blob: 559b2bfe4ca7cd0ce74b81e4bd6faf9cca776457 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
*/
#include <dt-bindings/bus/ti-sysc.h>
#include <dt-bindings/clock/omap4.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/omap.h>
#include <dt-bindings/clock/omap4.h>
/ {
compatible = "ti,omap4430", "ti,omap4";
interrupt-parent = <&wakeupgen>;
#address-cells = <1>;
#size-cells = <1>;
chosen { };
aliases {
i2c0 = &i2c1;
i2c1 = &i2c2;
i2c2 = &i2c3;
i2c3 = &i2c4;
mmc0 = &mmc1;
mmc1 = &mmc2;
mmc2 = &mmc3;
mmc3 = &mmc4;
mmc4 = &mmc5;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
serial3 = &uart4;
rproc0 = &dsp;
rproc1 = &ipu;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu@0 {
compatible = "arm,cortex-a9";
device_type = "cpu";
next-level-cache = <&L2>;
reg = <0x0>;
clocks = <&dpll_mpu_ck>;
clock-names = "cpu";
clock-latency = <300000>; /* From omap-cpufreq driver */
};
cpu@1 {
compatible = "arm,cortex-a9";
device_type = "cpu";
next-level-cache = <&L2>;
reg = <0x1>;
};
};
/*
* Needed early by omap4_sram_init() for barrier, do not move to l3
* interconnect as simple-pm-bus probes at module_init() time.
*/
ocmcram: sram@40304000 {
compatible = "mmio-sram";
reg = <0x40304000 0xa000>; /* 40k */
};
gic: interrupt-controller@48241000 {
compatible = "arm,cortex-a9-gic";
interrupt-controller;
#interrupt-cells = <3>;
reg = <0x48241000 0x1000>,
<0x48240100 0x0100>;
interrupt-parent = <&gic>;
};
L2: cache-controller@48242000 {
compatible = "arm,pl310-cache";
reg = <0x48242000 0x1000>;
cache-unified;
cache-level = <2>;
};
local-timer@48240600 {
compatible = "arm,cortex-a9-twd-timer";
clocks = <&mpu_periphclk>;
reg = <0x48240600 0x20>;
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_EDGE_RISING)>;
interrupt-parent = <&gic>;
};
wakeupgen: interrupt-controller@48281000 {
compatible = "ti,omap4-wugen-mpu";
interrupt-controller;
#interrupt-cells = <3>;
reg = <0x48281000 0x1000>;
interrupt-parent = <&gic>;
};
/*
* XXX: Use a flat representation of the OMAP4 interconnect.
* The real OMAP interconnect network is quite complex.
* Since it will not bring real advantage to represent that in DT for
* the moment, just use a fake OCP bus entry to represent the whole bus
* hierarchy.
*/
ocp {
compatible = "simple-pm-bus";
power-domains = <&prm_l4per>;
clocks = <&l3_1_clkctrl OMAP4_L3_MAIN_1_CLKCTRL 0>,
<&l3_2_clkctrl OMAP4_L3_MAIN_2_CLKCTRL 0>,
<&l3_instr_clkctrl OMAP4_L3_MAIN_3_CLKCTRL 0>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
l3-noc@44000000 {
compatible = "ti,omap4-l3-noc";
reg = <0x44000000 0x1000>,
<0x44800000 0x2000>,
<0x45000000 0x1000>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
};
l4_wkup: interconnect@4a300000 {
};
l4_cfg: interconnect@4a000000 {
};
l4_per: interconnect@48000000 {
};
target-module@48210000 {
compatible = "ti,sysc-omap4-simple", "ti,sysc";
power-domains = <&prm_mpu>;
clocks = <&mpuss_clkctrl OMAP4_MPU_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x48210000 0x1f0000>;
mpu {
compatible = "ti,omap4-mpu";
sram = <&ocmcram>;
};
};
l4_abe: interconnect@40100000 {
};
target-module@50000000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x50000000 4>,
<0x50000010 4>,
<0x50000014 4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,syss-mask = <1>;
ti,no-idle-on-init;
clocks = <&l3_2_clkctrl OMAP4_GPMC_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x50000000 0x50000000 0x00001000>, /* regs */
<0x00000000 0x00000000 0x40000000>; /* data */
gpmc: gpmc@50000000 {
compatible = "ti,omap4430-gpmc";
reg = <0x50000000 0x1000>;
#address-cells = <2>;
#size-cells = <1>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&sdma 4>;
dma-names = "rxtx";
gpmc,num-cs = <8>;
gpmc,num-waitpins = <4>;
clocks = <&l3_div_ck>;
clock-names = "fck";
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
};
};
target-module@52000000 {
compatible = "ti,sysc-omap4", "ti,sysc";
reg = <0x52000000 0x4>,
<0x52000010 0x4>;
reg-names = "rev", "sysc";
ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
ti,sysc-midle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>,
<SYSC_IDLE_SMART_WKUP>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>,
<SYSC_IDLE_SMART_WKUP>;
ti,sysc-delay-us = <2>;
power-domains = <&prm_cam>;
clocks = <&iss_clkctrl OMAP4_ISS_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x52000000 0x1000000>;
/* No child device binding, driver in staging */
};
/*
* Note that 4430 needs cross trigger interface (CTI) supported
* before we can configure the interrupts. This means sampling
* events are not supported for pmu. Note that 4460 does not use
* CTI, see also 4460.dtsi.
