blob: f8151c61488e146b0bd601c5e67b8b7477469757 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2014-2016 Texas Instruments Incorporated - https://www.ti.com/
*/
/dts-v1/;
#include "dra72x.dtsi"
#include "dra7-ipu-dsp-common.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/ti-dra7-atl.h>
/ {
compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
aliases {
display0 = &hdmi0;
};
chosen {
stdout-path = &uart1;
};
evm_12v0: fixedregulator-evm12v0 {
/* main supply */
compatible = "regulator-fixed";
regulator-name = "evm_12v0";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
regulator-always-on;
regulator-boot-on;
};
evm_5v0: fixedregulator-evm5v0 {
/* Output 1 of TPS43351QDAPRQ1 on dra72-evm */
/* Output 1 of LM5140QRWGTQ1 on dra71-evm */
compatible = "regulator-fixed";
regulator-name = "evm_5v0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&evm_12v0>;
regulator-always-on;
regulator-boot-on;
};
evm_3v6: fixedregulator-evm_3v6 {
compatible = "regulator-fixed";
regulator-name = "evm_3v6";
regulator-min-microvolt = <3600000>;
regulator-max-microvolt = <3600000>;
vin-supply = <&evm_5v0>;
regulator-always-on;
regulator-boot-on;
};
vsys_3v3: fixedregulator-vsys3v3 {
/* Output 2 of TPS43351QDAPRQ1 on dra72-evm */
/* Output 2 of LM5140QRWGTQ1 on dra71-evm */
compatible = "regulator-fixed";
regulator-name = "vsys_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&evm_12v0>;
regulator-always-on;
regulator-boot-on;
};
evm_3v3_sw: fixedregulator-evm_3v3 {
/* TPS22965DSG */
compatible = "regulator-fixed";
regulator-name = "evm_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vsys_3v3>;
regulator-always-on;
regulator-boot-on;
};
aic_dvdd: fixedregulator-aic_dvdd {
/* TPS77018DBVT */
compatible = "regulator-fixed";
regulator-name = "aic_dvdd";
vin-supply = <&evm_3v3_sw>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
evm_3v3_sd: fixedregulator-sd {
compatible = "regulator-fixed";
regulator-name = "evm_3v3_sd";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&evm_3v3_sw>;
enable-active-high;
gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
};
extcon_usb1: extcon_usb1 {
compatible = "linux,extcon-usb-gpio";
id-gpios = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
};
extcon_usb2: extcon_usb2 {
compatible = "linux,extcon-usb-gpio";
id-gpios = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
};
hdmi0: connector {
compatible = "hdmi-connector";
label = "hdmi";
type = "a";
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&tpd12s015_out>;
};
};
};
tpd12s015: encoder {
compatible = "ti,tpd12s015";
gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */
<&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */
<&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tpd12s015_in: endpoint {
remote-endpoint = <&hdmi_out>;
};
};
port@1 {
reg = <1>;
tpd12s015_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
};
};
sound0: sound0 {
compatible = "simple-audio-card";
simple-audio-card,name = "DRA7xx-EVM";
simple-audio-card,widgets =
"Headphone", "Headphone Jack",
"Line", "Line Out",
"Microphone", "Mic Jack",
"Line", "Line In";
simple-audio-card,routing =
"Headphone Jack", "HPLOUT",
"Headphone Jack", "HPROUT",
"Line Out", "LLOUT",
"Line Out", "RLOUT",
"MIC3L", "Mic Jack",
"MIC3R", "Mic Jack",
"Mic Jack", "Mic Bias",
"LINE1L", "Line In",
"LINE1R", "Line In";
simple-audio-card,format = "dsp_b";
simple-audio-card,bitclock-master = <&sound0_master>;
simple-audio-card,frame-master = <&sound0_master>;
simple-audio-card,bitclock-inversion;
sound0_master: simple-audio-card,cpu {
sound-dai = <&mcasp3>;
system-clock-frequency = <5644800>;
};
simple-audio-card,codec {
sound-dai = <&tlv320aic3106>;
clocks = <&atl_clkin2_ck>;
};
};
vmmcwl_fixed: fixedregulator-mmcwl {
compatible = "regulator-fixed";
regulator-name = "vmmcwl_fixed";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&gpio5 8 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
