| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * LMK04832 Ultra Low-Noise JESD204B Compliant Clock Jitter Cleaner |
| * Pin compatible with the LMK0482x family |
| * |
| * Datasheet: https://www.ti.com/lit/ds/symlink/lmk04832.pdf |
| * |
| * Copyright (c) 2020, Xiphos Systems Corp. |
| * |
| */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/clk.h> |
| #include <linux/clk-provider.h> |
| #include <linux/device.h> |
| #include <linux/gcd.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/module.h> |
| #include <linux/regmap.h> |
| #include <linux/spi/spi.h> |
| |
| /* 0x000 - 0x00d System Functions */ |
| #define LMK04832_REG_RST3W 0x000 |
| #define LMK04832_BIT_RESET BIT(7) |
| #define LMK04832_BIT_SPI_3WIRE_DIS BIT(4) |
| #define LMK04832_REG_POWERDOWN 0x002 |
| #define LMK04832_REG_ID_DEV_TYPE 0x003 |
| #define LMK04832_REG_ID_PROD_MSB 0x004 |
| #define LMK04832_REG_ID_PROD_LSB 0x005 |
| #define LMK04832_REG_ID_MASKREV 0x006 |
| #define LMK04832_REG_ID_VNDR_MSB 0x00c |
| #define LMK04832_REG_ID_VNDR_LSB 0x00d |
| |
| /* 0x100 - 0x137 Device Clock and SYSREF Clock Output Control */ |
| #define LMK04832_REG_CLKOUT_CTRL0(ch) (0x100 + (ch >> 1) * 8) |
| #define LMK04832_BIT_DCLK_DIV_LSB GENMASK(7, 0) |
| #define LMK04832_REG_CLKOUT_CTRL1(ch) (0x101 + (ch >> 1) * 8) |
| #define LMK04832_BIT_DCLKX_Y_DDLY_LSB GENMASK(7, 0) |
| #define LMK04832_REG_CLKOUT_CTRL2(ch) (0x102 + (ch >> 1) * 8) |
| #define LMK04832_BIT_CLKOUTX_Y_PD BIT(7) |
| #define LMK04832_BIT_DCLKX_Y_DDLY_PD BIT(4) |
| #define LMK04832_BIT_DCLKX_Y_DDLY_MSB GENMASK(3, 2) |
| #define LMK04832_BIT_DCLK_DIV_MSB GENMASK(1, 0) |
| #define LMK04832_REG_CLKOUT_SRC_MUX(ch) (0x103 + (ch % 2) + (ch >> 1) * 8) |
| #define LMK04832_BIT_CLKOUT_SRC_MUX BIT(5) |
| #define LMK04832_REG_CLKOUT_CTRL3(ch) (0x103 + (ch >> 1) * 8) |
| #define LMK04832_BIT_DCLKX_Y_PD BIT(4) |
| #define LMK04832_BIT_DCLKX_Y_DCC BIT(2) |
| #define LMK04832_BIT_DCLKX_Y_HS BIT(0) |
| #define LMK04832_REG_CLKOUT_CTRL4(ch) (0x104 + (ch >> 1) * 8) |
| #define LMK04832_BIT_SCLK_PD BIT(4) |
| #define LMK04832_BIT_SCLKX_Y_DIS_MODE GENMASK(3, 2) |
| #define LMK04832_REG_SCLKX_Y_ADLY(ch) (0x105 + (ch >> 1) * 8) |
| #define LMK04832_REG_SCLKX_Y_DDLY(ch) (0x106 + (ch >> 1) * 8) |
| #define LMK04832_BIT_SCLKX_Y_DDLY GENMASK(3, 0) |
| #define LMK04832_REG_CLKOUT_FMT(ch) (0x107 + (ch >> 1) * 8) |
| #define LMK04832_BIT_CLKOUT_FMT(ch) (ch % 2 ? 0xf0 : 0x0f) |
| #define LMK04832_VAL_CLKOUT_FMT_POWERDOWN 0x00 |
| #define LMK04832_VAL_CLKOUT_FMT_LVDS 0x01 |
| #define LMK04832_VAL_CLKOUT_FMT_HSDS6 0x02 |
| #define LMK04832_VAL_CLKOUT_FMT_HSDS8 0x03 |
| #define LMK04832_VAL_CLKOUT_FMT_LVPECL1600 0x04 |
| #define LMK04832_VAL_CLKOUT_FMT_LVPECL2000 0x05 |
| #define LMK04832_VAL_CLKOUT_FMT_LCPECL 0x06 |
| #define LMK04832_VAL_CLKOUT_FMT_CML16 0x07 |
| #define LMK04832_VAL_CLKOUT_FMT_CML24 0x08 |
| #define LMK04832_VAL_CLKOUT_FMT_CML32 0x09 |
| #define LMK04832_VAL_CLKOUT_FMT_CMOS_OFF_INV 0x0a |
| #define LMK04832_VAL_CLKOUT_FMT_CMOS_NOR_OFF 0x0b |
| #define LMK04832_VAL_CLKOUT_FMT_CMOS_INV_INV 0x0c |
| #define LMK04832_VAL_CLKOUT_FMT_CMOS_INV_NOR 0x0d |
| #define LMK04832_VAL_CLKOUT_FMT_CMOS_NOR_INV 0x0e |
| #define LMK04832_VAL_CLKOUT_FMT_CMOS_NOR_NOR 0x0f |
| |
| /* 0x138 - 0x145 SYSREF, SYNC, and Device Config */ |
| #define LMK04832_REG_VCO_OSCOUT 0x138 |
| #define LMK04832_BIT_VCO_MUX GENMASK(6, 5) |
| #define LMK04832_VAL_VCO_MUX_VCO0 0x00 |
| #define LMK04832_VAL_VCO_MUX_VCO1 0x01 |
| #define LMK04832_VAL_VCO_MUX_EXT 0x02 |
| #define LMK04832_REG_SYSREF_OUT 0x139 |
| #define LMK04832_BIT_SYSREF_REQ_EN BIT(6) |
| #define LMK04832_BIT_SYSREF_MUX GENMASK(1, 0) |
| #define LMK04832_VAL_SYSREF_MUX_NORMAL_SYNC 0x00 |
| #define LMK04832_VAL_SYSREF_MUX_RECLK 0x01 |
| #define LMK04832_VAL_SYSREF_MUX_PULSER 0x02 |
| #define LMK04832_VAL_SYSREF_MUX_CONTINUOUS 0x03 |
| #define LMK04832_REG_SYSREF_DIV_MSB 0x13a |
| #define LMK04832_BIT_SYSREF_DIV_MSB GENMASK(4, 0) |
| #define LMK04832_REG_SYSREF_DIV_LSB 0x13b |
| #define LMK04832_REG_SYSREF_DDLY_MSB 0x13c |
| #define LMK04832_BIT_SYSREF_DDLY_MSB GENMASK(4, 0) |
| #define LMK04832_REG_SYSREF_DDLY_LSB 0x13d |
| #define LMK04832_REG_SYSREF_PULSE_CNT 0x13e |
| #define LMK04832_REG_FB_CTRL 0x13f |
| #define LMK04832_BIT_PLL2_RCLK_MUX BIT(7) |
| #define LMK04832_VAL_PLL2_RCLK_MUX_OSCIN 0x00 |
| #define LMK04832_VAL_PLL2_RCLK_MUX_CLKIN 0x01 |
| #define LMK04832_BIT_PLL2_NCLK_MUX BIT(5) |
| #define LMK04832_VAL_PLL2_NCLK_MUX_PLL2_P 0x00 |
| #define LMK04832_VAL_PLL2_NCLK_MUX_FB_MUX 0x01 |
| #define LMK04832_BIT_FB_MUX_EN BIT(0) |
| #define LMK04832_REG_MAIN_PD 0x140 |
| #define LMK04832_BIT_PLL1_PD BIT(7) |
| #define LMK04832_BIT_VCO_LDO_PD BIT(6) |
| #define LMK04832_BIT_VCO_PD BIT(5) |
| #define LMK04832_BIT_OSCIN_PD BIT(4) |
| #define LMK04832_BIT_SYSREF_GBL_PD BIT(3) |
| #define LMK04832_BIT_SYSREF_PD BIT(2) |
| #define LMK04832_BIT_SYSREF_DDLY_PD BIT(1) |
| #define LMK04832_BIT_SYSREF_PLSR_PD BIT(0) |
| #define LMK04832_REG_SYNC 0x143 |
| #define LMK04832_BIT_SYNC_CLR BIT(7) |
| #define LMK04832_BIT_SYNC_1SHOT_EN BIT(6) |
| #define LMK04832_BIT_SYNC_POL BIT(5) |
| #define LMK04832_BIT_SYNC_EN BIT(4) |
| #define LMK04832_BIT_SYNC_MODE GENMASK(1, 0) |
| #define LMK04832_VAL_SYNC_MODE_OFF 0x00 |
| #define LMK04832_VAL_SYNC_MODE_ON 0x01 |
| #define LMK04832_VAL_SYNC_MODE_PULSER_PIN 0x02 |
| #define LMK04832_VAL_SYNC_MODE_PULSER_SPI 0x03 |
| #define LMK04832_REG_SYNC_DIS 0x144 |
| |
| /* 0x146 - 0x14a CLKin Control */ |
| #define LMK04832_REG_CLKIN_SEL0 0x148 |
| #define LMK04832_REG_CLKIN_SEL1 0x149 |
| #define LMK04832_REG_CLKIN_RST 0x14a |
| #define LMK04832_BIT_SDIO_RDBK_TYPE BIT(6) |
| #define LMK04832_BIT_CLKIN_SEL_MUX GENMASK(5, 3) |
| #define LMK04832_VAL_CLKIN_SEL_MUX_SPI_RDBK 0x06 |
| #define LMK04832_BIT_CLKIN_SEL_TYPE GENMASK(2, 0) |
| #define LMK04832_VAL_CLKIN_SEL_TYPE_OUT 0x03 |
| |
| /* 0x14b - 0x152 Holdover */ |
