| /* | 
 |  * This file is part of linux driver the digital TV devices equipped with B2C2 FlexcopII(b)/III | 
 |  * | 
 |  * flexcop-fe-tuner.c - methods for attaching a frontend and controlling DiSEqC. | 
 |  * | 
 |  * see flexcop.c for copyright information. | 
 |  */ | 
 | #include <media/tuner.h> | 
 |  | 
 | #include "flexcop.h" | 
 |  | 
 | #include "stv0299.h" | 
 | #include "mt352.h" | 
 | #include "nxt200x.h" | 
 | #include "bcm3510.h" | 
 | #include "stv0297.h" | 
 | #include "mt312.h" | 
 | #include "lgdt330x.h" | 
 | #include "dvb-pll.h" | 
 | #include "tuner-simple.h" | 
 |  | 
 | #include "s5h1420.h" | 
 | #include "itd1000.h" | 
 |  | 
 | #include "cx24123.h" | 
 | #include "cx24113.h" | 
 |  | 
 | #include "isl6421.h" | 
 |  | 
 | /* lnb control */ | 
 |  | 
 | static int flexcop_set_voltage(struct dvb_frontend *fe, fe_sec_voltage_t voltage) | 
 | { | 
 | 	struct flexcop_device *fc = fe->dvb->priv; | 
 | 	flexcop_ibi_value v; | 
 | 	deb_tuner("polarity/voltage = %u\n", voltage); | 
 |  | 
 | 	v = fc->read_ibi_reg(fc, misc_204); | 
 | 	switch (voltage) { | 
 | 		case SEC_VOLTAGE_OFF: | 
 | 			v.misc_204.ACPI1_sig = 1; | 
 | 			break; | 
 | 		case SEC_VOLTAGE_13: | 
 | 			v.misc_204.ACPI1_sig = 0; | 
 | 			v.misc_204.LNB_L_H_sig = 0; | 
 | 			break; | 
 | 		case SEC_VOLTAGE_18: | 
 | 			v.misc_204.ACPI1_sig = 0; | 
 | 			v.misc_204.LNB_L_H_sig = 1; | 
 | 			break; | 
 | 		default: | 
 | 			err("unknown SEC_VOLTAGE value"); | 
 | 			return -EINVAL; | 
 | 	} | 
 | 	return fc->write_ibi_reg(fc, misc_204, v); | 
 | } | 
 |  | 
 | static int flexcop_sleep(struct dvb_frontend* fe) | 
 | { | 
 | 	struct flexcop_device *fc = fe->dvb->priv; | 
 | /*	flexcop_ibi_value v = fc->read_ibi_reg(fc,misc_204); */ | 
 |  | 
 | 	if (fc->fe_sleep) | 
 | 		return fc->fe_sleep(fe); | 
 |  | 
 | /*	v.misc_204.ACPI3_sig = 1; | 
 | 	fc->write_ibi_reg(fc,misc_204,v);*/ | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int flexcop_set_tone(struct dvb_frontend *fe, fe_sec_tone_mode_t tone) | 
 | { | 
 | 	/* u16 wz_half_period_for_45_mhz[] = { 0x01ff, 0x0154, 0x00ff, 0x00cc }; */ | 
 | 	struct flexcop_device *fc = fe->dvb->priv; | 
 | 	flexcop_ibi_value v; | 
 | 	u16 ax; | 
 | 	v.raw = 0; | 
 |  | 
 | 	deb_tuner("tone = %u\n",tone); | 
 |  | 
 | 	switch (tone) { | 
 | 		case SEC_TONE_ON: | 
 | 			ax = 0x01ff; | 
 | 			break; | 
 | 		case SEC_TONE_OFF: | 
 | 			ax = 0; | 
 | 			break; | 
 | 		default: | 
 | 			err("unknown SEC_TONE value"); | 
 | 			return -EINVAL; | 
 | 	} | 
 |  | 
 | 	v.lnb_switch_freq_200.LNB_CTLPrescaler_sig = 1; /* divide by 2 */ | 
 |  | 
 | 	v.lnb_switch_freq_200.LNB_CTLHighCount_sig = ax; | 
