct msdc_host *host, struct msdc_dma *dma, |
| struct scatterlist *sg, unsigned int sglen) |
| { |
| BUG_ON(sglen > MAX_BD_NUM); /* not support currently */ |
| |
| dma->sg = sg; |
| dma->sglen = sglen; |
| |
| dma->mode = MSDC_MODE_DMA_DESC; |
| |
| N_MSG(DMA, "DMA mode<%d> sglen<%d> xfersz<%d>", dma->mode, dma->sglen, |
| host->xfer_size); |
| |
| msdc_dma_config(host, dma); |
| } |
| |
| static int msdc_do_request(struct mmc_host *mmc, struct mmc_request *mrq) |
| __must_hold(&host->lock) |
| { |
| struct msdc_host *host = mmc_priv(mmc); |
| struct mmc_command *cmd; |
| struct mmc_data *data; |
| void __iomem *base = host->base; |
| //u32 intsts = 0; |
| int read = 1, send_type = 0; |
| |
| #define SND_DAT 0 |
| #define SND_CMD 1 |
| |
| BUG_ON(mmc == NULL); |
| BUG_ON(mrq == NULL); |
| |
| host->error = 0; |
| |
| cmd = mrq->cmd; |
| data = mrq->cmd->data; |
| |
| #if 0 /* --- by chhung */ |
| //if(host->id ==1){ |
| N_MSG(OPS, "enable clock!"); |
| msdc_ungate_clock(host->id); |
| //} |
| #endif /* end of --- */ |
| |
| if (!data) { |
| send_type = SND_CMD; |
| if (msdc_do_command(host, cmd, 1, CMD_TIMEOUT) != 0) |
| goto done; |
| } else { |
| BUG_ON(data->blksz > HOST_MAX_BLKSZ); |
| send_type = SND_DAT; |
| |
| data->error = 0; |
| read = data->flags & MMC_DATA_READ ? 1 : 0; |
| host->data = data; |
| host->xfer_size = data->blocks * data->blksz; |
| host->blksz = data->blksz; |
| |
| if (read) { |
| if ((host->timeout_ns != data->timeout_ns) || |
| (host->timeout_clks != data->timeout_clks)) { |
| msdc_set_timeout(host, data->timeout_ns, data->timeout_clks); |
| } |
| } |
| |
| sdr_write32(SDC_BLK_NUM, data->blocks); |
| //msdc_clr_fifo(); /* no need */ |
| |
| msdc_dma_on(); /* enable DMA mode first!! */ |
| init_completion(&host->xfer_done); |
| |
| /* start the command first*/ |
| if (msdc_command_start(host, cmd, 1, CMD_TIMEOUT) != 0) |
| goto done; |
| |
| data->sg_count = dma_map_sg(mmc_dev(mmc), data->sg, |
| data->sg_len, |
| mmc_get_dma_dir(data)); |
| msdc_dma_setup(host, &host->dma, data->sg, |
| data->sg_count); |
| |
| /* then wait command done */ |
| if (msdc_command_resp(host, cmd, 1, CMD_TIMEOUT) != 0) |
| goto done; |
| |
| /* for read, the data coming too fast, then CRC error |
| start DMA no business with CRC. */ |
| //init_completion(&host->xfer_done); |
| msdc_dma_start(host); |
| |
| spin_unlock(&host->lock); |
| if (!wait_for_completion_timeout(&host->xfer_done, DAT_TIMEOUT)) { |
| ERR_MSG("XXX CMD<%d> wait xfer_done<%d> timeout!!", cmd->opcode, data->blocks * data->blksz); |
| ERR_MSG(" DMA_SA = 0x%x", sdr_read32(MSDC_DMA_SA)); |
| ERR_MSG(" DMA_CA = 0x%x", sdr_read32(MSDC_DMA_CA)); |
| ERR_MSG(" DMA_CTRL = 0x%x", sdr_read32(MSDC_DMA_CTRL)); |
| ERR_MSG(" DMA_CFG = 0x%x", sdr_read32(MSDC_DMA_CFG)); |
| data->error = -ETIMEDOUT; |
| |
| msdc_reset_hw(host); |
| msdc_clr_fifo(); |
| msdc_clr_int(); |
| } |
| spin_lock(&host->lock); |
| msdc_dma_stop(host); |
| |
| /* Last: stop transfer */ |
| if (data->stop) { |
| if (msdc_do_command(host, data->stop, 0, CMD_TIMEOUT) != 0) |
| goto done; |
| } |
| } |
| |
| done: |
| if (data != NULL) { |
| host->data = NULL; |
| dma_unmap_sg(mmc_dev(mmc), data->sg, data->sg_len, |
| mmc_get_dma_dir(data)); |
| host->blksz = 0; |
| |
| #if 0 // don't stop twice! |
| if (host->hw->flags & MSDC_REMOVABLE && data->error) { |
| msdc_abort_data(host); |
| /* reset in IRQ, stop command has issued. -> No need */ |
| } |
| #endif |
| |
| N_MSG(OPS, "CMD<%d> data<%s %s> blksz<%d> block<%d> error<%d>", cmd->opcode, (dma ? "dma" : "pio"), |
| (read ? "read " : "write"), data->blksz, data->blocks, data->error); |
| } |
| |
| #if 0 /* --- by chhung */ |
| #if 1 |
| //if(host->id==1) { |
| if (send_type == SND_CMD) { |
| if (cmd->opcode == MMC_SEND_STATUS) { |
| if ((cmd->resp[0] & CARD_READY_FOR_DATA) || (CARD_CURRENT_STATE(cmd->resp[0]) != 7)) { |
| N_MSG(OPS, "disable clock, CMD13 IDLE"); |
| msdc_gate_clock(host->id); |
| } |
| } else { |
| N_MSG(OPS, "disable clock, CMD<%d>", cmd->opcode); |
| msdc_gate_clock(host->id); |
| } |
| } else { |
| if (read) { |
| N_MSG(OPS, "disable clock!!! Read CMD<%d>", cmd->opcode); |
| msdc_gate_clock(host->id); |
| } |
| } |
| //} |
| #else |
| msdc_gate_clock(host->id); |
| #endif |
| #endif /* end of --- */ |
| |
| if (mrq->cmd->error) |
| host->error = 0x001; |
| if (mrq->data && mrq->data->error) |
| host->error |= 0x010; |
| if (mrq->stop && mrq->stop->error) |
| host->error |= 0x100; |
| |
| //if (host->error) ERR_MSG("host->error<%d>", host->error); |
| |
| return host->error; |
| } |
| |
| static int msdc_app_cmd(struct mmc_host *mmc, struct msdc_host *host) |
| { |
| struct mmc_command cmd; |
| struct mmc_request mrq; |
| u32 err; |
| |
| memset(&cmd, 0, sizeof(struct mmc_command)); |
| cmd.opcode = MMC_APP_CMD; |
| #if 0 /* bug: we meet mmc->card is null when ACMD6 */ |
| cmd.arg = mmc->card->rca << 16; |
| #else |
| cmd.arg = host->app_cmd_arg; |
| #endif |
| cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; |
| |
| memset(&mrq, 0, sizeof(struct mmc_request)); |