| |
| /* 0x153 - 0x15f PLL1 Configuration */ |
| |
| /* 0x160 - 0x16e PLL2 Configuration */ |
| #define LMK04832_REG_PLL2_R_MSB 0x160 |
| #define LMK04832_BIT_PLL2_R_MSB GENMASK(3, 0) |
| #define LMK04832_REG_PLL2_R_LSB 0x161 |
| #define LMK04832_REG_PLL2_MISC 0x162 |
| #define LMK04832_BIT_PLL2_MISC_P GENMASK(7, 5) |
| #define LMK04832_BIT_PLL2_MISC_REF_2X_EN BIT(0) |
| #define LMK04832_REG_PLL2_N_CAL_0 0x163 |
| #define LMK04832_BIT_PLL2_N_CAL_0 GENMASK(1, 0) |
| #define LMK04832_REG_PLL2_N_CAL_1 0x164 |
| #define LMK04832_REG_PLL2_N_CAL_2 0x165 |
| #define LMK04832_REG_PLL2_N_0 0x166 |
| #define LMK04832_BIT_PLL2_N_0 GENMASK(1, 0) |
| #define LMK04832_REG_PLL2_N_1 0x167 |
| #define LMK04832_REG_PLL2_N_2 0x168 |
| #define LMK04832_REG_PLL2_DLD_CNT_MSB 0x16a |
| #define LMK04832_REG_PLL2_DLD_CNT_LSB 0x16b |
| #define LMK04832_REG_PLL2_LD 0x16e |
| #define LMK04832_BIT_PLL2_LD_MUX GENMASK(7, 3) |
| #define LMK04832_VAL_PLL2_LD_MUX_PLL2_DLD 0x02 |
| #define LMK04832_BIT_PLL2_LD_TYPE GENMASK(2, 0) |
| #define LMK04832_VAL_PLL2_LD_TYPE_OUT_PP 0x03 |
| |
| /* 0x16F - 0x555 Misc Registers */ |
| #define LMK04832_REG_PLL2_PD 0x173 |
| #define LMK04832_BIT_PLL2_PRE_PD BIT(6) |
| #define LMK04832_BIT_PLL2_PD BIT(5) |
| #define LMK04832_REG_PLL1R_RST 0x177 |
| #define LMK04832_REG_CLR_PLL_LOST 0x182 |
| #define LMK04832_REG_RB_PLL_LD 0x183 |
| #define LMK04832_REG_RB_CLK_DAC_VAL_MSB 0x184 |
| #define LMK04832_REG_RB_DAC_VAL_LSB 0x185 |
| #define LMK04832_REG_RB_HOLDOVER 0x188 |
| #define LMK04832_REG_SPI_LOCK 0x555 |
| |
| enum lmk04832_device_types { |
| LMK04832, |
| }; |
| |
| /** |
| * struct lmk04832_device_info - Holds static device information that is |
| * specific to the chip revision |
| * |
| * @pid: Product Identifier |
| * @maskrev: IC version identifier |
| * @num_channels: Number of available output channels (clkout count) |
| * @vco0_range: {min, max} of the VCO0 operating range (in MHz) |
| * @vco1_range: {min, max} of the VCO1 operating range (in MHz) |
| */ |
| struct lmk04832_device_info { |
| u16 pid; |
| u8 maskrev; |
| size_t num_channels; |
| unsigned int vco0_range[2]; |
| unsigned int vco1_range[2]; |
| }; |
| |
| static const struct lmk04832_device_info lmk04832_device_info[] = { |
| [LMK04832] = { |
| .pid = 0x63d1, /* WARNING PROD_ID is inverted in the datasheet */ |
| .maskrev = 0x70, |
| .num_channels = 14, |
| .vco0_range = { 2440, 2580 }, |
| .vco1_range = { 2945, 3255 }, |
| }, |
| }; |
| |
| enum lmk04832_rdbk_type { |
| RDBK_CLKIN_SEL0, |
| RDBK_CLKIN_SEL1, |
| RDBK_RESET, |
| }; |
| |
| struct lmk_dclk { |
| struct lmk04832 *lmk; |
| struct clk_hw hw; |
| u8 id; |
| }; |
| |
| struct lmk_clkout { |
| struct lmk04832 *lmk; |
| struct clk_hw hw; |
| bool sysref; |
| u32 format; |
| u8 id; |
| }; |
| |
| /** |
| * struct lmk04832 - The LMK04832 device structure |
| * |
| * @dev: reference to a struct device, linked to the spi_device |
| * @regmap: struct regmap instance use to access the chip |
| * @sync_mode: operational mode for SYNC signal |
| * @sysref_mux: select SYSREF source |
| * @sysref_pulse_cnt: number of SYSREF pulses generated while not in continuous |
| * mode. |
| * @sysref_ddly: SYSREF digital delay value |
| * @oscin: PLL2 input clock |
| * @vco: reference to the internal VCO clock |
| * @sclk: reference to the internal sysref clock (SCLK) |
| * @vco_rate: user provided VCO rate |
| * @reset_gpio: reference to the reset GPIO |
| * @dclk: list of internal device clock references. |
| * Each pair of clkout clocks share a single device clock (DCLKX_Y) |
| * @clkout: list of output clock references |
| * @clk_data: holds clkout related data like clk_hw* and number of clocks |
| */ |
| struct lmk04832 { |
| struct device *dev; |
| struct regmap *regmap; |
| |
| unsigned int sync_mode; |
| unsigned int sysref_mux; |
| unsigned int sysref_pulse_cnt; |
| unsigned int sysref_ddly; |
| |
| struct clk *oscin; |
| struct clk_hw vco; |
| struct clk_hw sclk; |
| unsigned int vco_rate; |
| |
| struct gpio_desc *reset_gpio; |
| |
| struct lmk_dclk *dclk; |
| struct lmk_clkout *clkout; |
| struct clk_hw_onecell_data *clk_data; |
| }; |
| |
| static bool lmk04832_regmap_rd_regs(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case LMK04832_REG_RST3W ... LMK04832_REG_ID_MASKREV: |
| case LMK04832_REG_ID_VNDR_MSB: |
| case LMK04832_REG_ID_VNDR_LSB: |
| case LMK04832_REG_CLKOUT_CTRL0(0) ... LMK04832_REG_PLL2_DLD_CNT_LSB: |
| case LMK04832_REG_PLL2_LD: |
| case LMK04832_REG_PLL2_PD: |
| case LMK04832_REG_PLL1R_RST: |
| case LMK04832_REG_CLR_PLL_LOST ... LMK04832_REG_RB_DAC_VAL_LSB: |
| case LMK04832_REG_RB_HOLDOVER: |
| case LMK04832_REG_SPI_LOCK: |
| return true; |
| default: |
| return false; |
| }; |
| } |
| |
| static bool lmk04832_regmap_wr_regs(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case LMK04832_REG_RST3W: |
| case LMK04832_REG_POWERDOWN: |
| return true; |
| case LMK04832_REG_ID_DEV_TYPE ... LMK04832_REG_ID_MASKREV: |
| case LMK04832_REG_ID_VNDR_MSB: |
| case LMK04832_REG_ID_VNDR_LSB: |
| return false; |
| case LMK04832_REG_CLKOUT_CTRL0(0) ... LMK04832_REG_PLL2_DLD_CNT_LSB: |
| case LMK04832_REG_PLL2_LD: |
| case LMK04832_REG_PLL2_PD: |
| case LMK04832_REG_PLL1R_RST: |
| case LMK04832_REG_CLR_PLL_LOST ... LMK04832_REG_RB_DAC_VAL_LSB: |
| case LMK04832_REG_RB_HOLDOVER: |
| case LMK04832_REG_SPI_LOCK: |
| return true; |
| default: |
| return false; |
| }; |
| } |
| |
| static const struct regmap_config regmap_config = { |
| .name = "lmk04832", |
| .reg_bits = 16, |
| .val_bits = 8, |
| .use_single_read = 1, |
| .use_single_write = 1, |
| .read_flag_mask = 0x80, |
| .write_flag_mask = 0x00, |
| .readable_reg = lmk04832_regmap_rd_regs, |
| .writeable_reg = lmk04832_regmap_wr_regs, |
| .cache_type = REGCACHE_NONE, |
| .max_register = LMK04832_REG_SPI_LOCK, |
| }; |
| |