 | 	v.lnb_switch_freq_200.LNB_CTLLowCount_sig  = ax == 0 ? 0x1ff : ax; | 
 |  | 
 | 	return fc->write_ibi_reg(fc,lnb_switch_freq_200,v); | 
 | } | 
 |  | 
 | static void flexcop_diseqc_send_bit(struct dvb_frontend* fe, int data) | 
 | { | 
 | 	flexcop_set_tone(fe, SEC_TONE_ON); | 
 | 	udelay(data ? 500 : 1000); | 
 | 	flexcop_set_tone(fe, SEC_TONE_OFF); | 
 | 	udelay(data ? 1000 : 500); | 
 | } | 
 |  | 
 | static void flexcop_diseqc_send_byte(struct dvb_frontend* fe, int data) | 
 | { | 
 | 	int i, par = 1, d; | 
 |  | 
 | 	for (i = 7; i >= 0; i--) { | 
 | 		d = (data >> i) & 1; | 
 | 		par ^= d; | 
 | 		flexcop_diseqc_send_bit(fe, d); | 
 | 	} | 
 |  | 
 | 	flexcop_diseqc_send_bit(fe, par); | 
 | } | 
 |  | 
 | static int flexcop_send_diseqc_msg(struct dvb_frontend* fe, int len, u8 *msg, unsigned long burst) | 
 | { | 
 | 	int i; | 
 |  | 
 | 	flexcop_set_tone(fe, SEC_TONE_OFF); | 
 | 	mdelay(16); | 
 |  | 
 | 	for (i = 0; i < len; i++) | 
 | 		flexcop_diseqc_send_byte(fe,msg[i]); | 
 |  | 
 | 	mdelay(16); | 
 |  | 
 | 	if (burst != -1) { | 
 | 		if (burst) | 
 | 			flexcop_diseqc_send_byte(fe, 0xff); | 
 | 		else { | 
 | 			flexcop_set_tone(fe, SEC_TONE_ON); | 
 | 			mdelay(12); | 
 | 			udelay(500); | 
 | 			flexcop_set_tone(fe, SEC_TONE_OFF); | 
 | 		} | 
 | 		msleep(20); | 
 | 	} | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int flexcop_diseqc_send_master_cmd(struct dvb_frontend* fe, struct dvb_diseqc_master_cmd* cmd) | 
 | { | 
 | 	return flexcop_send_diseqc_msg(fe, cmd->msg_len, cmd->msg, 0); | 
 | } | 
 |  | 
 | static int flexcop_diseqc_send_burst(struct dvb_frontend* fe, fe_sec_mini_cmd_t minicmd) | 
 | { | 
 | 	return flexcop_send_diseqc_msg(fe, 0, NULL, minicmd); | 
 | } | 
 |  | 
 | /* dvb-s stv0299 */ | 
 | static int samsung_tbmu24112_set_symbol_rate(struct dvb_frontend* fe, u32 srate, u32 ratio) | 
 | { | 
 | 	u8 aclk = 0; | 
 | 	u8 bclk = 0; | 
 |  | 
 | 	if (srate < 1500000) { aclk = 0xb7; bclk = 0x47; } | 
 | 	else if (srate < 3000000) { aclk = 0xb7; bclk = 0x4b; } | 
 | 	else if (srate < 7000000) { aclk = 0xb7; bclk = 0x4f; } | 
 | 	else if (srate < 14000000) { aclk = 0xb7; bclk = 0x53; } | 
 | 	else if (srate < 30000000) { aclk = 0xb6; bclk = 0x53; } | 
 | 	else if (srate < 45000000) { aclk = 0xb4; bclk = 0x51; } | 
 |  | 
 | 	stv0299_writereg (fe, 0x13, aclk); | 
 | 	stv0299_writereg (fe, 0x14, bclk); | 
 | 	stv0299_writereg (fe, 0x1f, (ratio >> 16) & 0xff); | 
 | 	stv0299_writereg (fe, 0x20, (ratio >>  8) & 0xff); | 
 | 	stv0299_writereg (fe, 0x21, (ratio      ) & 0xf0); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int samsung_tbmu24112_tuner_set_params(struct dvb_frontend* fe, struct dvb_frontend_parameters *params) | 