| mrq.cmd = &cmd; cmd.mrq = &mrq; |
| cmd.data = NULL; |
| |
| err = msdc_do_command(host, &cmd, 0, CMD_TIMEOUT); |
| return err; |
| } |
| |
| static int msdc_tune_cmdrsp(struct msdc_host *host, struct mmc_command *cmd) |
| { |
| int result = -1; |
| void __iomem *base = host->base; |
| u32 rsmpl, cur_rsmpl, orig_rsmpl; |
| u32 rrdly, cur_rrdly = 0xffffffff, orig_rrdly; |
| u32 skip = 1; |
| |
| /* ==== don't support 3.0 now ==== |
| 1: R_SMPL[1] |
| 2: PAD_CMD_RESP_RXDLY[26:22] |
| ==========================*/ |
| |
| // save the previous tune result |
| sdr_get_field(MSDC_IOCON, MSDC_IOCON_RSPL, &orig_rsmpl); |
| sdr_get_field(MSDC_PAD_TUNE, MSDC_PAD_TUNE_CMDRRDLY, &orig_rrdly); |
| |
| rrdly = 0; |
| do { |
| for (rsmpl = 0; rsmpl < 2; rsmpl++) { |
| /* Lv1: R_SMPL[1] */ |
| cur_rsmpl = (orig_rsmpl + rsmpl) % 2; |
| if (skip == 1) { |
| skip = 0; |
| continue; |
| } |
| sdr_set_field(MSDC_IOCON, MSDC_IOCON_RSPL, cur_rsmpl); |
| |
| if (host->app_cmd) { |
| result = msdc_app_cmd(host->mmc, host); |
| if (result) { |
| ERR_MSG("TUNE_CMD app_cmd<%d> failed: RESP_RXDLY<%d>,R_SMPL<%d>", |
| host->mrq->cmd->opcode, cur_rrdly, cur_rsmpl); |
| continue; |
| } |
| } |
| result = msdc_do_command(host, cmd, 0, CMD_TIMEOUT); // not tune. |
| ERR_MSG("TUNE_CMD<%d> %s PAD_CMD_RESP_RXDLY[26:22]<%d> R_SMPL[1]<%d>", cmd->opcode, |
| (result == 0) ? "PASS" : "FAIL", cur_rrdly, cur_rsmpl); |
| |
| if (result == 0) |
| return 0; |
| if (result != -EIO) { |
| ERR_MSG("TUNE_CMD<%d> Error<%d> not -EIO", cmd->opcode, result); |
| return result; |
| } |
| |
| /* should be EIO */ |
| if (sdr_read32(SDC_CMD) & 0x1800) { /* check if has data phase */ |
| msdc_abort_data(host); |
| } |
| } |
| |
| /* Lv2: PAD_CMD_RESP_RXDLY[26:22] */ |
| cur_rrdly = (orig_rrdly + rrdly + 1) % 32; |
| sdr_set_field(MSDC_PAD_TUNE, MSDC_PAD_TUNE_CMDRRDLY, cur_rrdly); |
| } while (++rrdly < 32); |
| |
| return result; |
| } |
| |
| /* Support SD2.0 Only */ |
| static int msdc_tune_bread(struct mmc_host *mmc, struct mmc_request *mrq) |
| { |
| struct msdc_host *host = mmc_priv(mmc); |
| void __iomem *base = host->base; |
| u32 ddr = 0; |
| u32 dcrc = 0; |
| u32 rxdly, cur_rxdly0, cur_rxdly1; |
| u32 dsmpl, cur_dsmpl, orig_dsmpl; |
| u32 cur_dat0, cur_dat1, cur_dat2, cur_dat3; |
| u32 cur_dat4, cur_dat5, cur_dat6, cur_dat7; |
| u32 orig_dat0, orig_dat1, orig_dat2, orig_dat3; |
| u32 orig_dat4, orig_dat5, orig_dat6, orig_dat7; |
| int result = -1; |
| u32 skip = 1; |
| |
| sdr_get_field(MSDC_IOCON, MSDC_IOCON_DSPL, &orig_dsmpl); |
| |
| /* Tune Method 2. */ |
| sdr_set_field(MSDC_IOCON, MSDC_IOCON_DDLSEL, 1); |
| |
| rxdly = 0; |
| do { |
| for (dsmpl = 0; dsmpl < 2; dsmpl++) { |
| cur_dsmpl = (orig_dsmpl + dsmpl) % 2; |
| if (skip == 1) { |
| skip = 0; |
| continue; |
| } |
| sdr_set_field(MSDC_IOCON, MSDC_IOCON_DSPL, cur_dsmpl); |
| |
| if (host->app_cmd) { |
| result = msdc_app_cmd(host->mmc, host); |
| if (result) { |
| ERR_MSG("TUNE_BREAD app_cmd<%d> failed", host->mrq->cmd->opcode); |
| continue; |
| } |
| } |
| result = msdc_do_request(mmc, mrq); |
| |
| sdr_get_field(SDC_DCRC_STS, |
| SDC_DCRC_STS_POS | SDC_DCRC_STS_NEG, |
| &dcrc); /* RO */ |
| if (!ddr) |
| dcrc &= ~SDC_DCRC_STS_NEG; |
| ERR_MSG("TUNE_BREAD<%s> dcrc<0x%x> DATRDDLY0/1<0x%x><0x%x> dsmpl<0x%x>", |
| (result == 0 && dcrc == 0) ? "PASS" : "FAIL", dcrc, |
| sdr_read32(MSDC_DAT_RDDLY0), sdr_read32(MSDC_DAT_RDDLY1), cur_dsmpl); |
| |
| /* Fix me: result is 0, but dcrc is still exist */ |
| if (result == 0 && dcrc == 0) { |
| goto done; |
| } else { |
| /* there is a case: command timeout, and data phase not processed */ |
| if (mrq->data->error != 0 && |
| mrq->data->error != -EIO) { |
| ERR_MSG("TUNE_READ: result<0x%x> cmd_error<%d> data_error<%d>", |
| result, mrq->cmd->error, mrq->data->error); |
| goto done; |
| } |
| } |
| } |
| |
| cur_rxdly0 = sdr_read32(MSDC_DAT_RDDLY0); |
| cur_rxdly1 = sdr_read32(MSDC_DAT_RDDLY1); |
| |
| /* E1 ECO. YD: Reverse */ |
| if (sdr_read32(MSDC_ECO_VER) >= 4) { |
| orig_dat0 = (cur_rxdly0 >> 24) & 0x1F; |
| orig_dat1 = (cur_rxdly0 >> 16) & 0x1F; |
| orig_dat2 = (cur_rxdly0 >> 8) & 0x1F; |
| orig_dat3 = (cur_rxdly0 >> 0) & 0x1F; |
| orig_dat4 = (cur_rxdly1 >> 24) & 0x1F; |
| orig_dat5 = (cur_rxdly1 >> 16) & 0x1F; |
| orig_dat6 = (cur_rxdly1 >> 8) & 0x1F; |
| orig_dat7 = (cur_rxdly1 >> 0) & 0x1F; |
| } else { |
| orig_dat0 = (cur_rxdly0 >> 0) & 0x1F; |
| orig_dat1 = (cur_rxdly0 >> 8) & 0x1F; |
| orig_dat2 = (cur_rxdly0 >> 16) & 0x1F; |
| orig_dat3 = (cur_rxdly0 >> 24) & 0x1F; |
| orig_dat4 = (cur_rxdly1 >> 0) & 0x1F; |
| orig_dat5 = (cur_rxdly1 >> 8) & 0x1F; |
| orig_dat6 = (cur_rxdly1 >> 16) & 0x1F; |
| orig_dat7 = (cur_rxdly1 >> 24) & 0x1F; |
| } |
| |
| if (ddr) { |
| cur_dat0 = (dcrc & (1 << 0) || dcrc & (1 << 8)) ? ((orig_dat0 + 1) % 32) : orig_dat0; |
| cur_dat1 = (dcrc & (1 << 1) || dcrc & (1 << 9)) ? ((orig_dat1 + 1) % 32) : orig_dat1; |
| cur_dat2 = (dcrc & (1 << 2) || dcrc & (1 << 10)) ? ((orig_dat2 + 1) % 32) : orig_dat2; |
| cur_dat3 = (dcrc & (1 << 3) || dcrc & (1 << 11)) ? ((orig_dat3 + 1) % 32) : orig_dat3; |