| static int lmk04832_vco_is_enabled(struct clk_hw *hw) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, vco); |
| unsigned int tmp; |
| int ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_MAIN_PD, &tmp); |
| if (ret) |
| return ret; |
| |
| return !(FIELD_GET(LMK04832_BIT_OSCIN_PD, tmp) | |
| FIELD_GET(LMK04832_BIT_VCO_PD, tmp) | |
| FIELD_GET(LMK04832_BIT_VCO_LDO_PD, tmp)); |
| } |
| |
| static int lmk04832_vco_prepare(struct clk_hw *hw) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, vco); |
| int ret; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_PLL2_PD, |
| LMK04832_BIT_PLL2_PRE_PD | |
| LMK04832_BIT_PLL2_PD, |
| 0x00); |
| if (ret) |
| return ret; |
| |
| return regmap_update_bits(lmk->regmap, LMK04832_REG_MAIN_PD, |
| LMK04832_BIT_VCO_LDO_PD | |
| LMK04832_BIT_VCO_PD | |
| LMK04832_BIT_OSCIN_PD, 0x00); |
| } |
| |
| static void lmk04832_vco_unprepare(struct clk_hw *hw) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, vco); |
| |
| regmap_update_bits(lmk->regmap, LMK04832_REG_PLL2_PD, |
| LMK04832_BIT_PLL2_PRE_PD | LMK04832_BIT_PLL2_PD, |
| 0xff); |
| |
| /* Don't set LMK04832_BIT_OSCIN_PD since other clocks depend on it */ |
| regmap_update_bits(lmk->regmap, LMK04832_REG_MAIN_PD, |
| LMK04832_BIT_VCO_LDO_PD | LMK04832_BIT_VCO_PD, 0xff); |
| } |
| |
| static unsigned long lmk04832_vco_recalc_rate(struct clk_hw *hw, |
| unsigned long prate) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, vco); |
| const unsigned int pll2_p[] = {8, 2, 2, 3, 4, 5, 6, 7}; |
| unsigned int pll2_n, p, pll2_r; |
| unsigned int pll2_misc; |
| unsigned long vco_rate; |
| u8 tmp[3]; |
| int ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_PLL2_MISC, &pll2_misc); |
| if (ret) |
| return ret; |
| |
| p = FIELD_GET(LMK04832_BIT_PLL2_MISC_P, pll2_misc); |
| |
| ret = regmap_bulk_read(lmk->regmap, LMK04832_REG_PLL2_N_0, &tmp, 3); |
| if (ret) |
| return ret; |
| |
| pll2_n = FIELD_PREP(0x030000, tmp[0]) | |
| FIELD_PREP(0x00ff00, tmp[1]) | |
| FIELD_PREP(0x0000ff, tmp[2]); |
| |
| ret = regmap_bulk_read(lmk->regmap, LMK04832_REG_PLL2_R_MSB, &tmp, 2); |
| if (ret) |
| return ret; |
| |
| pll2_r = FIELD_PREP(0x0f00, tmp[0]) | |
| FIELD_PREP(0x00ff, tmp[1]); |
| |
| vco_rate = (prate << FIELD_GET(LMK04832_BIT_PLL2_MISC_REF_2X_EN, |
| pll2_misc)) * pll2_n * pll2_p[p] / pll2_r; |
| |
| return vco_rate; |
| } |
| |
| /** |
| * lmk04832_check_vco_ranges - Check requested VCO frequency against VCO ranges |
| * |
| * @lmk: Reference to the lmk device |
| * @rate: Desired output rate for the VCO |
| * |
| * The LMK04832 has 2 internal VCO, each with independent operating ranges. |
| * Use the device_info structure to determine which VCO to use based on rate. |
| * |
| * Returns: VCO_MUX value or negative errno. |
| */ |
| static int lmk04832_check_vco_ranges(struct lmk04832 *lmk, unsigned long rate) |
| { |
| struct spi_device *spi = to_spi_device(lmk->dev); |
| const struct lmk04832_device_info *info; |
| unsigned long mhz = rate / 1000000; |
| |
| info = &lmk04832_device_info[spi_get_device_id(spi)->driver_data]; |
| |
| if (mhz >= info->vco0_range[0] && mhz <= info->vco0_range[1]) |
| return LMK04832_VAL_VCO_MUX_VCO0; |
| |
| if (mhz >= info->vco1_range[0] && mhz <= info->vco1_range[1]) |
| return LMK04832_VAL_VCO_MUX_VCO1; |
| |
| dev_err(lmk->dev, "%lu Hz is out of VCO ranges\n", rate); |
| return -ERANGE; |
| } |
| |
| /** |
| * lmk04832_calc_pll2_params - Get PLL2 parameters used to set the VCO frequency |
| * |
| * @prate: parent rate to the PLL2, usually OSCin |
| * @rate: Desired output rate for the VCO |
| * @n: reference to PLL2_N |
| * @p: reference to PLL2_P |
| * @r: reference to PLL2_R |
| * |
| * This functions assumes LMK04832_BIT_PLL2_MISC_REF_2X_EN is set since it is |
| * recommended in the datasheet because a higher phase detector frequencies |
| * makes the design of wider loop bandwidth filters possible. |
| * |
| * the VCO rate can be calculated using the following expression: |
| * |
| * VCO = OSCin * 2 * PLL2_N * PLL2_P / PLL2_R |
| * |
| * Returns: vco rate or negative errno. |
| */ |
| static long lmk04832_calc_pll2_params(unsigned long prate, unsigned long rate, |
| unsigned int *n, unsigned int *p, |
| unsigned int *r) |
| { |
| unsigned int pll2_n, pll2_p, pll2_r; |
| unsigned long num, div; |
| |
| /* Set PLL2_P to a fixed value to simplify optimizations */ |
| pll2_p = 2; |
| |
| div = gcd(rate, prate); |
| |
| num = DIV_ROUND_CLOSEST(rate, div); |
| pll2_r = DIV_ROUND_CLOSEST(prate, div); |
| |
| if (num > 4) { |
| pll2_n = num >> 2; |
| } else { |
| pll2_r = pll2_r << 2; |
| pll2_n = num; |
| } |
| |
| if (pll2_n < 1 || pll2_n > 0x03ffff) |
| return -EINVAL; |
| if (pll2_r < 1 || pll2_r > 0xfff) |
| return -EINVAL; |
| |
| *n = pll2_n; |
| *p = pll2_p; |
| *r = pll2_r; |
| |
| return DIV_ROUND_CLOSEST(prate * 2 * pll2_p * pll2_n, pll2_r); |
| } |
| |
| static long lmk04832_vco_round_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long *prate) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, vco); |
| unsigned int n, p, r; |
| long vco_rate; |
| int ret; |
| |
| ret = lmk04832_check_vco_ranges(lmk, rate); |
| if (ret < 0) |
| return ret; |
| |
| vco_rate = lmk04832_calc_pll2_params(*prate, rate, &n, &p, &r); |
| if (vco_rate < 0) { |
| dev_err(lmk->dev, "PLL2 parameters out of range\n"); |
| return vco_rate; |
| } |
| |
| if (rate != vco_rate) |
| return -EINVAL; |
| |
| return vco_rate; |
| } |
| |
| static int lmk04832_vco_set_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long prate) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, vco); |
| unsigned int n, p, r; |
| long vco_rate; |
| int vco_mux; |
| int ret; |
| |
| vco_mux = lmk04832_check_vco_ranges(lmk, rate); |
| if (vco_mux < 0) |
| return vco_mux; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_VCO_OSCOUT, |
| LMK04832_BIT_VCO_MUX, |
| FIELD_PREP(LMK04832_BIT_VCO_MUX, vco_mux)); |