 | { | 
 | 	u8 buf[4]; | 
 | 	u32 div; | 
 | 	struct i2c_msg msg = { .addr = 0x61, .flags = 0, .buf = buf, .len = sizeof(buf) }; | 
 | 	struct flexcop_device *fc = fe->dvb->priv; | 
 |  | 
 | 	div = params->frequency / 125; | 
 |  | 
 | 	buf[0] = (div >> 8) & 0x7f; | 
 | 	buf[1] = div & 0xff; | 
 | 	buf[2] = 0x84;  /* 0xC4 */ | 
 | 	buf[3] = 0x08; | 
 |  | 
 | 	if (params->frequency < 1500000) | 
 | 		buf[3] |= 0x10; | 
 |  | 
 | 	if (fe->ops.i2c_gate_ctrl) | 
 | 		fe->ops.i2c_gate_ctrl(fe, 1); | 
 | 	if (i2c_transfer(&fc->fc_i2c_adap[0].i2c_adap, &msg, 1) != 1) | 
 | 		return -EIO; | 
 | 	return 0; | 
 | } | 
 |  | 
 | static u8 samsung_tbmu24112_inittab[] = { | 
 | 	     0x01, 0x15, | 
 | 	     0x02, 0x30, | 
 | 	     0x03, 0x00, | 
 | 	     0x04, 0x7D, | 
 | 	     0x05, 0x35, | 
 | 	     0x06, 0x02, | 
 | 	     0x07, 0x00, | 
 | 	     0x08, 0xC3, | 
 | 	     0x0C, 0x00, | 
 | 	     0x0D, 0x81, | 
 | 	     0x0E, 0x23, | 
 | 	     0x0F, 0x12, | 
 | 	     0x10, 0x7E, | 
 | 	     0x11, 0x84, | 
 | 	     0x12, 0xB9, | 
 | 	     0x13, 0x88, | 
 | 	     0x14, 0x89, | 
 | 	     0x15, 0xC9, | 
 | 	     0x16, 0x00, | 
 | 	     0x17, 0x5C, | 
 | 	     0x18, 0x00, | 
 | 	     0x19, 0x00, | 
 | 	     0x1A, 0x00, | 
 | 	     0x1C, 0x00, | 
 | 	     0x1D, 0x00, | 
 | 	     0x1E, 0x00, | 
 | 	     0x1F, 0x3A, | 
 | 	     0x20, 0x2E, | 
 | 	     0x21, 0x80, | 
 | 	     0x22, 0xFF, | 
 | 	     0x23, 0xC1, | 
 | 	     0x28, 0x00, | 
 | 	     0x29, 0x1E, | 
 | 	     0x2A, 0x14, | 
 | 	     0x2B, 0x0F, | 
 | 	     0x2C, 0x09, | 
 | 	     0x2D, 0x05, | 
 | 	     0x31, 0x1F, | 
 | 	     0x32, 0x19, | 
 | 	     0x33, 0xFE, | 
 | 	     0x34, 0x93, | 
 | 	     0xff, 0xff, | 
 | }; | 
 |  | 
 | static struct stv0299_config samsung_tbmu24112_config = { | 
 | 	.demod_address = 0x68, | 
 | 	.inittab = samsung_tbmu24112_inittab, | 
 | 	.mclk = 88000000UL, | 
 | 	.invert = 0, | 
 | 	.skip_reinit = 0, | 
 | 	.lock_output = STV0299_LOCKOUTPUT_LK, | 
 | 	.volt13_op0_op1 = STV0299_VOLT13_OP1, | 
 | 	.min_delay_ms = 100, | 
 | 	.set_symbol_rate = samsung_tbmu24112_set_symbol_rate, | 
 | }; | 
 |  | 
 | /* dvb-t mt352 */ | 
 | static int samsung_tdtc9251dh0_demod_init(struct dvb_frontend* fe) | 
 | { | 
 | 	static u8 mt352_clock_config [] = { 0x89, 0x18, 0x2d }; | 
 | 	static u8 mt352_reset [] = { 0x50, 0x80 }; | 
 | 	static u8 mt352_adc_ctl_1_cfg [] = { 0x8E, 0x40 }; | 
 | 	static u8 mt352_agc_cfg [] = { 0x67, 0x28, 0xa1 }; | 
 | 	static u8 mt352_capt_range_cfg[] = { 0x75, 0x32 }; | 
 |  | 
 | 	mt352_write(fe, mt352_clock_config, sizeof(mt352_clock_config)); | 