| } else { |
| cur_dat0 = (dcrc & (1 << 0)) ? ((orig_dat0 + 1) % 32) : orig_dat0; |
| cur_dat1 = (dcrc & (1 << 1)) ? ((orig_dat1 + 1) % 32) : orig_dat1; |
| cur_dat2 = (dcrc & (1 << 2)) ? ((orig_dat2 + 1) % 32) : orig_dat2; |
| cur_dat3 = (dcrc & (1 << 3)) ? ((orig_dat3 + 1) % 32) : orig_dat3; |
| } |
| cur_dat4 = (dcrc & (1 << 4)) ? ((orig_dat4 + 1) % 32) : orig_dat4; |
| cur_dat5 = (dcrc & (1 << 5)) ? ((orig_dat5 + 1) % 32) : orig_dat5; |
| cur_dat6 = (dcrc & (1 << 6)) ? ((orig_dat6 + 1) % 32) : orig_dat6; |
| cur_dat7 = (dcrc & (1 << 7)) ? ((orig_dat7 + 1) % 32) : orig_dat7; |
| |
| cur_rxdly0 = (cur_dat0 << 24) | (cur_dat1 << 16) | (cur_dat2 << 8) | (cur_dat3 << 0); |
| cur_rxdly1 = (cur_dat4 << 24) | (cur_dat5 << 16) | (cur_dat6 << 8) | (cur_dat7 << 0); |
| |
| sdr_write32(MSDC_DAT_RDDLY0, cur_rxdly0); |
| sdr_write32(MSDC_DAT_RDDLY1, cur_rxdly1); |
| |
| } while (++rxdly < 32); |
| |
| done: |
| return result; |
| } |
| |
| static int msdc_tune_bwrite(struct mmc_host *mmc, struct mmc_request *mrq) |
| { |
| struct msdc_host *host = mmc_priv(mmc); |
| void __iomem *base = host->base; |
| |
| u32 wrrdly, cur_wrrdly = 0xffffffff, orig_wrrdly; |
| u32 dsmpl, cur_dsmpl, orig_dsmpl; |
| u32 rxdly, cur_rxdly0; |
| u32 orig_dat0, orig_dat1, orig_dat2, orig_dat3; |
| u32 cur_dat0, cur_dat1, cur_dat2, cur_dat3; |
| int result = -1; |
| u32 skip = 1; |
| |
| // MSDC_IOCON_DDR50CKD need to check. [Fix me] |
| |
| sdr_get_field(MSDC_PAD_TUNE, MSDC_PAD_TUNE_DATWRDLY, &orig_wrrdly); |
| sdr_get_field(MSDC_IOCON, MSDC_IOCON_DSPL, &orig_dsmpl); |
| |
| /* Tune Method 2. just DAT0 */ |
| sdr_set_field(MSDC_IOCON, MSDC_IOCON_DDLSEL, 1); |
| cur_rxdly0 = sdr_read32(MSDC_DAT_RDDLY0); |
| |
| /* E1 ECO. YD: Reverse */ |
| if (sdr_read32(MSDC_ECO_VER) >= 4) { |
| orig_dat0 = (cur_rxdly0 >> 24) & 0x1F; |
| orig_dat1 = (cur_rxdly0 >> 16) & 0x1F; |
| orig_dat2 = (cur_rxdly0 >> 8) & 0x1F; |
| orig_dat3 = (cur_rxdly0 >> 0) & 0x1F; |
| } else { |
| orig_dat0 = (cur_rxdly0 >> 0) & 0x1F; |
| orig_dat1 = (cur_rxdly0 >> 8) & 0x1F; |
| orig_dat2 = (cur_rxdly0 >> 16) & 0x1F; |
| orig_dat3 = (cur_rxdly0 >> 24) & 0x1F; |
| } |
| |
| rxdly = 0; |
| do { |
| wrrdly = 0; |
| do { |
| for (dsmpl = 0; dsmpl < 2; dsmpl++) { |
| cur_dsmpl = (orig_dsmpl + dsmpl) % 2; |
| if (skip == 1) { |
| skip = 0; |
| continue; |
| } |
| sdr_set_field(MSDC_IOCON, MSDC_IOCON_DSPL, cur_dsmpl); |
| |
| if (host->app_cmd) { |
| result = msdc_app_cmd(host->mmc, host); |
| if (result) { |
| ERR_MSG("TUNE_BWRITE app_cmd<%d> failed", host->mrq->cmd->opcode); |
| continue; |
| } |
| } |
| result = msdc_do_request(mmc, mrq); |
| |
| ERR_MSG("TUNE_BWRITE<%s> DSPL<%d> DATWRDLY<%d> MSDC_DAT_RDDLY0<0x%x>", |
| result == 0 ? "PASS" : "FAIL", |
| cur_dsmpl, cur_wrrdly, cur_rxdly0); |
| |
| if (result == 0) { |
| goto done; |
| } else { |
| /* there is a case: command timeout, and data phase not processed */ |
| if (mrq->data->error != -EIO) { |
| ERR_MSG("TUNE_READ: result<0x%x> cmd_error<%d> data_error<%d>", |
| result, mrq->cmd->error, mrq->data->error); |
| goto done; |
| } |
| } |
| } |
| cur_wrrdly = (orig_wrrdly + wrrdly + 1) % 32; |
| sdr_set_field(MSDC_PAD_TUNE, MSDC_PAD_TUNE_DATWRDLY, cur_wrrdly); |
| } while (++wrrdly < 32); |
| |
| cur_dat0 = (orig_dat0 + rxdly) % 32; /* only adjust bit-1 for crc */ |
| cur_dat1 = orig_dat1; |
| cur_dat2 = orig_dat2; |
| cur_dat3 = orig_dat3; |
| |
| cur_rxdly0 = (cur_dat0 << 24) | (cur_dat1 << 16) | (cur_dat2 << 8) | (cur_dat3 << 0); |
| sdr_write32(MSDC_DAT_RDDLY0, cur_rxdly0); |
| } while (++rxdly < 32); |
| |
| done: |
| return result; |
| } |
| |
| static int msdc_get_card_status(struct mmc_host *mmc, struct msdc_host *host, u32 *status) |
| { |
| struct mmc_command cmd; |
| struct mmc_request mrq; |
| u32 err; |
| |
| memset(&cmd, 0, sizeof(struct mmc_command)); |
| cmd.opcode = MMC_SEND_STATUS; |
| if (mmc->card) { |
| cmd.arg = mmc->card->rca << 16; |
| } else { |
| ERR_MSG("cmd13 mmc card is null"); |
| cmd.arg = host->app_cmd_arg; |
| } |
| cmd.flags = MMC_RSP_SPI_R2 | MMC_RSP_R1 | MMC_CMD_AC; |
| |
| memset(&mrq, 0, sizeof(struct mmc_request)); |
| mrq.cmd = &cmd; cmd.mrq = &mrq; |
| cmd.data = NULL; |
| |
| err = msdc_do_command(host, &cmd, 1, CMD_TIMEOUT); |
| |
| if (status) |
| *status = cmd.resp[0]; |
| |
| return err; |
| } |
| |
| static int msdc_check_busy(struct mmc_host *mmc, struct msdc_host *host) |
| { |
| u32 err = 0; |
| u32 status = 0; |
| |
| do { |
| err = msdc_get_card_status(mmc, host, &status); |
| if (err) |
| return err; |
| /* need cmd12? */ |
| ERR_MSG("cmd<13> resp<0x%x>", status); |
| } while (R1_CURRENT_STATE(status) == 7); |
| |
| return err; |
| } |
| |
| /* failed when msdc_do_request */ |
| static int msdc_tune_request(struct mmc_host *mmc, struct mmc_request *mrq) |
| { |
| struct msdc_host *host = mmc_priv(mmc); |
| struct mmc_command *cmd; |
| struct mmc_data *data; |
| //u32 base = host->base; |
| int ret = 0, read; |
| |
| cmd = mrq->cmd; |
| data = mrq->cmd->data; |
| |
| read = data->flags & MMC_DATA_READ ? 1 : 0; |
| |
| if (read) { |
| if (data->error == -EIO) |