| if (ret) |
| return ret; |
| |
| vco_rate = lmk04832_calc_pll2_params(prate, rate, &n, &p, &r); |
| if (vco_rate < 0) { |
| dev_err(lmk->dev, "failed to determine PLL2 parameters\n"); |
| return vco_rate; |
| } |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_PLL2_R_MSB, |
| LMK04832_BIT_PLL2_R_MSB, |
| FIELD_GET(0x000700, r)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_PLL2_R_LSB, |
| FIELD_GET(0x0000ff, r)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_PLL2_MISC, |
| LMK04832_BIT_PLL2_MISC_P, |
| FIELD_PREP(LMK04832_BIT_PLL2_MISC_P, p)); |
| if (ret) |
| return ret; |
| |
| /* |
| * PLL2_N registers must be programmed after other PLL2 dividers are |
| * programmed to ensure proper VCO frequency calibration |
| */ |
| ret = regmap_write(lmk->regmap, LMK04832_REG_PLL2_N_0, |
| FIELD_GET(0x030000, n)); |
| if (ret) |
| return ret; |
| ret = regmap_write(lmk->regmap, LMK04832_REG_PLL2_N_1, |
| FIELD_GET(0x00ff00, n)); |
| if (ret) |
| return ret; |
| |
| return regmap_write(lmk->regmap, LMK04832_REG_PLL2_N_2, |
| FIELD_GET(0x0000ff, n)); |
| } |
| |
| static const struct clk_ops lmk04832_vco_ops = { |
| .is_enabled = lmk04832_vco_is_enabled, |
| .prepare = lmk04832_vco_prepare, |
| .unprepare = lmk04832_vco_unprepare, |
| .recalc_rate = lmk04832_vco_recalc_rate, |
| .round_rate = lmk04832_vco_round_rate, |
| .set_rate = lmk04832_vco_set_rate, |
| }; |
| |
| /* |
| * lmk04832_register_vco - Initialize the internal VCO and clock distribution |
| * path in PLL2 single loop mode. |
| */ |
| static int lmk04832_register_vco(struct lmk04832 *lmk) |
| { |
| const char *parent_names[1]; |
| struct clk_init_data init; |
| int ret; |
| |
| init.name = "lmk-vco"; |
| parent_names[0] = __clk_get_name(lmk->oscin); |
| init.parent_names = parent_names; |
| |
| init.ops = &lmk04832_vco_ops; |
| init.num_parents = 1; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_VCO_OSCOUT, |
| LMK04832_BIT_VCO_MUX, |
| FIELD_PREP(LMK04832_BIT_VCO_MUX, |
| LMK04832_VAL_VCO_MUX_VCO1)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_FB_CTRL, |
| LMK04832_BIT_PLL2_RCLK_MUX | |
| LMK04832_BIT_PLL2_NCLK_MUX, |
| FIELD_PREP(LMK04832_BIT_PLL2_RCLK_MUX, |
| LMK04832_VAL_PLL2_RCLK_MUX_OSCIN)| |
| FIELD_PREP(LMK04832_BIT_PLL2_NCLK_MUX, |
| LMK04832_VAL_PLL2_NCLK_MUX_PLL2_P)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_PLL2_MISC, |
| LMK04832_BIT_PLL2_MISC_REF_2X_EN, |
| LMK04832_BIT_PLL2_MISC_REF_2X_EN); |
| if (ret) |
| return ret; |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_PLL2_LD, |
| FIELD_PREP(LMK04832_BIT_PLL2_LD_MUX, |
| LMK04832_VAL_PLL2_LD_MUX_PLL2_DLD) | |
| FIELD_PREP(LMK04832_BIT_PLL2_LD_TYPE, |
| LMK04832_VAL_PLL2_LD_TYPE_OUT_PP)); |
| if (ret) |
| return ret; |
| |
| lmk->vco.init = &init; |
| return devm_clk_hw_register(lmk->dev, &lmk->vco); |
| } |
| |
| static int lmk04832_clkout_set_ddly(struct lmk04832 *lmk, int id) |
| { |
| const int dclk_div_adj[] = {0, 0, -2, -2, 0, 3, -1, 0}; |
| unsigned int sclkx_y_ddly = 10; |
| unsigned int dclkx_y_ddly; |
| unsigned int dclkx_y_div; |
| unsigned int sysref_ddly; |
| unsigned int dclkx_y_hs; |
| unsigned int lsb, msb; |
| int ret; |
| |
| ret = regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_CTRL2(id), |
| LMK04832_BIT_DCLKX_Y_DDLY_PD, |
| FIELD_PREP(LMK04832_BIT_DCLKX_Y_DDLY_PD, 0)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_SYSREF_DDLY_LSB, &lsb); |
| if (ret) |
| return ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_SYSREF_DDLY_MSB, &msb); |
| if (ret) |
| return ret; |
| |
| sysref_ddly = FIELD_GET(LMK04832_BIT_SYSREF_DDLY_MSB, msb) << 8 | lsb; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_CTRL0(id), &lsb); |
| if (ret) |
| return ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_CTRL2(id), &msb); |
| if (ret) |
| return ret; |
| |
| dclkx_y_div = FIELD_GET(LMK04832_BIT_DCLK_DIV_MSB, msb) << 8 | lsb; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_CTRL3(id), &lsb); |
| if (ret) |
| return ret; |
| |
| dclkx_y_hs = FIELD_GET(LMK04832_BIT_DCLKX_Y_HS, lsb); |
| |
| dclkx_y_ddly = sysref_ddly + 1 - |
| dclk_div_adj[dclkx_y_div < 6 ? dclkx_y_div : 7] - |
| dclkx_y_hs + sclkx_y_ddly; |
| |
| if (dclkx_y_ddly < 7 || dclkx_y_ddly > 0x3fff) { |
| dev_err(lmk->dev, "DCLKX_Y_DDLY out of range (%d)\n", |
| dclkx_y_ddly); |
| return -EINVAL; |
| } |
| |
| ret = regmap_write(lmk->regmap, |
| LMK04832_REG_SCLKX_Y_DDLY(id), |
| FIELD_GET(LMK04832_BIT_SCLKX_Y_DDLY, sclkx_y_ddly)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_CLKOUT_CTRL1(id), |
| FIELD_GET(0x00ff, dclkx_y_ddly)); |
| if (ret) |
| return ret; |
| |
| dev_dbg(lmk->dev, "clkout%02u: sysref_ddly=%u, dclkx_y_ddly=%u, " |
| "dclk_div_adj=%+d, dclkx_y_hs=%u, sclkx_y_ddly=%u\n", |
| id, sysref_ddly, dclkx_y_ddly, |
| dclk_div_adj[dclkx_y_div < 6 ? dclkx_y_div : 7], |
| dclkx_y_hs, sclkx_y_ddly); |
| |
| return regmap_update_bits(lmk->regmap, LMK04832_REG_CLKOUT_CTRL2(id), |
| LMK04832_BIT_DCLKX_Y_DDLY_MSB, |
| FIELD_GET(0x0300, dclkx_y_ddly)); |
| } |
| |
| /** lmk04832_sclk_sync - Establish deterministic phase relationship between sclk |
| * and dclk |
| * |
| * @lmk: Reference to the lmk device |
| * |
| * The synchronization sequence: |
| * - in the datasheet https://www.ti.com/lit/ds/symlink/lmk04832.pdf, p.31 |
| * (8.3.3.1 How to enable SYSREF) |
| * - Ti forum: https://e2e.ti.com/support/clock-and-timing/f/48/t/970972 |
| * |
| * Returns 0 or negative errno. |
| */ |
| static int lmk04832_sclk_sync_sequence(struct lmk04832 *lmk) |
| { |
| int ret; |
| int i; |
| |
| /* 1. (optional) mute all sysref_outputs during synchronization */ |
| /* 2. Enable and write device clock digital delay to applicable clocks */ |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_MAIN_PD, |
| LMK04832_BIT_SYSREF_DDLY_PD, |
| FIELD_PREP(LMK04832_BIT_SYSREF_DDLY_PD, 0)); |
| if (ret) |
| return ret; |
