| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2020 Theobroma Systems Design und Consulting GmbH |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/media-bus-format.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| #include <linux/regulator/consumer.h> |
| |
| #include <video/display_timing.h> |
| #include <video/mipi_display.h> |
| |
| #include <drm/drm_mipi_dsi.h> |
| #include <drm/drm_modes.h> |
| #include <drm/drm_panel.h> |
| |
| struct ltk050h3146w_cmd { |
| char cmd; |
| char data; |
| }; |
| |
| struct ltk050h3146w; |
| struct ltk050h3146w_desc { |
| const struct drm_display_mode *mode; |
| int (*init)(struct ltk050h3146w *ctx); |
| }; |
| |
| struct ltk050h3146w { |
| struct device *dev; |
| struct drm_panel panel; |
| struct gpio_desc *reset_gpio; |
| struct regulator *vci; |
| struct regulator *iovcc; |
| const struct ltk050h3146w_desc *panel_desc; |
| bool prepared; |
| }; |
| |
| static const struct ltk050h3146w_cmd page1_cmds[] = { |
| { 0x22, 0x0A }, /* BGR SS GS */ |
| { 0x31, 0x00 }, /* column inversion */ |
| { 0x53, 0xA2 }, /* VCOM1 */ |
| { 0x55, 0xA2 }, /* VCOM2 */ |
| { 0x50, 0x81 }, /* VREG1OUT=5V */ |
| { 0x51, 0x85 }, /* VREG2OUT=-5V */ |
| { 0x62, 0x0D }, /* EQT Time setting */ |
| /* |
| * The vendor init selected page 1 here _again_ |
| * Is this supposed to be page 2? |
| */ |
| { 0xA0, 0x00 }, |
| { 0xA1, 0x1A }, |
| { 0xA2, 0x28 }, |
| { 0xA3, 0x13 }, |
| { 0xA4, 0x16 }, |
| { 0xA5, 0x29 }, |
| { 0xA6, 0x1D }, |
| { 0xA7, 0x1E }, |
| { 0xA8, 0x84 }, |
| { 0xA9, 0x1C }, |
| { 0xAA, 0x28 }, |
| { 0xAB, 0x75 }, |
| { 0xAC, 0x1A }, |
| { 0xAD, 0x19 }, |
| { 0xAE, 0x4D }, |
| { 0xAF, 0x22 }, |
| { 0xB0, 0x28 }, |
| { 0xB1, 0x54 }, |
| { 0xB2, 0x66 }, |
| { 0xB3, 0x39 }, |
| { 0xC0, 0x00 }, |
| { 0xC1, 0x1A }, |
| { 0xC2, 0x28 }, |
| { 0xC3, 0x13 }, |
| { 0xC4, 0x16 }, |
| { 0xC5, 0x29 }, |
| { 0xC6, 0x1D }, |
| { 0xC7, 0x1E }, |
| { 0xC8, 0x84 }, |
| { 0xC9, 0x1C }, |
| { 0xCA, 0x28 }, |
| { 0xCB, 0x75 }, |
| { 0xCC, 0x1A }, |
| { 0xCD, 0x19 }, |
| { 0xCE, 0x4D }, |
| { 0xCF, 0x22 }, |
| { 0xD0, 0x28 }, |
| { 0xD1, 0x54 }, |
| { 0xD2, 0x66 }, |
| { 0xD3, 0x39 }, |
| }; |
| |
| static const struct ltk050h3146w_cmd page3_cmds[] = { |
| { 0x01, 0x00 }, |
| { 0x02, 0x00 }, |
| { 0x03, 0x73 }, |
| { 0x04, 0x00 }, |
| { 0x05, 0x00 }, |
| { 0x06, 0x0a }, |
| { 0x07, 0x00 }, |
| { 0x08, 0x00 }, |
| { 0x09, 0x01 }, |
| { 0x0a, 0x00 }, |
| { 0x0b, 0x00 }, |
| { 0x0c, 0x01 }, |
| { 0x0d, 0x00 }, |
| { 0x0e, 0x00 }, |
| { 0x0f, 0x1d }, |
| { 0x10, 0x1d }, |