 | 	udelay(2000); | 
 | 	mt352_write(fe, mt352_reset, sizeof(mt352_reset)); | 
 | 	mt352_write(fe, mt352_adc_ctl_1_cfg, sizeof(mt352_adc_ctl_1_cfg)); | 
 |  | 
 | 	mt352_write(fe, mt352_agc_cfg, sizeof(mt352_agc_cfg)); | 
 | 	mt352_write(fe, mt352_capt_range_cfg, sizeof(mt352_capt_range_cfg)); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int samsung_tdtc9251dh0_calc_regs(struct dvb_frontend* fe, struct dvb_frontend_parameters *params, u8* pllbuf, int buf_len) | 
 | { | 
 | 	u32 div; | 
 | 	unsigned char bs = 0; | 
 |  | 
 | 	if (buf_len < 5) | 
 | 		return -EINVAL; | 
 |  | 
 | 	#define IF_FREQUENCYx6 217    /* 6 * 36.16666666667MHz */ | 
 | 	div = (((params->frequency + 83333) * 3) / 500000) + IF_FREQUENCYx6; | 
 |  | 
 | 	if (params->frequency >= 48000000 && params->frequency <= 154000000) bs = 0x09; | 
 | 	if (params->frequency >= 161000000 && params->frequency <= 439000000) bs = 0x0a; | 
 | 	if (params->frequency >= 447000000 && params->frequency <= 863000000) bs = 0x08; | 
 |  | 
 | 	pllbuf[0] = 0x61; | 
 | 	pllbuf[1] = div >> 8; | 
 | 	pllbuf[2] = div & 0xff; | 
 | 	pllbuf[3] = 0xcc; | 
 | 	pllbuf[4] = bs; | 
 |  | 
 | 	return 5; | 
 | } | 
 |  | 
 | static struct mt352_config samsung_tdtc9251dh0_config = { | 
 | 	.demod_address = 0x0f, | 
 | 	.demod_init    = samsung_tdtc9251dh0_demod_init, | 
 | }; | 
 |  | 
 | static int flexcop_fe_request_firmware(struct dvb_frontend* fe, const struct firmware **fw, char* name) | 
 | { | 
 | 	struct flexcop_device *fc = fe->dvb->priv; | 
 | 	return request_firmware(fw, name, fc->dev); | 
 | } | 
 |  | 
 | static struct lgdt330x_config air2pc_atsc_hd5000_config = { | 
 | 	.demod_address       = 0x59, | 
 | 	.demod_chip          = LGDT3303, | 
 | 	.serial_mpeg         = 0x04, | 
 | 	.clock_polarity_flip = 1, | 
 | }; | 
 |  | 
 | static struct nxt200x_config samsung_tbmv_config = { | 
 | 	.demod_address    = 0x0a, | 
 | }; | 
 |  | 
 | static struct bcm3510_config air2pc_atsc_first_gen_config = { | 
 | 	.demod_address    = 0x0f, | 
 | 	.request_firmware = flexcop_fe_request_firmware, | 
 | }; | 
 |  | 
 | static int skystar23_samsung_tbdu18132_tuner_set_params(struct dvb_frontend* fe, struct dvb_frontend_parameters *params) | 
 | { | 
 | 	u8 buf[4]; | 
 | 	u32 div; | 
 | 	struct i2c_msg msg = { .addr = 0x61, .flags = 0, .buf = buf, .len = sizeof(buf) }; | 
 | 	struct flexcop_device *fc = fe->dvb->priv; | 
 |  | 
 | 	div = (params->frequency + (125/2)) / 125; | 
 |  | 
 | 	buf[0] = (div >> 8) & 0x7f; | 
 | 	buf[1] = (div >> 0) & 0xff; | 
 | 	buf[2] = 0x84 | ((div >> 10) & 0x60); | 
 | 	buf[3] = 0x80; | 
 |  | 
 | 	if (params->frequency < 1550000) | 