| |
| for (i = 0; i < lmk->clk_data->num; i += 2) { |
| ret = lmk04832_clkout_set_ddly(lmk, i); |
| if (ret) |
| return ret; |
| } |
| |
| /* |
| * 3. Configure SYNC_MODE to SYNC_PIN and SYSREF_MUX to Normal SYNC, |
| * and clear SYSREF_REQ_EN (see 6.) |
| */ |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYSREF_OUT, |
| LMK04832_BIT_SYSREF_REQ_EN | |
| LMK04832_BIT_SYSREF_MUX, |
| FIELD_PREP(LMK04832_BIT_SYSREF_REQ_EN, 0) | |
| FIELD_PREP(LMK04832_BIT_SYSREF_MUX, |
| LMK04832_VAL_SYSREF_MUX_NORMAL_SYNC)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC, |
| LMK04832_BIT_SYNC_MODE, |
| FIELD_PREP(LMK04832_BIT_SYNC_MODE, |
| LMK04832_VAL_SYNC_MODE_ON)); |
| if (ret) |
| return ret; |
| |
| /* 4. Clear SYNXC_DISx or applicable clocks and clear SYNC_DISSYSREF */ |
| ret = regmap_write(lmk->regmap, LMK04832_REG_SYNC_DIS, 0x00); |
| if (ret) |
| return ret; |
| |
| /* |
| * 5. If SCLKX_Y_DDLY != 0, Set SYSREF_CLR=1 for at least 15 clock |
| * distribution path cycles (VCO cycles), then back to 0. In |
| * PLL2-only use case, this will be complete in less than one SPI |
| * transaction. If SYSREF local digital delay is not used, this step |
| * can be skipped. |
| */ |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC, |
| LMK04832_BIT_SYNC_CLR, |
| FIELD_PREP(LMK04832_BIT_SYNC_CLR, 0x01)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC, |
| LMK04832_BIT_SYNC_CLR, |
| FIELD_PREP(LMK04832_BIT_SYNC_CLR, 0x00)); |
| if (ret) |
| return ret; |
| |
| /* |
| * 6. Toggle SYNC_POL state between inverted and not inverted. |
| * If you use an external signal on the SYNC pin instead of toggling |
| * SYNC_POL, make sure that SYSREF_REQ_EN=0 so that the SYSREF_MUX |
| * does not shift into continuous SYSREF mode. |
| */ |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC, |
| LMK04832_BIT_SYNC_POL, |
| FIELD_PREP(LMK04832_BIT_SYNC_POL, 0x01)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC, |
| LMK04832_BIT_SYNC_POL, |
| FIELD_PREP(LMK04832_BIT_SYNC_POL, 0x00)); |
| if (ret) |
| return ret; |
| |
| /* 7. Set all SYNC_DISx=1, including SYNC_DISSYSREF */ |
| ret = regmap_write(lmk->regmap, LMK04832_REG_SYNC_DIS, 0xff); |
| if (ret) |
| return ret; |
| |
| /* 8. Restore state of SYNC_MODE and SYSREF_MUX to desired values */ |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYSREF_OUT, |
| LMK04832_BIT_SYSREF_MUX, |
| FIELD_PREP(LMK04832_BIT_SYSREF_MUX, |
| lmk->sysref_mux)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC, |
| LMK04832_BIT_SYNC_MODE, |
| FIELD_PREP(LMK04832_BIT_SYNC_MODE, |
| lmk->sync_mode)); |
| if (ret) |
| return ret; |
| |
| /* |
| * 9. (optional) if SCLKx_y_DIS_MODE was used to mute SYSREF outputs |
| * during the SYNC event, restore SCLKx_y_DIS_MODE=0 for active state, |
| * or set SYSREF_GBL_PD=0 if SCLKx_y_DIS_MODE is set to a conditional |
| * option. |
| */ |
| |
| /* |
| * 10. (optional) To reduce power consumption, after the synchronization |
| * event is complete, DCLKx_y_DDLY_PD=1 and SYSREF_DDLY_PD=1 disable the |
| * digital delay counters (which are only used immediately after the |
| * SYNC pulse to delay the output by some number of VCO counts). |
| */ |
| |
| return ret; |
| } |
| |
| static int lmk04832_sclk_is_enabled(struct clk_hw *hw) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, sclk); |
| unsigned int tmp; |
| int ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_MAIN_PD, &tmp); |
| if (ret) |
| return ret; |
| |
| return FIELD_GET(LMK04832_BIT_SYSREF_PD, tmp); |
| } |
| |
| static int lmk04832_sclk_prepare(struct clk_hw *hw) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, sclk); |
| |
| return regmap_update_bits(lmk->regmap, LMK04832_REG_MAIN_PD, |
| LMK04832_BIT_SYSREF_PD, 0x00); |
| } |
| |
| static void lmk04832_sclk_unprepare(struct clk_hw *hw) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, sclk); |
| |
| regmap_update_bits(lmk->regmap, LMK04832_REG_MAIN_PD, |
| LMK04832_BIT_SYSREF_PD, LMK04832_BIT_SYSREF_PD); |
| } |
| |
| static unsigned long lmk04832_sclk_recalc_rate(struct clk_hw *hw, |
| unsigned long prate) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, sclk); |
| unsigned int sysref_div; |
| u8 tmp[2]; |
| int ret; |
| |
| ret = regmap_bulk_read(lmk->regmap, LMK04832_REG_SYSREF_DIV_MSB, &tmp, 2); |
| if (ret) |
| return ret; |
| |
| sysref_div = FIELD_GET(LMK04832_BIT_SYSREF_DIV_MSB, tmp[0]) << 8 | |
| tmp[1]; |
| |
| return DIV_ROUND_CLOSEST(prate, sysref_div); |
| } |
| |
| static long lmk04832_sclk_round_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long *prate) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, sclk); |
| unsigned long sclk_rate; |
| unsigned int sysref_div; |
| |
| sysref_div = DIV_ROUND_CLOSEST(*prate, rate); |
| sclk_rate = DIV_ROUND_CLOSEST(*prate, sysref_div); |
| |
| if (sysref_div < 0x07 || sysref_div > 0x1fff) { |
| dev_err(lmk->dev, "SYSREF divider out of range\n"); |
| return -EINVAL; |
| } |
| |
| if (rate != sclk_rate) |
| return -EINVAL; |
| |
| return sclk_rate; |
| } |
| |
| static int lmk04832_sclk_set_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long prate) |
| { |
| struct lmk04832 *lmk = container_of(hw, struct lmk04832, sclk); |
| unsigned int sysref_div; |
| int ret; |
| |
| sysref_div = DIV_ROUND_CLOSEST(prate, rate); |
| |
| if (sysref_div < 0x07 || sysref_div > 0x1fff) { |
| dev_err(lmk->dev, "SYSREF divider out of range\n"); |
| return -EINVAL; |
| } |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_SYSREF_DIV_MSB, |
| FIELD_GET(0x1f00, sysref_div)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_SYSREF_DIV_LSB, |
| FIELD_GET(0x00ff, sysref_div)); |
| if (ret) |
| return ret; |
| |
| ret = lmk04832_sclk_sync_sequence(lmk); |
| if (ret) |
| dev_err(lmk->dev, "SYNC sequence failed\n"); |
| |
| return ret; |
| } |
| |
| static const struct clk_ops lmk04832_sclk_ops = { |