*/
target-module@54000000 {
compatible = "ti,sysc-omap4-simple", "ti,sysc";
power-domains = <&prm_emu>;
clocks = <&emu_sys_clkctrl OMAP4_DEBUGSS_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x54000000 0x1000000>;
pmu: pmu {
compatible = "arm,cortex-a9-pmu";
};
};
target-module@55082000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x55082000 0x4>,
<0x55082010 0x4>,
<0x55082014 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
clocks = <&ducati_clkctrl OMAP4_IPU_CLKCTRL 0>;
clock-names = "fck";
resets = <&prm_core 2>;
reset-names = "rstctrl";
ranges = <0x0 0x55082000 0x100>;
#size-cells = <1>;
#address-cells = <1>;
mmu_ipu: mmu@0 {
compatible = "ti,omap4-iommu";
reg = <0x0 0x100>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
#iommu-cells = <0>;
ti,iommu-bus-err-back;
};
};
target-module@4012c000 {
compatible = "ti,sysc-omap4", "ti,sysc";
reg = <0x4012c000 0x4>,
<0x4012c010 0x4>;
reg-names = "rev", "sysc";
ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>,
<SYSC_IDLE_SMART_WKUP>;
clocks = <&abe_clkctrl OMAP4_SLIMBUS1_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00000000 0x4012c000 0x1000>, /* MPU */
<0x4902c000 0x4902c000 0x1000>; /* L3 */
/* No child device binding or driver in mainline */
};
target-module@4e000000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x4e000000 0x4>,
<0x4e000010 0x4>;
reg-names = "rev", "sysc";
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ranges = <0x0 0x4e000000 0x2000000>;
#size-cells = <1>;
#address-cells = <1>;
dmm@0 {
compatible = "ti,omap4-dmm";
reg = <0 0x800>;
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
};
};
target-module@4c000000 {
compatible = "ti,sysc-omap4-simple", "ti,sysc";
reg = <0x4c000000 0x4>;
reg-names = "rev";
clocks = <&l3_emif_clkctrl OMAP4_EMIF1_CLKCTRL 0>;
clock-names = "fck";
ti,no-idle;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x4c000000 0x1000000>;
emif1: emif@0 {
compatible = "ti,emif-4d";
reg = <0 0x100>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
phy-type = <1>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
hw-caps-temp-alert;
};
};
target-module@4d000000 {
compatible = "ti,sysc-omap4-simple", "ti,sysc";
reg = <0x4d000000 0x4>;
reg-names = "rev";
clocks = <&l3_emif_clkctrl OMAP4_EMIF2_CLKCTRL 0>;
clock-names = "fck";
ti,no-idle;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x4d000000 0x1000000>;
emif2: emif@0 {
compatible = "ti,emif-4d";
reg = <0 0x100>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
phy-type = <1>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
hw-caps-temp-alert;
};
};
dsp: dsp {
compatible = "ti,omap4-dsp";
ti,bootreg = <&scm_conf 0x304 0>;
iommus = <&mmu_dsp>;
resets = <&prm_tesla 0>;
clocks = <&tesla_clkctrl OMAP4_DSP_CLKCTRL 0>;
firmware-name = "omap4-dsp-fw.xe64T";
mboxes = <&mailbox &mbox_dsp>;
status = "disabled";
};
ipu: ipu@55020000 {
compatible = "ti,omap4-ipu";
reg = <0x55020000 0x10000>;
reg-names = "l2ram";
iommus = <&mmu_ipu>;
resets = <&prm_core 0>, <&prm_core 1>;
clocks = <&ducati_clkctrl OMAP4_IPU_CLKCTRL 0>;
firmware-name = "omap4-ipu-fw.xem3";
mboxes = <&mailbox &mbox_ipu>;
status = "disabled";
};
aes1_target: target-module@4b501000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x4b501080 0x4>,
<0x4b501084 0x4>,
<0x4b501088 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>,
<SYSC_IDLE_SMART_WKUP>;
ti,syss-mask = <1>;
/* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
clocks = <&l4_secure_clkctrl OMAP4_AES1_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x4b501000 0x1000>;
aes1: aes@0 {
compatible = "ti,omap4-aes";
reg = <0 0xa0>;
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&sdma 111>, <&sdma 110>;
dma-names = "tx", "rx";
};
};
aes2_target: target-module@4b701000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x4b701080 0x4>,
<0x4b701084 0x4>,
<0x4b701088 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>,
<SYSC_IDLE_SMART_WKUP>;
ti,syss-mask = <1>;
/* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
clocks = <&l4_secure_clkctrl OMAP4_AES2_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x4b701000 0x1000>;
aes2: aes@0 {
compatible = "ti,omap4-aes";
reg = <0 0xa0>;
interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&sdma 114>, <&sdma 113>;
dma-names = "tx", "rx";
};
};
sham_target: target-module@4b100000 {
compatible = "ti,sysc-omap3-sham", "ti,sysc";
reg = <0x4b100100 0x4>,
<0x4b100110 0x4>,
<0x4b100114 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,syss-mask = <1>;
/* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
clocks = <&l4_secure_clkctrl OMAP4_SHA2MD5_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x4b100000 0x1000>;
sham: sham@0 {
compatible = "ti,omap4-sham";
reg = <0 0x300>;
interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&sdma 119>;
dma-names = "rx";
};
};
abb_mpu: regulator-abb-mpu {
compatible = "ti,abb-v2";
regulator-name = "abb_mpu";