clk_ov5640_fixed: clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <24000000>;
};
};
&dra7_pmx_core {
dcan1_pins_default: dcan1-default-pins {
pinctrl-single,pins = <
DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
>;
};
dcan1_pins_sleep: dcan1-sleep-pins {
pinctrl-single,pins = <
DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */
DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */
>;
};
};
&i2c1 {
status = "okay";
clock-frequency = <400000>;
pcf_lcd: gpio@20 {
compatible = "nxp,pcf8575";
reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
pcf_gpio_21: gpio@21 {
compatible = "nxp,pcf8575";
reg = <0x21>;
lines-initial-states = <0x1408>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
tlv320aic3106: tlv320aic3106@19 {
#sound-dai-cells = <0>;
compatible = "ti,tlv320aic3106";
reg = <0x19>;
adc-settle-ms = <40>;
ai3x-micbias-vg = <1>; /* 2.0V */
status = "okay";
/* Regulators */
AVDD-supply = <&evm_3v3_sw>;
IOVDD-supply = <&evm_3v3_sw>;
DRVDD-supply = <&evm_3v3_sw>;
DVDD-supply = <&aic_dvdd>;
};
};
&i2c5 {
status = "okay";
clock-frequency = <400000>;
pcf_hdmi: pcf8575@26 {
compatible = "nxp,pcf8575";
reg = <0x26>;
gpio-controller;
#gpio-cells = <2>;
/*
* initial state is used here to keep the mdio interface
* selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and
* VIN2_S0 driven high otherwise Ethernet stops working
* VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
*/
lines-initial-states = <0x0f2b>;
hdmi-audio-hog {
/* vin6_sel_s0: high: VIN6, low: audio */
gpio-hog;
gpios = <1 GPIO_ACTIVE_HIGH>;
output-low;
line-name = "vin6_sel_s0";
};
};
ov5640@3c {
compatible = "ovti,ov5640";
reg = <0x3c>;
clocks = <&clk_ov5640_fixed>;
clock-names = "xclk";
port {
csi2_cam0: endpoint {
remote-endpoint = <&csi2_phy0>;
clock-lanes = <0>;
data-lanes = <1 2>;
};
};
};
};
&uart1 {
status = "okay";
interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
<&dra7_pmx_core 0x3e0>;
};
&elm {
status = "okay";
};
&gpmc {
/*
* For the existing IOdelay configuration via U-Boot we don't
* support NAND on dra72-evm. Keep it disabled. Enabling it
* requires a different configuration by U-Boot.
*/
status = "disabled";
ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */
nand@0,0 {
/* To use NAND, DIP switch SW5 must be set like so:
* SW5.1 (NAND_SELn) = ON (LOW)
* SW5.9 (GPMC_WPN) = OFF (HIGH)
*/
compatible = "ti,omap2-nand";
reg = <0 0 4>; /* device IO registers */
interrupt-parent = <&gpmc>;
interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
<1 IRQ_TYPE_NONE>; /* termcount */
rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
ti,nand-xfer-type = "prefetch-dma";
ti,nand-ecc-opt = "bch8";
ti,elm-id = <&elm>;
nand-bus-width = <16>;
gpmc,device-width = <2>;
gpmc,sync-clk-ps = <0>;
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <80>;
gpmc,cs-wr-off-ns = <80>;
gpmc,adv-on-ns = <0>;
gpmc,adv-rd-off-ns = <60>;
gpmc,adv-wr-off-ns = <60>;
gpmc,we-on-ns = <10>;
gpmc,we-off-ns = <50>;
gpmc,oe-on-ns = <4>;
gpmc,oe-off-ns = <40>;
gpmc,access-ns = <40>;
gpmc,wr-access-ns = <80>;
gpmc,rd-cycle-ns = <80>;
gpmc,wr-cycle-ns = <80>;
gpmc,bus-turnaround-ns = <0>;
gpmc,cycle2cycle-delay-ns = <0>;
gpmc,clk-activation-ns = <0>;
gpmc,wr-data-mux-bus-ns = <0>;
/* MTD partition table */
/* All SPL-* partitions are sized to minimal length
* which can be independently programmable. For
* NAND flash this is equal to size of erase-block */
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "NAND.SPL";
reg = <0x00000000 0x00020000>;
};
partition@1 {
label = "NAND.SPL.backup1";
reg = <0x00020000 0x00020000>;
};
partition@2 {
label = "NAND.SPL.backup2";
reg = <0x00040000 0x00020000>;
};
partition@3 {
label = "NAND.SPL.backup3";
reg = <0x00060000 0x00020000>;
};
partition@4 {
label = "NAND.u-boot-spl-os";