| .is_enabled = lmk04832_sclk_is_enabled, |
| .prepare = lmk04832_sclk_prepare, |
| .unprepare = lmk04832_sclk_unprepare, |
| .recalc_rate = lmk04832_sclk_recalc_rate, |
| .round_rate = lmk04832_sclk_round_rate, |
| .set_rate = lmk04832_sclk_set_rate, |
| }; |
| |
| static int lmk04832_register_sclk(struct lmk04832 *lmk) |
| { |
| const char *parent_names[1]; |
| struct clk_init_data init; |
| int ret; |
| |
| init.name = "lmk-sclk"; |
| parent_names[0] = clk_hw_get_name(&lmk->vco); |
| init.parent_names = parent_names; |
| |
| init.ops = &lmk04832_sclk_ops; |
| init.flags = CLK_SET_RATE_PARENT; |
| init.num_parents = 1; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYSREF_OUT, |
| LMK04832_BIT_SYSREF_MUX, |
| FIELD_PREP(LMK04832_BIT_SYSREF_MUX, |
| lmk->sysref_mux)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_SYSREF_DDLY_LSB, |
| FIELD_GET(0x00ff, lmk->sysref_ddly)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_SYSREF_DDLY_MSB, |
| FIELD_GET(0x1f00, lmk->sysref_ddly)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_SYSREF_PULSE_CNT, |
| ilog2(lmk->sysref_pulse_cnt)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(lmk->regmap, LMK04832_REG_MAIN_PD, |
| LMK04832_BIT_SYSREF_DDLY_PD | |
| LMK04832_BIT_SYSREF_PLSR_PD, |
| FIELD_PREP(LMK04832_BIT_SYSREF_DDLY_PD, 0) | |
| FIELD_PREP(LMK04832_BIT_SYSREF_PLSR_PD, 0)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_SYNC, |
| FIELD_PREP(LMK04832_BIT_SYNC_POL, 0) | |
| FIELD_PREP(LMK04832_BIT_SYNC_EN, 1) | |
| FIELD_PREP(LMK04832_BIT_SYNC_MODE, lmk->sync_mode)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_SYNC_DIS, 0xff); |
| if (ret) |
| return ret; |
| |
| lmk->sclk.init = &init; |
| return devm_clk_hw_register(lmk->dev, &lmk->sclk); |
| } |
| |
| static int lmk04832_dclk_is_enabled(struct clk_hw *hw) |
| { |
| struct lmk_dclk *dclk = container_of(hw, struct lmk_dclk, hw); |
| struct lmk04832 *lmk = dclk->lmk; |
| unsigned int tmp; |
| int ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_CTRL3(dclk->id), |
| &tmp); |
| if (ret) |
| return ret; |
| |
| return !FIELD_GET(LMK04832_BIT_DCLKX_Y_PD, tmp); |
| } |
| |
| static int lmk04832_dclk_prepare(struct clk_hw *hw) |
| { |
| struct lmk_dclk *dclk = container_of(hw, struct lmk_dclk, hw); |
| struct lmk04832 *lmk = dclk->lmk; |
| |
| return regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_CTRL3(dclk->id), |
| LMK04832_BIT_DCLKX_Y_PD, 0x00); |
| } |
| |
| static void lmk04832_dclk_unprepare(struct clk_hw *hw) |
| { |
| struct lmk_dclk *dclk = container_of(hw, struct lmk_dclk, hw); |
| struct lmk04832 *lmk = dclk->lmk; |
| |
| regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_CTRL3(dclk->id), |
| LMK04832_BIT_DCLKX_Y_PD, 0xff); |
| } |
| |
| static unsigned long lmk04832_dclk_recalc_rate(struct clk_hw *hw, |
| unsigned long prate) |
| { |
| struct lmk_dclk *dclk = container_of(hw, struct lmk_dclk, hw); |
| struct lmk04832 *lmk = dclk->lmk; |
| unsigned int dclk_div; |
| unsigned int lsb, msb; |
| unsigned long rate; |
| int ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_CTRL0(dclk->id), |
| &lsb); |
| if (ret) |
| return ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_CTRL2(dclk->id), |
| &msb); |
| if (ret) |
| return ret; |
| |
| dclk_div = FIELD_GET(LMK04832_BIT_DCLK_DIV_MSB, msb) << 8 | lsb; |
| rate = DIV_ROUND_CLOSEST(prate, dclk_div); |
| |
| return rate; |
| } |
| |
| static long lmk04832_dclk_round_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long *prate) |
| { |
| struct lmk_dclk *dclk = container_of(hw, struct lmk_dclk, hw); |
| struct lmk04832 *lmk = dclk->lmk; |
| unsigned long dclk_rate; |
| unsigned int dclk_div; |
| |
| dclk_div = DIV_ROUND_CLOSEST(*prate, rate); |
| dclk_rate = DIV_ROUND_CLOSEST(*prate, dclk_div); |
| |
| if (dclk_div < 1 || dclk_div > 0x3ff) { |
| dev_err(lmk->dev, "%s_div out of range\n", clk_hw_get_name(hw)); |
| return -EINVAL; |
| } |
| |
| if (rate != dclk_rate) |
| return -EINVAL; |
| |
| return dclk_rate; |
| } |
| |
| static int lmk04832_dclk_set_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long prate) |
| { |
| struct lmk_dclk *dclk = container_of(hw, struct lmk_dclk, hw); |
| struct lmk04832 *lmk = dclk->lmk; |
| unsigned int dclk_div; |
| int ret; |
| |
| dclk_div = DIV_ROUND_CLOSEST(prate, rate); |
| |
| if (dclk_div > 0x3ff) { |
| dev_err(lmk->dev, "%s_div out of range\n", clk_hw_get_name(hw)); |
| return -EINVAL; |
| } |
| |
| /* Enable Duty Cycle Correction */ |
| if (dclk_div == 1) { |
| ret = regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_CTRL3(dclk->id), |
| LMK04832_BIT_DCLKX_Y_DCC, |
| FIELD_PREP(LMK04832_BIT_DCLKX_Y_DCC, 1)); |
| if (ret) |
| return ret; |
| } |
| |
| /* |
| * While using Divide-by-2 or Divide-by-3 for DCLK_X_Y_DIV, SYNC |
| * procedure requires to first program Divide-by-4 and then back to |
| * Divide-by-2 or Divide-by-3 before doing SYNC. |
| */ |
| if (dclk_div == 2 || dclk_div == 3) { |
| ret = regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_CTRL2(dclk->id), |
| LMK04832_BIT_DCLK_DIV_MSB, 0x00); |
| if (ret) |
| return ret; |
| |
| ret = regmap_write(lmk->regmap, |
| LMK04832_REG_CLKOUT_CTRL0(dclk->id), 0x04); |
| if (ret) |
| return ret; |
| } |
| |
| ret = regmap_write(lmk->regmap, LMK04832_REG_CLKOUT_CTRL0(dclk->id), |
| FIELD_GET(0x0ff, dclk_div)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_CTRL2(dclk->id), |
| LMK04832_BIT_DCLK_DIV_MSB, |
| FIELD_GET(0x300, dclk_div)); |
| if (ret) |
| return ret; |
| |
| ret = lmk04832_sclk_sync_sequence(lmk); |
| if (ret) |
| dev_err(lmk->dev, "SYNC sequence failed\n"); |
| |
| return ret; |
| } |
| |
| static const struct clk_ops lmk04832_dclk_ops = { |
| .is_enabled = lmk04832_dclk_is_enabled, |
| .prepare = lmk04832_dclk_prepare, |
| .unprepare = lmk04832_dclk_unprepare, |
| .recalc_rate = lmk04832_dclk_recalc_rate, |
| .round_rate = lmk04832_dclk_round_rate, |
