blob: 24cd733c11d10343dbd2ab3d6e78f2757e8b3c72 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/dsa/nxp,sja1105.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: NXP SJA1105 Automotive Ethernet Switch Family Device Tree Bindings
description:
The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944.pdf) of at
least one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum
cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed
depends on the SPI bus master driver.
allOf:
- $ref: "dsa.yaml#"
maintainers:
- Vladimir Oltean <vladimir.oltean@nxp.com>
properties:
compatible:
enum:
- nxp,sja1105e
- nxp,sja1105t
- nxp,sja1105p
- nxp,sja1105q
- nxp,sja1105r
- nxp,sja1105s
- nxp,sja1110a
- nxp,sja1110b
- nxp,sja1110c
- nxp,sja1110d
reg:
maxItems: 1
# Optional container node for the 2 internal MDIO buses of the SJA1110
# (one for the internal 100base-T1 PHYs and the other for the single
# 100base-TX PHY). The "reg" property does not have physical significance.
# The PHY addresses to port correspondence is as follows: for 100base-T1,
# port 5 has PHY 1, port 6 has PHY 2 etc, while for 100base-TX, port 1 has
# PHY 1.
mdios:
type: object
properties:
'#address-cells':
const: 1
'#size-cells':
const: 0
patternProperties:
"^mdio@[0-1]$":
type: object
allOf:
- $ref: "http://devicetree.org/schemas/net/mdio.yaml#"
properties:
compatible:
oneOf:
- enum:
- nxp,sja1110-base-t1-mdio
- nxp,sja1110-base-tx-mdio
reg:
oneOf:
- enum:
- 0
- 1
required:
- compatible
- reg
patternProperties:
"^(ethernet-)?ports$":
patternProperties:
"^(ethernet-)?port@[0-9]+$":
allOf:
- if:
properties:
phy-mode:
contains:
enum:
- rgmii
- rgmii-rxid
- rgmii-txid
- rgmii-id
then:
properties:
rx-internal-delay-ps:
$ref: "#/$defs/internal-delay-ps"
tx-internal-delay-ps:
$ref: "#/$defs/internal-delay-ps"
required:
- compatible
- reg
$defs:
internal-delay-ps:
description:
Disable tunable delay lines using 0 ps, or enable them and select
the phase between 1640 ps (73.8 degree shift at 1Gbps) and 2260 ps
(101.7 degree shift) in increments of 0.9 degrees (20 ps).
enum:
[0, 1640, 1660, 1680, 1700, 1720, 1740, 1760, 1780, 1800, 1820, 1840,
1860, 1880, 1900, 1920, 1940, 1960, 1980, 2000, 2020, 2040, 2060, 2080,
2100, 2120, 2140, 2160, 2180, 2200, 2220, 2240, 2260]
unevaluatedProperties: false
examples:
- |
spi {
#address-cells = <1>;
#size-cells = <0>;
ethernet-switch@1 {
reg = <0x1>;
compatible = "nxp,sja1105t";
ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
phy-handle = <&rgmii_phy6>;
phy-mode = "rgmii-id";
rx-internal-delay-ps = <0>;
tx-internal-delay-ps = <0>;
reg = <0>;
};
port@1 {
phy-handle = <&rgmii_phy3>;
phy-mode = "rgmii-id";
rx-internal-delay-ps = <0>;
tx-internal-delay-ps = <0>;
reg = <1>;
};
port@2 {
phy-handle = <&rgmii_phy4>;
phy-mode = "rgmii-id";
rx-internal-delay-ps = <0>;
tx-internal-delay-ps = <0>;
reg = <2>;
};
port@3 {
phy-handle = <&rgmii_phy4>;
phy-mode = "rgmii-id";
rx-internal-delay-ps = <0>;
tx-internal-delay-ps = <0>;
reg = <3>;
};
port@4 {
ethernet = <&enet2>;
phy-mode = "rgmii";
rx-internal-delay-ps = <0>;
tx-internal-delay-ps = <0>;
reg = <4>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
};