| { 0x11, 0x00 }, |
| { 0x12, 0x00 }, |
| { 0x13, 0x00 }, |
| { 0x14, 0x00 }, |
| { 0x15, 0x00 }, |
| { 0x16, 0x00 }, |
| { 0x17, 0x00 }, |
| { 0x18, 0x00 }, |
| { 0x19, 0x00 }, |
| { 0x1a, 0x00 }, |
| { 0x1b, 0x00 }, |
| { 0x1c, 0x00 }, |
| { 0x1d, 0x00 }, |
| { 0x1e, 0x40 }, |
| { 0x1f, 0x80 }, |
| { 0x20, 0x06 }, |
| { 0x21, 0x02 }, |
| { 0x22, 0x00 }, |
| { 0x23, 0x00 }, |
| { 0x24, 0x00 }, |
| { 0x25, 0x00 }, |
| { 0x26, 0x00 }, |
| { 0x27, 0x00 }, |
| { 0x28, 0x33 }, |
| { 0x29, 0x03 }, |
| { 0x2a, 0x00 }, |
| { 0x2b, 0x00 }, |
| { 0x2c, 0x00 }, |
| { 0x2d, 0x00 }, |
| { 0x2e, 0x00 }, |
| { 0x2f, 0x00 }, |
| { 0x30, 0x00 }, |
| { 0x31, 0x00 }, |
| { 0x32, 0x00 }, |
| { 0x33, 0x00 }, |
| { 0x34, 0x04 }, |
| { 0x35, 0x00 }, |
| { 0x36, 0x00 }, |
| { 0x37, 0x00 }, |
| { 0x38, 0x3C }, |
| { 0x39, 0x35 }, |
| { 0x3A, 0x01 }, |
| { 0x3B, 0x40 }, |
| { 0x3C, 0x00 }, |
| { 0x3D, 0x01 }, |
| { 0x3E, 0x00 }, |
| { 0x3F, 0x00 }, |
| { 0x40, 0x00 }, |
| { 0x41, 0x88 }, |
| { 0x42, 0x00 }, |
| { 0x43, 0x00 }, |
| { 0x44, 0x1F }, |
| { 0x50, 0x01 }, |
| { 0x51, 0x23 }, |
| { 0x52, 0x45 }, |
| { 0x53, 0x67 }, |
| { 0x54, 0x89 }, |
| { 0x55, 0xab }, |
| { 0x56, 0x01 }, |
| { 0x57, 0x23 }, |
| { 0x58, 0x45 }, |
| { 0x59, 0x67 }, |
| { 0x5a, 0x89 }, |
| { 0x5b, 0xab }, |
| { 0x5c, 0xcd }, |
| { 0x5d, 0xef }, |
| { 0x5e, 0x11 }, |
| { 0x5f, 0x01 }, |
| { 0x60, 0x00 }, |
| { 0x61, 0x15 }, |
| { 0x62, 0x14 }, |
| { 0x63, 0x0E }, |
| { 0x64, 0x0F }, |
| { 0x65, 0x0C }, |
| { 0x66, 0x0D }, |
| { 0x67, 0x06 }, |
| { 0x68, 0x02 }, |
| { 0x69, 0x07 }, |
| { 0x6a, 0x02 }, |
| { 0x6b, 0x02 }, |
| { 0x6c, 0x02 }, |
| { 0x6d, 0x02 }, |
| { 0x6e, 0x02 }, |
| { 0x6f, 0x02 }, |
| { 0x70, 0x02 }, |
| { 0x71, 0x02 }, |
| { 0x72, 0x02 }, |
| { 0x73, 0x02 }, |
| { 0x74, 0x02 }, |
| { 0x75, 0x01 }, |
| { 0x76, 0x00 }, |
| { 0x77, 0x14 }, |
| { 0x78, 0x15 }, |
| { 0x79, 0x0E }, |
| { 0x7a, 0x0F }, |
| { 0x7b, 0x0C }, |
| { 0x7c, 0x0D }, |
| { 0x7d, 0x06 }, |
| { 0x7e, 0x02 }, |
| { 0x7f, 0x07 }, |
| { 0x80, 0x02 }, |
| { 0x81, 0x02 }, |
| { 0x82, 0x02 }, |
| { 0x83, 0x02 }, |
| { 0x84, 0x02 }, |
| { 0x85, 0x02 }, |
| { 0x86, 0x02 }, |
| { 0x87, 0x02 }, |
| { 0x88, 0x02 }, |
| { 0x89, 0x02 }, |
| { 0x8A, 0x02 }, |
| }; |
| |
| static const struct ltk050h3146w_cmd page4_cmds[] = { |
| { 0x70, 0x00 }, |
| { 0x71, 0x00 }, |
| { 0x82, 0x0F }, /* VGH_MOD clamp level=15v */ |
| { 0x84, 0x0F }, /* VGH clamp level 15V */ |
| { 0x85, 0x0D }, /* VGL clamp level (-10V) */ |
| { 0x32, 0xAC }, |
| { 0x8C, 0x80 }, |
| { 0x3C, 0xF5 }, |