| ret = msdc_tune_bread(mmc, mrq); |
| } else { |
| ret = msdc_check_busy(mmc, host); |
| if (ret) { |
| ERR_MSG("XXX cmd13 wait program done failed"); |
| return ret; |
| } |
| /* CRC and TO */ |
| /* Fix me: don't care card status? */ |
| ret = msdc_tune_bwrite(mmc, mrq); |
| } |
| |
| return ret; |
| } |
| |
| /* ops.request */ |
| static void msdc_ops_request(struct mmc_host *mmc, struct mmc_request *mrq) |
| { |
| struct msdc_host *host = mmc_priv(mmc); |
| |
| //=== for sdio profile === |
| #if 0 /* --- by chhung */ |
| u32 old_H32, old_L32, new_H32, new_L32; |
| u32 ticks = 0, opcode = 0, sizes = 0, bRx = 0; |
| #endif /* end of --- */ |
| |
| WARN_ON(host->mrq); |
| |
| /* start to process */ |
| spin_lock(&host->lock); |
| #if 0 /* --- by chhung */ |
| if (sdio_pro_enable) { //=== for sdio profile === |
| if (mrq->cmd->opcode == 52 || mrq->cmd->opcode == 53) |
| GPT_GetCounter64(&old_L32, &old_H32); |
| } |
| #endif /* end of --- */ |
| |
| host->mrq = mrq; |
| |
| if (msdc_do_request(mmc, mrq)) { |
| if (host->hw->flags & MSDC_REMOVABLE && ralink_soc == MT762X_SOC_MT7621AT && mrq->data && mrq->data->error) |
| msdc_tune_request(mmc, mrq); |
| } |
| |
| /* ==== when request done, check if app_cmd ==== */ |
| if (mrq->cmd->opcode == MMC_APP_CMD) { |
| host->app_cmd = 1; |
| host->app_cmd_arg = mrq->cmd->arg; /* save the RCA */ |
| } else { |
| host->app_cmd = 0; |
| //host->app_cmd_arg = 0; |
| } |
| |
| host->mrq = NULL; |
| |
| #if 0 /* --- by chhung */ |
| //=== for sdio profile === |
| if (sdio_pro_enable) { |
| if (mrq->cmd->opcode == 52 || mrq->cmd->opcode == 53) { |
| GPT_GetCounter64(&new_L32, &new_H32); |
| ticks = msdc_time_calc(old_L32, old_H32, new_L32, new_H32); |
| |
| opcode = mrq->cmd->opcode; |
| if (mrq->cmd->data) { |
| sizes = mrq->cmd->data->blocks * mrq->cmd->data->blksz; |
| bRx = mrq->cmd->data->flags & MMC_DATA_READ ? 1 : 0; |
| } else { |
| bRx = mrq->cmd->arg & 0x80000000 ? 1 : 0; |
| } |
| |
| if (!mrq->cmd->error) |
| msdc_performance(opcode, sizes, bRx, ticks); |
| } |
| } |
| #endif /* end of --- */ |
| spin_unlock(&host->lock); |
| |
| mmc_request_done(mmc, mrq); |
| |
| return; |
| } |
| |
| /* called by ops.set_ios */ |
| static void msdc_set_buswidth(struct msdc_host *host, u32 width) |
| { |
| void __iomem *base = host->base; |
| u32 val = sdr_read32(SDC_CFG); |
| |
| val &= ~SDC_CFG_BUSWIDTH; |
| |
| switch (width) { |
| default: |
| case MMC_BUS_WIDTH_1: |
| width = 1; |
| val |= (MSDC_BUS_1BITS << 16); |
| break; |
| case MMC_BUS_WIDTH_4: |
| val |= (MSDC_BUS_4BITS << 16); |
| break; |
| case MMC_BUS_WIDTH_8: |
| val |= (MSDC_BUS_8BITS << 16); |
| break; |
| } |
| |
| sdr_write32(SDC_CFG, val); |
| |
| N_MSG(CFG, "Bus Width = %d", width); |
| } |
| |
| /* ops.set_ios */ |
| static void msdc_ops_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) |
| { |
| struct msdc_host *host = mmc_priv(mmc); |
| void __iomem *base = host->base; |
| u32 ddr = 0; |
| |
| #ifdef MT6575_SD_DEBUG |
| static char *vdd[] = { |
| "1.50v", "1.55v", "1.60v", "1.65v", "1.70v", "1.80v", "1.90v", |
| "2.00v", "2.10v", "2.20v", "2.30v", "2.40v", "2.50v", "2.60v", |
| "2.70v", "2.80v", "2.90v", "3.00v", "3.10v", "3.20v", "3.30v", |
| "3.40v", "3.50v", "3.60v" |
| }; |
| static char *power_mode[] = { |
| "OFF", "UP", "ON" |
| }; |
| static char *bus_mode[] = { |
| "UNKNOWN", "OPENDRAIN", "PUSHPULL" |
| }; |
| static char *timing[] = { |
| "LEGACY", "MMC_HS", "SD_HS" |
| }; |
| |
| printk("SET_IOS: CLK(%dkHz), BUS(%s), BW(%u), PWR(%s), VDD(%s), TIMING(%s)", |
| ios->clock / 1000, bus_mode[ios->bus_mode], |
| (ios->bus_width == MMC_BUS_WIDTH_4) ? 4 : 1, |
| power_mode[ios->power_mode], vdd[ios->vdd], timing[ios->timing]); |
| #endif |
| |
| msdc_set_buswidth(host, ios->bus_width); |
| |
| /* Power control ??? */ |
| switch (ios->power_mode) { |
| case MMC_POWER_OFF: |
| case MMC_POWER_UP: |
| // msdc_set_power_mode(host, ios->power_mode); /* --- by chhung */ |
| break; |
| case MMC_POWER_ON: |
| host->power_mode = MMC_POWER_ON; |
| break; |
| default: |
| break; |
| } |
| |
| /* Clock control */ |
| if (host->mclk != ios->clock) { |
| if (ios->clock > 25000000) { |
| //if (!(host->hw->flags & MSDC_REMOVABLE)) { |
| INIT_MSG("SD data latch edge<%d>", MSDC_SMPL_FALLING); |
| sdr_set_field(MSDC_IOCON, MSDC_IOCON_RSPL, |
| MSDC_SMPL_FALLING); |
| sdr_set_field(MSDC_IOCON, MSDC_IOCON_DSPL, |
| MSDC_SMPL_FALLING); |
| //} /* for tuning debug */ |
| } else { /* default value */ |
| sdr_write32(MSDC_IOCON, 0x00000000); |
| // sdr_write32(MSDC_DAT_RDDLY0, 0x00000000); |
| sdr_write32(MSDC_DAT_RDDLY0, 0x10101010); // for MT7620 E2 and afterward |
| sdr_write32(MSDC_DAT_RDDLY1, 0x00000000); |
| // sdr_write32(MSDC_PAD_TUNE, 0x00000000); |
| sdr_write32(MSDC_PAD_TUNE, 0x84101010); // for MT7620 E2 and afterward |
| } |
| msdc_set_mclk(host, ddr, ios->clock); |
| } |
| } |
| |
| /* ops.get_ro */ |
| static int msdc_ops_get_ro(struct mmc_host *mmc) |
| { |
| struct msdc_host *host = mmc_priv(mmc); |
| void __iomem *base = host->base; |
| unsigned long flags; |