| .set_rate = lmk04832_dclk_set_rate, |
| }; |
| |
| static int lmk04832_clkout_is_enabled(struct clk_hw *hw) |
| { |
| struct lmk_clkout *clkout = container_of(hw, struct lmk_clkout, hw); |
| struct lmk04832 *lmk = clkout->lmk; |
| unsigned int clkoutx_y_pd; |
| unsigned int sclkx_y_pd; |
| unsigned int tmp; |
| u32 enabled; |
| int ret; |
| u8 fmt; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_CTRL2(clkout->id), |
| &clkoutx_y_pd); |
| if (ret) |
| return ret; |
| |
| enabled = !FIELD_GET(LMK04832_BIT_CLKOUTX_Y_PD, clkoutx_y_pd); |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_SRC_MUX(clkout->id), |
| &tmp); |
| if (ret) |
| return ret; |
| |
| if (FIELD_GET(LMK04832_BIT_CLKOUT_SRC_MUX, tmp)) { |
| ret = regmap_read(lmk->regmap, |
| LMK04832_REG_CLKOUT_CTRL4(clkout->id), |
| &sclkx_y_pd); |
| if (ret) |
| return ret; |
| |
| enabled = enabled && !FIELD_GET(LMK04832_BIT_SCLK_PD, sclkx_y_pd); |
| } |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_FMT(clkout->id), |
| &tmp); |
| if (ret) |
| return ret; |
| |
| if (clkout->id % 2) |
| fmt = FIELD_GET(0xf0, tmp); |
| else |
| fmt = FIELD_GET(0x0f, tmp); |
| |
| return enabled && !fmt; |
| } |
| |
| static int lmk04832_clkout_prepare(struct clk_hw *hw) |
| { |
| struct lmk_clkout *clkout = container_of(hw, struct lmk_clkout, hw); |
| struct lmk04832 *lmk = clkout->lmk; |
| unsigned int tmp; |
| int ret; |
| |
| if (clkout->format == LMK04832_VAL_CLKOUT_FMT_POWERDOWN) |
| dev_err(lmk->dev, "prepared %s but format is powerdown\n", |
| clk_hw_get_name(hw)); |
| |
| ret = regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_CTRL2(clkout->id), |
| LMK04832_BIT_CLKOUTX_Y_PD, 0x00); |
| if (ret) |
| return ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_SRC_MUX(clkout->id), |
| &tmp); |
| if (ret) |
| return ret; |
| |
| if (FIELD_GET(LMK04832_BIT_CLKOUT_SRC_MUX, tmp)) { |
| ret = regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_CTRL4(clkout->id), |
| LMK04832_BIT_SCLK_PD, 0x00); |
| if (ret) |
| return ret; |
| } |
| |
| return regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_FMT(clkout->id), |
| LMK04832_BIT_CLKOUT_FMT(clkout->id), |
| clkout->format << 4 * (clkout->id % 2)); |
| } |
| |
| static void lmk04832_clkout_unprepare(struct clk_hw *hw) |
| { |
| struct lmk_clkout *clkout = container_of(hw, struct lmk_clkout, hw); |
| struct lmk04832 *lmk = clkout->lmk; |
| |
| regmap_update_bits(lmk->regmap, LMK04832_REG_CLKOUT_FMT(clkout->id), |
| LMK04832_BIT_CLKOUT_FMT(clkout->id), |
| 0x00); |
| } |
| |
| static int lmk04832_clkout_set_parent(struct clk_hw *hw, uint8_t index) |
| { |
| struct lmk_clkout *clkout = container_of(hw, struct lmk_clkout, hw); |
| struct lmk04832 *lmk = clkout->lmk; |
| |
| return regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_SRC_MUX(clkout->id), |
| LMK04832_BIT_CLKOUT_SRC_MUX, |
| FIELD_PREP(LMK04832_BIT_CLKOUT_SRC_MUX, |
| index)); |
| } |
| |
| static uint8_t lmk04832_clkout_get_parent(struct clk_hw *hw) |
| { |
| struct lmk_clkout *clkout = container_of(hw, struct lmk_clkout, hw); |
| struct lmk04832 *lmk = clkout->lmk; |
| unsigned int tmp; |
| int ret; |
| |
| ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_SRC_MUX(clkout->id), |
| &tmp); |
| if (ret) |
| return ret; |
| |
| return FIELD_GET(LMK04832_BIT_CLKOUT_SRC_MUX, tmp); |
| } |
| |
| static const struct clk_ops lmk04832_clkout_ops = { |
| .is_enabled = lmk04832_clkout_is_enabled, |
| .prepare = lmk04832_clkout_prepare, |
| .unprepare = lmk04832_clkout_unprepare, |
| .set_parent = lmk04832_clkout_set_parent, |
| .get_parent = lmk04832_clkout_get_parent, |
| }; |
| |
| static int lmk04832_register_clkout(struct lmk04832 *lmk, const int num) |
| { |
| char name[] = "lmk-clkoutXX"; |
| char dclk_name[] = "lmk-dclkXX_YY"; |
| const char *parent_names[2]; |
| struct clk_init_data init; |
| int dclk_num = num / 2; |
| int ret; |
| |
| if (num % 2 == 0) { |
| sprintf(dclk_name, "lmk-dclk%02d_%02d", num, num + 1); |
| init.name = dclk_name; |
| parent_names[0] = clk_hw_get_name(&lmk->vco); |
| init.ops = &lmk04832_dclk_ops; |
| init.flags = CLK_SET_RATE_PARENT; |
| init.num_parents = 1; |
| |
| lmk->dclk[dclk_num].id = num; |
| lmk->dclk[dclk_num].lmk = lmk; |
| lmk->dclk[dclk_num].hw.init = &init; |
| |
| ret = devm_clk_hw_register(lmk->dev, &lmk->dclk[dclk_num].hw); |
| if (ret) |
| return ret; |
| } else { |
| sprintf(dclk_name, "lmk-dclk%02d_%02d", num - 1, num); |
| } |
| |
| if (of_property_read_string_index(lmk->dev->of_node, |
| "clock-output-names", |
| num, &init.name)) { |
| sprintf(name, "lmk-clkout%02d", num); |
| init.name = name; |
| } |
| |
| parent_names[0] = dclk_name; |
| parent_names[1] = clk_hw_get_name(&lmk->sclk); |
| init.parent_names = parent_names; |
| init.ops = &lmk04832_clkout_ops; |
| init.flags = CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT; |
| init.num_parents = ARRAY_SIZE(parent_names); |
| |
| lmk->clkout[num].id = num; |
| lmk->clkout[num].lmk = lmk; |
| lmk->clkout[num].hw.init = &init; |
| lmk->clk_data->hws[num] = &lmk->clkout[num].hw; |
| |
| /* Set initial parent */ |
| regmap_update_bits(lmk->regmap, |
| LMK04832_REG_CLKOUT_SRC_MUX(num), |
| LMK04832_BIT_CLKOUT_SRC_MUX, |
| FIELD_PREP(LMK04832_BIT_CLKOUT_SRC_MUX, |
| lmk->clkout[num].sysref)); |
| |
| return devm_clk_hw_register(lmk->dev, &lmk->clkout[num].hw); |
| } |
| |
| static int lmk04832_set_spi_rdbk(const struct lmk04832 *lmk, const int rdbk_pin) |
| { |
| int reg; |
| int ret; |
| |
| dev_info(lmk->dev, "setting up 4-wire mode\n"); |
| ret = regmap_write(lmk->regmap, LMK04832_REG_RST3W, |
| LMK04832_BIT_SPI_3WIRE_DIS); |
| if (ret) |
| return ret; |
| |
| switch (rdbk_pin) { |
| case RDBK_CLKIN_SEL0: |
| reg = LMK04832_REG_CLKIN_SEL0; |
| break; |
| case RDBK_CLKIN_SEL1: |
| reg = LMK04832_REG_CLKIN_SEL1; |
| break; |
| case RDBK_RESET: |