| { 0xB5, 0x07 }, /* GAMMA OP */ |
| { 0x31, 0x45 }, /* SOURCE OP */ |
| { 0x3A, 0x24 }, /* PS_EN OFF */ |
| { 0x88, 0x33 }, /* LVD */ |
| }; |
| |
| static inline |
| struct ltk050h3146w *panel_to_ltk050h3146w(struct drm_panel *panel) |
| { |
| return container_of(panel, struct ltk050h3146w, panel); |
| } |
| |
| #define dsi_dcs_write_seq(dsi, cmd, seq...) do { \ |
| static const u8 b[] = { cmd, seq }; \ |
| int ret; \ |
| ret = mipi_dsi_dcs_write_buffer(dsi, b, ARRAY_SIZE(b)); \ |
| if (ret < 0) \ |
| return ret; \ |
| } while (0) |
| |
| static int ltk050h3146w_init_sequence(struct ltk050h3146w *ctx) |
| { |
| struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); |
| int ret; |
| |
| /* |
| * Init sequence was supplied by the panel vendor without much |
| * documentation. |
| */ |
| dsi_dcs_write_seq(dsi, 0xdf, 0x93, 0x65, 0xf8); |
| dsi_dcs_write_seq(dsi, 0xb0, 0x01, 0x03, 0x02, 0x00, 0x64, 0x06, |
| 0x01); |
| dsi_dcs_write_seq(dsi, 0xb2, 0x00, 0xb5); |
| dsi_dcs_write_seq(dsi, 0xb3, 0x00, 0xb5); |
| dsi_dcs_write_seq(dsi, 0xb7, 0x00, 0xbf, 0x00, 0x00, 0xbf, 0x00); |
| |
| dsi_dcs_write_seq(dsi, 0xb9, 0x00, 0xc4, 0x23, 0x07); |
| dsi_dcs_write_seq(dsi, 0xbb, 0x02, 0x01, 0x24, 0x00, 0x28, 0x0f, |
| 0x28, 0x04, 0xcc, 0xcc, 0xcc); |
| dsi_dcs_write_seq(dsi, 0xbc, 0x0f, 0x04); |
| dsi_dcs_write_seq(dsi, 0xbe, 0x1e, 0xf2); |
| dsi_dcs_write_seq(dsi, 0xc0, 0x26, 0x03); |
| dsi_dcs_write_seq(dsi, 0xc1, 0x00, 0x12); |
| dsi_dcs_write_seq(dsi, 0xc3, 0x04, 0x02, 0x02, 0x76, 0x01, 0x80, |
| 0x80); |
| dsi_dcs_write_seq(dsi, 0xc4, 0x24, 0x80, 0xb4, 0x81, 0x12, 0x0f, |
| 0x16, 0x00, 0x00); |
| dsi_dcs_write_seq(dsi, 0xc8, 0x7f, 0x72, 0x67, 0x5d, 0x5d, 0x50, |
| 0x56, 0x41, 0x59, 0x57, 0x55, 0x70, 0x5b, 0x5f, |
| 0x4f, 0x47, 0x38, 0x23, 0x08, 0x7f, 0x72, 0x67, |
| 0x5d, 0x5d, 0x50, 0x56, 0x41, 0x59, 0x57, 0x55, |
| 0x70, 0x5b, 0x5f, 0x4f, 0x47, 0x38, 0x23, 0x08); |
| dsi_dcs_write_seq(dsi, 0xd0, 0x1e, 0x1f, 0x57, 0x58, 0x48, 0x4a, |
| 0x44, 0x46, 0x40, 0x1f, 0x42, 0x1f, 0x1f, 0x1f, |
| 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f); |
| dsi_dcs_write_seq(dsi, 0xd1, 0x1e, 0x1f, 0x57, 0x58, 0x49, 0x4b, |
| 0x45, 0x47, 0x41, 0x1f, 0x43, 0x1f, 0x1f, 0x1f, |
| 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f); |
| dsi_dcs_write_seq(dsi, 0xd2, 0x1f, 0x1e, 0x17, 0x18, 0x07, 0x05, |
| 0x0b, 0x09, 0x03, 0x1f, 0x01, 0x1f, 0x1f, 0x1f, |
| 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f); |
| dsi_dcs_write_seq(dsi, 0xd3, 0x1f, 0x1e, 0x17, 0x18, 0x06, 0x04, |
| 0x0a, 0x08, 0x02, 0x1f, 0x00, 0x1f, 0x1f, 0x1f, |