| int ro = 0; |
| |
| if (host->hw->flags & MSDC_WP_PIN_EN) { /* set for card */ |
| spin_lock_irqsave(&host->lock, flags); |
| ro = (sdr_read32(MSDC_PS) >> 31); |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| return ro; |
| } |
| |
| /* ops.get_cd */ |
| static int msdc_ops_get_cd(struct mmc_host *mmc) |
| { |
| struct msdc_host *host = mmc_priv(mmc); |
| void __iomem *base = host->base; |
| unsigned long flags; |
| int present = 1; |
| |
| /* for sdio, MSDC_REMOVABLE not set, always return 1 */ |
| if (!(host->hw->flags & MSDC_REMOVABLE)) { |
| /* For sdio, read H/W always get<1>, but may timeout some times */ |
| #if 1 |
| host->card_inserted = 1; |
| return 1; |
| #else |
| host->card_inserted = (host->pm_state.event == PM_EVENT_USER_RESUME) ? 1 : 0; |
| INIT_MSG("sdio ops_get_cd<%d>", host->card_inserted); |
| return host->card_inserted; |
| #endif |
| } |
| |
| /* MSDC_CD_PIN_EN set for card */ |
| if (host->hw->flags & MSDC_CD_PIN_EN) { |
| spin_lock_irqsave(&host->lock, flags); |
| #if 0 |
| present = host->card_inserted; /* why not read from H/W: Fix me*/ |
| #else |
| // CD |
| if (cd_active_low) |
| present = (sdr_read32(MSDC_PS) & MSDC_PS_CDSTS) ? 0 : 1; |
| else |
| present = (sdr_read32(MSDC_PS) & MSDC_PS_CDSTS) ? 1 : 0; |
| host->card_inserted = present; |
| #endif |
| spin_unlock_irqrestore(&host->lock, flags); |
| } else { |
| present = 0; /* TODO? Check DAT3 pins for card detection */ |
| } |
| |
| INIT_MSG("ops_get_cd return<%d>", present); |
| return present; |
| } |
| |
| static struct mmc_host_ops mt_msdc_ops = { |
| .request = msdc_ops_request, |
| .set_ios = msdc_ops_set_ios, |
| .get_ro = msdc_ops_get_ro, |
| .get_cd = msdc_ops_get_cd, |
| }; |
| |
| /*--------------------------------------------------------------------------*/ |
| /* interrupt handler */ |
| /*--------------------------------------------------------------------------*/ |
| static irqreturn_t msdc_irq(int irq, void *dev_id) |
| { |
| struct msdc_host *host = (struct msdc_host *)dev_id; |
| struct mmc_data *data = host->data; |
| struct mmc_command *cmd = host->cmd; |
| void __iomem *base = host->base; |
| |
| u32 cmdsts = MSDC_INT_RSPCRCERR | MSDC_INT_CMDTMO | MSDC_INT_CMDRDY | |
| MSDC_INT_ACMDCRCERR | MSDC_INT_ACMDTMO | MSDC_INT_ACMDRDY | |
| MSDC_INT_ACMD19_DONE; |
| u32 datsts = MSDC_INT_DATCRCERR | MSDC_INT_DATTMO; |
| |
| u32 intsts = sdr_read32(MSDC_INT); |
| u32 inten = sdr_read32(MSDC_INTEN); inten &= intsts; |
| |
| sdr_write32(MSDC_INT, intsts); /* clear interrupts */ |
| /* MSG will cause fatal error */ |
| |
| /* card change interrupt */ |
| if (intsts & MSDC_INT_CDSC) { |
| if (host->mmc->caps & MMC_CAP_NEEDS_POLL) |
| return IRQ_HANDLED; |
| IRQ_MSG("MSDC_INT_CDSC irq<0x%.8x>", intsts); |
| schedule_delayed_work(&host->card_delaywork, HZ); |
| /* tuning when plug card ? */ |
| } |
| |
| /* sdio interrupt */ |
| if (intsts & MSDC_INT_SDIOIRQ) { |
| IRQ_MSG("XXX MSDC_INT_SDIOIRQ"); /* seems not sdio irq */ |
| //mmc_signal_sdio_irq(host->mmc); |
| } |
| |
| /* transfer complete interrupt */ |
| if (data != NULL) { |
| if (inten & MSDC_INT_XFER_COMPL) { |
| data->bytes_xfered = host->xfer_size; |
| complete(&host->xfer_done); |
| } |
| |
| if (intsts & datsts) { |
| /* do basic reset, or stop command will sdc_busy */ |
| msdc_reset_hw(host); |
| msdc_clr_fifo(); |
| msdc_clr_int(); |
| |
| if (intsts & MSDC_INT_DATTMO) { |
| IRQ_MSG("XXX CMD<%d> MSDC_INT_DATTMO", host->mrq->cmd->opcode); |
| data->error = -ETIMEDOUT; |
| } else if (intsts & MSDC_INT_DATCRCERR) { |
| IRQ_MSG("XXX CMD<%d> MSDC_INT_DATCRCERR, SDC_DCRC_STS<0x%x>", host->mrq->cmd->opcode, sdr_read32(SDC_DCRC_STS)); |
| data->error = -EIO; |
| } |
| |
| //if(sdr_read32(MSDC_INTEN) & MSDC_INT_XFER_COMPL) { |
| complete(&host->xfer_done); /* Read CRC come fast, XFER_COMPL not enabled */ |
| } |
| } |
| |
| /* command interrupts */ |
| if ((cmd != NULL) && (intsts & cmdsts)) { |
| if ((intsts & MSDC_INT_CMDRDY) || (intsts & MSDC_INT_ACMDRDY) || |
| (intsts & MSDC_INT_ACMD19_DONE)) { |
| u32 *rsp = &cmd->resp[0]; |
| |
| switch (host->cmd_rsp) { |
| case RESP_NONE: |
| break; |
| case RESP_R2: |
| *rsp++ = sdr_read32(SDC_RESP3); *rsp++ = sdr_read32(SDC_RESP2); |
| *rsp++ = sdr_read32(SDC_RESP1); *rsp++ = sdr_read32(SDC_RESP0); |
| break; |
| default: /* Response types 1, 3, 4, 5, 6, 7(1b) */ |
| if ((intsts & MSDC_INT_ACMDRDY) || (intsts & MSDC_INT_ACMD19_DONE)) |
| *rsp = sdr_read32(SDC_ACMD_RESP); |
| else |
| *rsp = sdr_read32(SDC_RESP0); |
| break; |
| } |
| } else if ((intsts & MSDC_INT_RSPCRCERR) || (intsts & MSDC_INT_ACMDCRCERR)) { |
| if (intsts & MSDC_INT_ACMDCRCERR) |
| IRQ_MSG("XXX CMD<%d> MSDC_INT_ACMDCRCERR", cmd->opcode); |
| else |
| IRQ_MSG("XXX CMD<%d> MSDC_INT_RSPCRCERR", cmd->opcode); |
| cmd->error = -EIO; |
| } else if ((intsts & MSDC_INT_CMDTMO) || (intsts & MSDC_INT_ACMDTMO)) { |
| if (intsts & MSDC_INT_ACMDTMO) |
| IRQ_MSG("XXX CMD<%d> MSDC_INT_ACMDTMO", cmd->opcode); |
| else |
| IRQ_MSG("XXX CMD<%d> MSDC_INT_CMDTMO", cmd->opcode); |
| cmd->error = -ETIMEDOUT; |
| msdc_reset_hw(host); |