reg = <0x00080000 0x00040000>;
};
partition@5 {
label = "NAND.u-boot";
reg = <0x000c0000 0x00100000>;
};
partition@6 {
label = "NAND.u-boot-env";
reg = <0x001c0000 0x00020000>;
};
partition@7 {
label = "NAND.u-boot-env.backup1";
reg = <0x001e0000 0x00020000>;
};
partition@8 {
label = "NAND.kernel";
reg = <0x00200000 0x00800000>;
};
partition@9 {
label = "NAND.file-system";
reg = <0x00a00000 0x0f600000>;
};
};
};
&omap_dwc3_1 {
extcon = <&extcon_usb1>;
};
&omap_dwc3_2 {
extcon = <&extcon_usb2>;
};
&usb1 {
dr_mode = "otg";
extcon = <&extcon_usb1>;
};
&usb2 {
dr_mode = "host";
extcon = <&extcon_usb2>;
};
&mmc1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_default>;
vmmc-supply = <&evm_3v3_sd>;
bus-width = <4>;
/*
* SDCD signal is not being used here - using the fact that GPIO mode
* is a viable alternative
*/
cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
max-frequency = <192000000>;
};
&mmc2 {
/* SW5-3 in ON position */
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins_default>;
bus-width = <8>;
non-removable;
max-frequency = <192000000>;
};
&mmc4 {
status = "okay";
vmmc-supply = <&evm_3v6>;
vqmmc-supply = <&vmmcwl_fixed>;
bus-width = <4>;
cap-power-off-card;
keep-power-in-suspend;
non-removable;
pinctrl-names = "default", "hs", "sdr12", "sdr25";
pinctrl-0 = <&mmc4_pins_default>;
pinctrl-1 = <&mmc4_pins_default>;
pinctrl-2 = <&mmc4_pins_default>;
pinctrl-3 = <&mmc4_pins_default>;
#address-cells = <1>;
#size-cells = <0>;
wifi@2 {
compatible = "ti,wl1835";
reg = <2>;
interrupt-parent = <&gpio5>;
interrupts = <7 IRQ_TYPE_EDGE_RISING>;
};
};
&dcan1 {
status = "okay";
pinctrl-names = "default", "sleep", "active";
pinctrl-0 = <&dcan1_pins_sleep>;
pinctrl-1 = <&dcan1_pins_sleep>;
pinctrl-2 = <&dcan1_pins_default>;
};
&qspi {
status = "okay";
spi-max-frequency = <76800000>;
flash@0 {
compatible = "s25fl256s1";
spi-max-frequency = <76800000>;
reg = <0>;
spi-tx-bus-width = <1>;
spi-rx-bus-width = <4>;
#address-cells = <1>;
#size-cells = <1>;
/* MTD partition table.
* The ROM checks the first four physical blocks
* for a valid file to boot and the flash here is
* 64KiB block size.
*/
partition@0 {
label = "QSPI.SPL";
reg = <0x00000000 0x00010000>;
};
partition@1 {
label = "QSPI.SPL.backup1";
reg = <0x00010000 0x00010000>;
};
partition@2 {
label = "QSPI.SPL.backup2";
reg = <0x00020000 0x00010000>;
};
partition@3 {
label = "QSPI.SPL.backup3";
reg = <0x00030000 0x00010000>;
};
partition@4 {
label = "QSPI.u-boot";
reg = <0x00040000 0x00100000>;
};
partition@5 {
label = "QSPI.u-boot-spl-os";
reg = <0x00140000 0x00080000>;
};
partition@6 {
label = "QSPI.u-boot-env";
reg = <0x001c0000 0x00010000>;
};
partition@7 {
label = "QSPI.u-boot-env.backup1";
reg = <0x001d0000 0x0010000>;
};
partition@8 {
label = "QSPI.kernel";
reg = <0x001e0000 0x0800000>;
};
partition@9 {
label = "QSPI.file-system";
reg = <0x009e0000 0x01620000>;
};
};
};
&dss {
status = "okay";
};
&hdmi {
status = "okay";
port {
hdmi_out: endpoint {
remote-endpoint = <&tpd12s015_in>;
};
};
};
&atl {
assigned-clocks = <&abe_dpll_sys_clk_mux>,
<&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>,
<&dpll_abe_ck>,
<&dpll_abe_m2x2_ck>,
<&atl_clkin2_ck>;
assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>;
assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>;
status = "okay";
atl2 {
bws = <DRA7_ATL_WS_MCASP2_FSX>;
aws = <DRA7_ATL_WS_MCASP3_FSX>;
};
};
&mcasp3 {
#sound-dai-cells = <0>;
assigned-clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
assigned-clock-parents = <&atl_clkin2_ck>;
status = "okay";
op-mode = <0>; /* MCASP_IIS_MODE */
tdm-slots = <2>;
/* 4 serializer */
serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
1 2 0 0
>;
tx-num-evt = <32>;
rx-num-evt = <32>;
};
&pcie1_rc {
status = "okay";
};
&csi2_0 {
csi2_phy0: endpoint {
remote-endpoint = <&csi2_cam0>;
clock-lanes = <0>;
data-lanes = <1 2>;
};
};