| 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f); |
| dsi_dcs_write_seq(dsi, 0xd4, 0x00, 0x00, 0x00, 0x0c, 0x06, 0x20, |
| 0x01, 0x02, 0x00, 0x60, 0x15, 0xb0, 0x30, 0x03, |
| 0x04, 0x00, 0x60, 0x72, 0x0a, 0x00, 0x60, 0x08); |
| dsi_dcs_write_seq(dsi, 0xd5, 0x00, 0x06, 0x06, 0x00, 0x30, 0x00, |
| 0x00, 0x00, 0x00, 0x00, 0xbc, 0x50, 0x00, 0x05, |
| 0x21, 0x00, 0x60); |
| dsi_dcs_write_seq(dsi, 0xdd, 0x2c, 0xa3, 0x00); |
| dsi_dcs_write_seq(dsi, 0xde, 0x02); |
| dsi_dcs_write_seq(dsi, 0xb2, 0x32, 0x1c); |
| dsi_dcs_write_seq(dsi, 0xb7, 0x3b, 0x70, 0x00, 0x04); |
| dsi_dcs_write_seq(dsi, 0xc1, 0x11); |
| dsi_dcs_write_seq(dsi, 0xbb, 0x21, 0x22, 0x23, 0x24, 0x36, 0x37); |
| dsi_dcs_write_seq(dsi, 0xc2, 0x20, 0x38, 0x1e, 0x84); |
| dsi_dcs_write_seq(dsi, 0xde, 0x00); |
| |
| ret = mipi_dsi_dcs_set_tear_on(dsi, 1); |
| if (ret < 0) { |
| dev_err(ctx->dev, "failed to set tear on: %d\n", ret); |
| return ret; |
| } |
| |
| msleep(60); |
| |
| return 0; |
| } |
| |
| static const struct drm_display_mode ltk050h3146w_mode = { |
| .hdisplay = 720, |
| .hsync_start = 720 + 42, |
| .hsync_end = 720 + 42 + 8, |
| .htotal = 720 + 42 + 8 + 42, |
| .vdisplay = 1280, |
| .vsync_start = 1280 + 12, |
| .vsync_end = 1280 + 12 + 4, |
| .vtotal = 1280 + 12 + 4 + 18, |
| .clock = 64018, |
| .width_mm = 62, |
| .height_mm = 110, |
| }; |
| |
| static const struct ltk050h3146w_desc ltk050h3146w_data = { |
| .mode = <k050h3146w_mode, |
| .init = ltk050h3146w_init_sequence, |
| }; |
| |
| static int ltk050h3146w_a2_select_page(struct ltk050h3146w *ctx, int page) |
| { |
| struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); |
| u8 d[3] = { 0x98, 0x81, page }; |
| |
| return mipi_dsi_dcs_write(dsi, 0xff, d, ARRAY_SIZE(d)); |
| } |
| |
| static int ltk050h3146w_a2_write_page(struct ltk050h3146w *ctx, int page, |
| const struct ltk050h3146w_cmd *cmds, |
| int num) |
| { |
| struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); |
| int i, ret; |
| |
| ret = ltk050h3146w_a2_select_page(ctx, page); |
| if (ret < 0) { |
| dev_err(ctx->dev, "failed to select page %d: %d\n", page, ret); |
| return ret; |
| } |
| |
| for (i = 0; i < num; i++) { |
| ret = mipi_dsi_generic_write(dsi, &cmds[i], |
| sizeof(struct ltk050h3146w_cmd)); |
| if (ret < 0) { |
| dev_err(ctx->dev, "failed to write page %d init cmds: %d\n", page, ret); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int ltk050h3146w_a2_init_sequence(struct ltk050h3146w *ctx) |
| { |
| struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); |