| msdc_clr_fifo(); |
| msdc_clr_int(); |
| } |
| complete(&host->cmd_done); |
| } |
| |
| /* mmc irq interrupts */ |
| if (intsts & MSDC_INT_MMCIRQ) |
| printk(KERN_INFO "msdc[%d] MMCIRQ: SDC_CSTS=0x%.8x\r\n", host->id, sdr_read32(SDC_CSTS)); |
| |
| #ifdef MT6575_SD_DEBUG |
| { |
| /* msdc_int_reg *int_reg = (msdc_int_reg*)&intsts;*/ |
| N_MSG(INT, "IRQ_EVT(0x%x): MMCIRQ(%d) CDSC(%d), ACRDY(%d), ACTMO(%d), ACCRE(%d) AC19DN(%d)", |
| intsts, |
| int_reg->mmcirq, |
| int_reg->cdsc, |
| int_reg->atocmdrdy, |
| int_reg->atocmdtmo, |
| int_reg->atocmdcrc, |
| int_reg->atocmd19done); |
| N_MSG(INT, "IRQ_EVT(0x%x): SDIO(%d) CMDRDY(%d), CMDTMO(%d), RSPCRC(%d), CSTA(%d)", |
| intsts, |
| int_reg->sdioirq, |
| int_reg->cmdrdy, |
| int_reg->cmdtmo, |
| int_reg->rspcrc, |
| int_reg->csta); |
| N_MSG(INT, "IRQ_EVT(0x%x): XFCMP(%d) DXDONE(%d), DATTMO(%d), DATCRC(%d), DMAEMP(%d)", |
| intsts, |
| int_reg->xfercomp, |
| int_reg->dxferdone, |
| int_reg->dattmo, |
| int_reg->datcrc, |
| int_reg->dmaqempty); |
| } |
| #endif |
| |
| return IRQ_HANDLED; |
| } |
| |
| /*--------------------------------------------------------------------------*/ |
| /* platform_driver members */ |
| /*--------------------------------------------------------------------------*/ |
| /* called by msdc_drv_probe/remove */ |
| static void msdc_enable_cd_irq(struct msdc_host *host, int enable) |
| { |
| struct msdc_hw *hw = host->hw; |
| void __iomem *base = host->base; |
| |
| /* for sdio, not set */ |
| if ((hw->flags & MSDC_CD_PIN_EN) == 0) { |
| /* Pull down card detection pin since it is not avaiable */ |
| /* |
| if (hw->config_gpio_pin) |
| hw->config_gpio_pin(MSDC_CD_PIN, GPIO_PULL_DOWN); |
| */ |
| sdr_clr_bits(MSDC_PS, MSDC_PS_CDEN); |
| sdr_clr_bits(MSDC_INTEN, MSDC_INTEN_CDSC); |
| sdr_clr_bits(SDC_CFG, SDC_CFG_INSWKUP); |
| return; |
| } |
| |
| N_MSG(CFG, "CD IRQ Enable(%d)", enable); |
| |
| if (enable) { |
| /* card detection circuit relies on the core power so that the core power |
| * shouldn't be turned off. Here adds a reference count to keep |
| * the core power alive. |
| */ |
| //msdc_vcore_on(host); //did in msdc_init_hw() |
| |
| if (hw->config_gpio_pin) /* NULL */ |
| hw->config_gpio_pin(MSDC_CD_PIN, GPIO_PULL_UP); |
| |
| sdr_set_field(MSDC_PS, MSDC_PS_CDDEBOUNCE, DEFAULT_DEBOUNCE); |
| sdr_set_bits(MSDC_PS, MSDC_PS_CDEN); |
| sdr_set_bits(MSDC_INTEN, MSDC_INTEN_CDSC); |
| sdr_set_bits(SDC_CFG, SDC_CFG_INSWKUP); /* not in document! Fix me */ |
| } else { |
| if (hw->config_gpio_pin) /* NULL */ |
| hw->config_gpio_pin(MSDC_CD_PIN, GPIO_PULL_DOWN); |
| |
| sdr_clr_bits(SDC_CFG, SDC_CFG_INSWKUP); |
| sdr_clr_bits(MSDC_PS, MSDC_PS_CDEN); |
| sdr_clr_bits(MSDC_INTEN, MSDC_INTEN_CDSC); |
| |
| /* Here decreases a reference count to core power since card |
| * detection circuit is shutdown. |
| */ |
| //msdc_vcore_off(host); |
| } |
| } |
| |
| /* called by msdc_drv_probe */ |
| static void msdc_init_hw(struct msdc_host *host) |
| { |
| void __iomem *base = host->base; |
| |
| /* Power on */ |
| #if 0 /* --- by chhung */ |
| msdc_vcore_on(host); |
| msdc_pin_reset(host, MSDC_PIN_PULL_UP); |
| msdc_select_clksrc(host, hw->clk_src); |
| enable_clock(PERI_MSDC0_PDN + host->id, "SD"); |
| msdc_vdd_on(host); |
| #endif /* end of --- */ |
| /* Configure to MMC/SD mode */ |
| sdr_set_field(MSDC_CFG, MSDC_CFG_MODE, MSDC_SDMMC); |
| |
| /* Reset */ |
| msdc_reset_hw(host); |
| msdc_clr_fifo(); |
| |
| /* Disable card detection */ |
| sdr_clr_bits(MSDC_PS, MSDC_PS_CDEN); |
| |
| /* Disable and clear all interrupts */ |
| sdr_clr_bits(MSDC_INTEN, sdr_read32(MSDC_INTEN)); |
| sdr_write32(MSDC_INT, sdr_read32(MSDC_INT)); |
| |
| #if 1 |
| /* reset tuning parameter */ |
| sdr_write32(MSDC_PAD_CTL0, 0x00090000); |
| sdr_write32(MSDC_PAD_CTL1, 0x000A0000); |
| sdr_write32(MSDC_PAD_CTL2, 0x000A0000); |
| // sdr_write32(MSDC_PAD_TUNE, 0x00000000); |
| sdr_write32(MSDC_PAD_TUNE, 0x84101010); // for MT7620 E2 and afterward |
| // sdr_write32(MSDC_DAT_RDDLY0, 0x00000000); |
| sdr_write32(MSDC_DAT_RDDLY0, 0x10101010); // for MT7620 E2 and afterward |
| sdr_write32(MSDC_DAT_RDDLY1, 0x00000000); |
| sdr_write32(MSDC_IOCON, 0x00000000); |
| #if 0 // use MT7620 default value: 0x403c004f |
| sdr_write32(MSDC_PATCH_BIT0, 0x003C000F); /* bit0 modified: Rx Data Clock Source: 1 -> 2.0*/ |
| #endif |
| |
| if (sdr_read32(MSDC_ECO_VER) >= 4) { |
| if (host->id == 1) { |
| sdr_set_field(MSDC_PATCH_BIT1, MSDC_PATCH_BIT1_WRDAT_CRCS, 1); |
| sdr_set_field(MSDC_PATCH_BIT1, MSDC_PATCH_BIT1_CMD_RSP, 1); |
| |
| /* internal clock: latch read data */ |
| sdr_set_bits(MSDC_PATCH_BIT0, MSDC_PATCH_BIT_CKGEN_CK); |
| } |
| } |
| #endif |
| |
| /* for safety, should clear SDC_CFG.SDIO_INT_DET_EN & set SDC_CFG.SDIO in |
| pre-loader,uboot,kernel drivers. and SDC_CFG.SDIO_INT_DET_EN will be only |
| set when kernel driver wants to use SDIO bus interrupt */ |
| /* Configure to enable SDIO mode. it's must otherwise sdio cmd5 failed */ |
| sdr_set_bits(SDC_CFG, SDC_CFG_SDIO); |
| |
| /* disable detect SDIO device interupt function */ |