 | 		buf[3] |= 0x02; | 
 |  | 
 | 	if (fe->ops.i2c_gate_ctrl) | 
 | 		fe->ops.i2c_gate_ctrl(fe, 1); | 
 | 	if (i2c_transfer(&fc->fc_i2c_adap[0].i2c_adap, &msg, 1) != 1) | 
 | 		return -EIO; | 
 | 	return 0; | 
 | } | 
 |  | 
 | static struct mt312_config skystar23_samsung_tbdu18132_config = { | 
 |  | 
 | 	.demod_address = 0x0e, | 
 | }; | 
 |  | 
 | static int alps_tdee4_stv0297_tuner_set_params(struct dvb_frontend* fe, | 
 | 					       struct dvb_frontend_parameters *fep) | 
 | { | 
 | 	struct flexcop_device *fc = fe->dvb->priv; | 
 | 	u8 buf[4]; | 
 | 	u16 div; | 
 | 	int ret; | 
 |  | 
 | /*  62.5 kHz * 10 */ | 
 | #define REF_FREQ    625 | 
 | #define FREQ_OFFSET 36125 | 
 |  | 
 | 	div = ((fep->frequency/1000 + FREQ_OFFSET ) * 10)  / REF_FREQ; // 4 MHz = 4000 KHz | 
 |  | 
 | 	buf[0] = (u8)( div >> 8) & 0x7f; | 
 | 	buf[1] = (u8)        div & 0xff; | 
 |  | 
 | /* F(osc) = N * Reference Freq. (62.5 kHz) | 
 |  * byte 2 :  0 N14 N13 N12 N11 N10 N9  N8 | 
 |  * byte 3 : N7 N6  N5  N4  N3  N2  N1  N0 | 
 |  * byte 4 : 1  *   *   AGD R3  R2  R1  R0 | 
 |  * byte 5 : C1 *   RE  RTS BS4 BS3 BS2 BS1 | 
 |  * AGD = 1, R3 R2 R1 R0 = 0 1 0 1 => byte 4 = 1**10101 = 0x95 */ | 
 | 	buf[2] = 0x95; | 
 |  | 
 | // Range(MHz)  C1 *  RE RTS BS4 BS3 BS2 BS1  Byte 5 | 
 | //  47 - 153   0  *  0   0   0   0   0   1   0x01 | 
 | // 153 - 430   0  *  0   0   0   0   1   0   0x02 | 
 | // 430 - 822   0  *  0   0   1   0   0   0   0x08 | 
 | // 822 - 862   1  *  0   0   1   0   0   0   0x88 | 
 |  | 
 | 	     if (fep->frequency <= 153000000) buf[3] = 0x01; | 
 | 	else if (fep->frequency <= 430000000) buf[3] = 0x02; | 
 | 	else if (fep->frequency <= 822000000) buf[3] = 0x08; | 
 | 	else buf[3] = 0x88; | 
 |  | 
 | 	if (fe->ops.i2c_gate_ctrl) | 
 | 		fe->ops.i2c_gate_ctrl(fe, 0); | 
 | 	deb_tuner("tuner buffer for %d Hz: %x %x %x %x\n",fep->frequency, buf[0],buf[1],buf[2],buf[3]); | 
 | 	ret = fc->i2c_request(&fc->fc_i2c_adap[2], | 
 | 		FC_WRITE, 0x61, buf[0], &buf[1], 3); | 
 | 	deb_tuner("tuner write returned: %d\n",ret); | 
 |  | 
 | 	return ret; | 
 | } | 
 |  | 
 | static u8 alps_tdee4_stv0297_inittab[] = { | 
 | 	0x80, 0x01, | 
 | 	0x80, 0x00, | 
 | 	0x81, 0x01, | 
 | 	0x81, 0x00, | 
 | 	0x00, 0x48, | 
 | 	0x01, 0x58, | 
 | 	0x03, 0x00, | 
 | 	0x04, 0x00, | 
 | 	0x07, 0x00, | 
 | 	0x08, 0x00, | 
 | 	0x30, 0xff, | 
 | 	0x31, 0x9d, | 
 | 	0x32, 0xff, | 
 | 	0x33, 0x00, | 
 | 	0x34, 0x29, | 
 | 	0x35, 0x55, | 
 | 	0x36, 0x80, | 
 | 	0x37, 0x6e, | 
 | 	0x38, 0x9c, | 
 | 	0x40, 0x1a, | 
 | 	0x41, 0xfe, | 
 | 	0x42, 0x33, | 
 | 	0x43, 0x00, | 
 | 	0x44, 0xff, | 
 | 	0x45, 0x00, | 
 | 	0x46, 0x00, | 
 | 	0x49, 0x04, | 
