| // SPDX-License-Identifier: GPL-2.0 |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/spmi/spmi.h> |
| |
| &spmi_bus { |
| |
| pm8916_0: pmic@0 { |
| compatible = "qcom,pm8916", "qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pon@800 { |
| compatible = "qcom,pm8916-pon"; |
| reg = <0x800>; |
| mode-bootloader = <0x2>; |
| mode-recovery = <0x1>; |
| |
| pwrkey { |
| compatible = "qcom,pm8941-pwrkey"; |
| interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| linux,code = <KEY_POWER>; |
| }; |
| |
| pm8916_resin: resin { |
| compatible = "qcom,pm8941-resin"; |
| interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| status = "disabled"; |
| }; |
| |
| watchdog { |
| compatible = "qcom,pm8916-wdt"; |
| interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>; |
| timeout-sec = <60>; |
| }; |
| }; |
| |
| pm8916_charger: charger@1000 { |
| compatible = "qcom,pm8916-lbc"; |
| reg = <0x1000>, <0x1200>, <0x1300>, <0x1600>; |
| reg-names = "chgr", "bat_if", "usb", "misc"; |
| |
| interrupts = <0x0 0x10 0 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x10 6 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 0 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 4 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "vbat_det", |
| "fast_chg", |
| "chg_fail", |
| "chg_done", |
| "bat_pres", |
| "temp_ok", |
| "coarse_det", |
| "usb_vbus", |
| "chg_gone", |
| "overtemp"; |
| |
| status = "disabled"; |
| }; |
| |
| pm8916_usbin: usb-detect@1300 { |
| compatible = "qcom,pm8941-misc"; |
| reg = <0x1300>; |
| interrupts = <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "usb_vbus"; |
| status = "disabled"; |
| }; |
| |
| pm8916_temp: temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400>; |
| interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; |
| io-channels = <&pm8916_vadc VADC_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8916_vadc: adc@3100 { |
| compatible = "qcom,spmi-vadc"; |
| reg = <0x3100>; |
| interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| channel@0 { |
| reg = <VADC_USBIN>; |
| qcom,pre-scaling = <1 10>; |
| }; |
| channel@7 { |
| reg = <VADC_VSYS>; |
| qcom,pre-scaling = <1 3>; |
| }; |
| channel@8 { |
| reg = <VADC_DIE_TEMP>; |
| }; |
| channel@9 { |
| reg = <VADC_REF_625MV>; |
| }; |
| channel@a { |
| reg = <VADC_REF_1250MV>; |
| }; |
| channel@e { |
| reg = <VADC_GND_REF>; |
| }; |
| channel@f { |
| reg = <VADC_VDD_VADC>; |
| }; |
| }; |
| |
| pm8916_bms: battery@4000 { |
| compatible = "qcom,pm8916-bms-vm"; |
| reg = <0x4000>; |
| interrupts = <0x0 0x40 0 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x40 1 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x40 2 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x40 3 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x40 4 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x40 5 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "cv_leave", |
| "cv_enter", |
| "ocv_good", |
| "ocv_thr", |
| "fifo", |
| "state_chg"; |
| |
| status = "disabled"; |
| }; |
| |
| rtc@6000 { |
| compatible = "qcom,pm8941-rtc"; |
| reg = <0x6000>, <0x6100>; |
| reg-names = "rtc", "alarm"; |
| interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; |
| }; |
| |
| pm8916_mpps: mpps@a000 { |
| compatible = "qcom,pm8916-mpp", "qcom,spmi-mpp"; |
| reg = <0xa000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&pm8916_mpps 0 0 4>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pm8916_gpios: gpio@c000 { |
| compatible = "qcom,pm8916-gpio", "qcom,spmi-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| gpio-ranges = <&pm8916_gpios 0 0 4>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pm8916_1: pmic@1 { |
| compatible = "qcom,pm8916", "qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8916_pwm: pwm { |
| compatible = "qcom,pm8916-pwm"; |
| |
| #pwm-cells = <2>; |
| |
| status = "disabled"; |
| }; |
| |
| pm8916_vib: vibrator@c000 { |
| compatible = "qcom,pm8916-vib"; |
| reg = <0xc000>; |
| status = "disabled"; |
| }; |
| |
| pm8916_codec: audio-codec@f000 { |
| compatible = "qcom,pm8916-wcd-analog-codec"; |
| reg = <0xf000>; |
| interrupt-parent = <&spmi_bus>; |
| interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x1 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x2 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x3 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x4 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x5 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x6 IRQ_TYPE_NONE>, |
| <0x1 0xf0 0x7 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x0 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x1 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x2 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x3 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x4 IRQ_TYPE_NONE>, |
| <0x1 0xf1 0x5 IRQ_TYPE_NONE>; |
| interrupt-names = "cdc_spk_cnp_int", |
| "cdc_spk_clip_int", |
| "cdc_spk_ocp_int", |
| "mbhc_ins_rem_det1", |
| "mbhc_but_rel_det", |
| "mbhc_but_press_det", |
| "mbhc_ins_rem_det", |
| "mbhc_switch_int", |
| "cdc_ear_ocp_int", |
| "cdc_hphr_ocp_int", |
| "cdc_hphl_ocp_det", |
| "cdc_ear_cnp_int", |
| "cdc_hphr_cnp_int", |
| "cdc_hphl_cnp_int"; |
| #sound-dai-cells = <1>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