| sdr_clr_bits(SDC_CFG, SDC_CFG_SDIOIDE); |
| |
| /* eneable SMT for glitch filter */ |
| sdr_set_bits(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKSMT); |
| sdr_set_bits(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDSMT); |
| sdr_set_bits(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATSMT); |
| |
| #if 1 |
| /* set clk, cmd, dat pad driving */ |
| sdr_set_field(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKDRVN, 4); |
| sdr_set_field(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKDRVP, 4); |
| sdr_set_field(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDDRVN, 4); |
| sdr_set_field(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDDRVP, 4); |
| sdr_set_field(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATDRVN, 4); |
| sdr_set_field(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATDRVP, 4); |
| #else |
| sdr_set_field(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKDRVN, 0); |
| sdr_set_field(MSDC_PAD_CTL0, MSDC_PAD_CTL0_CLKDRVP, 0); |
| sdr_set_field(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDDRVN, 0); |
| sdr_set_field(MSDC_PAD_CTL1, MSDC_PAD_CTL1_CMDDRVP, 0); |
| sdr_set_field(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATDRVN, 0); |
| sdr_set_field(MSDC_PAD_CTL2, MSDC_PAD_CTL2_DATDRVP, 0); |
| #endif |
| |
| /* set sampling edge */ |
| |
| /* write crc timeout detection */ |
| sdr_set_field(MSDC_PATCH_BIT0, 1 << 30, 1); |
| |
| /* Configure to default data timeout */ |
| sdr_set_field(SDC_CFG, SDC_CFG_DTOC, DEFAULT_DTOC); |
| |
| msdc_set_buswidth(host, MMC_BUS_WIDTH_1); |
| |
| N_MSG(FUC, "init hardware done!"); |
| } |
| |
| /* called by msdc_drv_remove */ |
| static void msdc_deinit_hw(struct msdc_host *host) |
| { |
| void __iomem *base = host->base; |
| |
| /* Disable and clear all interrupts */ |
| sdr_clr_bits(MSDC_INTEN, sdr_read32(MSDC_INTEN)); |
| sdr_write32(MSDC_INT, sdr_read32(MSDC_INT)); |
| |
| /* Disable card detection */ |
| msdc_enable_cd_irq(host, 0); |
| // msdc_set_power_mode(host, MMC_POWER_OFF); /* make sure power down */ /* --- by chhung */ |
| } |
| |
| /* init gpd and bd list in msdc_drv_probe */ |
| static void msdc_init_gpd_bd(struct msdc_host *host, struct msdc_dma *dma) |
| { |
| struct gpd *gpd = dma->gpd; |
| struct bd *bd = dma->bd; |
| int i; |
| |
| /* we just support one gpd, but gpd->next must be set for desc |
| * DMA. That's why we alloc 2 gpd structurs. |
| */ |
| |
| memset(gpd, 0, sizeof(struct gpd) * 2); |
| |
| gpd->bdp = 1; /* hwo, cs, bd pointer */ |
| gpd->ptr = (void *)dma->bd_addr; /* physical address */ |
| gpd->next = (void *)((u32)dma->gpd_addr + sizeof(struct gpd)); |
| |
| memset(bd, 0, sizeof(struct bd) * MAX_BD_NUM); |
| for (i = 0; i < (MAX_BD_NUM - 1); i++) |
| bd[i].next = (void *)(dma->bd_addr + sizeof(*bd) * (i + 1)); |
| } |
| |
| static int msdc_drv_probe(struct platform_device *pdev) |
| { |
| struct resource *res; |
| __iomem void *base; |
| struct mmc_host *mmc; |
| struct msdc_host *host; |
| struct msdc_hw *hw; |
| int ret; |
| |
| hw = &msdc0_hw; |
| |
| if (of_property_read_bool(pdev->dev.of_node, "mtk,wp-en")) |
| msdc0_hw.flags |= MSDC_WP_PIN_EN; |
| |
| /* Allocate MMC host for this device */ |
| mmc = mmc_alloc_host(sizeof(struct msdc_host), &pdev->dev); |
| if (!mmc) |
| return -ENOMEM; |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| base = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(base)) { |
| ret = PTR_ERR(base); |
| goto host_free; |
| } |
| |
| /* Set host parameters to mmc */ |
| mmc->ops = &mt_msdc_ops; |
| mmc->f_min = HOST_MIN_MCLK; |
| mmc->f_max = HOST_MAX_MCLK; |
| mmc->ocr_avail = MSDC_OCR_AVAIL; |
| |
| mmc->caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED; |
| |
| //TODO: read this as bus-width from dt (via mmc_of_parse) |
| mmc->caps |= MMC_CAP_4_BIT_DATA; |
| |
| cd_active_low = !of_property_read_bool(pdev->dev.of_node, "mediatek,cd-high"); |
| |
| if (of_property_read_bool(pdev->dev.of_node, "mediatek,cd-poll")) |
| mmc->caps |= MMC_CAP_NEEDS_POLL; |
| |
| /* MMC core transfer sizes tunable parameters */ |
| mmc->max_segs = MAX_HW_SGMTS; |
| |
| mmc->max_seg_size = MAX_SGMT_SZ; |
| mmc->max_blk_size = HOST_MAX_BLKSZ; |
| mmc->max_req_size = MAX_REQ_SZ; |
| mmc->max_blk_count = mmc->max_req_size; |
| |
| host = mmc_priv(mmc); |
| host->hw = hw; |
| host->mmc = mmc; |
| host->id = pdev->id; |
| if (host->id < 0 || host->id >= 4) |
| host->id = 0; |
| host->error = 0; |
| |
| host->irq = platform_get_irq(pdev, 0); |
| if (host->irq < 0) { |
| ret = -EINVAL; |
| goto host_free; |
| } |
| |
| host->base = base; |
| host->mclk = 0; /* mclk: the request clock of mmc sub-system */ |
| host->hclk = hclks[hw->clk_src]; /* hclk: clock of clock source to msdc controller */ |
| host->sclk = 0; /* sclk: the really clock after divition */ |
| host->pm_state = PMSG_RESUME; |
| host->suspend = 0; |
| host->core_clkon = 0; |
| host->card_clkon = 0; |
| host->core_power = 0; |
| host->power_mode = MMC_POWER_OFF; |
| // host->card_inserted = hw->flags & MSDC_REMOVABLE ? 0 : 1; |
| host->timeout_ns = 0; |