#address-cells = <0>;
#size-cells = <0>;
ti,tranxdone-status-mask = <0x80>;
clocks = <&sys_clkin_ck>;
ti,settling-time = <50>;
ti,clock-cycles = <16>;
status = "disabled";
};
abb_iva: regulator-abb-iva {
compatible = "ti,abb-v2";
regulator-name = "abb_iva";
#address-cells = <0>;
#size-cells = <0>;
ti,tranxdone-status-mask = <0x80000000>;
clocks = <&sys_clkin_ck>;
ti,settling-time = <50>;
ti,clock-cycles = <16>;
status = "disabled";
};
sgx_module: target-module@56000000 {
compatible = "ti,sysc-omap4", "ti,sysc";
reg = <0x5600fe00 0x4>,
<0x5600fe10 0x4>;
reg-names = "rev", "sysc";
ti,sysc-midle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>,
<SYSC_IDLE_SMART_WKUP>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>,
<SYSC_IDLE_SMART_WKUP>;
power-domains = <&prm_gfx>;
clocks = <&l3_gfx_clkctrl OMAP4_GPU_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x56000000 0x2000000>;
gpu@0 {
compatible = "ti,omap4430-gpu", "img,powervr-sgx540";
reg = <0x0 0x2000000>; /* 32MB */
interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
};
};
/*
* DSS is only using l3 mapping without l4 as noted in the TRM
* "10.1.3 DSS Register Manual" for omap4460.
*/
target-module@58000000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x58000000 4>,
<0x58000014 4>;
reg-names = "rev", "syss";
ti,syss-mask = <1>;
power-domains = <&prm_dss>;
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 0>,
<&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>,
<&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>,
<&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>;
clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x58000000 0x1000000>;
dss: dss@0 {
compatible = "ti,omap4-dss";
reg = <0 0x80>;
status = "disabled";
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0x1000000>;
target-module@1000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x1000 0x4>,
<0x1010 0x4>,
<0x1014 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,sysc-midle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
SYSC_OMAP2_ENAWAKEUP |
SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,syss-mask = <1>;
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
<&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
clock-names = "fck", "sys_clk";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x1000 0x1000>;
dispc@0 {
compatible = "ti,omap4-dispc";
reg = <0 0x1000>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
clock-names = "fck";
};
};
target-module@2000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x2000 0x4>,
<0x2010 0x4>,
<0x2014 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,syss-mask = <1>;
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
<&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
clock-names = "fck", "sys_clk";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x2000 0x1000>;
rfbi: encoder@0 {
reg = <0 0x1000>;
status = "disabled";
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, <&l3_div_ck>;
clock-names = "fck", "ick";
};
};
target-module@3000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x3000 0x4>;
reg-names = "rev";
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
clock-names = "sys_clk";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x3000 0x1000>;
venc: encoder@0 {
compatible = "ti,omap4-venc";
reg = <0 0x1000>;
status = "disabled";
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>;
clock-names = "fck";
};
};
target-module@4000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x4000 0x4>,
<0x4010 0x4>,
<0x4014 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
SYSC_OMAP2_ENAWAKEUP |
SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,syss-mask = <1>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x4000 0x1000>;
dsi1: encoder@0 {
compatible = "ti,omap4-dsi";
reg = <0 0x200>,
<0x200 0x40>,
<0x300 0x20>;
reg-names = "proto", "phy", "pll";
interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
<&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
clock-names = "fck", "sys_clk";
#address-cells = <1>;
#size-cells = <0>;
};
};
target-module@5000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x5000 0x4>,
<0x5010 0x4>,
<0x5014 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
SYSC_OMAP2_ENAWAKEUP |
SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,syss-mask = <1>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x5000 0x1000>;
dsi2: encoder@0 {
compatible = "ti,omap4-dsi";
reg = <0 0x200>,
<0x200 0x40>,
<0x300 0x20>;
reg-names = "proto", "phy", "pll";
interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
<&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
clock-names = "fck", "sys_clk";
#address-cells = <1>;
#size-cells = <0>;
};
};
target-module@6000 {
compatible = "ti,sysc-omap4", "ti,sysc";
reg = <0x6000 0x4>,
<0x6010 0x4>;
reg-names = "rev", "sysc";
/*
* Has SYSC_IDLE_SMART and SYSC_IDLE_SMART_WKUP
* but HDMI audio will fail with them.