| int ret; |
| |
| /* |
| * Init sequence was supplied by the panel vendor without much |
| * documentation. |
| */ |
| ret = ltk050h3146w_a2_write_page(ctx, 3, page3_cmds, |
| ARRAY_SIZE(page3_cmds)); |
| if (ret < 0) |
| return ret; |
| |
| ret = ltk050h3146w_a2_write_page(ctx, 4, page4_cmds, |
| ARRAY_SIZE(page4_cmds)); |
| if (ret < 0) |
| return ret; |
| |
| ret = ltk050h3146w_a2_write_page(ctx, 1, page1_cmds, |
| ARRAY_SIZE(page1_cmds)); |
| if (ret < 0) |
| return ret; |
| |
| ret = ltk050h3146w_a2_select_page(ctx, 0); |
| if (ret < 0) { |
| dev_err(ctx->dev, "failed to select page 0: %d\n", ret); |
| return ret; |
| } |
| |
| /* vendor code called this without param, where there should be one */ |
| ret = mipi_dsi_dcs_set_tear_on(dsi, 0); |
| if (ret < 0) { |
| dev_err(ctx->dev, "failed to set tear on: %d\n", ret); |
| return ret; |
| } |
| |
| msleep(60); |
| |
| return 0; |
| } |
| |
| static const struct drm_display_mode ltk050h3146w_a2_mode = { |
| .hdisplay = 720, |
| .hsync_start = 720 + 42, |
| .hsync_end = 720 + 42 + 10, |
| .htotal = 720 + 42 + 10 + 60, |
| .vdisplay = 1280, |
| .vsync_start = 1280 + 18, |
| .vsync_end = 1280 + 18 + 4, |
| .vtotal = 1280 + 18 + 4 + 12, |
| .clock = 65595, |
| .width_mm = 62, |
| .height_mm = 110, |
| }; |
| |
| static const struct ltk050h3146w_desc ltk050h3146w_a2_data = { |
| .mode = <k050h3146w_a2_mode, |
| .init = ltk050h3146w_a2_init_sequence, |
| }; |
| |
| static int ltk050h3146w_unprepare(struct drm_panel *panel) |
| { |
| struct ltk050h3146w *ctx = panel_to_ltk050h3146w(panel); |
| struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); |
| int ret; |
| |
| if (!ctx->prepared) |
| return 0; |
| |
| ret = mipi_dsi_dcs_set_display_off(dsi); |
| if (ret < 0) { |
| dev_err(ctx->dev, "failed to set display off: %d\n", ret); |
| return ret; |
| } |
| |
| mipi_dsi_dcs_enter_sleep_mode(dsi); |
| if (ret < 0) { |
| dev_err(ctx->dev, "failed to enter sleep mode: %d\n", ret); |
| return ret; |
| } |
| |
| regulator_disable(ctx->iovcc); |
| regulator_disable(ctx->vci); |
| |
| ctx->prepared = false; |
| |
| return 0; |
| } |
| |
| static int ltk050h3146w_prepare(struct drm_panel *panel) |
| { |
| struct ltk050h3146w *ctx = panel_to_ltk050h3146w(panel); |
| struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); |
| int ret; |
| |
| if (ctx->prepared) |
| return 0; |
| |
| dev_dbg(ctx->dev, "Resetting the panel\n"); |
| ret = regulator_enable(ctx->vci); |
| if (ret < 0) { |
| dev_err(ctx->dev, "Failed to enable vci supply: %d\n", ret); |