| host->timeout_clks = DEFAULT_DTOC * 65536; |
| |
| host->mrq = NULL; |
| //init_MUTEX(&host->sem); /* we don't need to support multiple threads access */ |
| |
| mmc_dev(mmc)->dma_mask = NULL; |
| |
| /* using dma_alloc_coherent*/ /* todo: using 1, for all 4 slots */ |
| host->dma.gpd = dma_alloc_coherent(&pdev->dev, |
| MAX_GPD_NUM * sizeof(struct gpd), |
| &host->dma.gpd_addr, GFP_KERNEL); |
| host->dma.bd = dma_alloc_coherent(&pdev->dev, |
| MAX_BD_NUM * sizeof(struct bd), |
| &host->dma.bd_addr, GFP_KERNEL); |
| if (!host->dma.gpd || !host->dma.bd) { |
| ret = -ENOMEM; |
| goto release_mem; |
| } |
| msdc_init_gpd_bd(host, &host->dma); |
| |
| INIT_DELAYED_WORK(&host->card_delaywork, msdc_tasklet_card); |
| spin_lock_init(&host->lock); |
| msdc_init_hw(host); |
| |
| /* TODO check weather flags 0 is correct, the mtk-sd driver uses |
| * IRQF_TRIGGER_LOW | IRQF_ONESHOT for flags |
| * |
| * for flags 0 the trigger polarity is determined by the |
| * device tree, but not the oneshot flag, but maybe it is also |
| * not needed because the soc could be oneshot safe. |
| */ |
| ret = devm_request_irq(&pdev->dev, host->irq, msdc_irq, 0, pdev->name, |
| host); |
| if (ret) |
| goto release; |
| |
| platform_set_drvdata(pdev, mmc); |
| |
| ret = mmc_add_host(mmc); |
| if (ret) |
| goto release; |
| |
| /* Config card detection pin and enable interrupts */ |
| if (hw->flags & MSDC_CD_PIN_EN) { /* set for card */ |
| msdc_enable_cd_irq(host, 1); |
| } else { |
| msdc_enable_cd_irq(host, 0); |
| } |
| |
| return 0; |
| |
| release: |
| platform_set_drvdata(pdev, NULL); |
| msdc_deinit_hw(host); |
| cancel_delayed_work_sync(&host->card_delaywork); |
| |
| release_mem: |
| if (host->dma.gpd) |
| dma_free_coherent(&pdev->dev, MAX_GPD_NUM * sizeof(struct gpd), |
| host->dma.gpd, host->dma.gpd_addr); |
| if (host->dma.bd) |
| dma_free_coherent(&pdev->dev, MAX_BD_NUM * sizeof(struct bd), |
| host->dma.bd, host->dma.bd_addr); |
| host_free: |
| mmc_free_host(mmc); |
| |
| return ret; |
| } |
| |
| /* 4 device share one driver, using "drvdata" to show difference */ |
| static int msdc_drv_remove(struct platform_device *pdev) |
| { |
| struct mmc_host *mmc; |
| struct msdc_host *host; |
| |
| mmc = platform_get_drvdata(pdev); |
| BUG_ON(!mmc); |
| |
| host = mmc_priv(mmc); |
| BUG_ON(!host); |
| |
| ERR_MSG("removed !!!"); |
| |
| platform_set_drvdata(pdev, NULL); |
| mmc_remove_host(host->mmc); |
| msdc_deinit_hw(host); |
| |
| cancel_delayed_work_sync(&host->card_delaywork); |
| |
| dma_free_coherent(&pdev->dev, MAX_GPD_NUM * sizeof(struct gpd), |
| host->dma.gpd, host->dma.gpd_addr); |
| dma_free_coherent(&pdev->dev, MAX_BD_NUM * sizeof(struct bd), |
| host->dma.bd, host->dma.bd_addr); |
| |
| mmc_free_host(host->mmc); |
| |
| return 0; |
| } |
| |
| /* Fix me: Power Flow */ |
| #ifdef CONFIG_PM |
| |
| static void msdc_drv_pm(struct platform_device *pdev, pm_message_t state) |
| { |
| struct mmc_host *mmc = platform_get_drvdata(pdev); |
| if (mmc) { |
| struct msdc_host *host = mmc_priv(mmc); |
| msdc_pm(state, (void *)host); |
| } |
| } |
| |
| static int msdc_drv_suspend(struct platform_device *pdev, pm_message_t state) |
| { |
| if (state.event == PM_EVENT_SUSPEND) |
| msdc_drv_pm(pdev, state); |
| return 0; |
| } |
| |
| static int msdc_drv_resume(struct platform_device *pdev) |
| { |
| struct pm_message state; |
| |
| state.event = PM_EVENT_RESUME; |
| msdc_drv_pm(pdev, state); |
| return 0; |
| } |
| #endif |
| |
| static const struct of_device_id mt7620_sdhci_match[] = { |
| { .compatible = "ralink,mt7620-sdhci" }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, mt7620_sdhci_match); |
| |
| static struct platform_driver mt_msdc_driver = { |
| .probe = msdc_drv_probe, |
| .remove = msdc_drv_remove, |
| #ifdef CONFIG_PM |
| .suspend = msdc_drv_suspend, |
| .resume = msdc_drv_resume, |
| #endif |
| .driver = { |
| .name = DRV_NAME, |
| .of_match_table = mt7620_sdhci_match, |
| }, |
| }; |
| |
| /*--------------------------------------------------------------------------*/ |
| /* module init/exit */ |
| /*--------------------------------------------------------------------------*/ |
| static int __init mt_msdc_init(void) |
| { |
| int ret; |
| u32 reg; |
| |
| // Set the pins for sdxc to sdxc mode |
| //FIXME: this should be done by pinctl and not by the sd driver |
| reg = sdr_read32((void __iomem *)(RALINK_SYSCTL_BASE + 0x60)) & ~(0x3 << 18); |
| sdr_write32((void __iomem *)(RALINK_SYSCTL_BASE + 0x60), reg); |
| |
| ret = platform_driver_register(&mt_msdc_driver); |
| if (ret) { |
| printk(KERN_ERR DRV_NAME ": Can't register driver"); |
| return ret; |
| } |
| |
| #if defined(MT6575_SD_DEBUG) |
| msdc_debug_proc_init(); |
| #endif |
| return 0; |
| } |
| |
| static void __exit mt_msdc_exit(void) |
| { |
| platform_driver_unregister(&mt_msdc_driver); |
| } |
| |
| module_init(mt_msdc_init); |
| module_exit(mt_msdc_exit); |
| MODULE_LICENSE("GPL"); |
| MODULE_DESCRIPTION("MediaTek MT6575 SD/MMC Card Driver"); |
| MODULE_AUTHOR("Infinity Chen <infinity.chen@mediatek.com>"); |