 | 	0x4a, 0x51, | 
 | 	0x4b, 0xf8, | 
 | 	0x52, 0x30, | 
 | 	0x53, 0x06, | 
 | 	0x59, 0x06, | 
 | 	0x5a, 0x5e, | 
 | 	0x5b, 0x04, | 
 | 	0x61, 0x49, | 
 | 	0x62, 0x0a, | 
 | 	0x70, 0xff, | 
 | 	0x71, 0x04, | 
 | 	0x72, 0x00, | 
 | 	0x73, 0x00, | 
 | 	0x74, 0x0c, | 
 | 	0x80, 0x20, | 
 | 	0x81, 0x00, | 
 | 	0x82, 0x30, | 
 | 	0x83, 0x00, | 
 | 	0x84, 0x04, | 
 | 	0x85, 0x22, | 
 | 	0x86, 0x08, | 
 | 	0x87, 0x1b, | 
 | 	0x88, 0x00, | 
 | 	0x89, 0x00, | 
 | 	0x90, 0x00, | 
 | 	0x91, 0x04, | 
 | 	0xa0, 0x86, | 
 | 	0xa1, 0x00, | 
 | 	0xa2, 0x00, | 
 | 	0xb0, 0x91, | 
 | 	0xb1, 0x0b, | 
 | 	0xc0, 0x5b, | 
 | 	0xc1, 0x10, | 
 | 	0xc2, 0x12, | 
 | 	0xd0, 0x02, | 
 | 	0xd1, 0x00, | 
 | 	0xd2, 0x00, | 
 | 	0xd3, 0x00, | 
 | 	0xd4, 0x02, | 
 | 	0xd5, 0x00, | 
 | 	0xde, 0x00, | 
 | 	0xdf, 0x01, | 
 | 	0xff, 0xff, | 
 | }; | 
 |  | 
 | static struct stv0297_config alps_tdee4_stv0297_config = { | 
 | 	.demod_address = 0x1c, | 
 | 	.inittab = alps_tdee4_stv0297_inittab, | 
 | //	.invert = 1, | 
 | //	.pll_set = alps_tdee4_stv0297_pll_set, | 
 | }; | 
 |  | 
 |  | 
 | /* SkyStar2 rev2.7 (a/u) */ | 
 | static struct s5h1420_config skystar2_rev2_7_s5h1420_config = { | 
 | 	.demod_address = 0x53, | 
 | 	.invert = 1, | 
 | 	.repeated_start_workaround = 1, | 
 | 	.serial_mpeg = 1, | 
 | }; | 
 |  | 
 | static struct itd1000_config skystar2_rev2_7_itd1000_config = { | 
 | 	.i2c_address = 0x61, | 
 | }; | 
 |  | 
 | /* SkyStar2 rev2.8 */ | 
 | static struct cx24123_config skystar2_rev2_8_cx24123_config = { | 
 | 	.demod_address = 0x55, | 
 | 	.dont_use_pll = 1, | 
 | 	.agc_callback = cx24113_agc_callback, | 
 | }; | 
 |  | 
 | static const struct cx24113_config skystar2_rev2_8_cx24113_config = { | 
 | 	.i2c_addr = 0x54, | 
 | 	.xtal_khz = 10111, | 
 | }; | 
 |  | 
 | /* try to figure out the frontend, each card/box can have on of the following list */ | 
 | int flexcop_frontend_init(struct flexcop_device *fc) | 
 | { | 
 | 	struct dvb_frontend_ops *ops; | 
 | 	struct i2c_adapter *i2c = &fc->fc_i2c_adap[0].i2c_adap; | 
 | 	struct i2c_adapter *i2c_tuner; | 
 |  | 
 | 	/* enable no_base_addr - no repeated start when reading */ | 
 | 	fc->fc_i2c_adap[0].no_base_addr = 1; | 
 | 	fc->fe = dvb_attach(s5h1420_attach, &skystar2_rev2_7_s5h1420_config, i2c); | 
 | 	if (fc->fe != NULL) { | 
 | 		flexcop_ibi_value r108; | 
 | 		i2c_tuner = s5h1420_get_tuner_i2c_adapter(fc->fe); | 
 | 		ops = &fc->fe->ops; | 
 |  | 
 | 		fc->fe_sleep = ops->sleep; | 
 | 		ops->sleep   = flexcop_sleep; | 
 |  | 
 | 		fc->dev_type = FC_SKY_REV27; | 
 |  | 
 | 		/* enable no_base_addr - no repeated start when reading */ | 
 | 		fc->fc_i2c_adap[2].no_base_addr = 1; | 