| return ret; |
| } |
| ret = regulator_enable(ctx->iovcc); |
| if (ret < 0) { |
| dev_err(ctx->dev, "Failed to enable iovcc supply: %d\n", ret); |
| goto disable_vci; |
| } |
| |
| gpiod_set_value_cansleep(ctx->reset_gpio, 1); |
| usleep_range(5000, 6000); |
| gpiod_set_value_cansleep(ctx->reset_gpio, 0); |
| msleep(20); |
| |
| ret = ctx->panel_desc->init(ctx); |
| if (ret < 0) { |
| dev_err(ctx->dev, "Panel init sequence failed: %d\n", ret); |
| goto disable_iovcc; |
| } |
| |
| ret = mipi_dsi_dcs_exit_sleep_mode(dsi); |
| if (ret < 0) { |
| dev_err(ctx->dev, "Failed to exit sleep mode: %d\n", ret); |
| goto disable_iovcc; |
| } |
| |
| /* T9: 120ms */ |
| msleep(120); |
| |
| ret = mipi_dsi_dcs_set_display_on(dsi); |
| if (ret < 0) { |
| dev_err(ctx->dev, "Failed to set display on: %d\n", ret); |
| goto disable_iovcc; |
| } |
| |
| msleep(50); |
| |
| ctx->prepared = true; |
| |
| return 0; |
| |
| disable_iovcc: |
| regulator_disable(ctx->iovcc); |
| disable_vci: |
| regulator_disable(ctx->vci); |
| return ret; |
| } |
| |
| static int ltk050h3146w_get_modes(struct drm_panel *panel, |
| struct drm_connector *connector) |
| { |
| struct ltk050h3146w *ctx = panel_to_ltk050h3146w(panel); |
| struct drm_display_mode *mode; |
| |
| mode = drm_mode_duplicate(connector->dev, ctx->panel_desc->mode); |
| if (!mode) |
| return -ENOMEM; |
| |
| drm_mode_set_name(mode); |
| |
| mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; |
| connector->display_info.width_mm = mode->width_mm; |
| connector->display_info.height_mm = mode->height_mm; |
| drm_mode_probed_add(connector, mode); |
| |
| return 1; |
| } |
| |
| static const struct drm_panel_funcs ltk050h3146w_funcs = { |
| .unprepare = ltk050h3146w_unprepare, |
| .prepare = ltk050h3146w_prepare, |
| .get_modes = ltk050h3146w_get_modes, |
| }; |
| |
| static int ltk050h3146w_probe(struct mipi_dsi_device *dsi) |
| { |
| struct device *dev = &dsi->dev; |
| struct ltk050h3146w *ctx; |
| int ret; |
| |
| ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); |
| if (!ctx) |
| return -ENOMEM; |
| |
| ctx->panel_desc = of_device_get_match_data(dev); |
| if (!ctx->panel_desc) |
| return -EINVAL; |
| |
| ctx->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); |
| if (IS_ERR(ctx->reset_gpio)) { |
| dev_err(dev, "cannot get reset gpio\n"); |
| return PTR_ERR(ctx->reset_gpio); |
| } |
| |
| ctx->vci = devm_regulator_get(dev, "vci"); |
| if (IS_ERR(ctx->vci)) { |
| ret = PTR_ERR(ctx->vci); |
| if (ret != -EPROBE_DEFER) |
