blob: 0e942513560d619d702efe003e90c1a58a05eea0 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* Common support for CompuLab CM-T3x30 CoMs
*/
#include "omap3-cm-t3x.dtsi"
/ {
cpus {
cpu@0 {
cpu0-supply = <&vcc>;
};
};
sound {
compatible = "ti,omap-twl4030";
ti,model = "cm-t35";
ti,mcbsp = <&mcbsp2>;
};
};
&omap3_pmx_core {
smsc1_pins: smsc1-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */
OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */
>;
};
hsusb0_pins: hsusb0-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */
OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */
OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */
OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */
OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */
OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
>;
};
};
#include "omap-gpmc-smsc911x.dtsi"
&gpmc {
ranges = <5 0 0x2c000000 0x01000000>, /* CM-T3x30 SMSC9x Eth */
<0 0 0x00000000 0x01000000>; /* CM-T3x NAND */
smsc1: ethernet@gpmc {
compatible = "smsc,lan9221", "smsc,lan9115";
pinctrl-names = "default";
pinctrl-0 = <&smsc1_pins>;
interrupt-parent = <&gpio6>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
reg = <5 0 0xff>;
};
};
&i2c1 {
twl: twl@48 {
reg = <0x48>;
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
interrupt-parent = <&intc>;
twl_audio: audio {
compatible = "ti,twl4030-audio";
codec {
};
};
};
};
#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
#include <dt-bindings/input/input.h>
&venc {
vdda-supply = <&vdac>;
};
&mmc1 {
vmmc-supply = <&vmmc1>;
};
&twl_gpio {
ti,use-leds;
/* pullups: BIT(0) */
ti,pullups = <0x000001>;
};
&twl_keypad {
linux,keymap = <
MATRIX_KEY(0x00, 0x01, KEY_A)
MATRIX_KEY(0x00, 0x02, KEY_B)
MATRIX_KEY(0x00, 0x03, KEY_LEFT)
MATRIX_KEY(0x01, 0x01, KEY_UP)
MATRIX_KEY(0x01, 0x02, KEY_ENTER)
MATRIX_KEY(0x01, 0x03, KEY_DOWN)
MATRIX_KEY(0x02, 0x01, KEY_RIGHT)
MATRIX_KEY(0x02, 0x02, KEY_C)
MATRIX_KEY(0x02, 0x03, KEY_D)
>;
};
&hsusb1_phy {
reset-gpios = <&twl_gpio 6 GPIO_ACTIVE_LOW>;
};
&hsusb2_phy {
reset-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>;
};
&usb_otg_hs {
pinctrl-names = "default";
pinctrl-0 = <&hsusb0_pins>;
interface-type = <0>;
usb-phy = <&usb2_phy>;
phys = <&usb2_phy>;
phy-names = "usb2-phy";
mode = <3>;
power = <50>;
};