 | 		if (dvb_attach(isl6421_attach, fc->fe, &fc->fc_i2c_adap[2].i2c_adap, 0x08, 1, 1) == NULL) | 
 | 			err("ISL6421 could NOT be attached"); | 
 | 		else | 
 | 			info("ISL6421 successfully attached"); | 
 |  | 
 | 		/* the ITD1000 requires a lower i2c clock - it slows down the stuff for everyone - but is it a problem ? */ | 
 | 		r108.raw = 0x00000506; | 
 | 		fc->write_ibi_reg(fc, tw_sm_c_108, r108); | 
 | 		if (i2c_tuner) { | 
 | 			if (dvb_attach(itd1000_attach, fc->fe, i2c_tuner, &skystar2_rev2_7_itd1000_config) == NULL) | 
 | 				err("ITD1000 could NOT be attached"); | 
 | 			else | 
 | 				info("ITD1000 successfully attached"); | 
 | 		} | 
 | 		goto fe_found; | 
 | 	} | 
 | 	fc->fc_i2c_adap[0].no_base_addr = 0; /* for the next devices we need it again */ | 
 |  | 
 | 	/* try the sky v2.8 (cx24123, isl6421) */ | 
 | 	fc->fe = dvb_attach(cx24123_attach, | 
 | 		&skystar2_rev2_8_cx24123_config, i2c); | 
 | 	if (fc->fe != NULL) { | 
 | 		i2c_tuner = cx24123_get_tuner_i2c_adapter(fc->fe); | 
 | 		if (i2c_tuner != NULL) { | 
 | 			if (dvb_attach(cx24113_attach, fc->fe, | 
 | 					&skystar2_rev2_8_cx24113_config, | 
 | 					i2c_tuner) == NULL) | 
 | 				err("CX24113 could NOT be attached"); | 
 | 			else | 
 | 				info("CX24113 successfully attached"); | 
 | 		} | 
 |  | 
 | 		fc->dev_type = FC_SKY_REV28; | 
 |  | 
 | 		fc->fc_i2c_adap[2].no_base_addr = 1; | 
 | 		if (dvb_attach(isl6421_attach, fc->fe, | 
 | 		       &fc->fc_i2c_adap[2].i2c_adap, 0x08, 0, 0) == NULL) | 
 | 			err("ISL6421 could NOT be attached"); | 
 | 		else | 
 | 			info("ISL6421 successfully attached"); | 
 |  | 
 | 		/* TODO on i2c_adap[1] addr 0x11 (EEPROM) there seems to be an | 
 | 		 * IR-receiver (PIC16F818) - but the card has no input for | 
 | 		 * that ??? */ | 
 |  | 
 | 		goto fe_found; | 
 |     } | 
 |  | 
 | 	/* try the sky v2.6 (stv0299/Samsung tbmu24112(sl1935)) */ | 
 | 	fc->fe = dvb_attach(stv0299_attach, &samsung_tbmu24112_config, i2c); | 
 | 	if (fc->fe != NULL) { | 
 | 		ops = &fc->fe->ops; | 
 |  | 
 | 		ops->tuner_ops.set_params = samsung_tbmu24112_tuner_set_params; | 
 |  | 
 | 		ops->set_voltage = flexcop_set_voltage; | 
 |  | 
 | 		fc->fe_sleep = ops->sleep; | 
 | 		ops->sleep = flexcop_sleep; | 
 |  | 
 | 		fc->dev_type = FC_SKY; | 
 | 		goto fe_found; | 
 | 	} | 
 |  | 
 | 	/* try the air dvb-t (mt352/Samsung tdtc9251dh0(??)) */ | 
 | 	fc->fe = dvb_attach(mt352_attach, &samsung_tdtc9251dh0_config, i2c); | 
 | 	if (fc->fe != NULL) { | 
 | 		fc->dev_type = FC_AIR_DVB; | 
 | 		fc->fe->ops.tuner_ops.calc_regs = samsung_tdtc9251dh0_calc_regs; | 
 | 		goto fe_found; | 
 | 	} | 
 |  | 