| dev_err(dev, "Failed to request vci regulator: %d\n", ret); |
| return ret; |
| } |
| |
| ctx->iovcc = devm_regulator_get(dev, "iovcc"); |
| if (IS_ERR(ctx->iovcc)) { |
| ret = PTR_ERR(ctx->iovcc); |
| if (ret != -EPROBE_DEFER) |
| dev_err(dev, "Failed to request iovcc regulator: %d\n", ret); |
| return ret; |
| } |
| |
| mipi_dsi_set_drvdata(dsi, ctx); |
| |
| ctx->dev = dev; |
| |
| dsi->lanes = 4; |
| dsi->format = MIPI_DSI_FMT_RGB888; |
| dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | |
| MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET; |
| |
| drm_panel_init(&ctx->panel, &dsi->dev, <k050h3146w_funcs, |
| DRM_MODE_CONNECTOR_DSI); |
| |
| ret = drm_panel_of_backlight(&ctx->panel); |
| if (ret) |
| return ret; |
| |
| drm_panel_add(&ctx->panel); |
| |
| ret = mipi_dsi_attach(dsi); |
| if (ret < 0) { |
| dev_err(dev, "mipi_dsi_attach failed: %d\n", ret); |
| drm_panel_remove(&ctx->panel); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void ltk050h3146w_shutdown(struct mipi_dsi_device *dsi) |
| { |
| struct ltk050h3146w *ctx = mipi_dsi_get_drvdata(dsi); |
| int ret; |
| |
| ret = drm_panel_unprepare(&ctx->panel); |
| if (ret < 0) |
| dev_err(&dsi->dev, "Failed to unprepare panel: %d\n", ret); |
| |
| ret = drm_panel_disable(&ctx->panel); |
| if (ret < 0) |
| dev_err(&dsi->dev, "Failed to disable panel: %d\n", ret); |
| } |
| |
| static void ltk050h3146w_remove(struct mipi_dsi_device *dsi) |
| { |
| struct ltk050h3146w *ctx = mipi_dsi_get_drvdata(dsi); |
| int ret; |
| |
| ltk050h3146w_shutdown(dsi); |
| |
| ret = mipi_dsi_detach(dsi); |
| if (ret < 0) |
| dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret); |
| |
| drm_panel_remove(&ctx->panel); |
| } |
| |
| static const struct of_device_id ltk050h3146w_of_match[] = { |
| { |
| .compatible = "leadtek,ltk050h3146w", |
| .data = <k050h3146w_data, |
| }, |
| { |
| .compatible = "leadtek,ltk050h3146w-a2", |
| .data = <k050h3146w_a2_data, |
| }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, ltk050h3146w_of_match); |
| |
| static struct mipi_dsi_driver ltk050h3146w_driver = { |
| .driver = { |
| .name = "panel-leadtek-ltk050h3146w", |
| .of_match_table = ltk050h3146w_of_match, |
| }, |
| .probe = ltk050h3146w_probe, |
| .remove = ltk050h3146w_remove, |
| .shutdown = ltk050h3146w_shutdown, |
| }; |
| module_mipi_dsi_driver(ltk050h3146w_driver); |
| |
| MODULE_AUTHOR("Heiko Stuebner <heiko.stuebner@theobroma-systems.com>"); |
| MODULE_DESCRIPTION("DRM driver for Leadtek LTK050H3146W MIPI DSI panel"); |
| MODULE_LICENSE("GPL v2"); |