*/
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>;
ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>;
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>,
<&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
clock-names = "fck", "dss_clk";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x6000 0x2000>;
hdmi: encoder@0 {
compatible = "ti,omap4-hdmi";
reg = <0 0x200>,
<0x200 0x100>,
<0x300 0x100>,
<0x400 0x1000>;
reg-names = "wp", "pll", "phy", "core";
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>,
<&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
clock-names = "fck", "sys_clk";
dmas = <&sdma 76>;
dma-names = "audio_tx";
};
};
};
};
iva_hd_target: target-module@5a000000 {
compatible = "ti,sysc-omap4", "ti,sysc";
reg = <0x5a05a400 0x4>,
<0x5a05a410 0x4>;
reg-names = "rev", "sysc";
ti,sysc-midle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
power-domains = <&prm_ivahd>;
resets = <&prm_ivahd 2>;
reset-names = "rstctrl";
clocks = <&ivahd_clkctrl OMAP4_IVA_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x5a000000 0x5a000000 0x1000000>,
<0x5b000000 0x5b000000 0x1000000>;
iva {
compatible = "ti,ivahd";
};
};
};
};
#include "omap4-l4.dtsi"
#include "omap4-l4-abe.dtsi"
#include "omap44xx-clocks.dtsi"
&prm {
prm_mpu: prm@300 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x300 0x100>;
#power-domain-cells = <0>;
};
prm_tesla: prm@400 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x400 0x100>;
#reset-cells = <1>;
#power-domain-cells = <0>;
};
prm_abe: prm@500 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x500 0x100>;
#power-domain-cells = <0>;
};
prm_always_on_core: prm@600 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x600 0x100>;
#power-domain-cells = <0>;
};
prm_core: prm@700 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x700 0x100>;
#reset-cells = <1>;
#power-domain-cells = <0>;
};
prm_ivahd: prm@f00 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0xf00 0x100>;
#reset-cells = <1>;
#power-domain-cells = <0>;
};
prm_cam: prm@1000 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x1000 0x100>;
#power-domain-cells = <0>;
};
prm_dss: prm@1100 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x1100 0x100>;
#power-domain-cells = <0>;
};
prm_gfx: prm@1200 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x1200 0x100>;
#power-domain-cells = <0>;
};
prm_l3init: prm@1300 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x1300 0x100>;
#power-domain-cells = <0>;
};
prm_l4per: prm@1400 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x1400 0x100>;
#power-domain-cells = <0>;
};
prm_cefuse: prm@1600 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x1600 0x100>;
#power-domain-cells = <0>;
};
prm_wkup: prm@1700 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x1700 0x100>;
#power-domain-cells = <0>;
};
prm_emu: prm@1900 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x1900 0x100>;
#power-domain-cells = <0>;
};
prm_dss: prm@1100 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x1100 0x40>;
#power-domain-cells = <0>;
};
prm_device: prm@1b00 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x1b00 0x40>;
#reset-cells = <1>;
};
};
/* Preferred always-on timer for clockevent */
&timer1_target {
ti,no-reset-on-init;
ti,no-idle;
timer@0 {
assigned-clocks = <&l4_wkup_clkctrl OMAP4_TIMER1_CLKCTRL 24>;
assigned-clock-parents = <&sys_32k_ck>;
};
};