 | 	/* try the air atsc 2nd generation (nxt2002) */ | 
 | 	fc->fe = dvb_attach(nxt200x_attach, &samsung_tbmv_config, i2c); | 
 | 	if (fc->fe != NULL) { | 
 | 		fc->dev_type = FC_AIR_ATSC2; | 
 | 		dvb_attach(dvb_pll_attach, fc->fe, 0x61, NULL, DVB_PLL_SAMSUNG_TBMV); | 
 | 		goto fe_found; | 
 | 	} | 
 |  | 
 | 	fc->fe = dvb_attach(lgdt330x_attach, &air2pc_atsc_hd5000_config, i2c); | 
 | 	if (fc->fe != NULL) { | 
 | 		fc->dev_type = FC_AIR_ATSC3; | 
 | 		dvb_attach(simple_tuner_attach, fc->fe, i2c, 0x61, | 
 | 				TUNER_LG_TDVS_H06XF); | 
 | 		goto fe_found; | 
 | 	} | 
 |  | 
 | 	/* try the air atsc 1nd generation (bcm3510)/panasonic ct10s */ | 
 | 	fc->fe = dvb_attach(bcm3510_attach, &air2pc_atsc_first_gen_config, i2c); | 
 | 	if (fc->fe != NULL) { | 
 | 		fc->dev_type = FC_AIR_ATSC1; | 
 | 		goto fe_found; | 
 | 	} | 
 |  | 
 | 	/* try the cable dvb (stv0297) */ | 
 | 	fc->fe = dvb_attach(stv0297_attach, &alps_tdee4_stv0297_config, i2c); | 
 | 	if (fc->fe != NULL) { | 
 | 		fc->dev_type = FC_CABLE; | 
 | 		fc->fe->ops.tuner_ops.set_params = alps_tdee4_stv0297_tuner_set_params; | 
 | 		goto fe_found; | 
 | 	} | 
 |  | 
 | 	/* try the sky v2.3 (vp310/Samsung tbdu18132(tsa5059)) */ | 
 | 	fc->fe = dvb_attach(mt312_attach, | 
 | 		&skystar23_samsung_tbdu18132_config, i2c); | 
 | 	if (fc->fe != NULL) { | 
 | 		ops = &fc->fe->ops; | 
 |  | 
 | 		ops->tuner_ops.set_params = skystar23_samsung_tbdu18132_tuner_set_params; | 
 |  | 
 | 		ops->diseqc_send_master_cmd = flexcop_diseqc_send_master_cmd; | 
 | 		ops->diseqc_send_burst      = flexcop_diseqc_send_burst; | 
 | 		ops->set_tone               = flexcop_set_tone; | 
 | 		ops->set_voltage            = flexcop_set_voltage; | 
 |  | 
 | 		fc->fe_sleep                = ops->sleep; | 
 | 		ops->sleep                  = flexcop_sleep; | 
 |  | 
 | 		fc->dev_type                = FC_SKY_OLD; | 
 | 		goto fe_found; | 
 | 	} | 
 |  | 
 | 	err("no frontend driver found for this B2C2/FlexCop adapter"); | 
 | 	return -ENODEV; | 
 |  | 
 | fe_found: | 
 | 	info("found '%s' .", fc->fe->ops.info.name); | 
 | 	if (dvb_register_frontend(&fc->dvb_adapter, fc->fe)) { | 
 | 		err("frontend registration failed!"); | 
 | 		ops = &fc->fe->ops; | 
 | 		if (ops->release != NULL) | 
 | 			ops->release(fc->fe); | 
 | 		fc->fe = NULL; | 
 | 		return -EINVAL; | 
 | 	} | 
 | 	fc->init_state |= FC_STATE_FE_INIT; | 
 | 	return 0; | 
 | } | 
 |  | 
 | void flexcop_frontend_exit(struct flexcop_device *fc) | 
 | { | 
 | 	if (fc->init_state & FC_STATE_FE_INIT) { | 
 | 		dvb_unregister_frontend(fc->fe); | 
 | 		dvb_frontend_detach(fc->fe); | 
 | 	} | 
 |  | 
 | 	fc->init_state &= ~FC_STATE_FE_INIT; | 
 | } |