| reg = LMK04832_REG_CLKIN_RST; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return regmap_write(lmk->regmap, reg, |
| FIELD_PREP(LMK04832_BIT_CLKIN_SEL_MUX, |
| LMK04832_VAL_CLKIN_SEL_MUX_SPI_RDBK) | |
| FIELD_PREP(LMK04832_BIT_CLKIN_SEL_TYPE, |
| LMK04832_VAL_CLKIN_SEL_TYPE_OUT)); |
| } |
| |
| static int lmk04832_probe(struct spi_device *spi) |
| { |
| const struct lmk04832_device_info *info; |
| int rdbk_pin = RDBK_CLKIN_SEL1; |
| struct device_node *child; |
| struct lmk04832 *lmk; |
| u8 tmp[3]; |
| int ret; |
| int i; |
| |
| info = &lmk04832_device_info[spi_get_device_id(spi)->driver_data]; |
| |
| lmk = devm_kzalloc(&spi->dev, sizeof(struct lmk04832), GFP_KERNEL); |
| if (!lmk) |
| return -ENOMEM; |
| |
| lmk->dev = &spi->dev; |
| |
| lmk->oscin = devm_clk_get(lmk->dev, "oscin"); |
| if (IS_ERR(lmk->oscin)) { |
| dev_err(lmk->dev, "failed to get oscin clock\n"); |
| return PTR_ERR(lmk->oscin); |
| } |
| |
| ret = clk_prepare_enable(lmk->oscin); |
| if (ret) |
| return ret; |
| |
| lmk->reset_gpio = devm_gpiod_get_optional(&spi->dev, "reset", |
| GPIOD_OUT_LOW); |
| |
| lmk->dclk = devm_kcalloc(lmk->dev, info->num_channels >> 1, |
| sizeof(struct lmk_dclk), GFP_KERNEL); |
| if (!lmk->dclk) { |
| ret = -ENOMEM; |
| goto err_disable_oscin; |
| } |
| |
| lmk->clkout = devm_kcalloc(lmk->dev, info->num_channels, |
| sizeof(*lmk->clkout), GFP_KERNEL); |
| if (!lmk->clkout) { |
| ret = -ENOMEM; |
| goto err_disable_oscin; |
| } |
| |
| lmk->clk_data = devm_kzalloc(lmk->dev, struct_size(lmk->clk_data, hws, |
| info->num_channels), |
| GFP_KERNEL); |
| if (!lmk->clk_data) { |
| ret = -ENOMEM; |
| goto err_disable_oscin; |
| } |
| |
| device_property_read_u32(lmk->dev, "ti,vco-hz", &lmk->vco_rate); |
| |
| lmk->sysref_ddly = 8; |
| device_property_read_u32(lmk->dev, "ti,sysref-ddly", &lmk->sysref_ddly); |
| |
| lmk->sysref_mux = LMK04832_VAL_SYSREF_MUX_CONTINUOUS; |
| device_property_read_u32(lmk->dev, "ti,sysref-mux", |
| &lmk->sysref_mux); |
| |
| lmk->sync_mode = LMK04832_VAL_SYNC_MODE_OFF; |
| device_property_read_u32(lmk->dev, "ti,sync-mode", |
| &lmk->sync_mode); |
| |
| lmk->sysref_pulse_cnt = 4; |
| device_property_read_u32(lmk->dev, "ti,sysref-pulse-count", |
| &lmk->sysref_pulse_cnt); |
| |
| for_each_child_of_node(lmk->dev->of_node, child) { |
| int reg; |
| |
| ret = of_property_read_u32(child, "reg", ®); |
| if (ret) { |
| dev_err(lmk->dev, "missing reg property in child: %s\n", |
| child->full_name); |
| of_node_put(child); |
| goto err_disable_oscin; |
| } |
| |
| of_property_read_u32(child, "ti,clkout-fmt", |
| &lmk->clkout[reg].format); |
| |
| if (lmk->clkout[reg].format >= 0x0a && reg % 2 == 0 |
| && reg != 8 && reg != 10) |
| dev_err(lmk->dev, "invalid format for clkout%02d\n", |
| reg); |
| |
| lmk->clkout[reg].sysref = |
| of_property_read_bool(child, "ti,clkout-sysref"); |
| } |
| |
| lmk->regmap = devm_regmap_init_spi(spi, ®map_config); |
| if (IS_ERR(lmk->regmap)) { |
| dev_err(lmk->dev, "%s: regmap allocation failed: %ld\n", |
| |
| __func__, PTR_ERR(lmk->regmap)); |
| ret = PTR_ERR(lmk->regmap); |
| goto err_disable_oscin; |
| } |
| |
| regmap_write(lmk->regmap, LMK04832_REG_RST3W, LMK04832_BIT_RESET); |
| |
| if (!(spi->mode & SPI_3WIRE)) { |
| device_property_read_u32(lmk->dev, "ti,spi-4wire-rdbk", |
| &rdbk_pin); |
| ret = lmk04832_set_spi_rdbk(lmk, rdbk_pin); |
| if (ret) |
| goto err_disable_oscin; |
| } |
| |
| regmap_bulk_read(lmk->regmap, LMK04832_REG_ID_PROD_MSB, &tmp, 3); |
| if ((tmp[0] << 8 | tmp[1]) != info->pid || tmp[2] != info->maskrev) { |
| dev_err(lmk->dev, "unsupported device type: pid 0x%04x, maskrev 0x%02x\n", |
| tmp[0] << 8 | tmp[1], tmp[2]); |
| ret = -EINVAL; |
| goto err_disable_oscin; |
| } |
| |
| ret = lmk04832_register_vco(lmk); |
| if (ret) { |
| dev_err(lmk->dev, "failed to init device clock path\n"); |
| goto err_disable_oscin; |
| } |
| |
| if (lmk->vco_rate) { |
| dev_info(lmk->dev, "setting VCO rate to %u Hz\n", lmk->vco_rate); |
| ret = clk_set_rate(lmk->vco.clk, lmk->vco_rate); |
| if (ret) { |
| dev_err(lmk->dev, "failed to set VCO rate\n"); |
| goto err_disable_vco; |
| } |
| } |
| |
| ret = lmk04832_register_sclk(lmk); |
| if (ret) { |
| dev_err(lmk->dev, "failed to init SYNC/SYSREF clock path\n"); |
| goto err_disable_vco; |
| } |
| |
| for (i = 0; i < info->num_channels; i++) { |
| ret = lmk04832_register_clkout(lmk, i); |
| if (ret) { |
| dev_err(lmk->dev, "failed to register clk %d\n", i); |
| goto err_disable_vco; |
| } |
| } |
| |
| lmk->clk_data->num = info->num_channels; |
| ret = of_clk_add_hw_provider(lmk->dev->of_node, of_clk_hw_onecell_get, |
| lmk->clk_data); |
| if (ret) { |
| dev_err(lmk->dev, "failed to add provider (%d)\n", ret); |
| goto err_disable_vco; |
| } |
| |
| spi_set_drvdata(spi, lmk); |
| |
| return 0; |
| |
| err_disable_vco: |
| clk_disable_unprepare(lmk->vco.clk); |
| |
| err_disable_oscin: |
| clk_disable_unprepare(lmk->oscin); |
| |
| return ret; |
| } |
| |
| static void lmk04832_remove(struct spi_device *spi) |
| { |
| struct lmk04832 *lmk = spi_get_drvdata(spi); |
| |
| clk_disable_unprepare(lmk->oscin); |
| of_clk_del_provider(spi->dev.of_node); |
| } |
| |
| static const struct spi_device_id lmk04832_id[] = { |
| { "lmk04832", LMK04832 }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(spi, lmk04832_id); |
| |
| static const struct of_device_id lmk04832_of_id[] = { |
| { .compatible = "ti,lmk04832" }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, lmk04832_of_id); |
| |
| static struct spi_driver lmk04832_driver = { |
| .driver = { |
| .name = "lmk04832", |
| .of_match_table = lmk04832_of_id, |
| }, |
| .probe = lmk04832_probe, |
| .remove = lmk04832_remove, |
| .id_table = lmk04832_id, |
| }; |
| module_spi_driver(lmk04832_driver); |
| |
| MODULE_AUTHOR("Liam Beguin <lvb@xiphos.com>"); |
| MODULE_DESCRIPTION("Texas Instruments LMK04832"); |
| MODULE_LICENSE("GPL v2"); |