blob: a776cd37c29778afa1c67cf550f8ff2a45f4ce65 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: "http://devicetree.org/schemas/soc/qcom/qcom,geni-se.yaml#"
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
title: GENI Serial Engine QUP Wrapper Controller
maintainers:
- Mukesh Savaliya <msavaliy@codeaurora.org>
- Akash Asthana <akashast@codeaurora.org>
description: |
Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) wrapper
is a programmable module for supporting a wide range of serial interfaces
like UART, SPI, I2C, I3C, etc. A single QUP module can provide upto 8 Serial
Interfaces, using its internal Serial Engines. The GENI Serial Engine QUP
Wrapper controller is modeled as a node with zero or more child nodes each
representing a serial engine.
properties:
compatible:
enum:
- qcom,geni-se-qup
reg:
description: QUP wrapper common register address and length.
maxItems: 1
clock-names:
items:
- const: m-ahb
- const: s-ahb
clocks:
items:
- description: Master AHB Clock
- description: Slave AHB Clock
"#address-cells":
const: 2
"#size-cells":
const: 2
ranges: true
interconnects:
maxItems: 1
interconnect-names:
const: qup-core
iommus:
maxItems: 1
required:
- compatible
- reg
- clock-names
- clocks
- "#address-cells"
- "#size-cells"
- ranges
patternProperties:
"^.*@[0-9a-f]+$":
type: object
description: Common properties for GENI Serial Engine based I2C, SPI and
UART controller.
properties:
reg:
description: GENI Serial Engine register address and length.
maxItems: 1
clock-names:
const: se
clocks:
description: Serial engine core clock needed by the device.
maxItems: 1
interconnects:
minItems: 2
maxItems: 3
interconnect-names:
minItems: 2
items:
- const: qup-core
- const: qup-config
- const: qup-memory
required:
- reg
- clock-names
- clocks
"spi@[0-9a-f]+$":
type: object
description: GENI serial engine based SPI controller. SPI in master mode
supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol
variants.
$ref: /spi/spi-controller.yaml#
properties:
compatible:
enum:
- qcom,geni-spi
interrupts:
maxItems: 1
"#address-cells":
const: 1
"#size-cells":
const: 0
required:
- compatible
- interrupts
- "#address-cells"
- "#size-cells"
"i2c@[0-9a-f]+$":
type: object
description: GENI serial engine based I2C controller.
$ref: /schemas/i2c/i2c-controller.yaml#
properties:
compatible:
enum:
- qcom,geni-i2c
interrupts:
maxItems: 1
"#address-cells":
const: 1
"#size-cells":
const: 0
clock-frequency:
description: Desired I2C bus clock frequency in Hz.
default: 100000
required:
- compatible
- interrupts
- "#address-cells"
- "#size-cells"
"serial@[0-9a-f]+$":
type: object
description: GENI Serial Engine based UART Controller.
$ref: /schemas/serial.yaml#
properties:
compatible:
enum:
- qcom,geni-uart
- qcom,geni-debug-uart
interrupts:
minItems: 1
items:
- description: UART core irq
- description: Wakeup irq (RX GPIO)
required:
- compatible
- interrupts
additionalProperties: false
examples:
- |
#include <dt-bindings/clock/qcom,gcc-sdm845.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
soc {
#address-cells = <2>;
#size-cells = <2>;
geniqup@8c0000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x008c0000 0 0x6000>;
clock-names = "m-ahb", "s-ahb";
clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
<&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
i2c0: i2c@a94000 {
compatible = "qcom,geni-i2c";
reg = <0 0xa94000 0 0x4000>;
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&qup_1_i2c_5_active>;
pinctrl-1 = <&qup_1_i2c_5_sleep>;
#address-cells = <1>;
#size-cells = <0>;
};
uart0: serial@a88000 {
compatible = "qcom,geni-uart";
reg = <0 0xa88000 0 0x7000>;
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&qup_1_uart_3_active>;
pinctrl-1 = <&qup_1_uart_3_sleep>;
};
};
};
...